LTC4071 Li-Ion/Polymer Shunt Battery Charger System with Low Battery Disconnect Description Features n n n n n n n n n n n Charger Plus Pack Protection in One IC Low Operating Current (550nA) Near Zero Current (<0.1nA) Low Battery Disconnect Function to Protect Batteries from Over-Discharge Pin Selectable Low Battery Disconnect Level: 2.7V or 3.2V 1% Float Voltage Accuracy Over Temperature 50mA Maximum Internal Shunt Current Pin Selectable Float Voltage Options: 4.0V, 4.1V, 4.2V Ultralow Power Pulsed NTC Float Conditioning for Li-Ion/Polymer Protection Suitable for Intermittent, Continuous and Very Low Power Charging Sources High Battery Status Output Thermally Enhanced, Low Profile (0.75mm) 8-Lead (2mm x 3mm) DFN and MSOP Packages Applications n n n n n n Low Capacity, Li-Ion/Polymer Battery Back-Up Thin Film Batteries Energy Scavenging/Harvesting Solar Power Systems with Back-Up Memory Back-Up Embedded Automotive The LTC(R)4071 allows simple charging of Li-Ion/Polymer batteries from very low current, intermittent or continuous charging sources. A near-zero current low battery latching disconnect function protects even the lowest capacity batteries from deep discharge and potentially irreparable damage. The 550nA to 50mA operating current makes charging possible from previously unusable sources. With its low operating current the LTC4071 is well suited to charge low capacity Li-Ion or thin film batteries in energy harvesting applications. The unique architecture of the LTC4071 allows for an extremely simple battery charger solution, requiring just one external resistor. The LTC4071 offers a pin selectable float voltage with 1% accuracy. The integrated thermal battery qualifier extends battery lifetime and improves reliability by automatically reducing the battery float voltage at NTC thermistor temperatures above 40C. The LTC4071 also provides two pin selectable low battery disconnect levels and a high battery status output. The device is offered in two thermally enhanced packages, a compact low profile (0.75mm) 8-lead (2mm x 3mm) DFN and an 8-lead MSOP package. L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application Battery Disconnect I LEAK vs Temperature 100n VIN RIN 10n TO SYSTEM LOAD: VCC NTC VCC 1n BAT ILEAK (A) ADJ LTC4071 1F LBSEL GND VBAT = 2.65V + 100p 10p Li-Ion 1p 4071 TA01a 0.1p -25 0 25 50 75 TEMPERATURE (C) 100 125 4071 TA01b 4071fc 1 LTC4071 Absolute Maximum Ratings (Notes 1, 2) ICC, IBAT..............................................60mA Continuous IBAT................................ 400mA for Single Pulse < 10ms ICC................................-400mA for Single Pulse < 10ms ADJ, NTC, NTCBIAS, HBO Voltages... -0.3V to VCC + 0.3V LBSEL Voltage.............................................. -0.3V to 6V Operating Junction Temperature Range... -40C to 125C Storage Temperature Range................... -65C to 150C Peak Reflow Temperature...................................... 260C Pin Configuration TOP VIEW NTCBIAS 1 NTC 2 ADJ 3 9 GND HBO 4 TOP VIEW 8 VCC 7 BAT 6 GND 5 LBSEL NTCBIAS NTC ADJ HBO DDB PACKAGE 8-LEAD (3mm x 2mm) PLASTIC DFN TJMAX = 125C, JA = 76C/W EXPOSED PAD (PIN 9) IS NOT INTERNALLY CONNECTED, MUST BE SOLDERED TO PCB, GND TO OBTAIN JA 1 2 3 4 8 7 6 5 9 GND VCC BAT GND LBSEL MS8E PACKAGE 8-LEAD PLASTIC MSOP TJMAX = 125C, JA = 40C/W EXPOSED PAD (PIN 9) IS NOT INTERNALLY CONNECTED, MUST BE SOLDERED TO PCB, GND TO OBTAIN JA Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4071EDDB#PBF LTC4071EDDB#TRPBF LFXF 8-Lead (3mm x 2mm) Plastic DFN -40C to 125C LTC4071IDDB#PBF LTC4071IDDB#TRPBF LFXF 8-Lead (3mm x 2mm) Plastic DFN -40C to 125C LTC4071EMS8E#PBF LTC4071EMS8E#TRPBF LTFXG 8-Lead Plastic MSOP -40C to 125C LTC4071IMS8E#PBF LTC4071IMS8E#TRPBF LTFXG 8-Lead Plastic MSOP -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range. Conditions are VNTC = VADJ = VCC, VLBSEL = GND, TA = 25C unless otherwise specified. Current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VFLOAT Programmable Float Voltage 10A ICC 25mA VADJ = 0V, 0C < Temp < 125C VADJ = 0V l 3.96 3.88 4.0 4.0 4.04 4.04 V V VADJ = Float, 0C < Temp < 125C VADJ = Float l 4.06 3.98 4.1 4.1 4.14 4.14 V V VADJ = VCC, 0C < Temp < 125C VADJ = VCC l 4.16 4.07 4.2 4.2 4.24 4.24 V V 50 550 1200 ICCMAX Maximum Shunt Current VCC > VFLOAT l ICCQ VCC Operating Current VHBO Low, ADJ = VCC l mA nA 4071fc 2 LTC4071 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range. Conditions are VNTC = VADJ = VCC, VLBSEL = GND, TJ = 25C unless otherwise specified. Current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 0.01 0.01 25 nA nA 4 6 Low Battery Disconnect ILEAK Battery Disconnect Leakage Current VCC < VBAT = 2.65V RDSON Resistance of VCC - BAT Switch IBAT = -1mA, VHBO High VLBD Low Battery Disconnect l VBAT Falling, IBAT = -1mA, LBSEL = VCC, 0C < Temp < 125C VBAT Falling, IBAT = -1mA, LBSEL = VCC 2.60 2.70 2.79 V l 2.52 2.70 2.79 V 3.05 3.20 3.28 V l 2.95 3.20 3.28 V VBAT Falling, IBAT = -1mA, LBSEL = GND, 0C < Temp < 125C VBAT