LM2757
VIN
C2+
C2-
1 µF
0.47 µF
VOUT
1 µF
C1+
C1-
0.47 µF
*Bump D1 is No Connect (NC)
VIN = 3 V - 5.5 V
B2,B3
A3
B1
A1
C3
C1,C2
A2
GND
VOUT = 4.1 V (100 mA), 4.5 V (110 mA)
5 V (180 mA)
M0 D3
M1 D2
COUT
C2
C1
CIN
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
LM2757 Switched-Capacitor Boost Regulator With High Impedance Output in Shutdown
1 Features 3 Description
The LM2757 is a constant-frequency pre-regulated
1 Dual Gain Converter (2×, 3/2×) With up to 93% switched-capacitor charge pump that operates at
Efficiency 1.25 MHz to produce a low-noise regulated output
Inductorless Solution Uses Only 4 Small Ceramic voltage. The device can be configured to provide up
Capacitors to 100 mA at 4.1 V, 110 mA at 4.5 V, or 180 mA at 5
Total Solution Area < 12 mm2V. Excellent efficiency is achieved without the use of
an inductor by operating the charge pump in a gain of
True Input-Output and Output-Input Disconnect either 3/2 or 2 according to the input voltage and
Up to 180-mA Output Current Capability (5 V) output voltage option selection.
Selectable 4.1-V, 4.5-V or 5-V Output The LM2757 presents a high impedance at the VOUT
Pre-Regulation Minimizes Input Current Ripple pin when shut down. This allows for use in
1.24-MHz Switching Frequency for Low-Noise, applications that require the regulated output bus to
Low-Ripple Output Voltage be driven by another supply while the LM2757 is shut
down.
Integrated Overcurrent and Thermal Shutdown
Protection The LM2757 device comes in a tiny 12-pin 0.4-mm
pitch DSBGA package. A perfect fit for space-
2 Applications constrained, battery-operated applications, the device
requires only 4 small, inexpensive ceramic
USB/USB-OTG/HDMI Power capacitors. Built-in soft-start, overcurrent protection,
Supercapacitor Charger and thermal shutdown features are also included in
this device.
Keypad LED Drive
Audio Amplifier Power Supply Device Information(1)
Low-Current Camera Flash PART NUMBER PACKAGE BODY SIZE (MAX)
General Purpose Li-Ion-to-5-V Conversion LM2757 DSBGA (12) 1.641 mm × 1.581 mm
Cellular Phone SIM Cards (1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
Table of Contents
8.4 Device Functional Modes........................................ 11
1 Features.................................................................. 19 Application and Implementation ........................ 13
2 Applications ........................................................... 19.1 Application Information............................................ 13
3 Description............................................................. 19.2 Typical Application ................................................. 13
4 Revision History..................................................... 210 Power Supply Recommendations ..................... 18
5 Device Options....................................................... 311 Layout................................................................... 19
6 Pin Configuration and Functions......................... 311.1 Layout Guidelines ................................................. 19
7 Specifications......................................................... 411.2 Layout Example .................................................... 19
7.1 Absolute Maximum Ratings ...................................... 412 Device and Documentation Support................. 20
7.2 ESD Ratings.............................................................. 412.1 Device Support .................................................... 20
7.3 Recommended Operating Conditions....................... 412.2 Documentation Support ........................................ 20
7.4 Thermal Information.................................................. 412.3 Community Resources.......................................... 20
7.5 Electrical Characteristics........................................... 512.4 Trademarks........................................................... 20
7.6 Typical Characteristics.............................................. 612.5 Electrostatic Discharge Caution............................ 20
8 Detailed Description............................................ 10 12.6 Glossary................................................................ 20
8.1 Overview................................................................. 10 13 Mechanical, Packaging, and Orderable
8.2 Functional Block Diagram....................................... 10 Information ........................................................... 21
8.3 Feature Description................................................. 10
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (May 2013) to Revision F Page
Added Device Information and Pin Configuration and Functions sections, ESD Rating table, Feature Description,
Device Functional Modes,Application and Implementation,Power Supply Recommendations,Layout,Device and
Documentation Support , and Mechanical, Packaging, and Orderable Information sections................................................ 1
Changes from Revision D (May 2013) to Revision E Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 18
2Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
A3
B3
C3
D3
A2
B2
C2
D2
A1
B1
C1
D1
A1
B1
C1
D1
A2
B2
C2
D2
A3
B3
C3
D3
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
5 Device Options
Table 1. Mode Selection Definition
M0 M1 OUTPUT VOLTAGE MODE
0 0 Device shutdown, output high impedance
0 1 5 V
1 0 4.5 V
1 1 4.1 V
6 Pin Configuration and Functions
YFQ Package
12-Pin DSBGA
Top View (left); Bottom View (right)
Pin Functions
PIN TYPE DESCRIPTION
NUMBER NAME
A1 C2+ Power Flying Capacitor C2 Connection
A2 VOUT Power Regulated Output Voltage
A3 C1+ Power Flying Capacitor C1 Connection
B1 C1Power Flying Capacitor C1 Connection
B2 VIN Power Input Voltage Connection
B3 VIN Power Input Voltage Connection
C1 GND Ground Ground Connection
C2 GND Ground Ground Connection
C3 C2Ground Flying Capacitor C2 Connection
D1 NC NC No Connect Do not connect this pin to any node, voltage or GND. Must be left floating.
