M95320-W M95320-R M95320-DF 32-Kbit serial SPI bus EEPROM with high-speed clock Datasheet - production data Features Compatible with the Serial Peripheral Interface (SPI) bus Memory array - 32 Kb (4 Kbytes) of EEPROM - Page size: 32 bytes SO8 (MN) 150 mil width Write - Byte Write within 5 ms - Page Write within 5 ms Additional Write lockable page (Identification page) Write Protect: quarter, half or whole memory array High-speed clock: 20 MHz Single supply voltage: - 2.5 V to 5.5 V for M95320-W - 1.8 V to 5.5 V for M95320-R - 1.7 V to 5.5 V for M95320-DF Operating temperature range: from -40C up to +85C Enhanced ESD protection More than 4 million Write cycles More than 200-year data retention Packages - RoHS compliant and halogen-free (ECOPACK(R)) November 2012 This is information on a product in full production. Doc ID 5711 Rev 15 TSSOP8 (DW) 169 mil width UFDFPN8 2 x 3 mm (MLP) 1/46 www.st.com 1 Contents M95320-W M95320-R M95320-DF Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 3.1 Serial Data Output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2 Serial Data Input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.3 Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.4 Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.5 Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.6 Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.7 VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.8 VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Connecting to the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.1 5 SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1 Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1.1 6 5.1.2 Operating supply voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1.3 Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1.4 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.2 Active Power and Standby Power modes . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.3 Hold condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.4 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.5 Data protection and protocol control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2 Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.3 Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.3.1 2/46 WIP bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.3.2 WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.3.3 BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.3.4 SRWD bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.4 Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.5 Read from Memory Array (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.6 Write to Memory Array (WRITE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.6.1 7 Contents Cycling with Error Correction Code (ECC) . . . . . . . . . . . . . . . . . . . . . . 25 6.7 Read Identification Page (available only in M95320-D devices) . . . . . . . . 26 6.8 Write Identification Page (available only in M95320-D devices) . . . . . . . . 27 6.9 Read Lock Status (available only in M95320-D devices) . . . . . . . . . . . . . 28 6.10 Lock ID (available only in M95320-D devices) . . . . . . . . . . . . . . . . . . . . . 29 Power-up and delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.1 Power-up state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.2 Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 8 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 9 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 10 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 11 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Doc ID 5711 Rev 15 3/46 List of tables M95320-W M95320-R M95320-DF List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. 4/46 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Write-protected block size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 M95320-D instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Address range bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Status Register format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Operating conditions (M95320-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Operating conditions (M95320-R, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Operating conditions (M95320-DF, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Cycling performance by groups of four bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Memory cell data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 DC characteristics (M95320-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 DC characteristics (M95320-R, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 DC characteristics (M95320-DF, device grade 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 AC characteristics (M95320-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 AC characteristics (M95320-R, M95320-DF, device grade 6) . . . . . . . . . . . . . . . . . . . . . . 38 SO8N - 8-lead plastic small outline, 150 mils body width, mechanical data . . . . . . . . . . . 41 TSSOP8 - 8-lead thin shrink small outline, package mechanical data. . . . . . . . . . . . . . . . 