Falling, IBAT = -1mA, LBSEL = GND VLBC_BAT VLBC_VCC Low Battery Connect Low Battery Connect VBAT Rising, IBAT = -1mA, LBSEL = VCC 2.97 V VBAT Rising, IBAT = -1mA, LBSEL = GND 3.53 V VCC Rising, LBSEL = VCC VCC Rising, LBSEL = GND 3.6 4.19 V V High Battery Status VHBTH HBO Threshold (VFLOAT - VCC) VHBHY Hysteresis VCC Rising l 15 40 75 100 mV mV Status Output: HBO VOL CMOS Output Low ISINK = 1mA, VCC = 3.7V 0.5 VOH CMOS Output High ISOURCE = -0.5mA, ICC = 1.5mA V VCC - 0.6 V Selection Inputs: ADJ, LBSEL VADJ_IL ADJ VIL Input Logic Low Level l VADJ_IH ADJ VIH Input Logic High Level l IADJ(Z) Allowable ADJ Leakage Current in Floating State 0.3 V VCC - 0.3 V l 3 A 250 mV VLBSEL_IL LBSEL VIL Input Logic Low Level l VLBSEL_IH LBSEL VIH Input Logic High Level l 1.4 ILBSEL LBSEL Leakage Current 0 LBSEL VCC l -5 0 5 nA INTC NTC Leakage Current 0V NTC VCC l -5 0 5 nA INTCBIAS Average NTCBIAS Sink Current Pulsed Duty Cycle < 0.002% 30 50 pA NTCTH1 NTC Comparator Falling Thresholds VNTC as Percentage of VNTCBIAS Amplitude 35.5 36.5 38 % 28.0 29.0 30.5 % 21.8 22.8 23.8 % 16.8 17.8 18.8 V NTC NTCTH2 NTCTH3 NTCTH4 NTCHY Hysteresis VFLOAT(NTC) Delta Float Voltage per NTC Comparator Step 30 NTC Falling Below One of the NTCTH Thresholds ADJ = 0V ADJ = Floating ADJ = VCC Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4071 is tested under pulsed load conditions such that TJ TA. The LTC4071E is guaranteed to meet performance specifications for junction temperatures from 0C to 85C. Specifications over the -57 -82 -107 -50 -75 -100 % mV -43 -68 -93 mV mV mV -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC4071I is guaranteed over the full -40C to 125C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operation conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. 4071fc 3 LTC4071 Typical Performance Characteristics TA = 25C, unless otherwise noted. LBD/LBC vs Temperature (LBSEL = GND) LBC vs IBAT LBD/LBC vs Temperature (LBSEL = VCC) 4.3 3.7 4.2 4.0 LBD/LBC (V) 3.7 LBSEL = VCC 3.5 3.8 3.6 3.3 3.4 3.1 3.2 2.9 0.01 0.1 1 10 IBAT (mA) 5.5 LBC_BAT ICC (nA) 4.0 25 50 75 100 2.5 -50 125 1200 1000 800 1000 0 25 50 75 TEMPERATURE (C) 100 0 125 ADJ = VCC LBSEL = VCC NTC = NTCBIAS 4.20 0 0.5 1 1.5 2 2.5 3 100 0 -50 VF vs Temperature LBSEL = VCC NTC = NTCBIAS 25 50 75 TEMPERATURE (C) 100 125 4.120 ADJ = FLOAT 50 75 100 125 4071 G06 4.110 4.105 ADJ = GND -25 0 25 50 75 TEMPERATURE (C) 4071 G07 25 4.115 4.10 3.95 -50 0 ADJ = FLOAT NTC = NTCBIAS LBSEL = VCC ADJ = VCC 4.00 0 -25 Load Regulation 4.125 4.05 -25 600 4071 G05 HBOTH 50 4071 G03 TEMPERATURE (C) VCC (V) HBOHY 125 700 300 -50 3.5 4.0 4.15 150 VF (V) HBOTH/HY (mV) 200 100 400 4071 G04 4.25 75 500 VCC (V) HBO Thresholds vs Temperature 250 50 ADJ = VCC LBSEL = VCC NTC = NTCBIAS HBO LOW 800 200 -25 25 ICCQ vs Temperature 900 400 3.0 -50 0 4071 G02 600 3.5 -25 TEMPERATURE (C) 125C RISING 125C FALLING 25C RISING 25C FALLING -45C RISING -45C FALLING 1400 4.5 LBD ADJ = VCC LBSEL = VCC NTC = NTCBIAS 1600 5.0 LBC_BAT 2.7 ICC vs VCC 1800 RDS(ON) () 0 -25 4071 G01 2000 3.1 LBD TEMPERATURE (C) RDS(ON) vs Temperature 3.3 2.9 3.0 -50 100 LBC_VCC ADJ = VCC NTC = NTCBIAS IBAT = -1mA 3.5 ICCQ (nA) LBC_VCC (V) 3.9 LBC_VCC ADJ = VCC NTC = NTCBIAS IBAT = -1mA LBD/LBC (V) LBSEL = GND 4.1 100 125 4071 G08 4.100 4.095 0 10 20 30 ICC (mA) 40 50 60 4071 G09 4071fc 4 LTC4071 Typical Performance Characteristics MP1 Body Diode 1600 0.7 1400 VCC - VHBO (mV) 0.8 0.6 0.5 0.4 0.3 125C 85C 25C -45C 0.2 0.1 0.1 1 10 IBAT (mA) 1400 LBSEL = VCC NTC = NTCBIAS 900 ADJ = GND VCC = 3.6V 1200 ADJ = VCC 1000 800 600 600 VCC = 4.0V 300 400 200 0 100 0.5 0 1 1.5 2 ISOURCE (mA) 4071 G10 LBSEL VIL / VIH vs Temperature 1200 1 0 2 3 ISINK (mA) 4 5 6 4071 G12 VF vs NTC Temperature ADJ = VCC 4.20 VIH 0 2.5 4071 G11 4.25 4.15 1000 ADJ = FLOAT 4.10 4.05 800 VF (V) VIL/VIH (mV) VIL 600 ADJ = GND 4.00 3.95 3.90 400 3.85 200 3.80 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 3.75 LBSEL = VCC 0 40 20 60 80 NTC TEMPERATURE (C) 4071 G13 NTCBIAS Pulse Width vs Temperature 100 4071 G14 NTCBIAS Period vs Temperature 250 7 6 200 5 PERIOD (SEC) 0 0.01 HBO VOL 1200 LBSEL = VCC 1800 NTC = NTCBIAS VCC = 3.5V LBSEL = GND PULSE WIDTH (s) VCC - VBAT (V) 0.9 HBO VOH 2000 VOL (mV) 1.0 TA = 25C, unless otherwise noted. 