ACS758LCB-100U-PFF-T - Allegro Microsystems

Application 1. The ACS758 outputs an analog signal, VOUT

, that

varies linearly with the uni- or bi-directional AC or DC primary

sampled current, IP

, within the range specified. CF is for optimal

noise management, with values that depend on the application.

ACS758xCB

Description

The Allegro® ACS758 family of current sensor ICs provides

economical and precise solutions for AC or DC current sensing.

Typical applications include motor control, load detection and

management, power supply and DC-to-DC converter control,

inverter control, and overcurrent fault detection.

The device consists of a precision, low-offset linear Hall

circuit with a copper conduction path located near the die.

Applied current flowing through this copper conduction path

generates a magnetic field which the Hall IC converts into a

proportional voltage. Device accuracy is optimized through the

close proximity of the magnetic signal to the Hall transducer.

A precise, proportional output voltage is provided by the

low-offset, chopper-stabilized BiCMOS Hall IC, which is

programmed for accuracy at the factory.

High level immunity to current conductor dV/dt and stray

electric fields, offered by Allegro proprietary integrated shield

technology, guarantees low output voltage ripple and low offset

drift in high-side, high voltage applications.

The output of the device has a positive slope (>VCC

/ 2) when an

increasing current flows through the primary copper conduction

path (from terminal 4 to terminal 5), which is the path used

for current sampling. The internal resistance of this conductive

path is 100 μΩ typical, providing low power loss.

The thickness of the copper conductor allows survival of the

device at high overcurrent conditions. The terminals of the

ACS758-DS, Rev. 6

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

Continued on the next page…

Typical Application

+3.3 or 5 V

VOUT

CBYP

0.1 F

IP+

IP–

GND

ACS758

VIOUT

VCC

Features and Benefits

▪ Industry-leading noise performance through proprietary

amplifier and filter design techniques

▪ Integrated shield greatly reduces capacitive coupling from

current conductor to die due to high dV/dt signals, and

prevents offset drift in high-side, high voltage applications

▪ Total output error improvement through gain and offset

trim over temperature

▪ Small package size, with easy mounting capability

▪ Monolithic Hall IC for high reliability

▪ Ultra-low power loss: 100 μΩ internal conductor resistance

▪ Galvanic isolation allows use in economical, high-side

current sensing in high voltage systems

▪ 3.0 to 5.5 V, single supply operation

PSS

Leadform

PFF

Leadform

Package: 5-pin package

Additional leadforms available for qualifying volumes

TÜV America

Certificate Number:

U8V 09 05 54214 021

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Selection Guide

Part Number1

Package Primary Sampled

Current , IP

(A)

Sensitivity

Sens (Typ.)

(mV/A)

Current

Directionality

TOP

(°C) Packing2

Terminals Signal Pins

ACS758LCB-050B-PFF-T Formed Formed ±50 40.Bidirectional

–40 to 150

34 pieces

per tube

ACS758LCB-050U-PFF-T Formed Formed 50 60.Unidirectional

ACS758LCB-100B-PFF-T Formed Formed ±100 20.Bidirectional

ACS758LCB-100U-PFF-T Formed Formed 100 40.Unidirectional

ACS758KCB-150B-PFF-T Formed Formed ±150 13.3 Bidirectional

–40 to 125ACS758KCB-150U-PFF-T Formed Formed 150 26.7 Unidirectional

ACS758KCB-150B-PSS-T Straight Straight ±150 13.3 Bidirectional

ACS758ECB-200B-PFF-T Formed Formed ±200 10.Bidirectional

–40 to 85ACS758ECB-200U-PFF-T Formed Formed 200 20.Unidirectional

ACS758ECB-200B-PSS-T Straight Straight ±200 10.Bidirectional

1Additional leadform options available for qualified volumes.

2Contact Allegro for additional packing options.

conductive path are electrically isolated from the signal leads (pins

1 through 3). This allows the ACS758 family of sensor ICs to be

used in applications requiring electrical isolation without the use

of opto-isolators or other costly isolation techniques.

The device is fully calibrated prior to shipment from the factory.

The ACS758 family is lead (Pb) free. All leads are plated with 100%

matte tin, and there is no Pb inside the package. The heavy gauge

leadframe is made of oxygen-free copper.