42 UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 8-pin package connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bus master and memory devices on the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SPI modes supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Hold condition activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Write Enable (WREN) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Write Disable (WRDI) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Read Status Register (RDSR) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Write Status Register (WRSR) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Read from Memory Array (READ) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Byte Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Page Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Read Identification Page sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Write identification page sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Read Lock Status sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Lock ID sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Serial input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Serial output timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SO8N - 8-lead plastic small outline, 150 mils body width, package outline . . . . . . . . . . . . 41 TSSOP8 - 8-lead thin shrink small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . 42 UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat no lead, package outline. . . . . . . 43 Doc ID 5711 Rev 15 5/46 Description 1 M95320-W M95320-R M95320-DF Description The M95320 devices are Electrically Erasable PROgrammable Memories (EEPROMs) organized as 4096 x 8 bits, accessed through the SPI bus. The M95320 devices can operate with a supply range from 1.7 V up to 5.5 V, and are guaranteed over the -40 C/+85 C temperature range. The M95320-D offers an additional page, named the Identification Page (32 bytes). The Identification Page can be used to store sensitive application parameters which can be (later) permanently locked in Read-only mode. Figure 1. Logic diagram VCC D Q C S M95xxx W HOLD VSS AI01789C The SPI bus signals are C, D and Q, as shown in Figure 1 and Table 1. The device is selected when Chip Select (S) is driven low. Communications with the device can be interrupted when the HOLD is driven low. Table 1. Signal names Signal name 6/46 Function Direction C Serial Clock Input D Serial Data Input Input Q Serial Data Output Output S Chip Select Input W Write Protect Input HOLD Hold Input VCC Supply voltage VSS Ground Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Figure 2. Description 8-pin package connections (top view) M95xxx S Q W VSS 1 2 3 4 8 7 6 5 VCC HOLD C D AI01790D 1. See Section 10: Package mechanical data section for package dimensions, and how to identify pin 1. Doc ID 5711 Rev 15 7/46 Memory organization 2 M95320-W M95320-R M95320-DF Memory organization The memory is organized as shown in the following figure. Figure 3. Block diagram (/,$ 7 3 (IGH VOLTAGE GENERATOR #ONTROL LOGIC # $ 1 )/ SHIFT REGISTER !DDRESS REGISTER AND COUNTER $ATA REGISTER 3TATUS REGISTER 9 DECODER 3IZE OF THE 2EAD ONLY %%02/AREA PAGE )DENTIFICATION PAGE 8 DECODER -36 8/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 3 Signal description Signal description During all operations, VCC must be held stable and within the specified valid range: VCC(min) to VCC(max). All of the input and output signals must be held high or low (according to voltages of VIH, VOH, VIL or VOL, as specified in Section 9: DC and AC parameters). These signals are described next. 3.1 Serial Data Output (Q) This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of Serial Clock (C). 3.2 Serial Data Input (D) This input signal is used to transfer data serially into the device. It receives instructions, addresses, and the data to be written. Values are latched on the rising edge of Serial Clock (C). 3.3 Serial Clock (C) This input signal provides the timing of the serial interface. Instructions, addresses, or data present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on Serial Data Output (Q) change from the falling edge of Serial Clock (C). 3.4 Chip Select (S) When this input signal is high, the device is deselected and Serial Data Output (Q) is at high impedance. The device is in the Standby Power mode, unless an internal Write cycle is in progress. Driving Chip Select (S) low selects the device, placing it in the Active Power mode. After power-up, a falling edge on Chip Select (S) is required prior to the start of any instruction. 3.5 Hold (HOLD) The Hold (HOLD) signal is used to pause any serial communications with the device without deselecting the device. During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data Input (D) and Serial Clock (C) are Don't Care. To start the Hold condition, the device must be selected, with Chip Select (S) driven low. Doc ID 5711 Rev 15 9/46 Signal description 3.6 M95320-W M95320-R M95320-DF Write Protect (W) The main purpose of this input signal is to freeze the size of the area of memory that is protected against Write instructions (as specified by the values in the BP1 and BP0 bits of the Status Register). This pin must be driven either high or low, and must be stable during all Write instructions. 