REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R027-94. 93-11-05 Michael A. Frye B Boilerplate update, part of 5 year review. ksr 07-03-05 Joseph Rodenbeck REV SHEET REV B B SHEET 15 16 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Gary L. Gross STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY http://www.dscc.dla.mil Jeffery D. Bowling APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A Michael A. Frye DRAWING APPROVAL DATE 93-04-09 REVISION LEVEL B MICROCIRCUIT, MEMORY, DIGITAL, CMOS, POWER SWITCHED, 32K x 8-BIT PROM, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 1 OF 5962-93166 16 5962-E210-07 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 Federal stock class designator RHA designator (see 1.2.1) \ 93166 01 Device type (see 1.2.2) Q Device class designator (see 1.2.3) / Y Case outline (see 1.2.4) C Lead finish (see 1.2.5) \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 1/ 01 02 03 04 05 06 Circuit function Access time 32K x 8 PROM 32K x 8 PROM 32K x 8 PROM 32K x 8 PROM 32K x 8 PROM 32K x 8 PROM 55 ns 45 ns 35 ns 55 ns 45 ns 35 ns 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class M Q or V Device requirements documentation Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter X Y Z U Descriptive designator GDIP4-T28 or CDIP3-T28 GDFP2-F28 CQCC1-N32 GDIP1-T28 or CDIP2-T28 Terminals 28 28 32 28 Package style Dual-in-line Flat pack Rectangular leadless chip carrier Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1/ Generic numbers are listed on the Standard Microcircuit Drawing Source Approval Bulletin at the end of this document and will also be listed in QML-38535 and MIL-HDBK-103 (see 6.6 herein). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 2 1.3 Absolute maximum ratings. 2/ Supply voltage range -------------------------------------------DC voltage applied to outputs in high Z state ------------DC input voltage -------------------------------------------------DC program voltage---------------------------------------------Maximum power dissipation (PD) ---------------------------Lead temperature (soldering, 10 seconds maximum) --Thermal resistance, junction-to-case (JC) ----------------Junction temperature (TJ)--------------------------------------Storage temperature range------------------------------------Temperature under bias----------------------------------------Data Retention----------------------------------------------------- -0.5 V dc to +7.0 V dc -0.5 V dc to +7.0 V dc -3.0 V dc to +7.0 V dc 13.0 V dc 1.0 W 3/ +260C See MIL-STD-1835 +175C -65C to +150C -55C to +125C 10 years (minimum) 1.4 Recommended operating conditions. Supply voltage (VCC) -------------------------------------------Ground voltage (GND)------------------------------------------Input high voltage (VIH) ----------------------------------------Input Low voltage (VIL) -----------------------------------------Case operating temperature range (TC) -------------------- 4.5 V dc to 5.5 V dc 0.0 V DC 2.0 V dc minimum 0.8 V dc maximum -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM Standard F1192-00 - Standard Guide for the Measurement of Single Event Phenomena from Heavy Ion Irradiation of Semiconductor Devices. (Applications for copies of ASTM publications should be addressed to: ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; http://www.astm.org.) 2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 3/ Must withstand the added PD due to short circuit test e.g.; IOS. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 3 ELECTRONICS INDUSTRIES ASSOCIATION (EIA) JEDEC Standard EIA/JESD78 - IC Latch-Up Test. (Applications for copies should be addressed to the Electronics Industries Association, 2500 Wilson Boulevard, Arlington, VA 22201; http://www.jedec.org.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing shall be as specified on figure 2 herein. When required in screening (see 4.2 herein) or qualification conformance inspection groups A, B, C, or D (see 4.4 herein), the devices shall be programmed by the manufacturer prior to test. A minimum of 50 percent of the total number of cells shall be programmed or at least 25 percent of the total number of cells to any altered item drawing. 3.2.3.2 Programmed devices. The truth tables for programmed devices shall be as specified by an attached altered item drawing. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Min 1,2,3 All Unit Limit Max 2.4 V Output high voltage VOH VCC = 4.5 V, IOH = -2.0 mA, VIN = VIH, VIL Output low voltage VOL VCC = 4.5 V, IOL = 6.0 mA, VIN = VIH, VIL Input high voltage 1/ VIH Input low voltage 1/ VIL Input leakage current IIX GND < VIN < VCC VCC = 5.5 V -10 +10 Output leakage current IOZ GND < VOUT < VCC VCC = 5.5 V -40 +40 Output short circuit current 2/ 3/ IOS VCC = 5.5 V, VOUT = 0.0 V -20 -90 Power supply current ICC VCC = 5.5 V, IOUT = 0 mA, VIN = 0 to 3.0 V, f = fMAX 4/ 5/ 130 Standby supply current ISB VCC = 5.5 V, CS 1 > VIH, IOUT = 0 mA, VIN = 2.0 V 40 Input capacitance 3/ CIN VCC = 5.0 V, T = 25C, f = 1 MHz, (see 4.4.1c) 4 10 Output capacitance 3/ COUT VCC = 5.0 V, T = 25C, f = 1 MHz (see 4.4.1c) 4 10 Functional testing 0.4 2.0 0.8 See 4.4.1d A mA pF 7,8A,8B See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Address to output valid Conditions -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Symbol tAA See figures 3 and 4, and note 6/ Group A subgroups Device type 9,10,11 01,04 55 02,05 45 03,06 35 01,02 30 03 25 04 30 05,06 25 01,02 30 03 25 04 30 05,06 25 01,04 60 02,05 50 03,06 40 01,04 60 02,05 50 03,06 40 Limit Min Unit Max ns Chip select inactive to high Z ( CS 1 and CS2 only) 3/ 7/ Output enable inactive to high Z 3/ 7/ Chip select active to output tHZCS 9,10,11 tHZOE tACS ns valid ( CS 1 and CS2 only) Output enable active to output valid Chip enable inactive to high Z tOE tHZCE ( CE only) 3/ 7/ Chip enable active to output tACE valid ( CE only) See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limit Min Unit Max Chip enable active to power up 3/ tPU ALL Chip enable inactive to power down 3/ tPD 01,04 60 02,05 50 03,06 40 Output hold from address change 3/ ALL tOH 0 0 1/ These are absolute values with respect to device ground and all overshoots and undershoots due to system or tester noise are included. 2/ For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed thirty seconds. 3/ Tested initially and after any design or process changes that affect that parameter, and therefore shall be guaranteed to the limits specified in table I. 4/ At f = fMAX, the inputs are switching at 1/tAA. 5/ Devices 01-03 CE = 0.0 V, CS 1 = 3.0 V, CS2 = 0.0 V; devices 04-06 CE = 0.0 V, OE = 3.0 V. 6/ AC tests are performed with input rise and fall times of 5 ns or less, timing reference levels of 1.5 V, input pulse levels of 0 to 3.0 V, and the output load on figure 3, circuit A. 7/ Transition is measured at steady-state high level -500 mV or steady-state low level +500 mV on the output from the 1.5 V level on the input with the output load on figure 3, circuit B. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 42 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 7 Device Types 01 - 03 04 - 06 Case Outlines X,Y Terminal Number Terminal Symbol Z U Z Terminal Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 GND O3 O4 O5 O6 O7 NC A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC O0 O1 O2 GND NC O3 O4 VPP A12 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 GND O3 O4 O5 O6 O7 NC VPP A12 A7 A6 A5 A4 A3 A2 A1 A0 NC O0 O1 O2 GND NC O3 O4 20 O5 O6 CE A10 O5 21 CE CS2 22 CS 1 O7 OE O7 23 A14 CE A11 CE 24 A13 CS2 A9 A10 25 A12 CS 1 A8 OE 26 A11 NC A13 27 28 29 30 31 32 A10 VCC --------- A14 A13 A12 A11 A10 VCC A14 VCC --------- NC A11 A9 A8 A13 A14 VCC O6 FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 8 Devices 01 - 03 State Programmed Unprogrammed Mode CS2 CS 1 CE A14 - A0 Power Outputs VIH VIL VIL X ICC Data out Standby X X VIH X ISB High Z Output disable X VIH X X ICC High Z Output disable VIL X X X ICC High Z Blank check ones VIHP VPP VILP X ICC Zeros Blank check zeros VILP VPP VILP X ICC Ones Read Devices 04 - 06 State Programmed Mode CE OE VPP A14 - A0 Power Outputs Read VIL VIL X X ICC Data out Standby VIH X X X ISB High Z X VIH X X ICC High Z Blank check ones VIHP VILP VPP X ICC Zeros Blank check zeros VILP VILP VPP X ICC Ones Output disable Unprogrammed NOTES: 1. X = Don't care 2. High Z = High-impedance state FIGURE 2. Truth table STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 9 Circuit A Output load Circuit B Output load for tHZCS, tHZOE, and tHZCE NOTE: Including scope and jig (minimum values). Load Circuit A Circuit B R1 658 658 R2 403 403 30 pF 5 pF CL AC test conditions Input pulse levels Input rise and fall times Input timing reference levels Output reference levels GND to 3.0 V < 5 ns 1.5 V 1.5 V FIGURE 3. Output load circuits and test conditions. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 10 NOTES: 1. CS 1 and CS2 are valid for device types 01-03 only. OE is valid for device types 04-06 only. 2. tHZOE and tOE are valid for device types 04-06 only. FIGURE 4. Switching waveforms. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 11 3.11 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result in a wide variety of configurations, two processing options are provided for selection in the contract using an altered item drawing. 