150 HBO LOW 100 4 HBO LOW 3 2 50 0 -50 HBO HIGH HBO HIGH -25 0 25 50 1 75 TEMPERATURE (C) 100 125 4071 G15 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 4071 G16 4071fc 5 LTC4071 Pin Functions NTCBIAS (Pin 1): NTC Bias Pin. Connect a resistor from NTCBIAS to NTC, and a thermistor from NTC to GND. Float NTCBIAS when not in use. Minimize parasitic capacitance on this pin. NTC (Pin 2): Input to the Negative Temperature Coefficient Thermistor Monitoring Circuit. The NTC pin connects to a negative temperature coefficient thermistor which is typically co-packaged with the battery to determine the temperature of the battery. If the battery temperature is too high, the float voltage is reduced. Connect a low drift bias resistor from NTCBIAS to NTC and a thermistor from NTC to GND. When not in use, connect NTC to VCC. Minimize parasitic capacitance on this pin. ADJ (Pin 3): Float Voltage Adjust Pin. Connect ADJ to GND to program 4.0V float voltage. Disconnect ADJ to program 4.1V float voltage. Connect ADJ to VCC to program 4.2V float voltage. The float voltage is also adjusted by the NTC thermistor. HBO (Pin 4): High Battery Monitor Output (Active High). HBO is a CMOS output that indicates that the battery is almost fully charged and current is being shunted away from VCC. This pin is driven high when VCC rises to within VHBTH of the effective float voltage, VFLOAT_EFF. The absolute value of this threshold depends on ADJ and NTC both of which affect the float voltage. HBO is driven low when VCC falls by more than (VHBTH + VHBHY) below the effective float voltage. Refer to Table 1 for the effective float voltage. LBSEL (Pin 5): Low Battery Disconnect Select Pin. Connect LBSEL to GND to select a low battery disconnect level of 3.2V, connect LBSEL to VCC to select a low battery disconnect level of 2.7V. Do not float. GND (Pin 6, Exposed Pad Pin 9): Ground. The exposed package pad has no internal electrical connection but must be connected to PCB ground for maximum heat transfer. BAT (Pin 7): Battery Pin. Battery charge current is sourced from VCC through this pin when an external supply is present. BAT supplies current to VCC from this pin when no other source of power is available. If BAT falls below VLBD this pin disconnects the battery from VCC protecting the battery from discharge by the load when no external power supply is present. VCC (Pin 8): Input Supply Pin. Attach system load to this pin. The input supply voltage is regulated to 4.0V, 4.1V, or 4.2V depending on the ADJ pin state (see the ADJ pin description for more detail). This pin can sink up to 50mA in order to keep the voltage regulation within accuracy limits. Decouple to GND with a capacitor, CIN, of at least 0.1F, use a larger decoupling cap to handle high peak load currents. 4071fc 6 LTC4071 Block Diagram VIN VCC LTC4071 ADJ CLK 0.9sec - 7sec SYSTEM LOAD 3-STATE DETECT PULSED DUTY CYCLE = 0.003% 30s - 200s T 10k NTC LBSEL HBO BODY DIODE + - OSC NTCBIAS RNOM 10k RIN MP1 BAT ADC + LBSEL MUST BE TIED TO VCC OR GND + - 1.2V 1.2V + -EA Li-Ion BATTERY MP2 GND 4071 BD Operation The LTC4071 provides a simple, reliable, and high performance battery protection and charging solution by preventing the battery voltage from exceeding a programmed level. Its shunt architecture requires just one resistor from the input supply to charge and protect the battery in a wide range of battery applications. When the input supply is removed and the battery voltage is below the high battery output threshold, the LTC4071 consumes just 550nA from the battery. If the battery voltage falls below the programmable low battery disconnect level, the battery disconnects from VCC, protecting the battery from over-discharge either by the load connected to VCC or from the LTC4071 quiescent current. enough for VCC to reach VLBC_VCC to ensure that MP1 turns on. The user may detect the connected state by observing periodic pulses at the NTCBIAS pin that only occur once VCC has risen above VLBC_VCC, and cease once VCC falls below VLBD. Depending on the capacity of the battery and the input decoupling capacitor, the VCC voltage generally falls to VBAT when MP1 turns on; rather than VBAT rising to VCC. The internal PFET then reconnects the battery to VCC and the charge rate is determined by the input voltage, the battery voltage, and the input resistor: When an input supply is present the battery charges through the body diode of the internal disconnect PFET, MP1, until the battery voltage rises above the lowbattery connect threshold. Select an input voltage large As the battery voltage approaches the float voltage, the LTC4071 shunts current away from the battery thereby reducing the charge current. The LTC4071 can shunt up to 50mA. The shunt current limits the maximum charge current. ICHG = ( VIN - VBAT ) RIN 4071fc 7 LTC4071 Operation In cases where the input supply may be shorted to GND when not supplying power, for example with a solar cell, add a diode in series with RIN to prevent the input from loading the battery. For more information, refer to the photovoltaic charger example in the Applications Information section. Adjustable Float Voltage, VFLOAT A built-in 3-state decoder connected to the ADJ pin provides three programmable float voltages: 4.0V, 4.1V, or 4.2V. The float voltage is programmed to 4.0V when ADJ is tied to GND, 4.1V when ADJ is floating (disconnected), and 4.2V when ADJ is tied to VCC. The state of the ADJ pin (and NTC pins) is sampled for about 36s about once every 1.2 seconds when HBO is high, and when HBO is low the sampling rate reduces to about once every 3.6 seconds with the same duty cycle. If VCC falls below VLBD , the sampling stops. When it is being sampled, the LTC4071 applies