3.7 VCC supply voltage VCC is the supply voltage. 3.8 VSS ground VSS is the reference for all signals, including the VCC supply voltage. 10/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 4 Connecting to the SPI bus Connecting to the SPI bus All instructions, addresses and input data bytes are shifted in to the device, most significant bit first. The Serial Data Input (D) is sampled on the first rising edge of the Serial Clock (C) after Chip Select (S) goes low. All output data bytes are shifted out of the device, most significant bit first. The Serial Data Output (Q) is latched on the first falling edge of the Serial Clock (C) after the instruction (such as the Read from Memory Array and Read Status Register instructions) have been clocked into the device. Figure 4. Bus master and memory devices on the SPI bus VSS VCC R SDO SPI Interface with (CPOL, CPHA) = (0, 0) or (1, 1) SDI SCK VCC C Q D SPI Bus Master SPI Memory Device R CS3 VCC C Q D VSS C Q D VCC VSS SPI Memory Device R VSS SPI Memory Device R CS2 CS1 S W HOLD S W HOLD S W HOLD AI12836b 1. The Write Protect (W) and Hold (HOLD) signals should be driven, high or low as appropriate. Figure 4 shows an example of three memory devices connected to an SPI bus master. Only one memory device is selected at a time, so only one memory device drives the Serial Data Output (Q) line at a time. The other memory devices are high impedance. The pull-up resistor R (represented in Figure 4) ensures that a device is not selected if the Bus Master leaves the S line in the high impedance state. In applications where the Bus Master may leave all SPI bus lines in high impedance at the same time (for example, if the Bus Master is reset during the transmission of an instruction), the clock line (C) must be connected to an external pull-down resistor so that, if all inputs/outputs become high impedance, the C line is pulled low (while the S line is pulled high): this ensures that S and C do not become high at the same time, and so, that the tSHCH requirement is met. The typical value of R is 100 k.. Doc ID 5711 Rev 15 11/46 Connecting to the SPI bus 4.1 M95320-W M95320-R M95320-DF SPI modes These devices can be driven by a microcontroller with its SPI peripheral running in either of the following two modes: CPOL=0, CPHA=0 CPOL=1, CPHA=1 For these two modes, input data is latched in on the rising edge of Serial Clock (C), and output data is available from the falling edge of Serial Clock (C). The difference between the two modes, as shown in Figure 5, is the clock polarity when the bus master is in Stand-by mode and not transferring data: C remains at 0 for (CPOL=0, CPHA=0) C remains at 1 for (CPOL=1, CPHA=1) Figure 5. SPI modes supported CPOL CPHA 0 0 C 1 1 C D MSB Q MSB AI01438B 12/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Operating features 5 Operating features 5.1 Supply voltage (VCC) 5.1.1 Operating supply voltage VCC Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage within the specified [VCC(min), VCC(max)] range must be applied (see Operating conditions in Section 9: DC and AC parameters). This voltage must remain stable and valid until the end of the transmission of the instruction and, for a Write instruction, until the completion of the internal write cycle (tW). In order to secure a stable DC supply voltage, it is recommended to decouple the VCC line with a suitable capacitor (usually of the order of 10 nF to 100 nF) close to the VCC/VSS device pins. 5.1.2 Device reset In order to prevent erroneous instruction decoding and inadvertent Write operations during power-up, a power-on-reset (POR) circuit is included. At power-up, the device does not respond to any instruction until VCC reaches the POR threshold voltage. This threshold is lower than the minimum VCC operating voltage (see Operating conditions in Section 9: DC and AC parameters). At power-up, when VCC passes over the POR threshold, the device is reset and is in the following state: in Standby Power mode, deselected, Status Register values: - The Write Enable Latch (WEL) bit is reset to 0. - The Write In Progress (WIP) bit is reset to 0. - The SRWD, BP1 and BP0 bits remain unchanged (non-volatile bits). It is important to note that the device must not be accessed until VCC reaches a valid and stable level within the specified [VCC(min), VCC(max)] range, as defined under Operating conditions in Section 9: DC and AC parameters. 