R1RW0416D Series 4M High Speed SRAM (256-kword x 16-bit) REJ03C0107-0100Z Rev. 1.00 Mar.12.2004 Description The R1RW0416D is a 4-Mbit high speed static RAM organized 256-kword x 16-bit. It has realized high speed access time by employing CMOS process (6-transistor memory cell) and high speed circuit designing technology. It is most appropriate for the application which requires high speed, high density memory and wide bit width configuration, such as cache and buffer memory in system. The R1RW0416D is packaged in 400-mil 44-pin SOJ and 400-mil 44-pin plastic TSOPII for high density surface mounting. Features * Single 3.3 V supply: 3.3 V 0.3 V * Access time: 12 ns (max) * Completely static memory No clock or timing strobe required * Equal access and cycle times * Directly TTL compatible All inputs and outputs * Operating current: 130 mA (max) * TTL standby current: 40 mA (max) * CMOS standby current : 5 mA (max) : 0.8 mA (max) (L-version) * Data retention current: 0.4 mA (max) (L-version) * Data retention voltage: 2.0 V (min) (L-version) * Center VCC and VSS type pin out Rev.1.00, Mar.12.2004, page 1 of 14 R1RW0416D Series Ordering Information Type No. Access time Package R1RW0416DGE-2PR 12 ns 400-mil 44-pin plastic SOJ (44P0K) R1RW0416DGE-2LR 12 ns R1RW0416DSB-2PR 12 ns R1RW0416DSB-2LR 12 ns 400-mil 44-pin plastic TSOPII (44P3W-H) Pin Arrangement 44-pin SOJ A0 A1 A2 A3 A4 CS# I/O1 I/O2 I/O3 I/O4 VCC VSS I/O5 I/O6 I/O7 I/O8 WE# A5 A6 A7 A8 A9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 (Top View) Rev.1.00, Mar.12.2004, page 2 of 14 44-pin TSOP A17 A16 A15 OE# UB# LB# I/O16 I/O15 I/O14 I/O13 VSS VCC I/O12 I/O11 I/O10 I/O9 NC A14 A13 A12 A11 A10 A0 A1 A2 A3 A4 CS# I/O1 I/O2 I/O3 I/O4 VCC VSS I/O5 I/O6 I/O7 I/O8 WE# A5 A6 A7 A8 A9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 (Top View) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A17 A16 A15 OE# UB# LB# I/O16 I/O15 I/O14 I/O13 VSS VCC I/O12 I/O11 I/O10 I/O9 NC A14 A13 A12 A11 A10 R1RW0416D Series Pin Description Pin name Function A0 to A17 Address input I/O1 to I/O16 Data input/output CS# Chip select OE# Output enable WE# Write enable UB# Upper byte select LB# Lower byte select VCC Power supply VSS Ground NC No connection Rev.1.00, Mar.12.2004, page 3 of 14 R1RW0416D Series Block Diagram (LSB) A14 A13 A12 A5 A6 A7 A11 A10 A3 (MSB) A1 VCC Row decoder Memory matrix 1024 rows x 32 columns x 8 blocks x 16 bit (4,194,304 bits) VSS CS I/O1 .. . I/O8 Column I/O Input data control I/O9 .. . I/O16 Column decoder CS (LSB) A8 A9 A17 A15 A16 A0 A2 A4 (MSB) WE# CS# LB# UB# OE# CS Rev.1.00, Mar.12.2004, page 4 of 14 R1RW0416D Series Operation Table CS# OE# WE# LB# UB# Mode VCC current I/O1- -I/O8 I/O9- -I/O16 Ref. cycle H x x x x Standby ISB, ISB1 High-Z High-Z L H H x x Output disable ICC High-Z High-Z L L H L L Read ICC Output Output Read cycle L L H L H Lower byte read ICC Output High-Z Read cycle L L H H L Upper byte read ICC High-Z Output Read cycle L L H H H ICC High-Z High-Z L x L L L Write ICC Input Input Write cycle L x L L H Lower byte write ICC Input High-Z Write cycle L x L H L Upper byte write ICC High-Z Input Write cycle L x L H H High-Z High-Z ICC Note: H: VIH, L: VIL, x: VIH or VIL Absolute Maximum Ratings Parameter Symbol Value Supply voltage relative to