PC714VxNSZX Series PC714VxNSZX Series DIP 6 pin General Purpose Photocoupler Description Agency approvals/Compliance PC714VxNSZX Series contains an IRED optically coupled to a phototransistor. It is packaged in a 6 pin DIP. Input-output isolation voltage(rms) is 5.0kV. Collector-emitter voltage is 80V(*) and CTR is 50% to 600% at input current of 5mA. 1. Recognized by UL1577 (Double protection isolation), file No. E64380 (as model No. PC714V) 2. Approved by TUV (VDE0884) (as an option) file No. R-9151576 (as model No. PC714V) 3. Package resin : UL flammability grade (94V-0) Applications Features 1. Home appliances 2. Programmable controllers 3. Personal computer peripherals 1. 6 pin DIP package 2. Double transfer mold package (Ideal for Flow Soldering) 3. High collector-emitter voltage (VCEO:80V(*)) 4. High isolation voltage between input and output (Viso(rms) : 5.0kV) (*) Up to Date code "P7" (July 2002) VCEO : 35V. Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D2-A04101EN Date Nov. 28. 2003 (c) SHARP Corporation PC714VxNSZX Series Internal Connection Diagram 1 1 6 2 5 2 3 4 3 4 5 6 Anode Cathode NC Emitter Collector NC Outline Dimensions (Unit : mm) 2. Through-Hole (VDE0884 option) [ex. PC714VxYSZX] 1. Through-Hole [ex. PC714VxNSZX] 1.20.3 1.20.3 0.60.2 0.6 PC714V Anode mark 1 SHARP mark "S" 4 2 3 0.5 5 Date code 4 1 VDE0884 Identification mark 4 PC714V Anode mark 2 3 0.3 Date code 7.12 7.12 7.620.3 7.620.3 Rank mark 2.90.5 0.5TYP. 3.50.5 Rank mark 2.90.5 6 0.5TYP. 5 3.50.5 6 6.50.5 SHARP mark "S" 6.50.5 0.2 Epoxy resin 0.50.1 2.540.25 : 0 to 13 0.50.1 3.250.5 2.540.25 3.250.5 Epoxy resin : 0 to 13 Product mass : approx. 0.36g Sheet No.: D2-A04101EN 2 PC714VxNSZX Series Date code (2 digit) A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M ** N * Mark P R S T U V W X A B C ** * 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D repeats in a 20 year cycle Country of origin Japan Rank mark Refer to the Model Line-up Sheet No.: D2-A04101EN 3 PC714VxNSZX Series Absolute Maximum Ratings Output Input Parameter Symbol Forward current IF *1 Peak forward current IFM Reverse voltage VR Power dissipation P Collector-emitter voltage VCEO Emitter-collector voltage VECO IC Collector current Collector power dissipation PC Ptot Total power dissipation Topr Operating temperature Tstg Storage temperature *2 Isolation voltage Viso (rms) *3 Soldering temperature Tsol Rating 50 1 6 70 *4 80 6 50 150 170 -25 to +100 -40 to +125 5 260 (Ta=25C) Unit mA A V mW V V mA mW mW C C kV C *1 Pulse width100s, Duty ratio : 0.001 *2 40 to 60%RH, AC for 1minute, f=60Hz *3 For 10s *4 Up to Date code "P7" (July 2002) VCEO : 35V. Electro-optical Characteristics Input Output Transfer characteristics Parameter Symbol Forward voltage VF VFM Peak forward voltage IR Reverse current Ct Terminal capacitance ICEO Collector dark current Collector-emitter breakdown voltage BVCEO Emitter-collector breakdown voltage BVECO Current transfer ratio IC Collector-emitter saturation voltage VCE (sat) Isolation resistance RISO Cf Floating capacitance fC Cut-off frequency tr Rise time Response time Fall time tf Conditions IF=20mA IFM=0.5A VR=4V V=0, f=1kHz VCE=50V, IF=0 IC=0.1mA, IF=0 IE=10A, IF=0 IF=5mA, VCE=5V IF=20mA, IC=1mA DC500V, 40 to 60%RH V=0, f=1MHz VCE=5V, IC=2mA, RL=100 -3dB VCE=2V, IC=2mA, RL=100 MIN. - - - - - *5 80 6 2.5 - 5x1010 - - - - TYP. 1.2 - - 30 - - - - 0.1 1x1011 0.6 80 4 3 MAX. 1.4 3.0 10 250 100 - - 30.0 0.2 - 1.0 - 18 18 (Ta=25C) Unit V V A pF nA V V mA V pF kHz s s *5 Up to Date code "P7" (July 2002) BVCEO35V. Sheet No.: D2-A04101EN 4 PC714VxNSZX Series Model Line-up Through-Hole Sleeve Rank mark Package 50pcs/sleeve VDE0884 ------ Approved PC714V0NSZX PC714V0YSZX with or with out A PC714V1NSZX PC714V1YSZX B PC714V2NSZX PC714V2YSZX Model No. PC714V3NSZX PC714V3YSZX C A or B PC714V5NSZX PC714V5YSZX B or C PC714V6NSZX PC714V6YSZX A, B or C PC714V8NSZX PC714V8YSZX Lead Form IC [mA] (IF=5mA, VCE=5V, Ta=25C) 2.5 to 30.0 4.0 to 8.0 6.5 to 13.0 10.0 to 20.0 4.0 to 13.0 6.5 to 20.0 4.0 to 20.0 Please contact a local SHARP sales representative to inquire about production status and Lead-Free options. Sheet No.: D2-A04101EN 5 PC714VxNSZX Series Fig.1 Forward Current vs. Ambient Temperature Fig.2 Diode Power Dissipation vs. Ambient Temperature 60 100 Diode power dissipation P (mW) Forward current IF (mA) 50 40 30 20 10 0 -25 0 25 50 75 100 80 70 60 40 20 0 -25 125 0 Ambient temperature Ta (C) Fig.4 Total Power Dissipation vs. Ambient Temperature Fig.3 Collector Power Dissipation vs. Ambient Temperature 250 Total power dissipation Ptot (mW) Collector power dissipation