a relatively low impedance voltage at the ADJ pin. This technique prevents low level board leakage from corrupting the programmed float voltage. NTC Qualified Float Voltage, VFLOAT(NTC) The NTC pin voltage is compared against an internal resistor divider tied to the NTCBIAS pin. This divider has tap points that are matched to the NTC thermistor resistance/temperature conversion table for a Vishay curve 2 thermistor at temperatures of 40C, 50C, 60C, and 70C. The curve 2 thermistor is also designated by a B25/85 value of 3490. Battery temperature conditioning adjusts the float voltage down to VFLOAT_EFF when the NTC thermistor indicates that the battery temperature is too high. For a 10k curve 2 thermistor and a 10k NTCBIAS resistor, each 10C increase in temperature above 40C causes the float voltage to drop by a fixed amount, VFLOAT(NTC), depending on ADJ. If ADJ is at GND, the float voltage steps down by 50mV for each 10C temperature increment. If ADJ is floating, the step size is 75mV. And if ADJ is at VCC, the step size is 100mV. Refer to Table 1 for the range of VFLOAT_EFF programming. Table 1. NTC Qualified Float Voltage ADJ VFLOAT(NTC) TEMPERATURE VNTC AS % OF NTCBIAS VFLOAT_EFF GND 50mV T < 40C VNTC > 36.5 40C T < 50C 29.0 < VNTC 36.5 50C T < 60C 22.8 < VNTC 29.0 60C T < 70C 17.8 < VNTC 22.8 VNTC 17.8 70C < T 4.000 3.950 3.900 3.850 3.800 Floating 75mV T < 40C VNTC > 36.5 40C T < 50C 29.0 < VNTC 36.5 50C T < 60C 22.8 < VNTC 29.0 60C T < 70C 17.8 < VNTC 22.8 VNTC 17.8 70C < T 4.100 4.025 3.950 3.875 3.800 VCC 100mV T < 40C VNTC > 36.5 40C T < 50C 29.0 < VNTC 36.5 50C T < 60C 22.8 < VNTC 29.0 60C T < 70C 17.8 < VNTC 22.8 VNTC 17.8 70C < T 4.200 4.100 4.000 3.900 3.800 For all ADJ pin settings the lowest float voltage setting is: 3.8V = VFLOAT_MIN = VFLOAT - 4 * VFLOAT(NTC). This occurs at NTC thermistor temperatures above 70C, or if the NTC pin is grounded. To conserve power in the NTCBIAS and NTC resistors, the NTCBIAS pin is sampled at a low duty cycle at the same time that the ADJ pin state is sampled. High Battery Status Output: HBO The HBO pin pulls high when VCC rises to within VHBTH of the programmed float voltage, VFLOAT_EFF, including NTC qualified float voltage adjustments assuming VCC has risen above VLBC_VCC. If VCC drops below the float voltage by more than VHBTH + VHBHY the HBO pin pulls low to indicate that the battery is not at full charge. The input supply current to the LTC4071 drops to less than 550nA (typ) as the LTC4071 no longer shunts current to protect the battery. And the NTCBIAS sample clock slows to conserve power. For example, if the NTC thermistor requires the float voltage to be dropped by 100mV (ADJ = VCC and 0.29*VNTCBIAS < VNTC < 0.36*VNTCBIAS) then the HBO rising threshold is detected when VCC rises past: VFLOAT - VFLOAT(NTC) - VHBTH = 4.2V - 100mV - 40mV = 3.96V. 4071fc 8 LTC4071 Operation Low Battery Disconnect/Connect: LBD/LBC Low Battery Select: LBSEL The low battery disconnect (VLBD) and connect (VLBC) voltage levels are programmed by the LBSEL pin. As shown in the Block Diagram the battery disconnects from VCC by shutting off MP1 when the BAT voltage falls below VLBD. This disconnect function protects Li-Ion batteries from permanent damage due to deep discharge. If the voltage of a Li-Ion cell drops below a certain level, the cell may be permanently damaged. Disconnecting the battery from VCC prevents the load at VCC as well as the LTC4071 quiescent current from further discharging the battery. The low battery discharge cutoff voltage level is programmed by the LBSEL pin. Once disconnected the VCC voltage collapses towards ground. When an input supply is reconnected the battery charges through the internal body diode of MP1. The input supply voltage should be larger than VLBC_VCC to ensure that MP1 is turned on. When the VCC voltage reaches VLBC_VCC , MP1 turns on and connects VCC and BAT. While disconnected, the BAT pin voltage is indirectly sensed through MP1's body diode. Therefore VLBC varies with charge current and junction temperature. Please see the Typical Performance Characteristics section for more information. The LBSEL pin allows the user to trade-off battery runtime and maximum shelf life. A lower battery disconnect threshold maximizes run time by allowing the battery to fully discharge before the disconnect event. Conversely, by increasing the low battery disconnect threshold more capacity remains following the disconnect event which extends the shelf life of the battery. For maximum run time, tie LBSEL to VCC so that the battery disconnects at VCC = 2.7V. For extended shelf life, tie LBSEL to GND so that the battery disconnects at VCC = 3.2V. If a high peak current event is expected, users may temporarily select the lower disconnect threshold. This avoids disconnecting the battery too early when the load works against the battery series resistance and temporarily reduces VCC. 4071fc 9 LTC4071 Applications Information General Charging Considerations The