5.1.3 Power-up conditions When the power supply is turned on, VCC rises continuously from VSS to VCC. During this time, the Chip Select (S) line is not allowed to float but should follow the VCC voltage. It is therefore recommended to connect the S line to VCC via a suitable pull-up resistor (see Figure 4). In addition, the Chip Select (S) input offers a built-in safety feature, as the S input is edgesensitive as well as level-sensitive: after power-up, the device does not become selected until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select (S) must have been high, prior to going low to start the first operation. The VCC voltage has to rise continuously from 0 V up to the minimum VCC operating voltage defined under Operating conditions in Section 9: DC and AC parameters, and the rise time must not vary faster than 1 V/s. Doc ID 5711 Rev 15 13/46 Operating features 5.1.4 M95320-W M95320-R M95320-DF Power-down During power-down (continuous decrease of the VCC supply voltage below the minimum VCC operating voltage defined under Operating conditions in Section 9: DC and AC parameters), the device must be: 5.2 deselected (Chip Select S should be allowed to follow the voltage applied on VCC), in Standby Power mode (there should not be any internal write cycle in progress). Active Power and Standby Power modes When Chip Select (S) is low, the device is selected, and in the Active Power mode. The device consumes ICC. When Chip Select (S) is high, the device is deselected. If a Write cycle is not currently in progress, the device then goes into the Standby Power mode, and the device consumption drops to ICC1, as specified in DC characteristics (see Section 9: DC and AC parameters). 5.3 Hold condition The Hold (HOLD) signal is used to pause any serial communications with the device without resetting the clocking sequence. To enter the Hold condition, the device must be selected, with Chip Select (S) low. During the Hold condition, the Serial Data Output (Q) is high impedance, and the Serial Data Input (D) and the Serial Clock (C) are Don't Care. Normally, the device is kept selected for the whole duration of the Hold condition. Deselecting the device while it is in the Hold condition has the effect of resetting the state of the device, and this mechanism can be used if required to reset any processes that had been in progress.(a)(b) Figure 6. Hold condition activation c HOLD Hold condition Hold condition ai02029E The Hold condition starts when the Hold (HOLD) signal is driven low when Serial Clock (C) is already low (as shown in Figure 6). a. This resets the internal logic, except the WEL and WIP bits of the Status Register. b. In the specific case where the device has shifted in a Write command (Inst + Address + data bytes, each data byte being exactly 8 bits), deselecting the device also triggers the Write cycle of this decoded command. 14/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Operating features The Hold condition ends when the Hold (HOLD) signal is driven high when Serial Clock (C) is already low. Figure 6 also shows what happens if the rising and falling edges are not timed to coincide with Serial Clock (C) being low. 5.4 Status Register The Status Register contains a number of status and control bits that can be read or set (as appropriate) by specific instructions. See Section 6.3: Read Status Register (RDSR) for a detailed description of the Status Register bits. 5.5 Data protection and protocol control The device features the following data protection mechanisms: Before accepting the execution of the Write and Write Status Register instructions, the device checks whether the number of clock pulses comprised in the instructions is a multiple of eight. All instructions that modify data must be preceded by a Write Enable (WREN) instruction to set the Write Enable Latch (WEL) bit. The Block Protect (BP1, BP0) bits in the Status Register are used to configure part of the memory as read-only. The Write Protect (W) signal is used to protect the Block Protect (BP1, BP0) bits in the Status Register. For any instruction to be accepted, and executed, Chip Select (S) must be driven high after the rising edge of Serial Clock (C) for the last bit of the instruction, and before the next rising edge of Serial Clock (C). Two points should be noted in the previous sentence: The "last bit of the instruction" can be the eighth bit of the instruction code, or the eighth bit of a data byte, depending on the instruction (except for Read Status Register (RDSR) and Read (READ) instructions). The "next rising edge of Serial Clock (C)" might (or might not) be the next bus transaction for some other device on the SPI bus. Table 2. Write-protected block size Status Register bits Protected block Protected array addresses 0 none none 0 1 Upper quarter 0C00h - 0FFFh 1 0 Upper half 0800h - 0FFFh 1 1 Whole memory 0000h - 0FFFh BP1 BP0 0 Doc ID 5711 Rev 15 15/46 Instructions 6 M95320-W M95320-R M95320-DF Instructions Each instruction starts with a single-byte code, as summarized in Table 4. If an invalid instruction is sent (one not contained in Table 4), the device automatically deselects itself. Table 3. Instruction set Instruction Description Instruction format WREN Write Enable 0000 0110 WRDI Write Disable 0000 0100 RDSR Read Status Register 0000 0101 WRSR Write Status Register 0000 0001 READ Read from Memory Array 0000 0011 WRITE Write to Memory Array 0000 0010 Table 4. M95320-D instruction set Instruction Instruction format Description WREN Write Enable 0000 0110 WRDI Write Disable 0000 0100 RDSR Read Status