CUSTOMER'S PRODUCT NAME:
DC/AC INVERTER UNIT CXA- P1212D-WJL
TDK PRODUCT NAME:
MESSRS :
DWG.No.
PREPARED BY APPROVED BY AUTHORIZED BY
K.Yamaishi H.Masuoka
CTR-3774-A
N.Suzuki
Product Drawing
TDK-Lambda Corporation
Apr/21/2010 Apr/21/2010Apr/621/2010
*Notice
Product Drawing is not contract. This is only technical data.
This technical data may change internal description without any notice.
When you design final product please request us specification through our sales or distributors.
After you receive the specification, the contract is effective on signature of the specification.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
1
When using this product, give due consideration to the precautionary notes described below
and ensure a safe design. Inappropriate use may result in electric shock, injury or fire.
Caution
Precautionary Notes Regarding the Use of This Inverter
This product is designed for the lighting of a Cold Cathode Fluorescent Lamp.
Do not use it with any other load.
Store this product under the conditions defined in the specification document.
Do not store this product in an environment where dust, dirt or corrosive gas(salt,acid,base, etc.) is present.
This product is subject to high voltage. If there is a possibility that the user may touch the product,
provide a proper indication in order to draw the user's attention.
This product is designed for use with general electronic equipment.
If it is to be used with medical equipment that directly affects human life or for the control of
transportation equipment to which passengers entrust their lives, provide thorough fail-safe measures.
lf this product use for in-vehicle or always vibrated place,please consult us before using.
Avoid using this product under high temperatures or high humidity or in an environment in which
dust, dirt or any corrosive gas (salt,acid,base, etc.) is present.
Also,be careful not to allow the formation of dew condensation. It may result in damage or electric shock.
If the product does not have a built-in protective circuit (circuit breaker, fuse, etc.),
it is recommended that a fuse be used at the input stage to prevent the generation of
smoke or fire in the event of a malfunction.
Even when the product has a built-in protective circuit (circuit breaker, fuse, etc.),
the circuit may not function properly due to inappropriate operating conditions or power-supply capacity.
It is recommended that an appropriate protective circuit (circuit breaker, fuse, etc.)
be provided separately from the built-in circuit.
Use the product only within the specified input voltage, output power, output voltage
and operating temperature ranges. Exceeding these values may result in damage, etc.
Provide a measure for the prevention of surge voltage due to lightning, etc.
Abnormal voltage may result in damage, etc.
To prevent problems arising from short-circuiting of the high-voltage section,
provide appropriate measures to prevent the entry of foreign substances following installation.
This product is not designed to provide resistance to radiation.
Please fix the inverter by using all the mounting holes to protect the inveter against vibration and shock.
Ripples could be superimposed on the voltage and the current in the input source connected to the inverter ,
depending on the impedance in the input source, wiring, etc.
When you select an input source, please check waveforms, etc on the final set.
Warning
This product is subject to high voltage. Do not touch it while the power is on.
Failing to do so may result in electric shock.
Handling Precautions
This product uses thin wires. Observe the following precautions and handle it with care so
as not to cause wire breakage. Broken wire may result in damage, etc.
Do not stack multiple products on top of one another.
Do not allow the product to come in contact with tools, etc.
Do not apply excessive stress during installation.
It may cause chipping and cracking,resulting in damage, etc.
Provide clearance between the high-voltage section of this product and the frame body on which the product
is installed and also the conductor section as per listed on page 2 , [1] ”Outline” .
Please do not use the product, when dropping it, since there is a possibility of the parts damage.
Please confirm abnormality is not found in the product enough when using it by any chance.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
2
[1] Outline
Outline
Connector Configuration
[3] Electrical specifications
[5] Reliability Test
[4] Test Circuit
[2] Absolute Maximum Ratings
[7] Others
Item Attached view Page
[1] section
5
9
8
4～5
6～7
6
3
[1] section
[2] section
[3] section
[4] section
[5] section
[7] section
Others
Std Warranty
2. Contents
1. Part Name
The part name is CXA-P1212D-WJL.
Test Cond.
[6] Packing and Marking [6] section 9
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
3
8.5
max.
(1.0)
L1
CAUTION
HIGH VOLTAGE
CXA-P1212D-WJL
U 9Y01
MADE IN JAPAN
(ii) (i)
153.5max.
2-φ3.5±0.2
(iii)
1
CN1
1
CN2
(10.0)
14±0.3
22max.
3.5±0.5(4.0)
(4.0)
(10.0)
107±0.3
10.25
±0.5
T1
1
TDK-Lambda
1
IC1
75mm
(a:High Voltage generation area)
SIDE VIEW
No parts and pattern area.(Except GND)
SILICONE
Label (Example)
TDK part No, Date code, Country of origin,
TDK-Lambda Logo.
TOP VIEW
BOTTOM VIEW
Unit:mm
Weight:21.3g.typ.
*Please secure the air clearance of 3mm or more from the high voltage generation area up and down and right and left.
Please refer to Note1-3. for details.
[1] Outline
1-1. Outline
QU
1
1
1
REMARK
UL94V-0 t=1.0
MOLEX
JST
No.
(i)
(ii)
(iii)
Part Description
PCB
Input Connector CN1
Output Connector CN2
Material
Composite (CEM-3)
53261-0771
SM03(7-D1)B-BHS-1-TB(LF)(SN)
●Features●
・This inverter is for two lamps. It has Dimmi ng function(PWM System) and Remote function.
・This product has shutdown function.
It prevents from keeping generating the high voltage wh en the lamps open.(Refer Note. 4-4.)
・With lamp failure det ector.
Normal Operation : CN1-6=0V
Some Lamps Open : CN1-6=5V
・Select the way of dimming (between CN1-6 and CN1-7)
1. Insert a potentiometer (0-50kΩ)
2. Apply the voltage (0-2.5V)
・The high-voltage area (terminals and patterns) is coated with silicone so as to avoid the defects caused by dust.
・This product is conformity to RoHS directive.（※）
（※）Conformity to RoHS Directive:This means that, in conformity with EU Directive 2002/95/EC,
lead, cadmium, hexavalent chromium, and specific bromine-based flame retardants, PBB
and PBDE, have not been used,excep t for exempted applications.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
4
1-2. Connector Configuration
Note 1-1. Marking of TDK part No, Date code, Country of origin.
1) TDK part No., Date code, Country of origin, is marked on the bord back side.
2) Date code example. (ex. Dec. 1. 2009)
3) Country of origin code example. (ex. MADE IN JAPAN. MADE IN CHINA. MADE IN MALAYSIA).
0 19 Z
Two digits of production day.
One digit of production month. (Oct. : X, Nov. : Y, Dec. : Z).
Last digit of production year.
Pin No.
CN1-1
CN1-3
CN1-5
CN1-6
CN1-7
Symbols
Vin
GND
Vrmt
Vst
Vbr/Rbr
Ratings
10.8-13.2V
0V
0V/2.5V-Vin
0V / 5V
0-2.5V/0-50kΩ
Input side CN1
CN1-2
CN1-4
Pin No.
CN2-1
CN2-4
Symbols
V
HIGH
1
V
HIGH
2
V
LOW
Notes
Output1
Output1 Return
Output side CN2
CN2-2 Output2
CN2-3 NC -
U
Manufacturing base code
For circuit connection, please prefer to test circuit diagram [4].
Please use minimum of 3mm clearance (all directions) between inverter high voltage area and any
conductors.
Please refer to mechanical drawing for marking of high voltage area.
Open voltage (strike voltage) is measured across the transformer secondary winding at no load as the
reading at
the output connector would be less than the actual value.
Note 1-2.
Note 1-3.
Note 1-4.
Notes
Input Voltage
GND
0-0.4V:OFF
2.5-Vin V:ON
The warning output
5V in abnormal
circumstances
Control/VR
Ratings
600Vrms
(2V)
600Vrms
-
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
5
Figure 1. High voltage wiring
LCD/M LCD/M
OK NG
CN2
CN2
If the start up voltage falls below Cold Cathode Tube strike voltage, the CCFL will not light up easily specially at
lower ambient temperature. Please review mounting instruction to avoid any abnormal operation due to
coupling/leakage capacitance of inverter high voltage are a to any surrounding conductor.
Please check your lamp characteristic for minimum operational current and set the limit point in your design to
avoid flickering and/or abnormal operation.
For proper operation of circuit protection (fuse or IC PROTECTOR),Please use mi nimum of 2.5A capacity for input
power supply.
For proper operation: Don't connect the out put VLOW(CN2-4) terminal to the input GND (CN1-3,4).
Note 1-5.
Note 1-6.
Note 1-7.
Note 1-8.
Note 1-9.
[2]Absolute maximum ratings
Items Symbols Specification Unit Notes
Input Voltage
Load Resistance
Operating Temp. range
Storage Temp. range
Humidity range
Vin
RL//CL
Ta
Ts
RH
0~15
100//7.5
-30~80
-30~85
95
VDC
kΩ // pF
°C
°C
%RH A maximum wet ball temperature is 38°C
No dew.
Vrmt
Vbr 0~16
-1~Vin+1
The test circuits added 7.5pF capacitor across the load resistor for LCD back light stay capacitor.Note 2-1.
Impedance from the power source or connectio n can cause ripple at the input voltage/current.
This products includes an internal fuse rated at 1.25A. Please make sure that the ripple from the input current
does not go above 1.25A.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
6
[3] Electrical specifications
Item
Output Current
(MAX.)
Symbol
lout1/2
Conditions
Vin(V)
12±1.2
12±0.6
Ta(℃)
RL1(kΩ)//CL1(pF)
RL2(kΩ)//CL2(pF)
-30～80
23±5
90// 7.5
90// 7.5
90// 7.5
90// 7.5
Specifications
MIN. MAX.TYP.
5.3
5.5
6.0
6.0
6.7
6.5
Unit
mArms
Vrmt(V) Vbr(V)/
VR(Ω)
5±0.25
5±0.25
0 / 0
0 / 0
12±1.2 90// 7.5
∞
∞
90// 7.5
90// 7.5
90// 7.5
12±1.2
12±1.2
5±0.25
5±0.25
5±0.25
0 / 0
0 / 0
0 / 0
-30～80
-30～80
-30～80
5.5
V5.5
4.5
4.5
5.0
5.0
0 0.5-
Warning Signal
(Note4-4) Vst
Output Current
(MIN.) lout1/2 12±1.2 -30～80 90// 7.5
90// 7.5 1.1 2.0 2.95±0.25 2.5 / 50k
Frequency
Open Circuit Voltage
F1
Vopen 12±1.2
Input Current1 lin1
Input Current2 lin2
-30～80
-30～80 90// 7.5
90// 7.5
∞
∞
38 43 48
1500 2000 Vrms
kHz
1700
-30～80 90// 7.5
90// 7.5 - 0.8 1.0 A
-30～80 90// 7.5
90// 7.5 - - 1 mA
12±0.6
12±0.6
12±0.6
5±0.25
0±0.25
5±0.25
5±0.25
0 / 0
0 / 0
0 / 0
0 / 0
Frequency(Duty) F2 -30～80 90// 7.5
90// 7.5 220 250 280 Hz12±0.6 5±0.25 2.5 / 50k
[4] Test circuit
RL1,2:Load resistance (7W MIN.)
CL1,2:Stray capacitor (3kV MIN.)
*For the number of the component's positon, please refer to Outline diagram [1].
Vbr
0～2.5V
A
V
1000:1
PROBE
V
Vin
10.8～13.2V
Iin Vopen
F
CN1-1
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
F
V
a
b
SW1
Vrmt
5V
V
Vst
a
b
SW2
Rbr
0～50kΩ
V
T1-2 T1-7,8
T1
A A
RL2 RL1
Io2 Io1
CN2-
1
CN2-4
CN2-
2
SW3
SW4
SW5
CL2 CL1
～
～ ～
Fduty
1
78
14
IC
F
(0.025W MIN.)
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
7
Vrmt terminal circuit (Reference)
20kΩ
10kΩ
CN1-5
Vrmt
IC1
CN1-1,2
Vin
10kΩ
10kΩ
10kΩ
10kΩ
*Vbr=0V:brightness MAX.
Rbr=0Ω:brightness MAX.
Note 4-1.SW1 (ON/OFF) Operation is as following;
SW1
a
b
Operation
Non operation
Non operationOpen
Operation of unit
Note 4-2.SW2 (ON/OFF) Operation is as f ollowing;
SW2
a
b
*Variable resistance dimming
VR=0~50k
*Voltage dimming
Vbr=0~2.5V
Operation of unit
Ω
Note 4-3.Test Equipments Note 4-4.Safety Function
Load Condition
Normal Operation
1 Lamp Open
2 Lamps Open
*1
Alarm Signal
(CN1-6)
0.5V max.
4.5~5.5V
4.5~5.5V
*2
Shutdown
Operation
Normal
Normal
Shutdown
Connection diagram of LCD module (Reference)
V
HIGH
V
HIGH
V
LOW
A
DC-AC inverterLCD module
Lamp
Lamp
*Connect the High Frequency Current Meter to the Low-Voltage (V
LOW
) side.
A
V
A
V
Digital Multiple Meter(ADVANTEST R6452A or equivalent)
DC Current Meter(ADVANTEST R6452A or equivalent)
True RMS Meter(NF Circuit M2170or equivalent)
High Frequency Current Meter(FLUKE187or equivalent)
1000:1
High Voltage Probe(Tektronix P6015A or equivalent)
~
~
F
Frequency Countor(ADVANTEST R6452A or equivalent)
*1.When any of the load is opened, the alarm output
becomes 5V.
*2.When all of the load is open ed, inverter will shut
down about 3 seconds.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
8
[5] Reliability test
Following test items are assured.
Items Conditions
-30°C 500h
-20°C 500h
Load cond.:TYP
85°C 500h
70°C 500h
Load cond.:TYP
Heat shock
Humidity
(Non operational)
Vibration
Shock
-30°C to 80°C
30min.Each 100 Cycles
60°C 90~95%RH 500h
10~57Hz Amplitude 0.75mm
58~500Hz 9.8m/s
2
Sweep:11min
60min each axis X,Y,Z
980m/s
2
11ms
Harf-sine pulse
1 time each axis ±X,Y,Z
Judgement
Low Temp.Non
operational
Low Temp.operational
High Temp.Non
operational
High Temp.operational
Electrical and apperrance should be in the
spec.
No. MATERIALS NAME MATERIAL REMARK
PRODUCT NAME or MODEL,TITLE
DC-AC INVERTER UNIT CXA-P1212D-WJL
PAGENAME OF DRAWING DRAWING No.
Product Drawing CTR-3774-A
TDK-Lambda
QU
<The drawings may be changed without any notice.>
9
[6] Packing and Marking
A shipping box is packaged to avoid from water o r damage. Following items are printed on the box.
[7] Others
7-1. Test cond.
7-2. Std warrantry
7-3. Others
A normal test condition :Temperature (20±15°C), Humidity (65±20%RH).
One year after shipment.This covers any defects in material or workmanship.
Defective units will be replaces at no charge.
TDK and customer are to discuss changes,problems, and modifications and etc, when needed.
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
TDK part No.
Manufacture
Customer part No.
QTY.
Inspection No.
Country of origin
CXA-P1212D-WJL
10pcs / box
Inner box
(237mm:L)×(223mm:W)×(40mm:H)
Marking
TDK Part No.
Manufacture
Customer Part No.
QTY.
Inspection No.
Countory of origin
Outer carton
(500mm:L)×(244mm:W)×(234mm:H)
10pcs/Inner box × 10
＝100pcs/Outer carton
Anti static bag
Marking
TDK Part No.
Manufacture
Customer Part No.
QTY.
Inspection No.
Countory of origin