Description (continued)

Features and Benefits (continued)

▪ 120 kHz typical bandwidth

▪ 3 μs output rise time in response to step input current

▪ Output voltage proportional to AC or DC currents

▪ Factory-trimmed for accuracy

▪ Extremely stable output offset voltage

▪ Nearly zero magnetic hysteresis

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Absolute Maximum Ratings

Characteristic Symbol Notes Rating Units

Forward Supply Voltage VCC 8V

Reverse Supply Voltage VRCC –0.5 V

Forward Output Voltage VIOUT 28 V

Reverse Output Voltage VRIOUT –0.5 V

Output Source Current IOUT(Source) VIOUT to GND 3 mA

Output Sink Current IOUT(Sink) VCC to VIOUT 1 mA

Nominal Operating Ambient Temperature TOP

Range E –40 to 85 ºC

Range K –40 to 125 ºC

Range L –40 to 150 ºC

Maximum Junction TJ(max) 165 ºC

Storage Temperature Tstg –65 to 165 ºC

Isolation Characteristics

Characteristic Symbol Notes Rating Unit

Dielectric Strength Test Voltage* VISO Agency type-tested for 60 seconds per

UL standard 60950-1, 2nd Edition 3000 VAC

Working Voltage for Basic Isolation VWFSI For basic (single) isolation per UL standard

60950-1, 2nd Edition

990 VDC or Vpk

700 Vrms

Working Voltage for Reinforced Isolation VWFRI For reinforced (double) isolation per UL standard

60950-1, 2nd Edition

636 VDC or Vpk

450 Vrms

* Allegro does not conduct 60-second testing. It is done only during the UL certification process.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Typical Overcurrent Capabilities1,2

Characteristic Symbol Notes Rating Units

Overcurrent IPOC

TA = 25°C, 1s duration, 1% duty cycle 1200 A

TA = 85°C, 1s duration, 1% duty cycle 900 A

TA = 150°C, 1s duration, 1% duty cycle 600 A

1Test was done with Allegro evaluation board. The maximum allowed current is limited by TJ(max) only.

2For more overcurrent profiles, please see FAQ on the Allegro website, www.allegromicro.com.

Thermal Characteristics may require derating at maximum conditions

Characteristic Symbol Test Conditions* Value Unit

Package Thermal Resistance RθJA

Mounted on the Allegro evaluation board with

2800 mm2 (1400 mm2 on component side and

1400 mm2 on opposite side) of 4 oz. copper con-

nected to the primary leadframe and with thermal

vias connecting the copper layers. Performance

is based on current flowing through the primary

leadframe and includes the power consumed by

the PCB.

7 ºC/W

*Additional thermal information available on the Allegro website

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

IP+

IP–

VIOUT

GND

VCC

Terminal List Table

Number Name Description

1 VCC Device power supply terminal

2 GND Signal ground terminal

3 VIOUT Analog output signal

4 IP+ Terminal for current being sampled

5 IP– Terminal for current being sampled

Functional Block Diagram

Pin-out Diagram

Amp Out

VCC

+3.3 to 5 V

VIOUT

GND

Filter

Dynamic Offset

Cancellation

0.1 μF

IP–

IP+

Gain

Temperature

Coefficient

Gain

Trim Control

Offset

Temperature

Coefficient

Offset

To all subcircuits

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

COMMON OPERATING CHARACTERISTICS1 valid at TOP = –40°C to 150°C and VCC = 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Supply Voltage2VCC 3 5.0 5.5 V

Supply Current ICC Output open – 10 13.5 mA

Power-On Delay tPOD TA = 25°C – 10 – s

Rise Time3trIP step = 60% of IP+, 10% to 90% rise time, TA = 25°C,

COUT = 0.47 nF –3–s

Propagation Delay Time3tPROP TA = 25°C, COUT = 0.47 nF – 1 – s

Response Time tRESPONSE Measured as sum of tPROP and tr–4–s

Internal Bandwidth4BWi–3 dB; TA = 25°C, COUT = 0.47 nF – 120 – kHz

Output Load Resistance RLOAD(MIN) VIOUT to GND 4.7 – – k

Output Load Capacitance CLOAD(MAX) VIOUT to GND – – 10 nF

Primary Conductor Resistance RPRIMARY TA = 25°C – 100 – 

Symmetry3ESYM Over half-scale of Ip 99 100 101 %

Quiescent Output Voltage5

VIOUT(QBI) Bidirectional variant, IP = 0 A, TA = 25°C – VCC/2 – V

VIOUT(QUNI) Unidirectional variant, IP = 0 A, TA = 25°C, VIOUT(QUNI) is

ratiometric to VCC – 0.6 – V

Ratiometry3VRAT VCC = 4.5 to 5.5 V – 100 – %

1Device is factory-trimmed at 5 V, for optimal accuracy.