VSS VCC -0.5 to +4.6 Voltage on any pin relative to VSS VT -0.5* to VCC + 0.5* Power dissipation PT 1.0 W Operating temperature Topr 0 to +70 C Storage temperature Tstg -55 to +125 C Storage temperature under bias Tbias -10 to +85 C 1 Unit V 2 V Notes: 1. VT (min) = -2.0 V for pulse width (under shoot) 6 ns. 2. VT (max) = VCC + 2.0 V for pulse width (over shoot) 6 ns. Recommended DC Operating Conditions (Ta = 0 to +70C) Parameter Symbol Supply voltage Min Typ Max Unit 3 3.0 3.3 3.6 V 4 0 0 0 VIH 2.0 VCC + 0.5* VIL -0.5* 0.8 VCC* VSS* Input voltage Notes: 1. 2. 3. 4. 1 VIL (min) = -2.0 V for pulse width (under shoot) 6 ns. VIH (max) = VCC + 2.0 V for pulse width (over shoot) 6 ns. The supply voltage with all VCC pins must be on the same level. The supply voltage with all VSS pins must be on the same level. Rev.1.00, Mar.12.2004, page 5 of 14 V 2 V V R1RW0416D Series DC Characteristics (Ta = 0 to +70C, VCC = 3.3 V 0.3 V, VSS = 0 V) Parameter Symbol Min Max Unit Test conditions Input leakage current |ILI| 2 A VIN = VSS to VCC Output leakage current |ILO| 2 A VIN = VSS to VCC Operating power supply current ICC 130 mA Min cycle CS# = VIL, IOUT = 0 mA Other inputs = VIH/VIL Standby power supply current ISB 40 mA Min cycle, CS# = VIH, Other inputs = VIH/VIL ISB1 5 mA f = 0 MHz VCC CS# VCC - 0.2 V, (1) 0 V VIN 0.2 V or (2) VCC VIN VCC - 0.2 V * Output voltage Note: 1 0.8* 1 mA VOL 0.4 V IOL = 8 mA VOH 2.4 V IOH = -4 mA 1. This characteristics is guaranteed only for L-version. Capacitance (Ta = +25C, f = 1.0 MHz) Parameter Input capacitance* 1 Input/output capacitance* Note: 1 Symbol Min Max Unit Test conditions CIN 6 pF VIN = 0 V CI/O 8 pF VI/O = 0 V 1. This parameter is sampled and not 100% tested. Rev.1.00, Mar.12.2004, page 6 of 14 R1RW0416D Series AC Characteristics (Ta = 0 to +70C, VCC = 3.3 V 0.3 V, unless otherwise noted.) Test Conditions * Input pulse levels: 3.0 V/0.0 V * Input rise and fall time: 3 ns * Input and output timing reference levels: 1.5 V * Output load: See figures (Including scope and jig) 3.3 V 1.5 V RL = 50 DOUT Zo = 50 319 DOUT 353 30 pF 5 pF Output load (B) (for tCLZ, tOLZ, tBLZ, tCHZ, tOHZ, tBHZ, tWHZ, and tOW) Output load (A) Read Cycle R1RW0416D -2 Parameter Symbol Min Max Unit Read cycle time tRC 12 ns Address access time tAA 12 ns Chip select access time tACS 12 ns Output enable to output valid tOE 6 ns Byte select to output valid tBA 6 ns Output hold from address change tOH 3 ns Chip select to output in low-Z tCLZ 3 ns 1 Output enable to output in low-Z tOLZ 0 ns 1 Byte select to output in low-Z tBLZ 0 ns 1 Chip deselect to output in high-Z tCHZ 6 ns 1 Output disable to output in high-Z tOHZ 6 ns 1 Byte deselect to output in high-Z tBHZ 6 ns 1 Rev.1.00, Mar.12.2004, page 7 of 14 Notes R1RW0416D Series Write Cycle R1RW0416D -2 Parameter Symbol Min Max Unit Notes Write cycle time tWC 12 ns Address valid to end of write tAW 8 ns Chip select to end of write tCW 8 ns 8 Write pulse width tWP 8 ns 7 Byte select to end of write tBW 8 ns Address setup time tAS 0 ns 5 Write recovery time tWR 0 ns 6 Data to write time overlap tDW 6 ns Data hold from write time tDH 0 ns Write disable to output in low-Z tOW 3 ns 1 Output disable to output in high-Z tOHZ 6 ns 1 Write enable to output in high-Z tWHZ 6 ns 1 Notes: 1. Transition is measured 200 mV from steady voltage with output load (B). This parameter is sampled and not 100% tested. 