D2 M1 Logic input Mode select pin 1
D3 M0 Logic input Mode select pin 0
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN MAX UNIT
VIN pin: voltage to GND –0.3 6 V
M0, M1 pins: voltage to GND –0.3 6 V
Continuous power dissipation(4) Internally Limited
Junction temperature, TJ-MAX 150 °C
Maximum lead temperature (soldering, 10 sec.) 265 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
(3) All voltages are with respect to the potential at the GND pins.
(4) Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ= 145°C (typical) and
disengages at TJ= 135°C (typical).
7.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2500 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)(1)(2)
MIN NOM MAX UNIT
Input voltage 2.7 5.5 °C
Junction temperature, TJ–30 110 °C
Ambient temperature, TA(3) –30 85 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the potential at the GND pins.
(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJMAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP (RθJA × PD-MAX).
7.4 Thermal Information LM2757
THERMAL METRIC(1) YFQ (DSBGA) UNIT
12 PINS
RθJA Junction-to-ambient thermal resistance 75 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
7.5 Electrical Characteristics
Unless otherwise specified, typical (TYP) limits in apply for TA= 25ºC; minimium (MIN) and maximum (MAX) limits apply over
the full operating ambient temperature range (–30°C TA+85°C) . Unless otherwise noted, specifications apply to Typical
Application with: VIN = 3.6 V, V(M0) = 0 V, V(M1) = VIN, CIN = C2= 0.47 µF, CIN= COUT = 1 µF.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
3.2 V VIN 5.5 V
–30°C TA+60°C 4.870 5.130
5
IOUT = 0 to 180 mA (2.6%) (2.6%)
V(M0) = 0V, V(M1) = VIN
3. V VIN 5.5 V
–30°C TA+85°C 4.865 5.130
5
IOUT = 0 to 150 mA (2.7%) (2.6%)
VOUT Output voltage V
V(M0) = 0V, V(M1) = VIN
3 V VIN 5.5 V 4.406 4.613
IOUT = 0 to 110 mA 4.5
(–2.1%) (2.5%)
V(M0) = VIN, V(M1) = 0 V
3. V VIN 5.5 V 3.985 4.223
IOUT = 0 to 100 mA 4.1
(–2.8%) (3%)
V(M0) = VIN, V(M1) = VIN
V(M0) = 0 V, V(M1) = VIN (5 V)
IOUT = 0 mA 2.4 2.79
VIN = 3.6 V
V(M0) = VIN, V(M1) = 0 V (4.5 V)
IQQuiescent supply current IOUT = 0 mA 1.5 1.80 mA
VIN = 3.6 V
V(M0) = VIN, V(M1) = VIN (4.1 V)
IOUT = 0 mA 1.3 1.65
VIN = 3.6 V
V(M0) = 0 V, V(M1) = 0 V
ISD Shutdown supply current 1.1 2 µA
VIN = 3.6 V
IOUT = 150 mA
VROutput ivoltage rpple V(M0) = 0V, V(M1) = VIN (5 V) 20 mVp–p
3 V VIN 5.5 V 0.932 1.552
ƒSW Switching frequency 3 V VIN 5.5 V 1.242 MHz
(–25%) (+25%)
Input pins: M1, M0
VIN Logic input high 1 VIN V
3 V VIN 5.5 V
Input pins: M1, M0
VIL Logic input low 0 0.40 V
3 V VIN 5.5 V
Logic input pulldown
RPULLDOWN V(M1, M0) = 5.5 V 324 457 k
resistance (M0, M1) Input Pins: M1, M0
IIH Logic input high current 5 µA
V(M1, M0) = 1.8 V(4)
Input Pins: M1, M0
IIL Logic input low current 10 nA
V(M1, M0) = 0 V
1.5× to 2×, V(M0) = VIN, V(M1) = 0 V 3.333 V
to 1.5×, V(M0) = VIN, V(M1) = 0 V 3.413 V