2Devices are programmed for maximum accuracy at 5.0 V VCC levels. The device contains ratiometry circuits that accurately alter the 0 A Output Volt-

age and Sensitivity level of the device in proportion to the applied VCC level. However, as a result of minor nonlinearities in the ratiometry circuit ad-

ditional output error will result when VCC varies from the 5 V VCC level. Customers that plan to operate the device from a 3.3 V regulated supply should

contact their local Allegro sales representative regarding expected device accuracy levels under these bias conditions.

3See Characteristic Definitions section of this datasheet.

4Calculated using the formula BWi = 0.35 / tr.

5VIOUT(Q) may drift over the lifetime of the device by as much as ±25 mV.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

X050B PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 150°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP–50 – 50 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 40 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 150°C – 39.4 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms,TOP = –40°C to 25°C – 41 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 10 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms –1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 150°C – ±15 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±35 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 50 A – 100 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 150°C – –1.2 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 2 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 2.5 V.

4Percentage of IP. Output filtered.

X050U PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 150°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP0 – 50 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 60 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 150°C – 59 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms,TOP = –40°C to 25°C – 61 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 15 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms –1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 150°C – ±20 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±40 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 50 A – 100 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 150°C – –1.2 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 2 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 0.6 V.

4Percentage of IP. Output filtered.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

X100B PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 150°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP–100 – 100 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 20 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 150°C – 19.75 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 20.5 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 6 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms –1.25 – 1.25 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 150°C – ±20 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±20 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 100 A – 150 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 150°C – –1.3 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 2.4 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 2.5 V.

4Percentage of IP. Output filtered.

X100U PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 150°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP0 – 100 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 40 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 150°C – 39.5 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 41 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 12 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms –1.25 – 1.25 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 150°C – ±20 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±20 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 100 A – 150 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 150°C – –1.3 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 2.4 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 0.6 V.

4Percentage of IP. Output filtered.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

X150B PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 125°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP–150 – 150 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 13.3 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 125°C – 13.1 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 13.5 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 4 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms – 1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 125°C – ±14 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±24 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 150 A – 205 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 125°C – –1.8 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 1.6 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 2.5 V.

4Percentage of IP. Output filtered.

X150U PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 125°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP0 – 150 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 26.6 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 125°C – 26.6 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 27.4 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 8 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms – 1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 125°C – ±14 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±24 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 150 A – 205 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 125°C – –1.8 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 1.6 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 0.6 V.

4Percentage of IP. Output filtered.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

X200B PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 85°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP–200 – 200 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 10 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 85°C – 9.88 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 10.13 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 3 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms – 1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 85°C – ±15 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±25 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 200 A – 230 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 85°C – –1.2 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 1.2 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 2.5 V .

4Percentage of IP. Output filtered.

X200U PERFORMANCE CHARACTERISTICS1: TOP = –40°C to 85°C, VCC

= 5 V, unless otherwise specified

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Primary Sampled Current IP0 – 200 A

Sensitivity

SensTA Full scale of IP applied for 5 ms, TA = 25°C – 20 – mV/A

Sens

(TOP)HT Full scale of IP applied for 5 ms, TOP = 25°C to 85°C – 19.7 – mV/A

Sens

(TOP)LT Full scale of IP applied for 5 ms, TOP = –40°C to 25°C – 20.3 – mV/A

Noise2VNOISE TA= 25°C, 10 nF on VIOUT pin to GND – 6 – mV

Nonlinearity ELIN Up to full scale of IP

, IP applied for 5 ms – 1 – 1 %

Electrical Offset Voltage3

VOE(TA) IP = 0 A, TA = 25°C – ±5 – mV

VOE(TOP)HT IP = 0 A, TOP = 25°C to 85°C – ±20 – mV

VOE(TOP)LT IP = 0 A, TOP = –40°C to 25°C – ±35 – mV

Magnetic Offset Error IERROM IP = 0 A, TA = 25°C, after excursion of 200 A – 230 – mA

