HMC892LP5E v00.0910 Typical Applications Features The HMC892LP5E is ideal for: Fast Tuning Response; 200 ns * Test & Measurement Equipment Excellent Wideband Rejection; >30 dB * Military RADAR & EW/ECM Single Chip Replacement for Mechanically Tuned Designs * SATCOM & Space * Industrial & Medical Equipment 32 Lead 5x5 mm SMT Package General Description TE Functional Diagram LE The HMC892LP5E is a MMIC band pass filter which features a user selectable passband frequency. The 3 dB filter bandwidth is approximately 9%. The 20 dB filter bandwidth is approximately 23%. The center frequency can be varied between 4 and 7.7 GHz by applying an analog tune voltage between 0 and 14V. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC892LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. B SO FILTERS - TUNABLE - SMT 3 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Electrical Specifications, TA = +25C, Vfctl = Vbwctl Unless Otherwise Stated Parameter Fcenter Tuning Range Min. Typ. 4 3 dB Bandwidth Max. Units 7.7 GHz 9 % 0.9*Fcenter GHz High Side Rejection Frequency (Rejection >20 dB) 1.13*Fcenter GHz Re-entry Frequency (Rejection <30 dB) 2.5*Fcenter GHz O Low Side Rejection Frequency (Rejection >20 dB) 3 dB Bandwidth Control (Vbwctl) 3 % Insertion Loss 8 dB Return Loss 9 Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) 0 Source/Sink Current (Ifctl) Bandwidth Control Voltage (Vbwctl) dB 10 0 Source/Sink Current (Ibwctl) dBm 14 V 1 mA 14 V 1 mA Residual Phase Noise [1] (1 MHz Offset) -165 dBc/Hz Fcenter Drift Rate -0.65 MHz/C Tuning Characteristics [2] tFULLBAND (0% Vfctl to 90% RF) 200 ns [1] Optimum residual phase noise performance requires the use of a low noise driver circuit. [2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay. 3-1 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl 0V 7V 14V -5 RETURN LOSS (dB) -20 -30 -40 -50 -10 S11 S22 -15 -20 TE INSERTION LOSS (dB) -10 0V -25 -60 7V 14V -30 -70 0 5 10 15 20 25 0 30 FREQUENCY (GHz) 5 10 15 20 25 30 8 9 FREQUENCY (GHz) Insertion Loss vs. Control Voltages, Vfctl = Vbwctl LE Return Loss vs. Control Voltages, Vfctl = Vbwctl 0 0 -2 -6 -10 -12 -14 -16 -18 -20 3 B SO 0V 7V 14V -8 4 5 6 7 8 RETURN LOSS (dB) -5 -4 -10 -15 7V 0V 14V -20 S11 S22 -25 -30 3 9 4 5 6 7 FREQUENCY (GHz) FREQUENCY (GHz) Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V FILTERS - TUNABLE - SMT 0 0 INSERTION LOSS (dB) 3 Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl O Return Loss vs. Temperature, Vfctl = Vbwctl = 7V 0 0 -5 -4 -6 RETURN LOSS (dB) INSERTION LOSS (dB) -2 +25C +85C -40C -8 -10 -12 -14 -16 S11 -10 S22 -15 -20 +25C +85C -40C -25 -18 -20 -30 3 4 5 6 7 FREQUENCY (GHz) 8 9 3 4 5 6 7 8 9 FREQUENCY (GHz) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 3-2 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 3 Broadband Return Loss vs. Vbwctl, Vfctl = 7V Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V 0 Vbwctl=4V Vbwctl=7V Vbwctl=10V -5 -30 -40 -50 -60 -10 -15 S11 S22 Vbwctl=10V -20 -25 Vbwctl=7V -30 -70 -80 -35 0 5 10 15 20 25 30 0 FREQUENCY (GHz) 5 10 15 20 30 LE Return Loss vs. Vbwctl, Vfctl = 7V 0 0 -2 Vbwctl=4V Vbwctl=7V Vbwctl=10V -4 -5 -8 -10 -12 -14 -20 3 B SO -6 -18 4 5 6 7 8 Vbwctl=4V -10 Vbwctl=7V -15 Vbwctl=10V -20 S11 S22 -25 -30 3 9 4 5 6 7 FREQUENCY (GHz) Center Frequency vs. Temperature, Vfctl = Vbwctl Insertion Loss vs. Temperature, Vfctl = Vbwctl O FREQUENCY (GHz) 9 8 -2 +25C +85C -40C 7 8 9 0 INSERTION LOSS (dB) CENTER FREQUENCY (GHz) 25 FREQUENCY (GHz) Insertion Loss vs. Vbwctl, Vfctl = 7V -16 6 5 4 +25C +85C -40C -4 -6 -8 -10 -12 -14 3 -16 0 2 4 6 Vfctl (V) 3-3 Vbwctl=4V TE RETURN LOSS (dB) -20 RETURN LOSS (dB) INSERTION LOSS (dB) -10 INSERTION LOSS (dB) FILTERS - TUNABLE - SMT 0 8 10 12 14 0 2 4 6 8 10 12 14 Vfctl (V) Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl +25C +85C -40C RETURN LOSS (dB) 10 9 -4 -6 -8 TE 8 -10 7 -12 6 0 2 4 6 8 10 12 0 14 2 4 6 8 10 12 14 12 14 Vfctl (V) Vfctl (V) 1 High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] LE Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 