LTC4071 uses a different charging methodology from previous chargers. Most Li-Ion chargers terminate the charging after a period of time. The LTC4071 does not have a discrete charge termination. Extensive measurements on Li-Ion cells show that the cell charge current drops to very low levels with the shunt charge control circuit effectively terminating the charge. For improved battery lifetime choose 4.0V or 4.1V float voltage. The battery disconnect function requires some care in selecting the input supply compliance for charging a battery while powering a load at VCC. The internal battery disconnect switch remains off while charging the battery through the body diode of the internal switch until VCC exceeds VLBC_VCC. If the source voltage compliance is not greater than VLBC_VCC , then the battery will never re-connect to VCC and the system load will not be able to run on battery power. Users may detect that the battery is connected by monitoring the NTCBIAS pin as it will periodically pulse high once VCC has risen above VLBC_VCC, and stops pulsing once VCC falls below VLBD. The simplest application of the LTC4071 is shown in Figure 2. This application requires only an external resistor to program the charge/shunt current. Assume the wall RIN = 162, 0.5W WALL ADAPTER VCC BAT Care must be taken in selecting the input resistor. Power dissipated in RIN under full charge current is given by the following equation: PDISS 2 V WALL - VBAT _ MIN ) ( (12V - 3.2V )2 = = = 0.48W + Li-Ion At this point the power dissipated in the input resistor is 388mW. The LTC4071 can also be used to regulate series-connected battery stacks as illustrated in Figure 3. Here two LTC4071 devices are used to charge two batteries in series. A single resistor sets the maximum charge/shunt current. WALL ADAPTER RIN BATTERY GND 162 The charge current decreases as the battery voltage increases. If the battery voltage is 40mV less than the programmed float voltage the LTC4071 consumes only 550nA of current, and all of the excess input current flows into the battery. As the battery voltage reaches the float voltage, the LTC4071 shunts current from the wall adapter and regulates the battery voltage to VFLOAT = VCC. The more shunt current the LTC4071 sinks, the less charge current the battery gets. Eventually, the LTC4071 shunts all the current flowing through RIN; up to the maximum shunt current. The maximum shunt current in this case, with no NTC adjustment is determined by the input resistor and is calculated as: ( V - VFLOAT ) = (12V - 4.1V ) = 49mA ISHUNT _ MAX = WALL RIN 162 LTC4071 1F RIN VCC BAT LTC4071 4071 F02 1F + Li-Ion Figure 2. Single-Cell Battery Charger GND adapter voltage (VWALL) is 12V and the maximum charge current is calculated as: VCC IMAX _ CHARGE = = ( VWALL - VBAT _ MIN ) RIN (12V - 3.2V ) 162 BATTERY BAT LTC4071 1F + Li-Ion GND BATTERY 4071 F03 = 54mA Figure 3. 2-Cell Battery Charger 4071fc 10 LTC4071 Applications Information The GND pin of the top device is simply connected to the VCC pin of the bottom device. Care must be taken in observing the HBO status output pin of the top device as this signal is no longer ground referenced. Likewise for the control inputs of the top device; tie ADJ and LBSEL of the top device to the local GND or VCC pins. Also, the wall adapter must have a high enough voltage rating to charge both cells. NTC Protection The LTC4071 measures battery temperature with a negative temperature coefficient thermistor thermally coupled to the battery. NTC thermistors have temperature characteristics which are specified in resistance-temperature conversion tables. Internal NTC circuitry protects the battery from excessive heat by reducing the float voltage for each 10C rise in temperature above 40C (assuming a Vishay thermistor with a B25/85 value of 3490). The LTC4071 uses a ratio of resistor values to measure battery temperature. The LTC4071 contains an internal fixed resistor voltage divider from NTCBIAS to GND with four tap points; NTCTH1 -NTCTH4. The voltages at these tap points are periodically compared against the voltage at the NTC pin to measure battery temperature. To conserve power, the battery temperature is measured periodically by biasing the NTCBIAS pin to VCC about once every 1.5 seconds. The voltage at the NTC pin depends on the ratio of NTC thermistor value, RNTC, and a bias resistor, RNOM. Choose RNOM equal to the value of the thermistor at 25C. RNOM is 10k for a Vishay NTHS0402N02N1002F thermistor with a B25/85 value of 3490. RNOM must be connected from NTCBIAS to NTC. The ratio of the NTC pin voltage to the NTCBIAS voltage when it is pulsed to VCC is: RNTC (RNTC + RNOM ) When the thermistor temperature rises, the resistance drops; and the resistor divider between RNOM and the thermistor lowers the voltage at the NTC pin. An NTC thermistor with a different B25/85 value may also be used with the LTC4071. However the temperature trip points are shifted due to the higher negative temperature coefficient