Total Output Error4ETOT(HT) Over full scale of IP

, IP applied for 5 ms, TOP = 25°C to 85°C – –1.2 – %

ETOT(LT) Over full scale of IP

, IP applied for 5 ms, TOP = –40°C to 25°C – 1.2 – %

1See Characteristic Performance Data page for parameter distributions over temperature range.

2±3 sigma noise voltage.

OE(TOP) drift is referred to ideal VIOUT(Q) = 0.6 V .

4Percentage of IP. Output filtered.

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Characteristic Performance Data

Data taken using the ACS758LCB-50B

Accuracy Data

Mean

Typical Maximum Limit Typical Minimum Limit

-10

-20

-30

-40

-50

–50 100 125 150500-25 25 75 –50 100 125 150500-25 25 75

0.45

0.40

0.35

0.30

0.25

0.20

0.15

0.10

0.05

42.0

42.5

41.0

40.5

40.0

39.5

39.0

38.5

100.40

100.35

100.30

100.25

100.20

100.15

100.10

100.05

100.00

99.95

-1

-2

-3

-4

VOE (mV)ELIN (%)

Sens (mV/A)

ESYM (%)

ETOT (%)

(°C)T

(°C)

(°C)T

(°C)

140

120

100

IERROM (mA)

(°C)

Electrical Offset Voltage versus Ambient Temperature

Nonlinearity versus Ambient Temperature

Sensitivity versus Ambient Temperature

Total Output Error versus Ambient TemperatureMagnetic Offset Error versus Ambient Temperature

Symmetry versus Ambient Temperature

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Characteristic Performance Data

Data taken using the ACS758LCB-100B

Accuracy Data

Mean

Typical Maximum Limit Typical Minimum Limit

-5

-10

-15

-20

-25

0.40

0.35

0.30

0.25

0.20

0.15

0.10

0.05

21.2

21.0

20.8

20.6

20.4

20.2

20.0

19.8

19.6

19.4

19.2

100.6

100.5

100.4

100.3

100.2

100.1

100.0

99.9

99.8

99.7

-1

-2

-3

-4

-5

VOE (mV)ELIN (%)

Sens (mV/A)ESYM (%)

ETOT (%)

(°C)T

(°C)

(°C)T

(°C)

200

190

180

170

160

150

130

120

110

100

IERROM (mA)

(°C)

–50 100 125 150500-25 25 75

Electrical Offset Voltage versus Ambient Temperature

Nonlinearity versus Ambient Temperature

Sensitivity versus Ambient Temperature

Total Output Error versus Ambient TemperatureMagnetic Offset Error versus Ambient Temperature

Symmetry versus Ambient Temperature

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Characteristic Performance Data

Data taken using the ACS758KCB-150B

Accuracy Data

Mean

Typical Maximum Limit Typical Minimum Limit

-5

-10

-15

-20

-25

-30

–60 60 100 120 14080–40 40–20 200–60 60 100 120 14080–40 40–20 200

–60 60 100 120 14080–40 40–20 200

0.30

0.25

02.0

0.15

0.10

0.05

14.0

13.8

13.6

13.4

13.2

13.0

12.8

12.6

100.7

100.6

100.5

100.4

100.3

100.2

100.1

100.0

99.9

99.8

-1

-2

-3

-4

-5

-6

VOE (mV)ELIN (%)

Sens (mV/A)ESYM (%)

ETOT (%)

(°C)T

(°C)

(°C)T

(°C)

–60 60 100 120 14080–40 40–20 200

300

250

200

150

100

IERROM (mA)

(°C)

Electrical Offset Voltage versus Ambient Temperature

Nonlinearity versus Ambient Temperature

Sensitivity versus Ambient Temperature

Total Output Error versus Ambient TemperatureMagnetic Offset Error versus Ambient Temperature

Symmetry versus Ambient Temperature

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Characteristic Performance Data