2. If the CS# or LB# or UB# low transition occurs simultaneously with the WE# low transition or after the WE# transition, output remains a high impedance state. 3. WE# and/or CS# must be high during address transition time. 4. If CS#, OE#, LB# and UB# are low during this period, I/O pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 5. tAS is measured from the latest address transition to the latest of CS#, WE#, LB# or UB# going low. 6. tWR is measured from the earliest of CS#, WE#, LB# or UB# going high to the first address transition. 7. A write occurs during the overlap of a low CS#, a low WE# and a low LB# or a low UB# (tWP). A write begins at the latest transition among CS# going low, WE# going low and LB# going low or UB# going low. A write ends at the earliest transition among CS# going high, WE# going high and LB# going high or UB# going high. 8. tCW is measured from the later of CS# going low to the end of write. Rev.1.00, Mar.12.2004, page 8 of 14 R1RW0416D Series Timing Waveforms Read Timing Waveform (1) (WE# = VIH) t RC Address Valid address tAA tACS CS# tOE tCHZ *1 tBA tOHZ *1 tBLZ *1 tBHZ *1 OE# LB#, UB# tOLZ *1 tOH tCLZ *1 DOUT High impedance *4 Rev.1.00, Mar.12.2004, page 9 of 14 Valid data *4 R1RW0416D Series Read Timing Waveform (2) (WE# = VIH, LB# = VIL, UB# = VIL) tRC Address Valid address tOH tAA tACS tCHZ*1 CS# tOE tOHZ*1 OE# tOLZ*1 tCLZ *1 DOUT High impedance *4 Rev.1.00, Mar.12.2004, page 10 of 14 Valid data *4 R1RW0416D Series Write Timing Waveform (1) (WE# Controlled) tWC Valid address Address tWR tAW tAS tWP WE#*3 tCW CS#*3 OE# tBW LB#, UB# tOLZ tWHZ tOW tOHZ High impedance DOUT *2 DIN Rev.1.00, Mar.12.2004, page 11 of 14 tDW tDH Valid data R1RW0416D Series Write Timing Waveform (2) (CS# Controlled) tWC Valid address Address tWR tAW tAS tWP WE# *3 tCW CS# *3 OE# tBW LB#, UB# tOLZ tWHZ tOW tOHZ High impedance * DOUT *2 DIN Rev.1.00, Mar.12.2004, page 12 of 14 tDW tDH Valid data 4 R1RW0416D Series Write Timing Waveform (3) (LB#, UB# Controlled, OE# = VIH) tWC Address Valid address tAW tWR tWP WE#*3 tCW CS#*3 tAS tBW UB# (LB#) tBW LB# (UB#) tDW DIN-UB (DIN-LB) tDH Valid data tDW DIN-LB (DIN-UB) DOUT Rev.1.00, Mar.12.2004, page 13 of 14 tDH Valid data High impedance R1RW0416D Series Low VCC Data Retention Characteristics (Ta = 0 to +70C) This characteristics is guaranteed only for L-version. Parameter Symbol Min Max Unit Test conditions VCC for data retention VDR 2.0 V VCC CS# VCC - 0.2 V, (1) 0 V VIN 0.2 V or (2) VCC VIN VCC - 0.2 V Data retention current ICCDR 400 A VCC = 3 V VCC CS# VCC - 0.2 V, (1) 0 V VIN 0.2 V or (2) VCC VIN VCC - 0.2 V Chip deselect to data retention time tCDR 0 ns See retention waveform Operation recovery time tR 5 ms Low VCC Data Retention Timing Waveform t CDR Data retention mode V CC 3.0 V V DR 2.0 V CS# 0V Rev.1.00, Mar.12.2004, page 14 of 14 VCC CS# VCC - 0.2 V tR Revision History Rev. Date R1RW0416D Series Data Sheet Contents of Modification Page Description 0.01 Sep. 30, 2003 Initial issue 1.00 Mar.12.2004 Deletion of Preliminary Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 (c) 2003, 2004. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .1.0