of the thermistor. To correct for this difference add a resistor, RFIX, in series with the thermistor to shift the ratio: RFIX + RNTC (RFIX + RNTC + RNOM ) Up to the internal resistive divider tap points: NTCTH1 through NTCTH4. For a 100k thermistor with a B25/85 value of 3950, e.g. NTHS0402N01N1003F, at 70C (with RNOM = 100k) choose RFIX = 3.92k. The temperature trip points are found by looking up the curve 1 thermistor R/T values plus RFIX that correspond to the ratios for NTCTH1 = 36.5%, NTCTH2 = 29%, NTCTH3 = 22.8%, and NTCTH4 = 17.8%. Selecting RFIX = 3.92k results in trip points of 39.9C, 49.4C, 59.2C and 69.6C. Another technique may be used without adding an additional component. Instead decrease RNOM to adjust the NTCTH thresholds for a given R/T thermistor profile. For example, if RNOM = 88.7k (with the same 100k thermistor) then the temperature trip points are 41.0C, 49.8C, 58.5C and 67.3C. When using the NTC features of the LTC4071 it is important to keep in mind that the maximum shunt current increases as the float voltage, VFLOAT_EFF drops with NTC conditioning. Reviewing the single-cell battery charger application with a 12V wall adapter in Figure 2; the input resistor should be increased to 165 such that the maximum shunt current does not exceed 50mA at the lowest possible float voltage due to NTC conditioning, VFLOAT_MIN = 3.8V. Thermal Considerations At maximum shunt current, the LTC4071 may dissipate up to 205mW. The thermal dissipation of the package should be taken into account when operating at maximum shunt current so as not to exceed the absolute maximum junction temperature of the device. With JA of 40C/W, in the MSOP package, at maximum shunt current of 50mA the junction temperature rise is about 8C above ambient. With JA of 76C/W in the DFN package, at maximum shunt current of 50mA the junction temperature rise is about 16C above ambient. The junction temperature, TJ , is calculated depending on ambient temperature, TA, power 4071fc 11 LTC4071 Applications Information dissipation, PD (in W), and JA is the thermal impedance of the package (in C/W): TJ = TA + (PD x JA). The application shown in Figure 4 illustrates how to prevent triggering the low-battery disconnect function under large pulsed loads due to the high ESR of thin-film batteries. VIN RIN FLOAT SYSTEM LOAD CBYPASS ADJ VCC BAT NTCBIAS LTC4071 PULSED ILOAD 10k NTC GND LBSEL T + CBYPASS = Li-Ion 4071 F04 NTHS0402N02N1002F age recovers, as the capacity of the battery should provide roughly 50 hours of use for an equivalent 0.1%*20mA = 20A load. To prevent load pulses from tripping the low battery disconnect, add a decoupling capacitor from VCC to GND. The size of this capacitor can be calculated based on how much margin is required from the LBD threshold as well as the amplitude and pulse width of the load transient. For a 1.0mAh battery with a state-of-charge of 3.8V, the margin from LBD is 600mV with LBSEL tied to GND. For a square-wave load pulse of 20mA with a pulse width of 5ms, the minimum size of the decoupling cap required to hold VCC above LBD is calculated as follows: Figure 4. Adding a Decoupling Capacitor for Large Load Transients Table 2 lists some thin-film batteries, their capacities and their equivalent series resistance. The ESR causes VBAT and VCC to droop as a product of the load current amplitude multiplied by the ESR. This droop may trigger the low-battery disconnect while the battery itself may still have ample capacity. Adding a bypass capacitor to VCC prevents large low duty cycle load transients from pulling down on VCC. 20mA * 5ms = 166.6F 600mV Take care to select a bypass capacitor with low leakage. The LTC4071 can be used to charge a battery to a 4.2V float voltage from an AC line with a bridge rectifier as shown in the simple schematic in Figure 5. In this example, DANGER! HIGH VOLTAGE R1 = 249k R2 = 249k MB4S AC 110V R3 = 249k R4 = 249k P/N CAPACITY RESISTANCE VMIN CYMBET CBC012 12Ah 5k to 10k 3.0V CYMBET CBC050 50Ah 1500 to 3k 3.0V N/A 500Ah 40 3.0V APS-Autec LIR2025 20mAh 0.75 3.0V APS-Autec LIR1025 6mAh 30 2.75V IPS MEC225-1P 0.13mAh 210 to 260 2.1V IPS MEC220-4P 0.4mAh 100 to 120 2.1V IPS MEC201-10P 1.0mAh 34 to 45 2.1V IPS MEC202-25P 2.5mAh 15 to 20 2.1V GM Battery GMB031009 8mAh 10 to 20 2.75V GS NanoTech For example, given a 0.1% duty cycle 5ms load pulse of 20mA and a 1.0mAh IPS MEC201-10P solid-state thin-film battery with an equivalent series resistance of 35, the voltage drop at VCC can be as high as 0.7V while the load is on. However once the load pulse ends, the battery volt- 12 + SYSTEM LOAD Table 2. Low Capacity Li-Ion and Thin-Film Batteries VENDOR - NTC ADJ VCC LTC4071 FLOAT NTCBIAS LBSEL BAT GND + Li-Ion BATTERY 4071 F05 DANGEROUS AND LETHAL POTENTIALS ARE PRESENT IN AC LINE-CONNECTED CIRCUITS! BEFORE PROCEEDING ANY FURTHER, THE READER IS WARNED THAT CAUTION MUST BE USED IN THE CONSTRUCTION, TESTING AND USE OF AC LINE-CONNECTED CIRCUITS. EXTREME CAUTION MUST BE USED IN WORKING WITH AND MAKING CONNECTIONS TO THESE CIRCUITS. ALL TESTING PERFORMED ON AC LINE-CONNECTED CIRCUITS MUST BE DONE WITH AN ISOLATION TRANSFORMER CONNECTED BETWEEN THE AC LINE AND THE CIRCUIT. USERS AND CONSTRUCTORS OF AC LINE-CONNECTED CIRCUITS MUST OBSERVE THIS PRECAUTION WHEN CONNECTING TEST EQUIPMENT TO THE CIRCUIT TO AVOID ELECTRIC SHOCK. Figure 5. 