Data taken using the ACS758ECB-200B

Accuracy Data

Mean

Typical Maximum Limit Typical Minimum Limit

-5

-10

-15

-20

-25

-30

–60 60 100 120 14080–40 40–20 200–60 60 100 120 14080–40 40–20 200

–60 60 100 120 14080–40 40–20 200

0.16

0.14

0.12

0.10

0.08

0.06

0.04

0.02

-0.02

-0.04

-0.06

10.4

10.3

10.2

10.1

10.0

9.9

9.8

9.7

9.6

9.5

100.8

100.6

100.4

100.2

100.0

99.8

99.6

-1

-2

-3

-4

-5

-6

VOE (mV)ELIN (%)

Sens (mV/A)ESYM (%)

ETOT (%)

(°C)T

(°C)

(°C)T

(°C)

–60 60 100 120 14080–40 40–20 200

350

300

250

200

150

100

IERROM (mA)

(°C)

Electrical Offset Voltage versus Ambient Temperature

Nonlinearity versus Ambient Temperature

Sensitivity versus Ambient Temperature

Total Output Error versus Ambient TemperatureMagnetic Offset Error versus Ambient Temperature

Symmetry versus Ambient Temperature

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Characteristic Performance Data

Data taken using the ACS758LCB-100

Timing Data

IP (20 A/div.)

2.988 μs

VIOUT (0.5 V/div.)

t (2 μs/div.)

IP (20 A/div.)

VIOUT (0.5 V/div.)

t (2 μs/div.)

VCC

VIOUT (1 V/div.)

(IP = 60 A DC)

t (2 μs/div.)

IP (20 A/div.)

VIOUT (0.5 V/div.)

t (2 μs/div.)

3.960 μs

9.034 μs

997 ns

Response Time

Propagation Delay Time

Power-on Delay

Rise Time

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Sensitivity (Sens). The change in device output in response to a

1 A change through the primary conductor. The sensitivity is the

product of the magnetic circuit sensitivity (G / A) and the linear

IC amplifier gain (mV/G). The linear IC amplifier gain is pro-

grammed at the factory to optimize the sensitivity (mV/A) for the

half-scale current of the device.

Noise (VNOISE). The noise floor is derived from the thermal and

shot noise observed in Hall elements. Dividing the noise (mV)

by the sensitivity (mV/A) provides the smallest current that the

device is able to resolve.

Nonlinearity (ELIN). The degree to which the voltage output

from the IC varies in direct proportion to the primary current

through its half-scale amplitude. Nonlinearity in the output can be

attributed to the saturation of the flux concentrator approaching

the half-scale current. The following equation is used to derive

the linearity:

100 1–

[{

VIOUT_half-scale amperes – VIOUT(Q)

Δ gain × % sat ( )

2 (VIOUT_quarter-scale amperes – VIOUT(Q) )

where

∆ gain = the gain variation as a function of temperature

changes from 25ºC,

% sat = the percentage of saturation of the flux concentra-

tor, which becomes significant as the current being sampled

approaches half-scale ±IP , and

VIOUT_half-scale amperes = the output voltage (V) when the

sampled current approximates half-scale ±IP .

Symmetry (ESYM). The degree to which the absolute voltage

output from the IC varies in proportion to either a positive or

negative half-scale primary current. The following equation is

used to derive symmetry:

100

VIOUT_+ half-scale amperes – VIOUT(Q)

VIOUT(Q) – VIOUT_–half-scale amperes



Ratiometry. The device features a ratiometric output. This

means that the quiescent voltage output, VIOUTQ, and the mag-

netic sensitivity, Sens, are proportional to the supply voltage, VCC.

The ratiometric change (%) in the quiescent voltage output is

defined as:

5 V

IOUTQ(V

)

IOUTQ(5V)

IOUTQ($V)

=s%

and the ratiometric change (%) in sensitivity is defined as:

VCC 5 V

=s%

$Sens($V

Sens(VCCSens(V

Quiescent output voltage (VIOUT(Q)). Quiescent output voltage

(VIOUT(Q)

). The output of the device when the primary current is

zero. For bidirectional devices, it nominally remains at VCC ⁄ 2.