Register 0000 0101 WRSR Write Status Register 0000 0001 READ Read from Memory Array 0000 0011 WRITE Write to Memory Array 0000 0010 Read Identification Reads the page dedicated to identification. Page 1000 0011(1) Write Identification Writes the page dedicated to identification. Page 1000 0010(1) Read Lock Status Reads the lock status of the Identification Page. 1000 0011(2) Lock ID Locks the Identification page in read-only mode. 1000 0010(2) 1. Address bit A10 must be 0, all other address bits are Don't Care. 2. Address bit A10 must be 1, all other address bits are Don't Care. Table 5. Address range bits A11-A0(1) Address significant bits 1. Upper MSBs are Don't Care. 16/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.1 Instructions Write Enable (WREN) The Write Enable Latch (WEL) bit must be set prior to each WRITE and WRSR instruction. The only way to do this is to send a Write Enable instruction to the device. As shown in Figure 7, to send this instruction to the device, Chip Select (S) is driven low, and the bits of the instruction byte are shifted in, on Serial Data Input (D). The device then enters a wait state. It waits for the device to be deselected, by Chip Select (S) being driven high. Figure 7. Write Enable (WREN) sequence S 0 1 2 3 4 5 6 7 C Instruction D High Impedance Q AI02281E Doc ID 5711 Rev 15 17/46 Instructions 6.2 M95320-W M95320-R M95320-DF Write Disable (WRDI) One way of resetting the Write Enable Latch (WEL) bit is to send a Write Disable instruction to the device. As shown in Figure 8, to send this instruction to the device, Chip Select (S) is driven low, and the bits of the instruction byte are shifted in, on Serial Data Input (D). The device then enters a wait state. It waits for a the device to be deselected, by Chip Select (S) being driven high. The Write Enable Latch (WEL) bit, in fact, becomes reset by any of the following events: Power-up WRDI instruction execution WRSR instruction completion WRITE instruction completion. Figure 8. Write Disable (WRDI) sequence S 0 1 2 3 4 5 6 7 C Instruction D High Impedance Q AI03750D 18/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.3 Instructions Read Status Register (RDSR) The Read Status Register (RDSR) instruction is used to read the Status Register. The Status Register may be read at any time, even while a Write or Write Status Register cycle is in progress. When one of these cycles is in progress, it is recommended to check the Write In Progress (WIP) bit before sending a new instruction to the device. It is also possible to read the Status Register continuously, as shown in Figure 9. Figure 9. Read Status Register (RDSR) sequence S 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C Instruction D Status Register Out Status Register Out High Impedance Q 7 6 5 4 3 2 1 0 MSB 7 6 5 4 3 2 1 0 7 MSB AI02031E The status and control bits of the Status Register are as follows: 6.3.1 WIP bit The Write In Progress (WIP) bit indicates whether the memory is busy with a Write or Write Status Register cycle. When set to 1, such a cycle is in progress, when reset to 0, no such cycle is in progress. 6.3.2 WEL bit The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch. When set to 1, the internal Write Enable Latch is set. When set to 0, the internal Write Enable Latch is reset, and no Write or Write Status Register instruction is accepted. The WEL bit is returned to its reset state by the following events: 6.3.3 Power-up Write Disable (WRDI) instruction completion Write Status Register (WRSR) instruction completion Write (WRITE) instruction completion BP1, BP0 bits The Block Protect (BP1, BP0) bits are non volatile. They define the size of the area to be software-protected against Write instructions. These bits are written with the Write Status Register (WRSR) instruction. When one or both of the Block Protect (BP1, BP0) bits is set to 1, the relevant memory area (as defined in Table 2) becomes protected against Write (WRITE) instructions. The Block Protect (BP1, BP0) bits can be written provided that the Hardware Protected mode has not been set. Doc ID 5711 Rev 15 19/46 Instructions 6.3.4 M95320-W M95320-R M95320-DF SRWD bit The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W) signal enable the device to be put in the Hardware Protected mode (when the Status Register Write Disable (SRWD) bit is set to 1, and Write Protect (W) is driven low). In this mode, the non-volatile bits of the Status Register (SRWD, BP1, BP0) become read-only bits and the Write Status Register (WRSR) instruction is no longer accepted for execution. Table 6. Status Register format b7 b0 SRWD 0 0 0 BP1 BP0 WEL WIP Status Register Write Protect Block Protect bits Write Enable Latch bit Write In Progress bit 6.4 Write Status Register (WRSR) The Write Status Register (WRSR) instruction is used to write new values to the Status Register. Before it can be accepted, a Write Enable (WREN) instruction must have been previously executed. The Write Status Register (WRSR) instruction is entered by driving Chip Select (S) low, followed by the instruction code, the data byte on Serial Data input (D) and