Features * High-performance, Low-power Atmel(R)AVR(R) 8-bit Microcontroller * Advanced RISC Architecture * * * * * * * - 130 Powerful Instructions - Most Single-clock Cycle Execution - 32 x 8 General Purpose Working Registers - Fully Static Operation - Up to 16 MIPS Throughput at 16MHz - On-chip 2-cycle Multiplier High Endurance Non-volatile Memory segments - 8Kbytes of In-System Self-programmable Flash program memory - 512Bytes EEPROM - 1Kbyte Internal SRAM - Write/Erase Cycles: 10,000 Flash/100,000 EEPROM - Data retention: 20 years at 85C/100 years at 25C(1) - Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation - Programming Lock for Software Security Peripheral Features - Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode - One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode - Real Time Counter with Separate Oscillator - Three PWM Channels - 8-channel ADC in TQFP and QFN/MLF package Eight Channels 10-bit Accuracy - 6-channel ADC in PDIP package Six Channels 10-bit Accuracy - Byte-oriented Two-wire Serial Interface - Programmable Serial USART - Master/Slave SPI Serial Interface - Programmable Watchdog Timer with Separate On-chip Oscillator - On-chip Analog Comparator Special Microcontroller Features - Power-on Reset and Programmable Brown-out Detection - Internal Calibrated RC Oscillator - External and Internal Interrupt Sources - Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby I/O and Packages - 23 Programmable I/O Lines - 28-lead PDIP, 32-lead TQFP, and 32-pad QFN/MLF Operating Voltages - 2.7V - 5.5V (ATmega8L) - 4.5V - 5.5V (ATmega8) Speed Grades - 0 - 8MHz (ATmega8L) - 0 - 16MHz (ATmega8) Power Consumption at 4Mhz, 3V, 25C - Active: 3.6mA - Idle Mode: 1.0mA - Power-down Mode: 0.5A 8-bit with 8KBytes InSystem Programmable Flash ATmega8 ATmega8L Summary Rev. 2486ZS-AVR-02/11 ATmega8(L) Pin Configurations PDIP (RESET) PC6 (RXD) PD0 (TXD) PD1 (INT0) PD2 (INT1) PD3 (XCK/T0) PD4 VCC GND (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7 (T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2) PC1 (ADC1) PC0 (ADC0) GND AREF AVCC PB5 (SCK) PB4 (MISO) PB3 (MOSI/OC2) PB2 (SS/OC1B) PB1 (OC1A) 32 31 30 29 28 27 26 25 PD2 (INT0) PD1 (TXD) PD0 (RXD) PC6 (RESET) PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2) TQFP Top View 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 PC1 (ADC1) PC0 (ADC0) ADC7 GND AREF ADC6 AVCC PB5 (SCK) 24 23 22 21 20 19 18 17 PC1 (ADC1) PC0 (ADC0) ADC7 GND AREF ADC6 AVCC PB5 (SCK) (T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 (OC1A) PB1 (SS/OC1B) PB2 (MOSI/OC2) PB3 (MISO) PB4 9 10 11 12 13 14 15 16 (INT1) PD3 (XCK/T0) PD4 GND VCC GND VCC (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7 32 31 30 29 28 27 26 25 PD2 (INT0) PD1 (TXD) PD0 (RXD) PC6 (RESET) PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2) MLF Top View 1 2 3 4 5 6 7 8 (T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 (OC1A) PB1 (SS/OC1B) PB2 (MOSI/OC2) PB3 (MISO) PB4 9 10 11 12 13 14 15 16 (INT1) PD3 (XCK/T0) PD4 GND VCC GND VCC (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7 NOTE: The large center pad underneath the MLF packages is made of metal and internally connected to GND. It should be soldered or glued to the PCB to ensure good mechanical stability. If the center pad is left unconneted, the package might loosen from the PCB. 2 2486ZS-AVR-02/11 ATmega8(L) Overview The ATmega8 is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8 achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed. Block Diagram Figure 1. Block Diagram XTAL1 RESET PC0 - PC6 PB0 - PB7 VCC XTAL2 GND PORTC DRIVERS/BUFFERS PORTB DRIVERS/BUFFERS PORTC DIGITAL INTERFACE PORTB DIGITAL INTERFACE MUX & ADC ADC INTERFACE PROGRAM COUNTER STACK POINTER PROGRAM FLASH SRAM TWI AGND AREF INSTRUCTION REGISTER GENERAL PURPOSE REGISTERS TIMERS/ COUNTERS OSCILLATOR INTERNAL OSCILLATOR WATCHDOG TIMER OSCILLATOR X INSTRUCTION DECODER Y MCU CTRL. & TIMING Z CONTROL LINES ALU INTERRUPT UNIT AVR CPU STATUS REGISTER EEPROM PROGRAMMING LOGIC SPI USART + - COMP. INTERFACE PORTD DIGITAL INTERFACE PORTD DRIVERS/BUFFERS PD0 - PD7 3 2486ZS-AVR-02/11 ATmega8(L) The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega8 provides the following features: 8 Kbytes of In-System Programmable Flash with Read-While-Write capabilities, 512 bytes of EEPROM, 