4.2V AC Line Charging, UL Leakage Okay 4071fc LTC4071 Applications Information the four input 249k resistors are sized for acceptable UL leakage in the event that one of the resistors short. Here, the LTC4071 will fully charge the battery from the AC line while meeting the UL specification with 104A of available charge current. A simple photovoltaic (PV) application for the LTC4071 is illustrated in Figure 6. At low VCC voltage, PV current flows to both the system at VCC as well as the battery. DS16003 + - ** + - ** + - ** + - ** SYSTEM LOAD FLOAT Typically, solar cells are inherently limited in current, but this circuit may require a resistor, RIN, in series with the LTC4071 for high current solar cells. Select RIN such that the LTC4071 never needs to shunt more than 50mA. ADJ VCC 1F BAT NTCBIAS LTC4071 The simple schematic in Figure 7 illustrates a complete piezoelectric energy harvesting application using the LTC4071 to charge and protect Li-Ion cells along with the LTC3588-1 to rectify and regulate energy generated from a piezoelectric generator to a fixed 3.3V load. 10k NTC GND When VCC reaches the programmed float voltage (4.1V with ADJ floating) then the LTC4071 shunts excess current not used by the load, limiting VCC to 4.1V and effectively reducing the battery charge current to zero. If the PV cells stop supplying current, the battery supports the load at VCC through the LTC4071. Add a diode in series with the PV cells to prevent reverse leakage of the PV cells from draining the battery. If the battery discharges to the point where VCC falls below VLBD (3.2V with LBSEL tied to GND) the LTC4071 disconnects the load from the battery to protect the battery from over discharge. LBSEL T* + Li-Ion 4071 F06 * NTHS0402N02N1002F ** JAMECO 171061 Figure 6. Simple Photovoltaic Charger MMSD4148T1 15k VCC 22F BAT 1F LTC4071 + Li-Ion BATTERY GND LBSEL PFCB-W14 VCC 1F 10H VOUT + Li-Ion BATTERY LBSEL CAP LTC3588-1 SW BAT LTC4071 GND VIN PZ1 VIN2 PZ2 VIN2 100F D1 D0 GND 3.3V SYSTEM LOAD 4.7F 4071 F07 Figure 7. Piezoelectric Energy Harvester with Battery Backup 4071fc 13 LTC4071 Applications Information This system has two modes of operation, charging where the batteries are being charged from energy harvested from the piezoelectric generator while the load is negligible. And discharging, where the load is pulling current from the batteries, but insufficient energy is being harvested to power the load. This application allows the load to periodically draw more current than would otherwise be available from the piezoelectric generator by storing excess charge in a stack of two Li-Ion cells. Each Li-Ion cell is protected from overcharge and over discharge by a LTC4071 shunt regulator. The two LTC4071s regulate VIN of the LTC3588-1 to 8.2V (with both ADJ pins floating) shunting any excess current that is not used by the load once the batteries achieve their float voltages. When the load requires more current than is available from the piezoelectric generator, the voltage at VIN droops and current is supplied from the two Li-Ion cells to power the step-down switching regulator. If the load pulls enough current to discharge the batteries below VLBD, the LTC4071s disconnect the batteries, and VIN collapses until the piezoelectric generator resumes supplying current. The application in Figure 8 illustrates how to implement "ship-mode," where a battery is co-packaged with the LTC4071 and then the entire device is latched-off, leaving the battery fully charged but with the LTC4071 switched off. The co-packaged battery and LTC4071 can then be stored with a long shelf-life before being activated for normal use. CURRENT PULSE TO TRIGGER SHIP-MODE IPK 0 ADJ 1F LBSEL VCC BAT NTCBIAS LTC4071 10k NTC GND T* + *NTHS0402N02N1002F Li-Ion 4071 F08 Figure 8. LTC4071 Ship-Mode Application for Extended Shelf Life Ship-mode is triggered by pulling enough current through the LTC4071 so as to drop VCC below the LBD threshold. The current pulse amplitude should be less than 400mA with a duration of less than 10ms. The peak current necessary, IPK, depends on the equivalent series resistance of the battery, BESR, summed with the RDSON of the BAT-VCC FET, the battery voltage, VBAT and the selected disconnect voltage, VLBD: IPK = VBAT - VLBD RDSON + BESR Users may test that ship mode has been triggered by simply checking if VCC is at GND and that there are no longer any NTCBIAS pulses. Re-activation of the LTC4071 and the battery requires either applying power normally, or briefly shorting VCC to BAT to turn it on. 4071fc 14 LTC4071 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. DDB Package 8-Lead Plastic DFN (3mm x 2mm) (Reference LTC DWG # 05-08-1702 Rev B) 0.61 0.05 (2 SIDES) 3.00 0.10 (2 SIDES) 0.70 0.05 2.55 0.05 1.