PC (mW) 200 150 100 50 0 -25 0 25 50 75 100 200 170 150 100 50 0 -25 125 0 Ambient temperature Ta (C) 10 25 50 75 100 Ambient temperature Ta (C) Fig.6 Forward Current vs. Forward Voltage Fig.5 Peak Forward Current vs. Duty Ratio Ta=75C Pulse width100s Ta=25C 50C Forward current IF (mA) Peak forward current IFM (A) 25 55 75 100 Ambient temperature Ta (C) 1 0.1 25C 0C 100 -25C 10 1 0.01 10-3 10-2 10-1 0 1 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Forward voltage VF (V) Duty ratio Sheet No.: D2-A04101EN 6 PC714VxNSZX Series Fig.8 Collector Current vs. Collectoremitter Voltage Fig.7 Current Transfer Ratio vs. Forward Current 30 200 180 Ta=25C 25 160 Collector current IC (mA) Current transfer ratio CTR (%) IF=30mA VCE=5V Ta=25C 140 120 100 80 60 40 PC (MAX.) 20mA 20 15 10mA 10 5mA 5 20 0 0 0 10 1 Fig.9 Relative Current Transfer Ratio vs. Ambient Temperature Collector-emitter saturation voltage VCE(sat) (V) Relative current transfer ratio (%) IF=5mA VCE=5V 100 50 25 50 3 4 5 6 7 8 9 Fig.10 Collector - emitter Saturation Voltage vs. Ambient Temperature 150 0 2 Collector-emitter voltage VCE (V) Forward current IF (mA) 0 -25 1 75 100 0.14 IF=20mA IC=1mA 0.12 0.1 0.08 0.06 0.04 0.02 -25 0 Ambient temperature Ta (C) 20 40 60 80 100 Ambient temperature Ta(C) Fig.11 Collector Dark Current vs. Ambient Temperature Fig.12 Response Time vs. Load Resistance 10-5 VCE=50V 100 10-7 Response time (s) Collector dark current ICEO (A) 10-6 10-8 10-9 VCE=2V IC=2mA Ta=25C tr tf 10 td ts 1 -10 10 10-11 -25 0.1 0 25 50 75 0.1 100 1 10 Load resistance RL (k) Ambient temperature Ta (C) Sheet No.: D2-A04101EN 7 PC714VxNSZX Series Fig.13 Test Circuit for Response Time Fig.14 Frequency Response Input VCC VCE=5V IC=2mA Ta=25C 0 Output RD RL 10% Output VCE Voltage gain Av (dB) Input 90% td ts tr tf Please refer to the conditions in Fig.12 RL=10k -10 1k 100 -20 1 10 100 Frequency f (kHz) Fig.15 Test Circuit for Frequency Response VCC RD RL Output VCE Please refer to the conditions in Fig.14 Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D2-A04101EN 8 PC714VxNSZX Series Design Considerations Design guide While operating at IF<1.0mA, CTR variation may increase. Please make design considering this fact. This product is not designed against irradiation and incorporates non-coherent IRED. Degradation In general, the emission of the IRED used in photocouplers will degrade over time. In the case of long term operation, please take the general IRED degradation (50% degradation over 5years) into the design consideration. For additional design assistance, please review our corresponding Optoelectronic Application Notes. Sheet No.: D2-A04101EN 9 PC714VxNSZX Series Manufacturing Guidelines Soldering Method Flow Soldering : Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. Flow soldering should be completed below 270C and within 10s. Preheating is within the bounds of 100 to 150C and 30 to 80s. Please don't solder more than twice. Hand soldering Hand soldering should be completed within 3s when the point of solder iron is below 400C. Please don't solder more than twice. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. Sheet No.: D2-A04101EN 10 PC714VxNSZX Series Cleaning instructions Solvent cleaning: Solvent temperature should be 45C or below Immersion time should be 3minutes or less Ultrasonic cleaning: The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of PCB and mounting method of the device. Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. Recommended solvent materials: Ethyl alcohol, Methyl alcohol and Isopropyl alcohol In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances:CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. Sheet No.: D2-A04101EN 11 PC714VxNSZX Series Package specification Sleeve package Package materials Sleeve : HIPS (with anti-static material) Stopper : Styrene-Elastomer Package method MAX. 50 pcs. of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers. The product shall be arranged in the sleeve with its anode mark on the tabbed stopper side. MAX. 20 sleeves in one case. Sleeve outline dimensions 12.0 2 5.8 10.8 520 6.7 (Unit : mm) Sheet No.: D2-A04101EN 12 PC714VxNSZX Series Important Notices with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). * The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. * Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. * If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. * Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection * This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. * Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: D2-A04101EN 13