Thus, VCC = 5 V translates into VIOUT(QBI) = 2.5 V. For unidirec-

tional devices, it nominally remains at 0.12 × VCC . Thus, VCC

= 5 V translates into VIOUT(QUNI) = 0.6 V. Variation in VIOUT(Q)

can be attributed to the resolution of the Allegro linear IC quies-

cent voltage trim, magnetic hysteresis, and thermal drift.

Electrical offset voltage (VOE). The deviation of the device out-

put from its ideal quiescent value of VCC ⁄ 2 for bidirectional and

0.1 × VCC for unidirectional devices, due to nonmagnetic causes.

Magnetic offset error (IERROM). The magnetic offset is due to

the residual magnetism (remnant field) of the core material. The

magnetic offset error is highest when the magnetic circuit has

been saturated, usually when the device has been subjected to a

full-scale or high-current overload condition. The magnetic offset

is largely dependent on the material used as a flux concentrator.

The larger magnetic offsets are observed at the lower operating

temperatures.

Total Output Error (ETOT). The maximum deviation of the

actual output from its ideal value, also referred to as accuracy,

illustrated graphically in the output voltage versus current chart

on the following page.

ETOT is divided into four areas:

 0 A at 25°C. Accuracy at the zero current flow at 25°C, with-

out the effects of temperature.

 0 A over Δ temperature. Accuracy at the zero current flow

including temperature effects.

 Half-scale current at 25°C. Accuracy at the the half-scale current

at 25°C, without the effects of temperature.

 Half-scale current over Δ temperature. Accuracy at the half-

scale current flow including temperature effects.

Definitions of Accuracy Characteristics

Characteristic Definitions

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Output Voltage versus Sampled Current

Total Output Error at 0 A and at Half-Scale Current

Increasing VIOUT

(V)

+IP (A)

Accuracy

25°C Only

Accuracy

25°C Only

Accuracy

25°C Only

Accuracy

0 A

vrOe $Temp erature

Average

VIOUT

–IP (A)

vrOe $Temp erature

Decreasing VIOUT

(V)

IP(min)

IP(max)

Half Scale

Definitions of Dynamic Response Characteristics

Propagation delay (tPROP). The time required for the device

output to reflect a change in the primary current signal. Propaga-

tion delay is attributed to inductive loading within the linear IC

package, as well as in the inductive loop formed by the primary

conductor geometry. Propagation delay can be considered as a

fixed time offset and may be compensated.

Primary Current

Transducer Output

I (%)

Propagation Time, tPROP

Primary Current

Transducer Output

I (%)

Rise Time, trt

Rise time (tr). The time interval between a) when the device

reaches 10% of its full scale value, and b) when it reaches 90%

of its full scale value. The rise time to a step response is used to

derive the bandwidth of the device, in which ƒ(–3 dB) = 0.35 / tr.

Both tr and tRESPONSE are detrimentally affected by eddy current

losses observed in the conductive IC ground plane.

Power-On Time (tPO). When the supply is ramped to its operat-

ing voltage, the device requires a finite time to power its internal

components before responding to an input magnetic field.

Power-On Time, tPO , is defined as the time it takes for the output

voltage to settle within ±10% of its steady state value under an

applied magnetic field, after the power supply has reached its

minimum specified operating voltage, VCC(min), as shown in the

chart at right.

Bidirectional

Unidirectional

Increasing VIOUT

(V)

+IP (A)

Accuracy

25°C Only

Accuracy

25°C Only

Accuracy

0 A

vrOe $Temp erature

Average

VIOUT

–IP (A)

vrOe $Temp erature

Decreasing VIOUT

(V)

IP(max)

Full Scale

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Chopper Stabilization is an innovative circuit technique that is

used to minimize the offset voltage of a Hall element and an asso-

ciated on-chip amplifier. Allegro patented a Chopper Stabiliza-

tion technique that nearly eliminates Hall IC output drift induced

by temperature or package stress effects.

This offset reduction technique is based on a signal modulation-

demodulation process. Modulation is used to separate the unde-

sired DC offset signal from the magnetically induced signal in the

frequency domain. Then, using a low-pass filter, the modulated

DC offset is suppressed while the magnetically induced signal

passes through the filter. The anti-aliasing filter prevents aliasing

from happening in applications with high frequency signal com-

ponents which are beyond the user’s frequency range of interest.