1 Kbyte of SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, a byte oriented Twowire Serial Interface, a 6-channel ADC (eight channels in TQFP and QFN/MLF packages) with 10-bit accuracy, a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and five software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Powerdown mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next Interrupt or Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. The device is manufactured using Atmel's high density non-volatile memory technology. The Flash Program memory can be reprogrammed In-System through an SPI serial interface, by a conventional non-volatile memory programmer, or by an On-chip boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash Section will continue to run while the Application Flash Section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega8 is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications. The ATmega8 AVR is supported with a full suite of program and system development tools, including C compilers, macro assemblers, program debugger/simulators, In-Circuit Emulators, and evaluation kits. Disclaimer Typical values contained in this datasheet are based on simulations and characterization of other AVR microcontrollers manufactured on the same process technology. Minimum and Maximum values will be available after the device is characterized. 4 2486ZS-AVR-02/11 ATmega8(L) Pin Descriptions VCC Digital supply voltage. GND Ground. Port B (PB7..PB0) XTAL1/XTAL2/TOSC1/ TOSC2 Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscillator amplifier and input to the internal clock operating circuit. Depending on the clock selection fuse settings, PB7 can be used as output from the inverting Oscillator amplifier. If the Internal Calibrated RC Oscillator is used as chip clock source, PB7..6 is used as TOSC2..1 input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set. The various special features of Port B are elaborated in "Alternate Functions of Port B" on page 58 and "System Clock and Clock Options" on page 25. Port C (PC5..PC0) Port C is an 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. PC6/RESET If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical characteristics of PC6 differ from those of the other pins of Port C. If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin for longer than the minimum pulse length will generate a Reset, even if the clock is not running. The minimum pulse length is given in Table 15 on page 38. Shorter pulses are not guaranteed to generate a Reset. The various special features of Port C are elaborated on page 61. Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega8 as listed on page 63. RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in Table 15 on page 38. Shorter pulses are not guaranteed to generate a reset. 5 2486ZS-AVR-02/11 ATmega8(L) AVCC AVCC is the supply voltage pin for the A/D Converter, Port C (3..0), and ADC (7..6). It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. Note that Port C (5..4) use digital supply voltage, VCC. AREF AREF is the analog reference pin for the A/D Converter. ADC7..6 (TQFP and QFN/MLF Package Only) In the TQFP and QFN/MLF package, ADC7..6 serve as analog inputs to the A/D converter. These pins are powered from the analog supply and serve as 10-bit ADC channels. 6 2486ZS-AVR-02/11 ATmega8(L) Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. Note: Data Retention 1. Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM over 20 years at 85C or 100 years at 25C. 7 2486ZS-AVR-02/11 ATmega8(L) Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x3F (0x5F) SREG I T H S V N Z C 11 0x3E (0x5E) SPH - - - - - SP10 SP9 SP8 13 0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 13 0x3C (0x5C) Reserved 0x3B (0x5B) GICR INT1 INT0 - - - - IVSEL IVCE 49, 67 0x3A (0x5A) GIFR INTF1 INTF0 - - - - - - 67 0x39 (0x59) TIMSK OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 - TOIE0 72, 100, 119 0x38 (0x58) TIFR OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 - TOV0 72, 101, 119 0x37 (0x57) SPMCR SPMIE RWWSB - RWWSRE BLBSET PGWRT PGERS SPMEN 206 0x36 (0x56) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN - TWIE 165 0x35 (0x55) MCUCR SE SM2 SM1 SM0 ISC11 ISC10 ISC01 ISC00 33, 66 0x34 (0x54) MCUCSR - - - - WDRF BORF EXTRF PORF 