3.11.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.3.1 and table IIA. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program configuration. 3.11.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery. 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Delete the sequence specified as initial (preburn-in) electrical parameters through interim (postburn-in) electrical parameters of method 5004 and substitute lines 1 through 6 of table IIA herein. b. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (1) Dynamic burn-in (method 1015 of MIL-STD-883, test condition D; for circuit, see 4.2.1b herein). c. Interim and final electrical test parameters shall be as specified in table IIA herein. d. A data retention stress test shall be included as part of the screening procedure and shall consist of the following: (Steps 1 through 4 are performed at the wafer level.) (1) Program 100 percent of the total number of cells, excluding the security bit. (2) Bake, unbiased, for 72 hours at +140C or for 48 hours at +150C or for 8 hours at +200C, or 2 hours at +300C for unassembled devices only. (3) Perform margin test using Vm = +5.7 V at +25C using loose timing (i.e., tAA 1 s). (4) Erase. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table IIA herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 12 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table IIA herein. b. Subgroups 5 and 6 of table I of method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 4 (CIN and COUT measurements) shall be measured only for initial qualification and after any process or design changes which may affect input or output capacitance. Capacitance shall be measured between the designated terminal and GND at a frequency equal or less than 1 MHz. Sample size is 15 devices with no failures, and all input and output terminals tested. d. For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table. For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device. e. O/V (latch-up) tests shall be measured only for initial qualification and after any design or process changes which may affect the performance of the device. For device class M, procedures and circuits shall be maintained under document revision level control by the manufacturer and shall be made available to the preparing activity or acquiring activity upon request. For device classes Q and V, the procedures and circuits shall be under the control of the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the preparing activity or acquiring activity upon request. Testing shall be on all pins, on five devices with zero failures. Latch-up test shall be considered destructive. Information contained in JEDEC Standard EIA/JESD78 may be used for reference. f. Devices shall be tested for programmability and ac performance compliance to the requirements of group A, subgroups 9, 10, and 11. Either of two techniques is acceptable: (1) Testing the entire lot using additional built-in test circuitry which allows the manufacturer to verify programmability and ac performance without programming the user array. If this is done, the resulting test patterns shall be verified on all devices during subgroups 9, 10, and 11, group A testing in accordance with the sampling plan specified in MIL-STD-883, method 5005. (2) If such compliance cannot be tested on an unprogrammed device, a sample shall be selected to satisfy programmability requirements prior to performing subgroups 9, 10, and 11. Twelve devices shall be submitted to programming (see 3.2.3.2). If more than two devices fail to program, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 24 total devices with no more than 4 total device failures allowable. Ten devices from the programmability sample shall be submitted to the requirements of group A, subgroups 9, 10, and 11. If more than two devices fail, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 20 total devices with no more than 4 total device failures allowable. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005. b. TA = +125C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 13 TABLE IIA. Electrical test requirements. 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ Test requirements Line no. Subgroups (in accordance with MIL-PRF-38535, table III) Subgroups (in accordance with MIL-STD-883, TM 5005, table I) 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ Device class V Device class Q Device class M 1, 7, 9 or 2, 8A, 10 1 Interim electrical parameters (see 4.2) 2 Static burn-in (method 1015) 3 Same as line 1 4 Dynamic burn-in (method 1015) 5 Same as line 1 6 Final electrical parameters (programmed) (see 4.2) 1*, 2, 3, 7*, 8A, 8B, 9, 10, 11 1*, 2, 3, 7*, 8A, 8B, 9, 10, 11 1*, 2, 3, 7*, 8A, 8B, 9, 10, 11 6A Final electrical parameters (unprogrammed) (see 4.2) 1*, 2, 3, 7*, 8A, 8B 1*, 2, 3, 7*, 8A, 8B 1*, 2, 3, 7*, 8A, 8B 1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11 1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11 1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11 Not required Not required Required 1*, 7* Required Required Required 1*, 7* 7 Group A test requirements (see 4.4) 8 Group C end-point electrical parameters (see 4.4) 2, 3, 7, 8A, 8B 2, 3, 7, 8A, 8B 1, 2, 3, 7, 8A, 8B, 9, 10, 11 9 Group D end-point electrical parameters (see 4.4) 2, 3, 8A, 8B 2, 3, 8A, 8B 2, 3, 8A, 8B 10 Group E end-point electrical parameters (see 4.4) 1, 7, 9 1, 7, 9 1, 7, 9 Blank spaces indicate tests are not applicable. Any or all subgroups may be combined when using high-speed testers. Subgroups 7 and 8 functional tests shall verify the truth table. * indicates PDA applies to subgroup 1 and 7. ** see 4.4.1c. indicates delta limit (see table IIB) shall be required where specified, and the delta values shall be computed with reference to the previous interim electrical parameters (see line 1). See 4.6 See 4.4.1e. Table IIB. Delta limits at +25C. Test 1/ Device types All IIX +10% of specified value in table I IOZ +10% of specified value in table I 1/ The above parameter shall be recorded before and after the required burn-in and life tests to determine the delta. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 14 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table IIA herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C, after exposure, to the subgroups specified in table IIA herein. 4.5 Programming procedure. The programming procedures shall be as specified by the device manufacturer and shall be made available upon request. 4.6 Delta measurements for device class V. Delta measurements, as specified in table IIA, shall be made and recorded before and after the required burn-in screens and steady-state life tests to determine delta compliance. The electrical parameters to be measured, with associated delta limits are listed in table IIB. The device manufacturer may, at his option, either perform delta measurements or within 24 hours after burn-in perform final electrical parameter tests, subgroups 1, 7, and 9. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor prepared specification or drawing. 6.1.2 Substitutability. Device class Q devices will replace device class M devices. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43218-3990, or telephone (614) 692-0547. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 15 6.5 Symbols, definitions, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535, MIL-STD-1331, and as follows: CIN ---------------------------------------- Input terminal capacitance. COUT ------------------------------------- Output terminal capacitance. ICC ---------------------------------------- Supply current. IIX ----------------------------------------- Input current. IOZ ---------------------------------------- Output current. TC ----------------------------------------- Case temperature. VCC --------------------------------------- Positive supply voltage (5.0 V). GND ------------------------------------- Ground zero voltage potential. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-93166 A REVISION LEVEL B SHEET 16 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 07-03-05 Approved sources of supply for SMD 5962-93166 are listed below for immediate acquisition only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9316601MXA 3/ 0C7V7 CY7C271-55DMB QP7C271-55DMB 5962-9316601MYA 3/ 0C7V7 CY7C271-55KMB QP7C271-55KMB 5962-9316601MZA 3/ 0C7V7 CY7C271-55LMB QP7C271-55LMB 5962-9316602MXA 3/ 0C7V7 CY7C271-45DMB QP7C271-45DMB 5962-9316602MYA 3/ 0C7V7 CY7C271-45KMB QP7C271-45KMB 5962-9316602MZA 3/ 0C7V7 CY7C271-45LMB QP7C271-45LMB 5962-9316603MXA 3/ 0C7V7 CY7C271-35DMB QP7C271-35DMB 5962-9316603MYA 3/ 0C7V7 CY7C271-35KMB QP7C271-35KMB 5962-9316603MZA 3/ 0C7V7 CY7C271-35LMB QP7C271-35LMB 5962-9316604MUA 3/ CY7C274-55DMB 5962-9316604MZA 3/ CY7C274-55LMB 5962-9316605MUA 3/ CY7C274-45DMB 5962-9316605MZA 3/ CY7C274-45LMB 5962-9316606MUA 3/ CY7C274-35DMB 5962-9316606MZA 3/ CY7C274-35LMB 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed, contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 0C7V7 Vendor name and address QP Semiconductor 2945 Oakmead Village Court Santa Clara, CA 95051 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in this information bulletin.