Chip Select (S) driven high. Chip Select (S) must be driven high after the rising edge of Serial Clock (C) that latches in the eighth bit of the data byte, and before the next rising edge of Serial Clock (C). Otherwise, the Write Status Register (WRSR) instruction is not executed. The instruction sequence is shown in Figure 10. Figure 10. Write Status Register (WRSR) sequence S 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C Instruction Status Register In 7 D High Impedance 6 5 4 3 2 1 0 MSB Q AI02282D 20/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Instructions Driving the Chip Select (S) signal high at a byte boundary of the input data triggers the selftimed Write cycle that takes tW to complete (as specified in AC tables under Section 9: DC and AC parameters). While the Write Status Register cycle is in progress, the Status Register may still be read to check the value of the Write in progress (WIP) bit: the WIP bit is 1 during the self-timed Write cycle tW, and 0 when the Write cycle is complete. The WEL bit (Write Enable Latch) is also reset at the end of the Write cycle tW. The Write Status Register (WRSR) instruction enables the user to change the values of the BP1, BP0 and SRWD bits: The Block Protect (BP1, BP0) bits define the size of the area that is to be treated as read-only, as defined in Table 2. The SRWD (Status Register Write Disable) bit, in accordance with the signal read on the Write Protect pin (W), enables the user to set or reset the Write protection mode of the Status Register itself, as defined in Table 7. When in Write-protected mode, the Write Status Register (WRSR) instruction is not executed. The contents of the SRWD and BP1, BP0 bits are updated after the completion of the WRSR instruction, including the tW Write cycle. The Write Status Register (WRSR) instruction has no effect on the b6, b5, b4, b1, b0 bits in the Status Register. Bits b6, b5, b4 are always read as 0. Table 7. Protection modes W SRWD signal bit 1 0 0 0 1 0 1 1 Mode Write protection of the Status Register Memory content Protected area(1) Unprotected area(1) Status Register is writable (if the WREN Software- instruction has set the protected WEL bit). (SPM) The values in the BP1 and BP0 bits can be changed. Write-protected Ready to accept Write instructions Status Register is Hardware writeHardwareprotected. protected The values in the BP1 (HPM) and BP0 bits cannot be changed. Write-protected Ready to accept Write instructions 1. As defined by the values in the Block Protect (BP1, BP0) bits of the Status Register. See Table 2. The protection features of the device are summarized in Table 7. When the Status Register Write Disable (SRWD) bit in the Status Register is 0 (its initial delivery state), it is possible to write to the Status Register (provided that the WEL bit has previously been set by a WREN instruction), regardless of the logic level applied on the Write Protect (W) input pin. Doc ID 5711 Rev 15 21/46 Instructions M95320-W M95320-R M95320-DF When the Status Register Write Disable (SRWD) bit in the Status Register is set to 1, two cases should be considered, depending on the state of the Write Protect (W) input pin: If Write Protect (W) is driven high, it is possible to write to the Status Register (provided that the WEL bit has previously been set by a WREN instruction). If Write Protect (W) is driven low, it is not possible to write to the Status Register even if the WEL bit has previously been set by a WREN instruction. (Attempts to write to the Status Register are rejected, and are not accepted for execution). As a consequence, all the data bytes in the memory area, which are Software-protected (SPM) by the Block Protect (BP1, BP0) bits in the Status Register, are also hardware-protected against data modification. Regardless of the order of the two events, the Hardware-protected mode (HPM) can be entered by: either setting the SRWD bit after driving the Write Protect (W) input pin low, or driving the Write Protect (W) input pin low after setting the SRWD bit. Once the Hardware-protected mode (HPM) has been entered, the only way of exiting it is to pull high the Write Protect (W) input pin. If the Write Protect (W) input pin is permanently tied high, the Hardware-protected mode (HPM) can never be activated, and only the Software-protected mode (SPM), using the Block Protect (BP1, BP0) bits in the Status Register, can be used. 6.5 Read from Memory Array (READ) As shown in Figure 11, to send this instruction to the device, Chip Select (S) is first driven low. The bits of the instruction byte and address bytes are then shifted in, on Serial Data Input (D). The address is loaded into an internal address register, and the byte of data at that address is shifted out, on Serial Data Output (Q). Figure 11. Read from Memory Array (READ) sequence S 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 C Instruction 16-Bit Address 15 14 13 D 3 2 1 0 MSB Data Out 1 High Impedance 7 Q 6 5 4 3 2 Data Out 2 1 0 7 MSB AI01793D 1. Depending on the memory size, as shown in Table 5, the most significant address bits are Don't Care. If Chip Select (S) continues to be driven low, the internal address register is incremented automatically, and the byte of data at the new address is shifted out. 22/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Instructions When the highest address is reached, the address counter rolls over to zero, allowing the Read cycle to be continued indefinitely. The whole memory can, therefore, be read with a single READ instruction. The Read cycle is terminated by driving Chip Select (S) high. The rising edge of the Chip Select (S) signal can occur at any time during the cycle. The instruction is not accepted, and is not executed, if a Write cycle is currently in progress. 