41 0x33 (0x53) TCCR0 - - - - - CS02 CS01 CS00 71 0x32 (0x52) TCNT0 Timer/Counter0 (8 Bits) 0x31 (0x51) OSCCAL Oscillator Calibration Register 0x30 (0x50) SFIOR - - - - 72 31 ACME PUD PSR2 PSR10 58, 74, 120, 186 0x2F (0x4F) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 FOC1A FOC1B WGM11 WGM10 96 0x2E (0x4E) TCCR1B ICNC1 ICES1 - WGM13 WGM12 CS12 CS11 CS10 98 0x2D (0x4D) TCNT1H Timer/Counter1 - Counter Register High byte 99 0x2C (0x4C) TCNT1L 99 0x2B (0x4B) OCR1AH Timer/Counter1 - Counter Register Low byte Timer/Counter1 - Output Compare Register A High byte 0x2A (0x4A) OCR1AL Timer/Counter1 - Output Compare Register A Low byte 99 0x29 (0x49) OCR1BH Timer/Counter1 - Output Compare Register B High byte 99 0x28 (0x48) OCR1BL Timer/Counter1 - Output Compare Register B Low byte 99 0x27 (0x47) ICR1H Timer/Counter1 - Input Capture Register High byte 100 0x26 (0x46) ICR1L Timer/Counter1 - Input Capture Register Low byte 0x25 (0x45) TCCR2 0x24 (0x44) TCNT2 0x23 (0x43) OCR2 0x22 (0x42) ASSR - - - - AS2 TCN2UB OCR2UB TCR2UB 0x21 (0x41) WDTCR - - - WDCE WDE WDP2 WDP1 WDP0 UBRRH URSEL - - - 0x20(1) (0x40)(1) FOC2 WGM20 COM21 COM20 WGM21 99 100 CS22 CS21 CS20 Timer/Counter2 (8 Bits) Timer/Counter2 Output Compare Register 114 116 116 UBRR[11:8] 117 43 152 UCSRC URSEL UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL 150 0x1F (0x3F) EEARH - - - - - - - EEAR8 20 0x1E (0x3E) EEARL EEAR7 EEAR6 EEAR5 EEAR4 EEAR3 EEAR2 EEAR1 EEAR0 20 0x1D (0x3D) EEDR 0x1C (0x3C) EECR 0x1B (0x3B) Reserved 0x1A (0x3A) Reserved 0x19 (0x39) Reserved 0x18 (0x38) 0x17 (0x37) EEPROM Data Register 20 - - - - EERIE EEMWE EEWE EERE 20 PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 65 DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 65 0x16 (0x36) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 65 0x15 (0x35) PORTC - PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 65 0x14 (0x34) DDRC - DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 65 0x13 (0x33) PINC - PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 65 0x12 (0x32) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 65 0x11 (0x31) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 65 0x10 (0x30) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 0x0F (0x2F) SPDR SPI Data Register 65 127 0x0E (0x2E) SPSR SPIF WCOL - - - - - SPI2X 126 0x0D (0x2D) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 125 0x0C (0x2C) UDR 0x0B (0x2B) UCSRA RXC TXC UDRE FE DOR PE U2X MPCM 148 0x0A (0x2A) UCSRB RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 149 0x09 (0x29) UBRRL 0x08 (0x28) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 186 0x07 (0x27) ADMUX REFS1 REFS0 ADLAR - MUX3 MUX2 MUX1 MUX0 199 0x06 (0x26) ADCSRA ADEN ADSC ADFR ADIF ADIE ADPS2 ADPS1 ADPS0 200 0x05 (0x25) ADCH ADC Data Register High byte 201 0x04 (0x24) ADCL ADC Data Register Low byte 201 0x03 (0x23) TWDR 0x02 (0x22) TWAR USART I/O Data Register 148 USART Baud Rate Register Low byte 152 Two-wire Serial Interface Data Register TWA6 TWA5 TWA4 TWA3 TWA2 167 TWA1 TWA0 TWGCE 167 8 2486ZS-AVR-02/11 ATmega8(L) Register Summary (Continued) Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x01 (0x21) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 - TWPS1 TWPS0 166 0x00 (0x20) TWBR Notes: Two-wire Serial Interface Bit Rate Register 165 1. Refer to the USART description ("USART" on page 129) for details on how to access UBRRH and UCSRC ("Accessing UBRRH/UCSRC Registers" on page 146) 2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written 3. Some of the Status Flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only 9 2486ZS-AVR-02/11 ATmega8(L) Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd Rd + Rr Z, C, N, V, H ADC Rd, Rr Add with Carry two Registers Rd Rd + Rr + C Z, C, N, V, H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl Rdh:Rdl + K Z, C, N, V, S 2 SUB Rd, Rr Subtract two Registers Rd Rd - Rr Z, C, N, V, H 1 SUBI Rd, K Subtract Constant from Register Rd Rd - K Z, C, N, V, H 1 SBC Rd, Rr Subtract with Carry two Registers Rd Rd - Rr - C Z, C, N, V, H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd Rd - K - C Z, C, N ,V, H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl Rdh:Rdl - K Z, C, N, V, S 2 AND Rd, Rr Logical AND Registers Rd Rd * Rr Z, N, V 1 1 1 ANDI Rd, K Logical AND Register and Constant Rd