Huanan Electronic Technology Co.,Ltd
4/F, Block B, Anhongji Technology Industrial Estate, Min Zhi Street, Longhua District Shenzhen
City, GuangDong Province, China
TEL: +86 755 -33168098
FAX: +86 755 -23272656
SPECIFICATION
FOR
LCD MODULE
MODULE NO.: HTF0177SN-01
DOC.REVISION V1
Customer Approval:
SIGNATURE DATE
PREPARED BY
(RD ENGINEER) HA
2012-06-24
PREPARED BY
(QA ENGINEER)
CHECKED BY
APPROVED BY
History of Versions and Modifications
Version Modifications Date
V1.0 Generation fir st vers ion Jun 24,2012
PAGE:2
MODEL No:HTF0177SN-01
CONTENTS
NO. ITEM PAGE
-Cover 1
-History of Versions and Modifications 2
-contents 3
1 General Specifications 4
2 Outline Drawing 5
3 Absolute Maximum Ratings 6
4 Led Backlight Specification and Interface Signal 7
5 Optical Characteristics 10
6 Cell test light waveform 12
7 Precautions for Use of LCD Modules 13
PAGE:3
MODELNo:HTF0177SN-01
1.General Specifications
drawing on next page
Note 1: Select by software, and color tune is slightly changed by temperature and driving
voltage.
TBD- To Be Determined.
Requirements on Environmental Protection:RoHS
Note 2:
Note 3:
PAGE:4
Item Main LCD Unit Note
LCD Type 1.77 TFT LCD -
Display color 262K
LCD Duty 1/160 -
LCD Bias --
Viewing Direction 12:00 OClock
Viewing Area(W H) -mm
Active Area(W H) 28.032X35.04 mm
Number of Dots 128(R,G,B) 160 mm
Dot Size(W H) -mm
Dot Pitch(W H) mm
Controller ILI9163
V
DD
2.7~3.3V V
Outline Dimensions Refer to outline
Backlight LED(white) -
Operating Temperature -20 +70 -
Storage Temperature -30 +80 -
We ig ht TBD g
Data Transfer 4 Line serial -
Display Type Transmissive type -
MODEL No:HTF0177SN-01
2XWOLQH'UDZLQJ
3$*(
MODEL No:H7)6101
3. Absolute Maximum Raings
ITEM SYMBOL MIN. MAX. UNIT NOTE
Operating Ambient Temperature TOP -20 +70 C
Operating Ambient Humidity HOP 10 90 % (RH)
Storage Temperature TSTG -30 +80 C
Storage Humidity HSTG 10 90 % (RH)
Note 1.
The absolute maximum ratings are the values that must not be exceeded at any time for this product. It
is not allowed for any of these ratings to be exceeded. Should a product be used with any of the absolute
maximum ratings exceeded, the characteristics of the product may not be recovered, or in an extreme
case, the product may be permanently destroyed.
Therefore, when designing a system incorporating the product, make sure that adequate attentions be
paid to the variations in the supply voltages, the characteristics of parts that are connected, surges in the
input and output lines, and the ambient temperatures.
Note 2.
This specification applys after the driver IC mounting and the FPC mounting.
(This specification isnt applicable at time of driver IC un-mounting and FPC un-mounting.)
LCD should keep the condition that dew dosent storage in case of driver IC un-mounting and FPC un-
mounting. Dew may break the LCD. Especially part is very weak for dew.
PAGE:6
MODEL No:HTF0177SN-01
4. LED backlight specification and Interface Signal
4.1 LED backlight specification
3$*(
MODEL No: 07)6110
4.2 Interface Signal
.
PAGE:8
MODEL No:HTF0177SN-01
PIN
No. SYMBOL Function
2 GND System Ground
1 NC No connection
5 GND System Ground
12 CS Chip enable,active low
6 RESET Reset Signal pin (“Low” is enable)
9 SCK Serial Clock.
8 SDA Serial data input
10 VCC Power supply
11 IOVC Power supply forthe I/Ocircuit.
14 NC No connection
7 RS Command/display data select pin
13 GND System Ground
4 LEDA Backlight LED Anode.
3 LEDK Backlight LED1 Cathode.
5. Optical Characteristics
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT REMARK
Transmittance(%) T (5.8)
Luminance L (180) (200) cd/m2
Luminance Uniformity L(80) Note 3
Contrast Ratio CR (300) Note 4
NTSC Ratio --- (61%)
Tr (10) ms
Response Time Tf =0 (15) ms Note 5
Upper (60)
Lower (55)
Left (50)
View angle
Right
CR 10
(50)
Note 6
x(0.313)
Wy(0.329)
x(0.6457)
Ry(0.3391)
x(0.3438)
Gy(0.6012)
x(0.1476)
Color
Coordinate
BY
=0
(0.1110)
Note 1. Ambient condition 25 2 6010%RH under 10 Lunx in the darkroom
Note 2. Measure device BM-5A (TOPCON) viewing cone=1 IL=20mA, after 10 minutes operation.
Note 3. Definition of Luminance Uniformity L = L(MIN) / L (MAX) 100%
L=500mm
1
PAGE:9
MODEL No:HTF0177SN-01
Note 4. Definition of Contrast Ratio
CR = White Luminance (ON) / Black Luminance (OFF)
Note 5. Definition of response time The response time is defined as the time interval between the 10% and
90% amplitudes.
Note 6. Definition of view angle( )
Panel
PAGE:10
MODEL No:HTF0177SN-01
6. Cell test light waveform
Timing
PAGE:11
MODEL No:HTF0177SN-01
7.
Pr
ecautions for Use of LCD Modules
7.1 HandlingPrecautions
7.1.1 The display panel is made of glass. Do not subject it to a
mechanical shock by dropping it from a high place, etc.
7.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out,
be sure not to get any in your mouth, if the substance comes into contact with your
skin or clothes, promptly wash it off using soap and water.
7.1.3 Do not apply excessive force to the display surface or the adjoining areas since this
may cause the color tone to vary.
7.1.4 The polarizer covering the display surface of the LCD module is
and easily scratched. Handle this polarizer carefully.
7.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with
a soft dry cloth. If still not completely clear, moisten cloth with one of the following
solvents:
Isopropyl alcohol
Ethyl alcohol
Solvents other than those mentioned above may damage the polarizer. Especially,
do not use the following:
Wat er
Ketone
Aromatic solvents
7.1.6 Do not attempt to disassemble the LCD Module.
7.1.7 If the logic circuit power is off, do not apply the input signals.
7.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an
optimum work environment.
a. Be sure to ground the body when handling the LCD Modules.
b. Tools required for assembly, such as soldering irons, must be properly ground.
c. To reduce the amount of static electricity generated, do not conduct assembly and
other work under dry conditions.
PAGE:12
MODEL No:HTF0177SN-01
d. The LCD Module is coated with a film to protect the display surface. Be care when
peeling off this protective film since static electricity may be generated.
7.2 Storage precautions
7.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of
fluorescent lamps.
7.2.2 The LCD modules should be stored under the storage temperature range. If the LCD
modules will be stored for a long time, the recommend condition is:
040
Temperature :
Relatively humidity: 80%
7.2.3 The LCD modules should be stored in the room without acid, alkali and harmful
gas.
7.3 The LCD modules should be no falling and violent shocking during transportation, and
also should avoid excessive press, water, damp and sunshine.
PAGE:13
MODEL No:HTF0177SN-01
