Page 2 of 2
Scotch®
Super 88 Vinyl Electrical Tape
Data Sheet
________________________________________________________________________________
_______________________________________________________________________________________
3M UK PLC 3M Ireland 3M UK PLC
Electrical Products Sales Office Sales Office
3M Centre, Cain Road 3M House, Adelphi Centre PO Box 393
Bracknell, Berkshire RG12 1JU Dun Laoghaire, Co Dublin, Ireland Bedford MK41 0YE
Telephone: 01344 858616 Telephone: 353 1 280 3555 Telephone: 01234 229462
Fax: 01344 858758 Fax: 353 1 280 3509 Fax: 01234 229433
Specifications
Product
The tape is based on polyvinyl chloride (PVC) and/or its
copolymers and has a rubber-based, pressure-sensitive
adhesive. The tape shall be 8.5 mils thick, and be UL
Listed and marked per UL Standard 510 as “Flame
Retardant, Cold and Weather Resistant”. The tape must
be applicable at temperatures ranging from -18 C
through 38 C (0 F through 100 F) without loss of
physical properties. The tape shall be classified for use
in both indoor and outdoor environments. The tape shall
be compatible with synthetic cable insulations, jackets
and splicing compounds. The tape will remain stable
and will not telescope more than 0.1 inches when
maintained at temperatures below 50 C (120 F).
Engineering/Architectural Specification
Primary electrical insulation (branch wiring in wet or dry
locations): All splices for 600 volt wire rated 105 C
(220 F) and below shall be insulated with a minimum of
two half-lapped layers of Scotch Super 88 Vinyl
Electrical Tape. All connectors having irregular
surfaces shall be padded with Scotchfil Electrical
Insulation Putty or Scotch 130C Rubber Splicing Tape
prior to insulating with Scotch Super 88 Tape.
Mechanical protection (outer jacketing): All rubber and
thermoplastic insulating high voltage power cable tape
splices and repairs shall be over-wrapped with at least
two half-lapped layers of Scotch Super 88 Vinyl
Electrical Tape.
Installation Techniques
The tape shall be applied in half-lapped layers with
sufficient tension to produce a uniform wind (for most
applications this tension will reduce the tape’s width to
approximately 5/8 of its original width). On pigtail
splices, the tape shall be wrapped beyond the end of the
wires and then folded back, leaving a protective cushion
to resist cut-through. Wrap tape up-hill, taping from a
small diameter surface to a larger diameter surface.
Apply the tape with no tension on the last wrap to
prevent flagging.
Maintenance
Scotch Super 88 Tape complies with the requirements of
UL 510 for storage. When maintained under normal
storage conditions the tape will remain stable and has a
five-year shelf-life.
Important Notice
Technical information provided by 3M is based on experience and/or tests believed to be reliable, but their accuracy is not guaranteed and the results may not be relevant to every
user’s application. For this reason 3M does not accept responsibility or liability, direct or consequential, arising from reliance upon any information provided and the user should
determine the suitability of the products for their intended use. Nothing in this statement will be deemed to exclude or restrict 3M’s liability for death or personal injury arising
from its negligence. All questions of liability relating to 3M products are governed by the seller’s terms of sale subject where applicable to the prevailing law. If any goods
supplied or processed by or on behalf of 3M prove on inspection to be defective in material or workmanship, 3M will (at its option) replace the same or refund to the Buyer the
price paid for the goods or services. Except as set our above, all warranties and conditions, whether express or implied, statutory or otherwise are excluded to the fullest extent
permissible at law.
3M and Scotch are trademarks of the 3M Company. Printed in the UK.
© 3M United Kingdom PLC, 2003.