Rd * K Z, N, V OR Rd, Rr Logical OR Registers Rd Rd v Rr Z, N, V 1 ORI Rd, K Logical OR Register and Constant Rd Rd v K Z, N, V 1 EOR Rd, Rr Exclusive OR Registers Rd Rd Rr Z, N, V 1 COM Rd One's Complement Rd 0xFF - Rd Z, C, N, V 1 NEG Rd Two's Complement Rd 0x00 - Rd Z, C, N, V, H 1 SBR Rd,K Set Bit(s) in Register Rd Rd v K Z, N, V 1 CBR Rd,K Clear Bit(s) in Register Rd Rd * (0xFF - K) Z, N, V 1 INC Rd Increment Rd Rd + 1 Z, N, V 1 DEC Rd Decrement Rd Rd - 1 Z, N, V 1 TST Rd Test for Zero or Minus Rd Rd * Rd Z, N, V 1 CLR Rd Clear Register Rd Rd Rd Z, N, V 1 SER Rd Set Register Rd 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 Rd x Rr Z, C 2 MULS Rd, Rr Multiply Signed R1:R0 Rd x Rr Z, C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 Rd x Rr Z, C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 (Rd x Rr) << Z, C 2 FMULS Rd, Rr Fractional Multiply Signed Z, C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned 1 R1:R0 (Rd x Rr) << 1 R1:R0 (Rd x Rr) << 1 Z, C 2 Relative Jump PC PC + k + 1 None 2 Indirect Jump to (Z) PC Z None 2 BRANCH INSTRUCTIONS RJMP k IJMP Relative Subroutine Call PC PC + k + 1 None 3 ICALL Indirect Call to (Z) PC Z None 3 RET Subroutine Return PC STACK None 4 RETI Interrupt Return PC STACK I if (Rd = Rr) PC PC + 2 or 3 None RCALL k 4 CPSE Rd,Rr Compare, Skip if Equal CP Rd,Rr Compare Rd - Rr Z, N, V, C, H 1 CPC Rd,Rr Compare with Carry Rd - Rr - C Z, N, V, C, H 1 CPI Rd,K Compare Register with Immediate Rd - K Z, N, V, C, H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC PC + 2 or 3 None 1/2/3 1 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC PC + 2 or 3 None 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC PC + 2 or 3 None 1/2/3 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PCPC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PCPC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N V= 0) then PC PC + k + 1 None 1/2 BRLT k Branch if Less Than Zero, Signed if (N V= 1) then PC PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC PC + k + 1 None 1/2 10 2486ZS-AVR-02/11 ATmega8(L) Instruction Set Summary (Continued) Mnemonics Operands Description Operation Flags #Clocks BRIE k Branch if Interrupt Enabled if ( I = 1) then PC PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC PC + k + 1 None 1/2 None 1 None 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers MOVW Rd, Rr Copy Register Word Rd Rr Rd+1:Rd Rr+1:Rr LDI Rd, K Load Immediate Rd K None 1 LD Rd, X Load Indirect Rd (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd (X), X X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X X - 1, Rd (X) None 2 2 LD Rd, Y Load Indirect Rd (Y) None LD Rd, Y+ Load Indirect and Post-Inc. Rd (Y), Y Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y Y - 1, Rd (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd (Y + q) None 2 LD Rd, Z Load Indirect Rd (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd (Z), Z Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z Z - 1, Rd (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd (Z + q) None 2 2 LDS Rd, k Load Direct from SRAM Rd (k) None ST X, Rr Store Indirect (X) Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) Rr, X X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X X - 1, (X) Rr None 2 ST Y, Rr Store Indirect (Y) Rr None 2 ST Y+, Rr Store Indirect and Post-Inc. (Y) Rr, Y Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y Y - 1, (Y) Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) Rr None 2 ST Z, Rr Store Indirect (Z) Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) Rr, Z Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z Z - 1, (Z) Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) Rr None 2 STS k, Rr Store Direct to SRAM (k) Rr None 2 Load Program Memory R0 (Z) None 3 LPM LPM Rd, Z Load Program Memory Rd (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd (Z), Z Z+1 None 3 Store Program Memory (Z) R1:R0 None - In Port Rd P None 1 SPM IN Rd, P OUT P, Rr Out Port P Rr None 1 PUSH Rr Push Register on Stack STACK Rr None 2 POP Rd Pop Register from Stack Rd STACK None 2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) 0 None 2 LSL Rd Logical Shift Left Rd(n+1) Rd(n), Rd(0) 0 Z, C, N, V 1 LSR Rd Logical Shift Right Rd(n) Rd(n+1), Rd(7) 0 Z, C, N, V 1 ROL Rd Rotate Left Through Carry Rd(0)C,Rd(n+1) Rd(n),CRd(7) Z, C, N, V 1 ROR Rd Rotate Right Through Carry Rd(7)C,Rd(n) Rd(n+1),CRd(0) Z, C, N, V 1 ASR Rd Arithmetic Shift Right Rd(n) Rd(n+1), n=0..6 Z, C, N, V 1 SWAP Rd Swap Nibbles Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) None 1 BSET s Flag Set SREG(s) 1 SREG(s) 1 BCLR s Flag Clear SREG(s) 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) T None 1 1 SEC Set Carry C1 C CLC Clear Carry C0 C 1 SEN Set Negative Flag N1 N 1 CLN Clear Negative Flag N0 N 1 SEZ Set Zero Flag Z1 Z 1 CLZ Clear Zero Flag Z0 Z 1 SEI Global Interrupt Enable I1 I 1 CLI Global Interrupt Disable I0 I 1 1 SES Set Signed Test Flag S1 S CLS Clear Signed Test Flag S0 S 1 SEV Set Twos Complement Overflow. V1 V 1 CLV Clear Twos Complement Overflow V0 V 1 SET Set T in SREG T1 T 1 11 2486ZS-AVR-02/11 ATmega8(L) Instruction Set Summary (Continued) Mnemonics Operands Description Operation Flags #Clocks CLT Clear T in SREG T0 T 1 SEH CLH Set Half Carry Flag in SREG Clear Half Carry Flag in SREG H1 H0 H H 1 1 MCU CONTROL INSTRUCTIONS NOP SLEEP No Operation Sleep (see specific descr. for Sleep function) None None 1 1 12 2486ZS-AVR-02/11 ATmega8(L) Ordering Information Speed (MHz) 8 16 Notes: Ordering Code(2) Package(1) 2.7 - 5.5 ATmega8L-8AU ATmega8L-8AUR(3) ATmega8L-8PU ATmega8L-8MU ATmega8L-8MUR(3) 32A 32A 28P3 32M1-A 32M1-A 4.5 - 5.5 ATmega8-16AU ATmega8-16AUR(3) ATmega8-16PU ATmega8-16MU ATmega8-16MUR(3) 32A 32A 28P3 32M1-A 32M1-A Power Supply (V) Operation Range Industrial (-40C to 85C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green 3. Tape & Reel Package Type 32A 32-lead, Thin (1.0mm) Plastic Quad Flat Package (TQFP) 28P3 28-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 13 2486ZS-AVR-02/11 ATmega8(L) Packaging Information 32A PIN 1 IDENTIFIER PIN 1 e B E1 E D1 D C 0~7 A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation ABA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. SYMBOL MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 8.75 9.00 9.25 D1 6.90 7.00 7.10 E 8.75 9.00 9.25 E1 6.90 7.00 7.10 B 0.30 - 0.45 C 0.09 - 0.20 L 0.45 - 0.75 e NOTE Note 2 Note 2 0.80 TYP 2010-10-20 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. REV. 32A C 14 2486ZS-AVR-02/11 ATmega8(L) 28P3 D PIN 1 E1 A SEATING PLANE L B2 B1 A1 B (4 PLACES) 0 ~ 15 REF e E C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL eB Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). A MIN - NOM MAX - 4.5724 A1 0.508 - - D 34.544 - 34.798 E 7.620 - 8.255 E1 7.112 - 7.493 B 0.381 - 0.533 B1 1.143 - 1.397 B2 0.762 - 1.143 L 3.175 - 3.429 C 0.203 - 0.356 eB - - 10.160 e NOTE Note 1 Note 1 2.540 TYP 09/28/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 28P3 REV. B 15 2486ZS-AVR-02/11 ATmega8(L) 32M1-A D D1 1 2 3 0 Pin 1 ID E1 SIDE VIEW E TOP VIEW A3 A2 A1 A K 0.08 C P D2 1 2 3 P Pin #1 Notch (0.20 R) K e SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 - 0.02 0.05 A2 - 0.65 1.00 A3 E2 b COMMON DIMENSIONS (Unit of Measure = mm) L BOTTOM VIEW 0.20 REF b 0.18 0.23 0.30 D 4.90 5.00 5.10 D1 4.70 4.75 4.80 D2 2.95 3.10 3.25 E 4.90 5.00 5.10 E1 4.70 4.75 4.80 E2 2.95 3.10 3.25 e Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2. NOTE 0.50 BSC L 0.30 0.40 0.50 0.60 12o P - - 0 - - K 0.20 - - 5/25/06 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm, 3.10 mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 32M1-A REV. E 16 2486ZS-AVR-02/11 ATmega8(L) Errata The revision letter in this section refers to the revision of the ATmega8 device. ATmega8 Rev. D to I, M * * * * First Analog Comparator conversion may be delayed Interrupts may be lost when writing the timer registers in the asynchronous timer Signature may be Erased in Serial Programming Mode CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when 32KHz Oscillator is Used to Clock the Asynchronous Timer/Counter2 * Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request 1. First Analog Comparator conversion may be delayed If the device is powered by a slow rising VCC, the first Analog Comparator conversion will take longer than expected on some devices. Problem Fix / Workaround When the device has been powered or reset, disable then enable theAnalog Comparator before the first conversion. 2. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronized to the asynchronous timer clock is written when the asynchronous Timer/Counter register(TCNTx) is 0x00. Problem Fix / Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register(TCCRx), asynchronous Timer Counter Register(TCNTx), or asynchronous Output Compare Register(OCRx). 3. Signature may be Erased in Serial Programming Mode If the signature bytes are read before a chiperase command is completed, the signature may be erased causing the device ID and calibration bytes to disappear. This is critical, especially, if the part is running on internal RC oscillator. Problem Fix / Workaround: Ensure that the chiperase command has exceeded before applying the next command. 4. CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when 32KHz Oscillator is Used to Clock the Asynchronous Timer/Counter2 When the internal RC Oscillator is used as the main clock source, it is possible to run the Timer/Counter2 asynchronously by connecting a 32KHz Oscillator between XTAL1/TOSC1 and XTAL2/TOSC2. But when the internal RC Oscillator is selected as the main clock source, the CKOPT Fuse does not control the internal capacitors on XTAL1/TOSC1 and XTAL2/TOSC2. As long as there are no capacitors connected to XTAL1/TOSC1 and XTAL2/TOSC2, safe operation of the Oscillator is not guaranteed. Problem Fix / Workaround Use external capacitors in the range of 20pF - 36pF on XTAL1/TOSC1 and XTAL2/TOSC2. This will be fixed in ATmega8 Rev. G where the CKOPT Fuse will control internal capacitors also when internal RC Oscillator is selected as main clock source. For ATmega8 Rev. G, CKOPT = 0 (programmed) will enable the internal capacitors on XTAL1 and XTAL2. Customers who want compatibility between Rev. G and older revisions, must ensure that CKOPT is unprogrammed (CKOPT = 1). 17 2486ZS-AVR-02/11 ATmega8(L) 5. Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request. Reading EEPROM by using the ST or STS command to set the EERE bit in the EECR register triggers an unexpected EEPROM interrupt request. Problem Fix / Workaround Always use OUT or SBI to set EERE in EECR. 18 2486ZS-AVR-02/11 ATmega8(L) Datasheet Revision History Please note that the referring page numbers in this section are referred to this document. The referring revision in this section are referring to the document revision. Changes from Rev. 1. Updated the datasheet according to the Atmel new Brand Style Guide. 2486Y- 10/10 to 2. Updated "Ordering Information" on page 13. Added Ording Information for Rev. 2486Z- 02/11 "Tape&Reel" devices Changes from Rev. 1. Max Rise/Fall time in Table 102 on page 239 has been corrected from 1.6ns to 1600ns. 2486X- 06/10 to Rev. 2486Y- 10/10 2. Note is added to "Performing Page Erase by SPM" on page 209. 3. Updated/corrected several short-cuts and added some new ones. 4. Updated last page according to new standard. Changes from Rev. 1. Updated "DC Characteristics" on page 235 with new VOL maximum value (0.9V and 0.6V). 2486W- 02/10 to Rev. 2486X- 06/10 Changes from Rev. 1. Updated "ADC Characteristics" on page 241 with VINT maximum value (2.9V). 2486V- 05/09 to Rev. 2486W- 02/10 Changes from Rev. 1. Updated "Errata" on page 289. 2486U- 08/08 to 2. Updated the last page with Atmel's new adresses. Rev. 2486V- 05/09 Changes from Rev. 1. 2486T- 05/08 to Rev. 2486U- 08/08 Updated "DC Characteristics" on page 235 with ICC typical values. Changes from Rev. 1. Updated Table 98 on page 233. 2486S- 08/07 to 2. Updated "Ordering Information" on page 285. Rev. 2486T- 05/08 - Commercial Ordering Code removed. - No Pb-free packaging option removed. 19 2486ZS-AVR-02/11 ATmega8(L) Changes from Rev. 1. Updated "Features" on page 1. 2486R- 07/07 to Rev. 2486S- 08/07 2. Added "Data Retention" on page 7. 3. Updated "Errata" on page 289. 4. Updated "Slave Mode" on page 125. Changes from Rev. 1. Added text to Table 81 on page 211. 2486Q- 10/06 to Rev. 2486R- 07/07 2. Fixed typo in "Peripheral Features" on page 1. 3. Updated Table 16 on page 42. 4. Updated Table 75 on page 199. 5. Removed redundancy and updated typo in Notes section of "DC Characteristics" on page 235. Changes from Rev. 1. Updated "Timer/Counter Oscillator" on page 32. 2486P- 02/06 to Rev. 2486Q- 10/06 2. Updated "Fast PWM Mode" on page 88. 3. Updated code example in "USART Initialization" on page 134. 4. Updated Table 37 on page 96, Table 39 on page 97, Table 42 on page 115, Table 44 on page 115, and Table 98 on page 233. 5. Updated "Errata" on page 289. Changes from Rev. 1. Added "Resources" on page 7. 2486O-10/04 to Rev. 2486P- 02/06 2. Updated "External Clock" on page 32. 3. Updated "Serial Peripheral Interface - SPI" on page 121. 4. Updated Code Example in "USART Initialization" on page 134. 5. Updated Note in "Bit Rate Generator Unit" on page 164. 6. Updated Table 98 on page 233. 7. Updated Note in Table 103 on page 241. 8. Updated "Errata" on page 289. Changes from Rev. 1. Removed to instances of "analog ground". Replaced by "ground". 2486N-09/04 to 2. Updated Table 7 on page 29, Table 15 on page 38, and Table 100 on page 237. Rev. 2486O-10/04 3. Updated "Calibrated Internal RC Oscillator" on page 30 with the 1 MHz default value. 20 2486ZS-AVR-02/11 ATmega8(L) 4. Table 89 on page 218 and Table 90 on page 218 moved to new section "Page Size" on page 218. 5. Updated descripton for bit 4 in "Store Program Memory Control Register - SPMCR" on page 206. 6. Updated "Ordering Information" on page 285. Changes from Rev. 1. Added note to MLF package in "Pin Configurations" on page 2. 2486M-12/03 to 2. Updated "Internal Voltage Reference Characteristics" on page 42. Rev. 2486N-09/04 3. Updated "DC Characteristics" on page 235. 4. ADC4 and ADC5 support 10-bit accuracy. Document updated to reflect this. Updated features in "Analog-to-Digital Converter" on page 189. Updated "ADC Characteristics" on page 241. 5. Removed reference to "External RC Oscillator application note" from "External RC Oscillator" on page 28. Changes from Rev. 1. Updated "Calibrated Internal RC Oscillator" on page 30. 2486L-10/03 to Rev. 2486M-12/03 Changes from Rev. 1. Removed "Preliminary" and TBDs from the datasheet. 2486K-08/03 to 2. Renamed ICP to ICP1 in the datasheet. Rev. 2486L-10/03 3. Removed instructions CALL and JMP from the datasheet. 4. Updated tRST in Table 15 on page 38, VBG in Table 16 on page 42, Table 100 on page 237 and Table 102 on page 239. 5. Replaced text "XTAL1 and XTAL2 should be left unconnected (NC)" after Table 9 in "Calibrated Internal RC Oscillator" on page 30. Added text regarding XTAL1/XTAL2 and CKOPT Fuse in "Timer/Counter Oscillator" on page 32. 6. Updated Watchdog Timer code examples in "Timed Sequences for Changing the Configuration of the Watchdog Timer" on page 45. 7. Removed bit 4, ADHSM, from "Special Function IO Register - SFIOR" on page 58. 8. Added note 2 to Figure 103 on page 208. 9. Updated item 4 in the "Serial Programming Algorithm" on page 231. 10. Added tWD_FUSE to Table 97 on page 232 and updated Read Calibration Byte, Byte 3, in Table 98 on page 233. 11. Updated Absolute Maximum Ratings* and DC Characteristics in "Electrical Characteristics" on page 235. 21 2486ZS-AVR-02/11 ATmega8(L) Changes from Rev. 1. Updated VBOT values in Table 15 on page 38. 2486J-02/03 to 2. Updated "ADC Characteristics" on page 241. Rev. 2486K-08/03 3. Updated "ATmega8 Typical Characteristics" on page 242. 4. Updated "Errata" on page 289. Changes from Rev. 1. Improved the description of "Asynchronous Timer Clock - clkASY" on page 26. 2486I-12/02 to Rev. 2. Removed reference to the "Multipurpose Oscillator" application note and the "32 kHz 2486J-02/03 Crystal Oscillator" application note, which do not exist. 3. Corrected OCn waveforms in Figure 38 on page 89. 4. Various minor Timer 1 corrections. 5. Various minor TWI corrections. 6. Added note under "Filling the Temporary Buffer (Page Loading)" on page 209 about writing to the EEPROM during an SPM Page load. 7. Removed ADHSM completely. 8. Added section "EEPROM Write during Power-down Sleep Mode" on page 23. 9. Removed XTAL1 and XTAL2 description on page 5 because they were already described as part of "Port B (PB7..PB0) XTAL1/XTAL2/TOSC1/TOSC2" on page 5. 10. Improved the table under "SPI Timing Characteristics" on page 239 and removed the table under "SPI Serial Programming Characteristics" on page 234. 11. Corrected PC6 in "Alternate Functions of Port C" on page 61. 12. Corrected PB6 and PB7 in "Alternate Functions of Port B" on page 58. 13. Corrected 230.4 Mbps to 230.4 kbps under "Examples of Baud Rate Setting" on page 153. 14. Added information about PWM symmetry for Timer 2 in "Phase Correct PWM Mode" on page 111. 15. Added thick lines around accessible registers in Figure 76 on page 163. 