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 2.20 0.05 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) 0.200 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS R = 0.115 TYP 5 R = 0.05 TYP 0.40 0.10 8 2.00 0.10 (2 SIDES) 0.56 0.05 (2 SIDES) 0.75 0.05 0 - 0.05 4 0.25 0.05 1 PIN 1 R = 0.20 OR 0.25 x 45 CHAMFER (DDB8) DFN 0905 REV B 0.50 BSC 2.15 0.05 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO VERSION (WECD-1) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4071fc 15 LTC4071 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MS8E Package 8-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1662 Rev I) BOTTOM VIEW OF EXPOSED PAD OPTION 1.88 (.074) 1 1.88 0.102 (.074 .004) 0.29 REF 1.68 (.066) 0.889 0.127 (.035 .005) 0.05 REF 5.23 (.206) MIN DETAIL "B" CORNER TAIL IS PART OF DETAIL "B" THE LEADFRAME FEATURE. FOR REFERENCE ONLY NO MEASUREMENT PURPOSE 1.68 0.102 3.20 - 3.45 (.066 .004) (.126 - .136) 8 3.00 0.102 (.118 .004) (NOTE 3) 0.65 (.0256) BSC 0.42 0.038 (.0165 .0015) TYP 8 7 6 5 0.52 (.0205) REF RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0 - 6 TYP GAUGE PLANE 0.53 0.152 (.021 .006) DETAIL "A" 1 2 3 4 1.10 (.043) MAX 0.86 (.034) REF 0.18 (.007) SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP 0.65 (.0256) BSC 0.1016 0.0508 (.004 .002) MSOP (MS8E) 0910 REV I NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 6. EXPOSED PAD DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD SHALL NOT EXCEED 0.254mm (.010") PER SIDE. 4071fc 16 LTC4071 Revision History REV DATE DESCRIPTION PAGE NUMBER A 10/10 VLBD specification replaced in Electrical Characteristics section. B 4/11 Updated Vishay thermistor part number. C 10/11 Under Note 2, replaced "=" with "". 3 Updated IPS MFR's part numbers. 12 Updated the application example. 12 Updated MFR part number on the Typical Application circuit MEC201-10P. 18 3 11, 12, 13, 14, 18 4071fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 17 LTC4071 Typical Application Typical Application with 100F Bypass Capacitor to Support Large Load Pulse 5V TO 12V 165, 0.5W FLOAT VCC ADJ BAT NTCBIAS 100F PULSED 200mA LOAD 10k LTC4071 NTC GND LBSEL T* LOW DUTY CYCLE SYSTEM LOAD + GMB031009 OR GS NANO OR MEC201-10P *NTHS0402N02N1002F tON = 1ms 4071 TA02 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3105 400mA Step-Up Converter with 250mV Start-Up and Maximum Power Point Control A High Efficiency Step-Up DC/DC Converter That Can Operate from Input Voltage As Low As 200mV. A 250mV Start-Up Capability and Integrated Maximum Power Point Controller (MPPT) Enables Operation Directly from Low Voltage, High Impedance Alternative Power Sources Such As Photovoltaic Cells, Thermoelectric Generators (TEGs) and Fuel Cells. A User Programmable MPPC Set Point Maximizes the Energy That Can Be Extracted from Any Power Source. Burst Mode(R) Operation, with a Proprietary Self Adjusting Peak Current, Optimizes Converter Efficiency and Output Voltage Ripple Over All Operating Conditions. LTC3108/ LTC3108-1 Ultralow Power Step-Up Converter and Power Manager A Highly Integrated DC/DC Converter Ideal for Harvesting and Managing Surplus Energy from Extremely Low Input Voltage Sources Such As TEGs (Thermoelectric Generators), Thermopiles and Small Solar Cells. The Step-Up Topology Operates from Input Sources As Low As 20mV. The LTC3108 is Functionally Equivalent to the LTC3108-1 Except for its Unique Fixed VOUT Options. LTC3388 20V High Efficiency Nanopower Step-Down Regulator High Efficiency Step-Down DC/DC Converter with Internal High Side and Synchronous Power Switches, Draws Only 720nA Typical DC Supply Current at No Load. 50mA of Load Current, Accurate UVLO Disables Converter and Maintains Low Quiescent Current State When the Input Voltage Falls Below 2.3V. 10-Lead MSE and 3mm x 3mm DFN Packages. LTC3588-1 Piezoelectric Energy Harvesting Power Supply in 3mm x 3mm DFN and MSOP Packages High Efficiency Hysteretic Integrated Buck DC/DC; 950nA Input Quiescent Current (Output in Regulation - No Load), 520nA Input Quiescent Current in UVLO, 2.6V to 19.2V Input Operating Range; Integrated Low-Loss Full-Wave Bridge Rectifier, Up to 100mA of Output Current, Selectable Output Voltages of 1.8V, 2.5V, 3.3V or 3.6V. LTC4054L Standalone Linear Li-Ion Battery Charger in ThinSOTTM Low Current Version of LTC4054, 10mA ICHG 150mA, Thermal Regulation Prevents Overheating, C/10 Termination, with Integrated Pass Transistor. LTC4065L Standalone 250mA Li-Ion Battery Charger in 2mm x 2mm DFN Low Current Version of LTC4065, 15mA ICHG 250mA, 4.2V, 0.6% Float Voltage, High Charge Current Accuracy: 5%. LTC4070 Li-Ion/Polymer Shunt Battery Charger System Low 450nA Operating Current, 50mA Maximum Internal Shunt Current, Boostable to 500mA with External PFET 4071fc 18 Linear Technology Corporation LT 1011 REV C * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2010