1.3 +25C +85C -40C 0.95 0.9 0.85 0.8 0 B SO F20dB TO Fcenter RATIO +25C +85C -40C -2 2 4 6 8 10 12 F20dB To Fcenter RATIO BANDWIDTH (%) 11 1.2 1.15 1.1 1.05 1 14 0 Vfctl (V) Tuning Sensitivity vs. Temperature, Vfctl = Vbwctl 2 4 6 8 10 Vfctl (V) O Group Delay 600 2.5 500 0V GROUP DELAY (ns) 2 400 300 +25C +85C -40C 200 +25C +85C -40C 1.25 FILTERS - TUNABLE - SMT 0 12 SENSITIVITY (MHz/V) 3 7V 1.5 14V 1 0.5 100 0 0 2 4 6 Vfctl (V) 8 10 12 14 0 2 3 4 5 6 7 FREQUENCY (GHz) 8 9 10 [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 3-4 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 3 3 dB Bandwidth vs. Bandwidth Control Insertion Loss vs. Bandwidth Control 0 14 INSERTION LOSS (dB) Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V 12 10 -5 -10 TE 8 6 4 2 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V -15 -20 0 2 4 6 8 10 12 14 0 Vfctl (V) 2 4 6 10 12 14 High Side Rejection Ratio vs. Bandwidth Control [1] LE Low Side Rejection Ratio vs. Bandwidth Control [1] 1 1.3 0.95 0.85 0.8 B SO 0.9 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V 0.75 0.7 0 2 4 6 8 10 12 1.2 1.15 1.1 1.05 1 14 0 2 4 6 10 12 14 Input IP3 vs. Power Input Vfctl = Vbwctl 35 0 Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V -2 8 Vfctl (V) O Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control Vbwctl=Vfctl Vbwctl=Vfctl+3V Vbwctl=Vfctl-3V 1.25 Vfctl (V) 30 -4 IP3 (dBm) RETURN LOSS (dB) 8 Vfctl (V) F20dB TO Fcenter RATIO BANDWIDTH (%) 16 F20dB TO Fcenter RATIO FILTERS - TUNABLE - SMT 18 -6 25 20 Pin = 0 Pin = 5 Pin = 10 Pin = 15 Pin = 20 -8 15 -10 10 -12 0 2 4 6 Vfctl (V) 8 10 12 14 3.5 4.5 5.5 6.5 7.5 8.5 FREQUENCY (GHz) [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to center 3-5 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz 0.5V 5.8V 13.0V -140 Frequency Control Voltage (Vfctl) -0.5 to +15V Bandwidth Control Voltage (Vbwctl) -0.5 to +15V RF Power Input 26 dBm Storage Temperature -65 to +150 C ESD Rating (HBM) Class 1B -150 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS TE RESIDUAL PHASE NOISE (dBc/Hz) -120 -130 3 Absolute Maximum Ratings -160 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 Reliability Information 1.0e+7 Junction Temperature to Maintain 1 Million Hour MTTF 150 C Nominal Junction Temperature (T= 85 C and Pin = 10 dBm) 90 C Operating Temperature -40 to +85 C LE OFFSET FREQUENCY (Hz) O B SO Outline Drawing FILTERS - TUNABLE - SMT Residual Phase Noise Vfctl = Vbwctl NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC892LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H892 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 3-6 HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz Pin Descriptions Description 1 - 4, 7 - 11, 13 15 - 18, 21 - 32 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 5, 20 GND These pins and exposed paddle must be connected to RF/DC ground. 6 RFIN This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. 12 Vfctl Center frequency control voltage. 14 Vbwctl Interface Schematic TE Function LE Pin Number Bandwidth control voltage. B SO FILTERS - TUNABLE - SMT 3 19 RFOUT This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. O Application Circuit 3-7 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC892LP5E v00.0910 FILTER - TUNABLE, BAND PASS SMT 4.0 - 7.7 GHz TE LE B SO FILTERS - TUNABLE - SMT 3 Evaluation PCB O List of Materials for Evaluation PCB 128531 [1] Item Description J1, J2 SMA - SRI J3, J4 SMA - Johnson C1, C2 100 pF Capacitor, 0402 Pkg. U1 HMC892LP5E Filter PCB [2] 127338 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, delivery, andRoad, to place orders: Analog Devices, For price, delivery and to for place Hittite Microwave Corporation, 20 Alpha Chelmsford, MA 01824Inc., responsibility is assumed by Analog Devices its use, orders: nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 3-8 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC892LP5E 128531-HMC892LP5E HMC892LP5ETR