16. Changed "will be ignored" to "must be written to zero" for unused Z-pointer bits under "Performing a Page Write" on page 209. 17. Added note for RSTDISBL Fuse in Table 87 on page 216. 18. Updated drawings in "Packaging Information" on page 286. 22 2486ZS-AVR-02/11 ATmega8(L) Changes from Rev. 1. Added errata for Rev D, E, and F on page 289. 2486H-09/02 to Rev. 2486I-12/02 Changes from Rev. 1. Changed the Endurance on the Flash to 10,000 Write/Erase Cycles. 2486G-09/02 to Rev. 2486H-09/02 Changes from Rev. 1. Updated Table 103, "ADC Characteristics," on page 241. 2486F-07/02 to Rev. 2486G-09/02 Changes from Rev. 1. Changes in "Digital Input Enable and Sleep Modes" on page 55. 2486E-06/02 to 2. Addition of OCS2 in "MOSI/OC2 - Port B, Bit 3" on page 59. Rev. 2486F-07/02 3. The following tables have been updated: Table 51, "CPOL and CPHA Functionality," on page 127, Table 59, "UCPOL Bit Settings," on page 152, Table 72, "Analog Comparator Multiplexed Input(1)," on page 188, Table 73, "ADC Conversion Time," on page 193, Table 75, "Input Channel Selections," on page 199, and Table 84, "Explanation of Different Variables used in Figure 103 on page 208 and the Mapping to the Z-pointer," on page 214. 4. Changes in "Reading the Calibration Byte" on page 227. 5. Corrected Errors in Cross References. Changes from Rev. 1. Updated Some Preliminary Test Limits and Characterization Data 2486D-03/02 to The following tables have been updated: Rev. 2486E-06/02 Table 15, "Reset Characteristics," on page 38, Table 16, "Internal Voltage Reference Characteristics," on page 42, DC Characteristics on page 235, Table , "ADC Characteristics," on page 241. 2. Changes in External Clock Frequency Added the description at the end of "External Clock" on page 32. Added period changing data in Table 99, "External Clock Drive," on page 237. 3. Updated TWI Chapter More details regarding use of the TWI bit rate prescaler and a Table 65, "TWI Bit Rate Prescaler," on page 167. Changes from Rev. 1. Updated Typical Start-up Times. 2486C-03/02 to The following tables has been updated: Rev. 2486D-03/02 Table 5, "Start-up Times for the Crystal Oscillator Clock Selection," on page 28, Table 6, "Start-up Times for the Low-frequency Crystal Oscillator Clock Selection," on page 28, Table 8, "Start-up Times for the External RC Oscillator Clock Selection," on page 29, and Table 12, "Start-up Times for the External Clock Selection," on page 32. 2. Added "ATmega8 Typical Characteristics" on page 242. 23 2486ZS-AVR-02/11 Changes from Rev. 1. Updated TWI Chapter. 2486B-12/01 to More details regarding use of the TWI Power-down operation and using the TWI as Master with low TWBRR values are added into the datasheet. Rev. 2486C-03/02 Added the note at the end of the "Bit Rate Generator Unit" on page 164. Added the description at the end of "Address Match Unit" on page 164. 2. Updated Description of OSCCAL Calibration Byte. In the datasheet, it was not explained how to take advantage of the calibration bytes for 2, 4, and 8 MHz Oscillator selections. This is now added in the following sections: Improved description of "Oscillator Calibration Register - OSCCAL" on page 31 and "Calibration Byte" on page 218. 3. Added Some Preliminary Test Limits and Characterization Data. Removed some of the TBD's in the following tables and pages: Table 3 on page 26, Table 15 on page 38, Table 16 on page 42, Table 17 on page 44, "TA = -40C to +85C, VCC = 2.7V to 5.5V (unless otherwise noted)" on page 235, Table 99 on page 237, and Table 102 on page 239. 4. Updated Programming Figures. Figure 104 on page 219 and Figure 112 on page 230 are updated to also reflect that AVCC must be connected during Programming mode. 5. Added a Description on how to Enter Parallel Programming Mode if RESET Pin is Disabled or if External Oscillators are Selected. Added a note in section "Enter Programming Mode" on page 221. Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1)(408) 441-0311 Fax: (+1)(408) 487-2600 www.atmel.com Atmel Asia Limited Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81)(3) 3523-3551 Fax: (+81)(3) 3523-7581 (c) 2011 Atmel Corporation. All rights reserved. / Rev. CORP0XXXX Atmel (R), Atmel logo and combinations thereof, AVR (R) and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2486ZS-AVR-02/11