6.6 Write to Memory Array (WRITE) As shown in Figure 12, to send this instruction to the device, Chip Select (S) is first driven low. The bits of the instruction byte, address byte, and at least one data byte are then shifted in, on Serial Data Input (D). The instruction is terminated by driving Chip Select (S) high at a byte boundary of the input data. The self-timed Write cycle, triggered by the Chip Select (S) rising edge, continues for a period tW (as specified in AC characteristics in Section 9: DC and AC parameters), at the end of which the Write in Progress (WIP) bit is reset to 0. Figure 12. Byte Write (WRITE) sequence S 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 C Instruction 16-Bit Address 15 14 13 D 3 2 Data Byte 1 0 7 6 5 4 3 2 1 0 High Impedance Q AI01795D 1. Depending on the memory size, as shown in Table 5, the most significant address bits are Don't Care. In the case of Figure 12, Chip Select (S) is driven high after the eighth bit of the data byte has been latched in, indicating that the instruction is being used to write a single byte. However, if Chip Select (S) continues to be driven low, as shown in Figure 13, the next byte of input data is shifted in, so that more than a single byte, starting from the given address towards the end of the same page, can be written in a single internal Write cycle. Each time a new data byte is shifted in, the least significant bits of the internal address counter are incremented. If more bytes are sent than will fit up to the end of the page, a condition known as "roll-over" occurs. In case of roll-over, the bytes exceeding the page size are overwritten from location 0 of the same page. Doc ID 5711 Rev 15 23/46 Instructions M95320-W M95320-R M95320-DF The instruction is not accepted, and is not executed, under the following conditions: Note: if the Write Enable Latch (WEL) bit has not been set to 1 (by executing a Write Enable instruction just before), if a Write cycle is already in progress, if the device has not been deselected, by driving high Chip Select (S), at a byte boundary (after the eighth bit, b0, of the last data byte that has been latched in), if the addressed page is in the region protected by the Block Protect (BP1 and BP0) bits. The self-timed write cycle tW is internally executed as a sequence of two consecutive events: [Erase addressed byte(s)], followed by [Program addressed byte(s)]. An erased bit is read as "0" and a programmed bit is read as "1". Figure 13. Page Write (WRITE) sequence S 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 C Instruction 16-Bit Address 15 14 13 D 3 2 Data Byte 1 1 0 7 6 5 4 3 2 0 1 S 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 C Data Byte 2 D 7 6 5 4 3 2 Data Byte 3 1 0 7 6 5 4 3 2 Data Byte N 1 0 6 5 4 3 2 1 0 AI01796D 1. Depending on the memory size, as shown in Table 5, the most significant address bits are Don't Care. 24/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.6.1 Instructions Cycling with Error Correction Code (ECC) M95320-D devices offer an Error Correction Code (ECC) logic. The ECC is an internal logic function which is transparent for the SPI communication protocol. The ECC logic is implemented on each group of four EEPROM bytes(c). Inside a group, if a single bit out of the four bytes happens to be erroneous during a Read operation, the ECC detects this bit and replaces it with the correct value. The read reliability is therefore much improved. Even if the ECC function is performed on groups of four bytes, a single byte can be written/cycled independently. In this case, the ECC function also writes/cycles the three other bytes located in the same group(c). As a consequence, the maximum cycling budget is defined at group level and the cycling can be distributed over the four bytes of the group: the sum of the cycles seen by byte0, byte1, byte2 and byte3 of the same group must remain below the maximum value defined in Table 14. c. A group of four bytes is located at addresses [4*N, 4*N+1, 4*N+2, 4*N+3], where N is an integer. Doc ID 5711 Rev 15 25/46 Instructions 6.7 M95320-W M95320-R M95320-DF Read Identification Page (available only in M95320-D devices) The Identification Page (32 bytes) is an additional page which can be written and (later) permanently locked in Read-only mode. Reading this page is achieved with the Read Identification Page instruction (see Table 4). The Chip Select signal (S) is first driven low, the bits of the instruction byte