Hysteresis, V(M0) = VIN, V(M1) = 0 V 80 mV
VGGain transition voltage 1.5× to 2×, V(M0) = 0 V, V(M1) = VIN 3.87 V
to 1.5×, V(M0) = 0 V, V(M1) = VIN 3.93 V
Hysteresis, V(M0) = 0 V, V(M1) = VIN 60 mV
ISC Short-circuit output current VOUT = 0 V 250 mA
VOUT turnon time from
ION 300 µs
shutdown (5)
(1) All voltages are with respect to the potential at the GND pins.
(2) Minimum and maximum limits are specified by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm.
(3) CIN, COUT, C1, C2: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.
(4) There is a 450-k(typical) pulldown resistor connected internally to each logic input.
(5) Turnon time is measured from when the M0 or M1 signal is pulled high until the output voltage crosses 90% of its final value.
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
7.6 Typical Characteristics
Unless otherwise specified: VIN = 3.6 V, V(M0) = 0 V, V(M1) = VIN, C1= C2= 0.47 µF, CIN = COUT = 1 µF, TA= 25°C.
Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's).
5-V Mode 4.5-V Mode
Figure 1. Efficiency vs. Input Voltage Figure 2. Efficiency vs. Input Voltage
4.1-V Mode 5-V Mode
Figure 3. Efficiency vs. Input Voltage Figure 4. Output Voltage vs. Output Current
4.5-V Mode 4.1-V Mode
Figure 5. Output Voltage vs. Output Current Figure 6. Output Voltage vs. Output Current
6Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
Typical Characteristics (continued)
Unless otherwise specified: VIN = 3.6 V, V(M0) = 0 V, V(M1) = VIN, C1= C2= 0.47 µF, CIN = COUT = 1 µF, TA= 25°C.
Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's).
5-V Mode 5-V Mode
Figure 7. Output Voltage Ripple vs. Output Current Figure 8. Output Voltage vs. Input Voltage
4.5-V Mode 4.1-V Mode
Figure 9. Output Voltage vs. Input Voltage Figure 10. Output Voltage vs. Input Voltage
Figure 11. Output Leakage Current, Device Shutdown Figure 12. Output Leakage Current, Device Shutdown
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified: VIN = 3.6 V, V(M0) = 0 V, V(M1) = VIN, C1= C2= 0.47 µF, CIN = COUT = 1 µF, TA= 25°C.
Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's).
Figure 13. Current Limit vs. Input Voltage Figure 14. Oscillator Frequency vs. Input Voltage
Figure 15. Operating Current vs. Input Voltage Figure 16. Shutdown Supply Current vs. Input Voltage
VIN = 3.6 V Load = 200 mA Time scale: 100 µs/Div VOUT = 5-V Mode Load = 200 mA Time scale: 100 µs/Div
CH2: VOUT; Scale: 1V/Div, DC Coupled CH1: VIN; Scale: 1V/Div, DC Coupled
CH4: IIN; Scale: 200 mA/Div, DC Coupled CH2: VOUT; Scale: 100mV/Div, AC Coupled
Figure 17. Start-up Behavior, 5-V Mode Figure 18. Line Step, 3.5 V to 4 V
8Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
Typical Characteristics (continued)
Unless otherwise specified: VIN = 3.6 V, V(M0) = 0 V, V(M1) = VIN, C1= C2= 0.47 µF, CIN = COUT = 1 µF, TA= 25°C.
Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's).
VOUT = 5-V Mode VBATT = 4 V Time scale: 10 µs/Div VOUT = 5-V Mode VBATT = 4 V Time scale: 10 µs/Div
CH1: VOUT; Scale: 50mV/Div, AC Coupled CH1: VOUT; Scale: 50mV/Div, AC Coupled
CH4: IOUT; Scale: 100mA/Div, DC Coupled CH4: IOUT; Scale: 100mA/Div, DC Coupled
Figure 19. Load Step With Li-Ion Battery, 10 mA to 200 mA Figure 20. Load Step With Li-Ion Battery 200 mA to 10 mA
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM2757
SWITCH
CONTROL SWITCH
ARRAY
G = ,
GAIN
CONTROL
2
1.24 V
Ref. Soft-Start
Ramp
OSCILLATOR
EN
3
2
GND
C2-
C2+
C1-
C1+
M0
M1
VOLTAGE MODE
SELECT AND
ENABLE CONTROL
SHORT-
CIRCUIT
PROTECTION
THERMAL
SHUTDOWN
V Ref
VOUT
VIN
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
8 Detailed Description
8.1 Overview
The LM2757 is a switched capacitor converter that produces a regulated output voltage of either 5 V, 4.5 V or
4.1 V, depending on the mode selected. The core of the part is a highly efficient charge pump that utilizes fixed
frequency pre-regulation to minimize ripple and power losses over wide input voltage and output current ranges.
A description of the principal operational characteristics of the LM2757 is shown in the Functional Block Diagram
and detailed in Feature Description.
8.2 Functional Block Diagram
8.3 Feature Description
The core of the LM2757 is a two-phase charge pump controlled by an internally generated non-overlapping
clock. The charge pump operates by using external flying capacitors C1and C2to transfer charge from the input
to the output. At input voltages below 3.9 V (typical) for the 5-V mode, the LM2757 operates in a gain, with
the input current being equal to the load current. At input voltages above 3.9 V (typical) for the 5-V mode, the
part utilizes a gain of 3/2×, resulting in an input current equal to 3/2 times the load current. For the 4.5-V mode,
the LM2757 operates in a gain when the input voltage is below 3.35 V (typical) and transitions to a 3/2× gain
when the input voltage is above 3.35 V (typical). For the 4.1-V mode, the device utilizes the 3/2× gain for the
entire input voltage range.
The two phases of the switched capacitor switching cycle are referred to as the phase one and the phase two.
During phase one, one flying capacitor is charged by the input supply while the other flying capacitor is
connected to the output and delivers charge to the load . After half of the switching cycle [ t = 1/(2 × ƒSW)], the
LM2757 switches to phase two. In this configuration, the capacitor that supplied charge to the load in phase one
is connected to the input to be recharged while the capacitor that had been charged in the previous phase is
connected to the output to deliver charge. With this topology, output ripple is reduced by delivering charge to the
output in every phase.
10 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
Feature Description (continued)
The LM2757 uses fixed frequency pre-regulation to regulate the output voltage. The input and output
connections of the flying capacitors are made with internal MOS switches. Pre-regulation limits the gate drive of
the MOS switch connected between the voltage input and the flying capacitors. Controlling the on resistance of
this switch limits the amount of charge transferred into and out of each flying capacitor during the charge and
discharge phases, and in turn helps to keep the output ripple very low.
8.3.1 Efficiency Performance
Charge-pump efficiency is derived in Equation 1 and Equation 2 (supply current and other losses are neglected
for simplicity):
IIN = G × IOUT (1)
E = (VOUT × IOUT) ÷ (VIN × IIN)=VOUT ÷ (G × VIN)
where
G = the charge pump gain
E = efficiency (2)
Efficiency is at its highest as G × VIN approaches VOUT. Refer to Typical Characteristics for detailed efficiency
data. The transition between gains of 3/2 and 2 are clearly distinguished by the sharp discontinuity in the
efficiency curve.
8.3.2 Soft Start
The LM2757 employs soft-start circuitry to prevent excessive input inrush currents during start-up. At start-up,
the output voltage gradually rises from 0 V to the nominal output voltage. This occurs in 300 µs (typical). Soft-
start is engaged when the device is enabled.
8.3.3 Thermal Shutdown
Protection from damage related to overheating is achieved with a thermal shutdown feature. When the junction
temperature rises to 145°C (typical), the device switches into shutdown mode. The LM2757 disengages thermal
shutdown when the junction temperature of the part is reduced to 135°C (typical). Due to the high efficiency of
the LM2757, thermal shutdown and/or thermal cycling are not encountered when the part is operated within
specified input voltage, output current, and ambient temperature operating ratings. If thermal cycling is seen
under these conditions, the most likely cause is an inadequate PCB layout that does not allow heat to be
sufficiently dissipated out of the device.
8.3.4 Current-Limit Protection
The LM2757 charge pump contains current-limit protection circuitry that protects the device during VOUT fault
conditions where excessive current is drawn. Output current is limited to 250 mA (typical).
8.4 Device Functional Modes
8.4.1 Enable and Voltage Mode Selection
The LM2757 is enabled when either one of the mode select pins (M0, M1) has a logic High voltage applied to it.
There are 450-kpulldown resistors connected internally to each of the mode select pins. The voltage mode is
selected according to Table 1.
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
Device Functional Modes (continued)
8.4.2 Shutdown With Output High Impedance
The LM2757 is in shutdown mode when there is a logic Low voltage on both mode select pins (M0, M1). There
are also 450-kpulldown resistors connected to both mode select pins, pulling the nodes down to ground when
there is no signal present. When in shutdown, the output of the LM2757 is high impedance, allowing an external
supply to drive the output line such as in USB OTG or mobile HDMI applications. Refer to the output leakage
current graphs in Typical Characteristics for typical leakage currents into the VOUT pin, when driven by a
separate supply during shutdown. Output leakage increases with temperature, with the lowest leakage occurring
at –30°C and the highest leakage at 85°C (on which the graph is based). It should be noted when looking at the
graphs as the input voltage falls the leakage peaks at around an input voltage of 1.5 V, then goes down as the
input voltage decrease to 0 V. The leakage at an input voltage of 0 V is the same as the leakage current when
the battery is disconnected from the circuit.
12 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
VIN
C2+
C2-
1 µF
0.47 µF
VOUT
1 µF
C1+
C1-
0.47 µF
*Bump D1 is No Connect (NC)
VIN = 3 V - 5.5 V
B2,B3
A3
B1
A1
C3
C1,C2
A2
GND
VOUT = 4.1 V (100 mA), 4.5 V (110 mA)
5 V (180 mA)
M0 D3
M1 D2
COUT
C2
C1
CIN
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM2757 can create a 4.1-V, 4.5-V or 5-V system rail capable of delivering up to 180 mA of output current to
the load. The 1.242-MHz switched capacitor boost allows for the use of small value discrete external
components.
9.2 Typical Application
9.2.1 Switched-Capacitor Boost Regulator
Figure 21. LM2757 Typical Application
9.2.1.1 Design Requirements
Example requirements for typical switched-capacitor boost regulator applications:
Table 2. Design Parameters
DESIGN PARAMETER EXAMPLE VALUE
Input voltage range 2.7 V to 5.5 V
Output current 0 to 180 mA
Boost switching frequency 1.242 MHz
9.2.1.2 Detailed Design Procedure
9.2.1.2.1 Recommended Capacitor Types
The LM2757 requires 4 external capacitors for proper operation. Surface-mount multi-layer ceramic capacitors
are recommended. These capacitors are small, inexpensive and have very low equivalent series resistance
(ESR, 15 mtypical). Tantalum capacitors, OS-CON capacitors, and aluminum electrolytic capacitors
generally are not recommended for use with the LM2757 due to their high ESR, as compared to ceramic
capacitors.
For most applications, ceramic capacitors with an X7R or X5R temperature characteristic are preferred for use
with the LM2757. These capacitors have tight capacitance tolerance (as good as ±10%) and hold their value over
temperature (X7R: ±15% over –55°C to 125°C; X5R: ±15% over –55°C to 85°C).
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
Capacitors with a Y5V or Z5U temperature characteristic are generally not recommended for use with the
LM2757. These types of capacitors typically have wide capacitance tolerance (80%, –20%) and vary significantly
over temperature (Y5V: +22%, –82% over –30°C to +85°C range; Z5U: 22%, –56% over a 10°C to 85°C range).
Under some conditions, a 1-µF-rated Y5V or Z5U capacitor could have a capacitance as low as 0.1 µF. Such
detrimental deviation is likely to cause Y5V and Z5U capacitors to fail to meet the minimum capacitance
requirements of the LM2757.
Net capacitance of a ceramic capacitor decreases with increased DC bias. This degradation can result in lower
capacitance than expected on the input and/or output, resulting in higher ripple voltages and currents. Using
capacitors at DC bias voltages significantly below the capacitor voltage rating usually minimizes DC bias effects.
Consult capacitor manufacturers for information on capacitor DC bias characteristics.
Capacitance characteristics can vary quite dramatically with different application conditions, capacitor types, and
capacitor manufacturers. It is strongly recommended that the LM2757 circuit be thoroughly evaluated early in the
design-in process with the mass-production capacitors of choice. This helps ensure that any such variability in
capacitance does not negatively impact circuit performance.
The voltage rating of the output capacitor should be 10 V or more. For example, a 10-V 0603 1-µF capacitor is
acceptable for use with the LM2757, as long as the capacitance does not fall below a minimum of 0.5 µF in the
intended application. All other capacitors should have a voltage rating at or above the maximum input voltage of
the application. The capacitors should be selected such that the capacitance on the input does not fall below 0.7
µF, and the capacitance of the flying capacitors does not fall below 0.2 µF.
Table 3 lists some leading ceramic capacitor manufacturers.
Table 3. Manufacturers of Suggested Capacitors
MANUFACTURER CONTACT INFORMATION
AVX www.avx.com
Murata www.murata.com
Taiyo-Yuden www.t-yuden.com
TDK www.component.tdk.com
Vishay-Vitramon www.vishay.com
9.2.1.2.2 Output Capacitor And Output Voltage Ripple
The output capacitor in the LM2757 circuit (COUT) directly impacts the magnitude of output voltage ripple. Other
prominent factors also affecting output voltage ripple include input voltage, output current, and flying capacitance.
Due to the complexity of the regulation topology, providing equations or models to approximate the magnitude of
the ripple can not be easily accomplished. But one important generalization can be made: increasing
(decreasing) the output capacitance results in a proportional decrease (increase) in output voltage ripple.
In typical high-current applications, a 1-µF low-ESR ceramic output capacitor is recommended. Different output
capacitance values can be used to reduce ripple, shrink the solution size, and/or cut the cost of the solution. But
changing the output capacitor may also require changing the flying capacitor and/or input capacitor to maintain
good overall circuit performance. Performance of the LM2757 with different capacitor setups in discussed in
Recommended Capacitance.
High ESR in the output capacitor increases output voltage ripple. If a ceramic capacitor is used at the output, this
is usually not a concern because the ESR of a ceramic capacitor is typically very low and has only a minimal
impact on ripple magnitudes. If a different capacitor type with higher ESR is used (tantalum, for example), the
ESR could result in high ripple. To eliminate this effect, the net output ESR can be significantly reduced by
placing a low-ESR ceramic capacitor in parallel with the primary output capacitor. The low ESR of the ceramic
capacitor is in parallel with the higher ESR, resulting in a low net ESR based on the principles of parallel
resistance reduction.
9.2.1.2.3 Input Capacitor And Input Voltage Ripple
The input capacitor (CIN) is a reservoir of charge that aids a quick transfer of charge from the supply to the flying
capacitors during the charge phase of operation. The input capacitor helps to keep the input voltage from
drooping at the start of the charge phase when the flying capacitors are connected to the input. It also filters
noise on the input pin, keeping this noise out of sensitive internal analog circuitry that is biased off the input line.
14 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
Much like the relationship between the output capacitance and output voltage ripple, input capacitance has a
dominant and first-order effect on input ripple magnitude. Increasing (decreasing) the input capacitance results in
a proportional decrease (increase) in input voltage ripple. Input voltage, output current, and flying capacitance
also affects input ripple levels to some degree.
In typical high-current applications, a 1-µF low-ESR ceramic capacitor is recommended on the input. Different
input capacitance values can be used to reduce ripple, shrink the solution size, and/or cut the cost of the
solution. But changing the input capacitor may also require changing the flying capacitor and/or output capacitor
to maintain good overall circuit performance. Performance of the LM2757 with different capacitor setups is
discussed in Recommended Capacitance.