As a result of this chopper stabilization approach, the output

voltage from the Hall IC is desensitized to the effects of tempera-

ture and mechanical stress. This technique produces devices that

have an extremely stable Electrical Offset Voltage, are immune to

thermal stress, and have precise recoverability after temperature

cycling.

This technique is made possible through the use of a BiCMOS

process that allows the use of low-offset and low-noise amplifiers

in combination with high-density logic integration and sample

and hold circuits.

Chopper Stabilization Technique

Amp

Regulator

Clock/Logic

Hall Element

Sample and

Hold

Anti-aliasing

Filter

Low-Pass

Filter

Concept of Chopper Stabilization Technique

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Package CB, 5-pin package, leadform PFF

Creepage distance, current terminals to signal pins: 7.25 mm

Clearance distance, current terminals to signal pins: 7.25 mm

Package mass: 4.63 g typical

1.91

321.4

0.5

0.8

1.5

0.5

Perimeter through-holes recommended

1º±2°

5º±5°

14.0±0.2

17.5±0.2

4.0±0.2

3.0±0.2

2.9±0.2

3.5±0.2

10.00±0.10

13.00±0.10

0.51±0.10

4.40±0.10

7.00±0.10

1.9±0.2

1.50±0.10

Branding scale and appearance at supplier discretion

Dambar removal intrusion

For Reference Only; not for tooling use (reference DWG-9111, DWG-9110)

Dimensions in millimeters

Dimensions exclusive of mold flash, gate burrs, and dambar protrusions

Exact case and lead configuration at supplier discretion within limits shown

Standard Branding Reference View

N = Device part number

T = Temperature code

A = Amperage range

L = Lot number

Y = Last two digits of year of manufacture

W = Week of manufacture

= Supplier emblem

Branded

Face

0.381+0.060

–0.030

NNNNNNN

TTT - AAA

LLLLLLL

YYWW

PCB Layout Reference View

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

231

2.75±0.10

3.18±0.10

1.50±0.10

14.0±0.2

4.0±0.2

3.0±0.2

10.00±0.10

0.51±0.10

7.00±0.10

1.9±0.2

13.00±0.10

4.40±0.10

11.0±0.05

23.50±0.5

0.381+0.060

–0.030

NNNNNNN

TTT - AAA

LLLLLLL

YYWW

Branding scale and appearance at supplier discretion

Dambar removal intrusion

For Reference Only; not for tooling use (reference DWG-9111, DWG-9110)

Dimensions in millimeters

Dimensions exclusive of mold flash, gate burrs, and dambar protrusions

Exact case and lead configuration at supplier discretion within limits shown

Standard Branding Reference View

Branded

Face

N = Device part number

T = Temperature code

A = Amperage range

L = Lot number

Y = Last two digits of year of manufacture

W = Week of manufacture

= Supplier emblem

Package CB, 5-pin package, leadform PSS

Creepage distance, current terminals to signal pins: 7.25 mm

Clearance distance, current terminals to signal pins: 7.25 mm

Package mass: 4.63 g typical

Thermally Enhanced, Fully Integrated, Hall Effect-Based

Linear Current Sensor IC with 100 μ Current Conductor

ACS758xCB

Allegro MicroSystems, Inc.

115 Northeast Cutoff

Worcester, Massachusetts 01615-0036 U.S.A.

1.508.853.5000; www.allegromicro.com

Revision History

Revision Revision Date Description of Revision

Rev. 6 April 9, 2012 Update Unidirectional VIOUT(Q) and Isolation

specifications

The products described herein are protected by U.S. patents: 6,781,359; and 7,265,531.

Allegro MicroSystems, Inc. reserves the right to make, from time to time, such de par tures from the detail spec i fi ca tions as may be required to per-

mit improvements in the per for mance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the

information being relied upon is current.

Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the

failure of that life support device or system, or to affect the safety or effectiveness of that device or system.

The in for ma tion in clud ed herein is believed to be ac cu rate and reliable. How ev er, Allegro MicroSystems, Inc. assumes no re spon si bil i ty for its use;

nor for any in fringe ment of patents or other rights of third parties which may result from its use.

For the latest version of this document, visit our website: