Order this document by 2N6071/D SEMICONDUCTOR TECHNICAL DATA Silicon Bidirectional Thyristors *Motorola preferred devices . . . designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied anode voltage with positive or negative gate triggering. TRIACs 4 AMPERES RMS 200 thru 600 VOLTS * Sensitive Gate Triggering (A and B versions) Uniquely Compatible for Direct Coupling to TTL, HTL, CMOS and Operational Amplifier Integrated Circuit Logic Functions * Gate Triggering 2 Mode -- 2N6071, 2N6073, 2N6075 4 Mode -- 2N6071,A,B, 2N6073,A,B, 2N6075,A,B * Blocking Voltages to 600 Volts * All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability * Small, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability MT1 MT2 G MT2 G MT2 MT1 CASE 77-08 (TO-225AA) STYLE 5 MAXIMUM RATINGS (TJ = 25C unless otherwise noted.) Rating *Peak Repetitive Off-State Voltage(1) (Gate Open, TJ = 25 to 110C) Symbol Value VDRM *Peak Surge Current (One Full cycle, 60 Hz, TJ = -40 to +110C) Circuit Fusing Considerations (t = 8.3 ms) *Peak Gate Power *Average Gate Power *Peak Gate Voltage Volts 200 400 600 2N6071,A,B 2N6073,A,B 2N6075,A,B *On-State Current RMS (TC = 85C) Unit IT(RMS) 4 Amps ITSM 30 Amps I2t 3.7 A2s PGM 10 Watts PG(AV) 0.5 Watt VGM 5 Volts *Indicates JEDEC Registered Data. 1. VDRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Preferred devices are Motorola recommended choices for future use and best overall value. Motorola Thyristor Device Data Motorola, Inc. 1995 1 MAXIMUM RATINGS Rating *Operating Junction Temperature Range *Storage Temperature Range Mounting Torque (6-32 Screw)(1) Symbol Value Unit TJ -40 to +110 C Tstg -40 to +150 C -- 8 in. lb. *Indicates JEDEC Registered Data. 1. Torque rating applies with use of compression washer (B52200F006). Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heatsink contact pad are common. For soldering purposes (either terminal connection or device mounting), soldering temperatures shall not exceed +200C, for 10 seconds. Consult factory for lead bending options. THERMAL CHARACTERISTICS Characteristic Symbol Max Unit *Thermal Resistance, Junction to Case RJC 3.5 C/W Thermal Resistance, Junction to Ambient RJA 75 C/W *Indicates JEDEC Registered Data. ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted.) Characteristic Symbol *Peak Blocking Current (VD = Rated VDRM, gate open, TJ = 25C) (TJ = 110C) IDRM *On-State Voltage (Either Direction) (ITM = 6 A Peak) VTM *Peak Gate Trigger Voltage (Continuous dc) (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms, TJ = -40C) MT2(+), G(+); MT2(-), G(-) All Types MT2(+), G(-); MT2(-), G(+) 2N6071,A,B, 2N6073,A,B 2N6075,A,B (Main Terminal Voltage = Rated VDRM, RL = 10 k ohms, TJ = 110C) MT2(+), G(+); MT2(-), G(-) All Types MT2(+), G(-); MT2(-), G(+) 2N6071,A,B, 2N6073,A,B, 2N6075,A,B VGT *Holding Current (Either Direction) (Main Terminal Voltage = 12 Vdc, Gate Open, TJ = -40C) (Initiating Current = 1 Adc) 2N6071, 2N6073, 2N6075, 2N6071A,B, 2N6073A,B, 2N6075A,B (TJ = 25C) 2N6071, 2N6073, 2N6075 2N6071A,B, 2N6073A,B, 2N6075A,B IH Turn-On Time (Either Direction) (ITM = 14 Adc, IGT = 100 mAdc) Blocking Voltage Application Rate at Commutation @ VDRM, TJ = 85C, Gate Open, ITM = 5.7 A, Commutating di/dt = 2.0 A/ms Min Typ Max Unit -- -- -- -- 10 2 A mA -- -- 2 Volts Volts -- -- 1.4 1.4 2.5 2.5 0.2 0.2 -- -- -- -- mA -- -- -- -- -- -- -- -- 70 30 30 15 ton -- 1.5 -- s dv/dt(c) -- 5 -- V/s *Indicates JEDEC Registered Data. 2 Motorola Thyristor Device Data QUADRANT (See Definition Below) IGT @ TJ I mA II mA III mA IV mA 2N6071 2N6073 2N6075 +25C 30 -- 30 -- -40C 60 -- 60 -- 2N6071A 2N6073A 2N6075A +25C 5 5 5 10 -40C 20 20 20 30 2N6071B 2N6073B 2N6075B +25C 3 3 3 5 -40C 15 15 15 20 Type Gate Trigger Current (Continuous dc) (Main Terminal Voltage = 12 Vdc, RL = 100 ohms) Maximum Value *Indicates JEDEC Registered Data. SAMPLE APPLICATION: TTL-SENSITIVE GATE 4 AMPERE TRIAC TRIGGERS IN MODES II AND III 14 0V MC7400 4 7 VEE = 5.0 V + -VEE 1. Consistent predictable turn-on points. 2. Simplified circuitry. 3. Fast turn-on time for cooler, more efficient and reliable operation. MT2(+) QUADRANT I MT2(+), G(-) MT2(+), G(+) 115 VAC 60 Hz Trigger devices are recommended for gating on Triacs. They provide: QUADRANT DEFINITIONS QUADRANT II LOAD 2N6071A 510 For 2N6071, 2N6073, 2N6075 ELECTRICAL CHARACTERISTICS of RECOMMENDED BIDIRECTIONAL SWITCHES Usage G(-) Part Number G(+) QUADRANT III QUADRANT IV MT2(-), G(-) General MT2(-), G(+) MBS4991 MBS100 VS 6.0 - 10 V 7.5 - 9.0 V 3.0 - 5.0 V IS 350 A Max 250 A Max 100 - 400 A VS1 - VS2 0.5 V Max 0.2 V Max 0.35 V Max Temperature Coefficient MT2(-) MBS4993 Lamp Dimmer 0.02%/C Typ SENSITIVE GATE LOGIC REFERENCE IC Logic Functions Firing Quadrant II III TTL 2N6071A Series 2N6071A Series HTL 2N6071A Series 2N6071A Series CMOS (NAND) I 2N6071B Series CMOS (Buffer) Operational Amplifier Zero Voltage Switch Motorola Thyristor Device Data IV 2N6071B Series 2N6071B Series 2N6071B Series 2N6071A Series 2N6071A Series 2N6071A Series 2N6071A Series 3 FIGURE 1 - AVERAGE CURRENT DERATING FIGURE 2 - RMS CURRENT DERATING 110 110 = 30 TC , CASE TEMPERATURE ( C) TC , CASE TEMPERATURE ( C) 60 100 = 30 60 90 90 120 180 dc 80 70 = CONDUCTION ANGLE 120 90 180 80 = CONDUCTION ANGLE 0 4.0 FIGURE 4 - POWER DISSIPATION 8.0 8.0 180 6.0 P(AV) , AVERAGE POWER (WATTS) P(AV) , AVERAGE POWER (WATTS) dc 120 = CONDUCTION ANGLE 90 60 4.0 = 30 2.0 0 dc 6.0 = 180 = CONDUCTION ANGLE 120 4.0 30 2.0 60 90 0 0 1.0 2.0 3.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP) 4.0 0 3.0 OFF-STATE VOLTAGE = 12 Vdc ALL MODES 2.0 1.0 0.7 0.5 0.3 -60 -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) 120 1.0 2.0 3.0 IT(RMS), RMS ON-STATE CURRENT (AMP) 4.0 FIGURE 6 - TYPICAL GATE-TRIGGER CURRENT I GTM , GATE TRIGGER CURRENT (NORMALIZED) FIGURE 5 - TYPICAL GATE-TRIGGER VOLTAGE VGTM , GATE TRIGGER VOLTAGE (NORMALIZED) 4.0 1.0 2.0 3.0 IT(RMS), RMS ON-STATE CURRENT (AMP) FIGURE 3 - POWER DISSIPATION 4 dc 70 3.0 1.0 2.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP) 0 90 100 140 3.0 OFF-STATE VOLTAGE = 12 Vdc ALL MODES 2.0 1.0 0.7 0.5 0.3 -60 -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) 120 140 Motorola Thyristor Device Data FIGURE 7 - MAXIMUM ON-STATE CHARACTERISTICS FIGURE 8 - TYPICAL HOLDING CURRENT 40 IH, HOLDING CURRENT (NORMALIZED) 3.0 30 20 10 ITM , ON-STATE CURRENT (AMP) 7.0 5.0 2.0 1.0 0.7 0.5 0.3 -60 TJ = 110C 3.0 GATE OPEN APPLIES TO EITHER DIRECTION -40 -20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) 2.0 TJ = 25C FIGURE 9 - MAXIMUM ALLOWABLE SURGE CURRENT 1.0 34 32 PEAK SINEWAVE CURRENT (AMP) 0.7 0.5 0.3 0.2 30 28 26 24 TJ = -40 to +110C f = 60 Hz 22 20 18 16 0.1 0 1.0 2.0 3.0 4.0 5.0 14 1.0 2.0 4.0 5.0 7.0 10 NUMBER OF FULL CYCLES VTM, ON-STATE VOLTAGE (VOLTS) Z JC(t), TRANSIENT THERMAL IMPEDANCE (C/W) 3.0 FIGURE 10 - THERMAL RESPONSE 10 5.0 MAXIMUM 3.0 2.0 TYPICAL 1.0 0.5 0.3 0.2 0.1 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 1.0 k 2.0 k 5.0 k 10 k t, TIME (ms) Motorola Thyristor Device Data 5 PACKAGE DIMENSIONS -B- U F Q -A- C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. M 1 2 3 H STYLE 5: PIN 1. MT 1 2. MT 2 3. GATE K J V G R 0.25 (0.010) S A M M B M D 2 PL 0.25 (0.010) M A M B DIM A B C D F G H J K M Q R S U V INCHES MIN MAX 0.425 0.435 0.295 0.305 0.095 0.105 0.020 0.026 0.115 0.130 0.094 BSC 0.050 0.095 0.015 0.025 0.575 0.655 5 _ TYP 0.148 0.158 0.045 0.055 0.025 0.035 0.145 0.155 0.040 --- MILLIMETERS MIN MAX 10.80 11.04 7.50 7.74 2.42 2.66 0.51 0.66 2.93 3.30 2.39 BSC 1.27 2.41 0.39 0.63 14.61 16.63 5 _ TYP 3.76 4.01 1.15 1.39 0.64 0.88 3.69 3.93 1.02 --- M CASE 77-08 (TO-225AA) Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 6 Motorola Thyristor Device Data *2N6071/D* 2N6071/D