9.2.1.2.4 Flying Capacitors
The flying capacitors (C1, C2) transfer charge from the input to the output. Flying capacitance can impact both
output current capability and ripple magnitudes. If flying capacitance is too small, the LM2757 may not be able to
regulate the output voltage when load currents are high. On the other hand, if the flying capacitance is too large,
the flying capacitor might overwhelm the input and output capacitors, resulting in increased input and output
ripple.
In typical high-current applications, 0.47-µF low-ESR ceramic capacitors are recommended for the flying
capacitors. Polarized capacitors (tantalum, aluminum electrolytic, etc.) must not be used for the flying capacitor,
as they could become reverse-biased during LM2757 operation.
9.2.1.2.5 Recommended Capacitance
The data in Table 4 can be used to assist in the selection of capacitance for each node that best balances
solution size and cost with the electrical requirements of the application.
As previously discussed, input and output ripple voltages varies with output current and input voltage. The
numbers provided show expected ripple voltage with VIN = 3.6 V and a load current of 200 mA at 5-V output, 100
mA at 4.5-V output, and 100 mA at 4.1-V output. Table 4 offers a first look at approximate ripple levels and
provides a comparison of different capacitance configurations, but is not intended to ensure performance. With
any capacitance configuration chosen, always verify that the performance of the ripple waveforms are suitable for
the intended application. The same capacitance value must be used for all the flying capacitors. For output
regulation performance with different capacitor configurations, please refer to the output voltage vs. input voltage
graphs in Typical Characteristics. The output voltage regulation is typically better when using capacitors with a
higher capacitance value and a higher voltage bias rating than the nominal voltage applied to them, as can be
seen in the graphs, but this may have an impact in capacitor case size. For typical high-current small solution
size applications, 1-µF capacitance X5R temperature characteristic rating 0402 (C1005) case size and 10-V bias
or higher capacitors can be used for the input, output and flying capacitors. According to current capacitor
offerings, there are no capacitors in the 0201 (C0603) case size that satisfy the minimum capacitance
requirements of the LM2757 circuit. When selecting capacitors, those with the highest voltage bias rating
available from the capacitor supplier are preferred.
Table 4. LM2757 Performance With Different Capacitor Configurations(1)
CAPACITOR CONFIGURATION 5-V, 200-mA OUTPUT 4.5-V, 100-mA OUTPUT 4.1-V, 100-mA OUTPUT
(VIN = 3.6 V) RIPPLE (mV)(typical) RIPPLE (mV) (typical) RIPPLE (mV)(typical)
CIN = 1 µF, COUT = 1 µF, C1and C2= 0.47 µF 32 12 11
CIN = 0.68 µF, COUT = 1 µF, C1and C2= 0.47 µF 32 11 11
CIN = 0.68 µF, COUT = 0.47 µF, C1and C2= 0.47 µF 51 151 15
CIN = 0.68 µF, COUT = 0.47 µF, C1and C2= 0.22 µF 53 181 18
(1) Refer to the text in Recommended Capacitance for detailed information on the data in this table.
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
9.2.1.3 Application Curves
5-V Mode 4.5-V Mode
Figure 22. Efficiency vs. Input Voltage Figure 23. Efficiency vs. Input Voltage
4.1-V Mode
Figure 24. Efficiency vs. Input Voltage
9.2.2 USB OTG / Mobile HDMI Power Supply
The 5-V output mode is normally used for the USB OTG / Mobile HDMI application. Therefore, the LM2757 can
be enabled or disabled by applying a logic signal on only the M1 pin while grounding the M0 pin. Depending on
the USB/HDMI mode of the application, the LM2757 can be enabled to drive the power bus line (Host), or
disabled to put its output in high impedance allowing an external supply to drive the bus line (Slave). In addition
to the high-impedance backdrive protection, the output current limit protection is 250 mA (typical), well within the
USB OTG and HDMI requirements.
16 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
USB OTG
Transceiver
LM2757 (Host
Mode VBUS
Power)
Dual Role
Application
Processor
EN (VM1)
VBAT (System Voltage)
VOUT / VBUS (5V)
ID
D+
D-
GND
VBUS
VM0 USB Connector
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
Figure 25. USB OTG / Mobile HDMI
9.2.3 Supercapacitor Flash Driver
Using the 5-V output voltage mode, the LM2757 can charge a supercapacitor for LED flash applications while
limiting the peak current drawn off the battery during the charge cycle. The LM2757 can be disabled for the Flash
event, placing its output in high impedance with the input. In this way, all charge for the flash LED(s) comes
directly off the supercapacitor and does not load the main battery line. The LM2757 can be enabled or disabled
by applying a logic signal on only the M1 pin while grounding the M0 pin.
Special consideration must be given when using supercapacitors for LED flash applications where the voltage on
the capacitor is charged to a fixed value. This is due to the possible power management issues that can arise as
a result of the high flash current and wide tolerance ranges (V–I characteristics) of typical flash LEDs. If the
voltage across the Flash LED(s) is not managed, damage may occur where a relatively low Vf LED is overdriven
or places excessive voltage across the bottom control FET. To help avoid this issue, the use of a high-power
current sink is advised in applications where the forward voltage specification of the flash LED has a wide range.
Figure 26. Supercapacitor Flash Driver
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM2757
LM2757
LED
Driver
VBAT VOUT = 4.1V (100 mA), 4.5V (110 mA)
5.0V (180 mA)
M0
M1
D1DX
R R
LED(s)
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
9.2.4 LED Driver
The 5-V, 4.5-V, or the 4.1-V mode can be used depending on the forward voltage and load requirements of the
LED application. The LM2757 can be enabled or disabled by applying the appropriate combination of logic
signals on the M1 and M0 pins. LED current for each string in this application is limited by the voltage across the
string's ballast resistor, which is dependent on the output voltage mode selected and the V-I profile of each LED
used.
Figure 27. LED Driver
10 Power Supply Recommendations
The LM2757 is designed to operate as an inverter over an input voltage supply range between 2.7 V and 5.5 V.
18 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
C2+ VOUT
C1- VIN VIN
C1+
GND
GND C2-
M1NC
1 PF
GND C2-
M0M1
VIN
M0
VIAs to
GND
Plane
1 PF
1 PF
1 PF
VOUT
C2+
C1-
C1+
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
11 Layout
11.1 Layout Guidelines
Proper board layout helps to ensure optimal performance of the LM2757 circuit. The following guidelines are
recommended:
Place capacitors as close to the LM2757 as possible, and preferably on the same side of the board as the
device.
Use short, wide traces to connect the external capacitors to the LM2757 to minimize trace resistance and
inductance.
Use a low resistance connection between ground and the GND pin of the LM2757. Using wide traces and/or
multiple vias to connect GND to a ground plane on the board is most advantageous.
11.2 Layout Example
Figure 28. LM2757 Layout Example
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM2757
LM2757
SNVS536F OCTOBER 2007REVISED JULY 2015
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation see the following:
Texas Instruments Application Note 1112 DSBGA Wafer Level Chip Scale Package (SNVA009).
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.6 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
20 Submit Documentation Feedback Copyright © 2007–2015, Texas Instruments Incorporated
Product Folder Links: LM2757
LM2757
www.ti.com
SNVS536F OCTOBER 2007REVISED JULY 2015
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM2757
PACKAGE OPTION ADDENDUM
www.ti.com 5-Jul-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2757TM/NOPB ACTIVE DSBGA YFQ 12 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -30 to 85 DL
LM2757TMX/NOPB ACTIVE DSBGA YFQ 12 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -30 to 85 DL
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
PACKAGE OPTION ADDENDUM
www.ti.com 5-Jul-2015
Addendum-Page 2
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2757TM/NOPB DSBGA YFQ 12 250 178.0 8.4 1.35 1.75 0.76 4.0 8.0 Q1
LM2757TMX/NOPB DSBGA YFQ 12 3000 178.0 8.4 1.35 1.75 0.76 4.0 8.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 7-Jul-2015
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2757TM/NOPB DSBGA YFQ 12 250 210.0 185.0 35.0
LM2757TMX/NOPB DSBGA YFQ 12 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 7-Jul-2015
Pack Materials-Page 2
MECHANICAL DATA
YFQ0012xxx
www.ti.com
TMD12XXX (Rev B)
E
0.600
±0.075
D
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
4215079/A 12/12
D: Max =
E: Max =
1.641 mm, Min =
1.248 mm, Min =
1.581 mm
1.187 mm
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM2757TM/NOPB LM2757TMX/NOPB