and address bytes are then shifted in, on Serial Data Input (D). Address bit A10 must be 0, upper address bits are Don't Care, and the data byte pointed to by the lower address bits [A4:A0] is shifted out on Serial Data Output (Q). If Chip Select (S) continues to be driven low, the internal address register is automatically incremented, and the byte of data at the new address is shifted out. The number of bytes to read in the ID page must not exceed the page boundary, otherwise unexpected data is read (e.g.: when reading the ID page from location 10d, the number of bytes should be less than or equal to 22d, as the ID page boundary is 32 bytes). The read cycle is terminated by driving Chip Select (S) high. The rising edge of the Chip Select (S) signal can occur at any time during the cycle. The first byte addressed can be any byte within any page. The instruction is not accepted, and is not executed, if a write cycle is currently in progress. Figure 14. Read Identification Page sequence 3 # )NSTRUCTION BIT ADDRESS $ -3" $ATA /UT (IGH IMPEDANCE 1 $ATA /UT -3" !I 26/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.8 Instructions Write Identification Page (available only in M95320-D devices) The Identification Page (32 bytes) is an additional page which can be written and (later) permanently locked in Read-only mode. Writing this page is achieved with the Write Identification Page instruction (see Table 4). The Chip Select signal (S) is first driven low. The bits of the instruction byte, address bytes, and at least one data byte are then shifted in on Serial Data Input (D). Address bit A10 must be 0, upper address bits are Don't Care, the lower address bits [A4:A0] address bits define the byte address inside the identification page. The instruction sequence is shown in Figure 15. Figure 15. Write identification page sequence 3 # )NSTRUCTION $ BIT ADDRESS $ATA BYTE (IGH IMPEDANCE 1 -36 Doc ID 5711 Rev 15 27/46 Instructions 6.9 M95320-W M95320-R M95320-DF Read Lock Status (available only in M95320-D devices) The Read Lock Status instruction (see Table 4) is used to check whether the Identification Page is locked or not in Read-only mode. The Read Lock Status sequence is defined with the Chip Select (S) first driven low. The bits of the instruction byte and address bytes are then shifted in on Serial Data Input (D). Address bit A10 must be 1, all other address bits are Don't Care. The Lock bit is the LSB (least significant bit) of the byte read on Serial Data Output (Q). It is at "1" when the lock is active and at "0" when the lock is not active. If Chip Select (S) continues to be driven low, the same data byte is shifted out. The read cycle is terminated by driving Chip Select (S) high. The instruction sequence is shown in Figure 16. Figure 16. Read Lock Status sequence 3 # )NSTRUCTION BIT ADDRESS $ -3" $ATA /UT (IGH IMPEDANCE 1 $ATA /UT -3" !I 28/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 6.10 Instructions Lock ID (available only in M95320-D devices) The Lock ID instruction permanently locks the Identification Page in read-only mode. Before this instruction can be accepted, a Write Enable (WREN) instruction must have been executed. The Lock ID instruction is issued by driving Chip Select (S) low, sending the instruction code, the address and a data byte on Serial Data Input (D), and driving Chip Select (S) high. In the address sent, A10 must be equal to 1, all other address bits are Don't Care. The data byte sent must be equal to the binary value xxxx xx1x, where x = Don't Care. Chip Select (S) must be driven high after the rising edge of Serial Clock (C) that latches in the eighth bit of the data byte, and before the next rising edge of Serial Clock (C). Otherwise, the Lock ID instruction is not executed. Driving Chip Select (S) high at a byte boundary of the input data triggers the self-timed write cycle whose duration is tW (as specified in AC characteristics in Section 9: DC and AC parameters). The instruction sequence is shown in Figure 17. The instruction is discarded, and is not executed, under the following conditions: If a Write cycle is already in progress, If the Block Protect bits (BP1,BP0) = (1,1), If a rising edge on Chip Select (S) happens outside of a byte boundary. Figure 17. Lock ID sequence 3 # )NSTRUCTION BIT ADDRESS $ $ATA BYTE (IGH IMPEDANCE 1 !I Doc ID 5711 Rev 15 29/46 Power-up and delivery state M95320-W M95320-R M95320-DF 7 Power-up and delivery state 7.1 Power-up state After power-up, the device is in the following state: Standby power mode, deselected (after power-up, a falling edge is required on Chip Select (S) before any instructions can be started), not in the Hold condition, the Write Enable Latch (WEL) is reset to 0, Write In Progress (WIP) is reset to 0. The SRWD, BP1 and BP0 bits of the Status Register are unchanged from the previous power-down (they are non-volatile bits). 7.2 Initial delivery state The device is delivered with all the memory array bits and Identification page bits set to 1 (each byte contains FFh). 30/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 8 Maximum rating Maximum rating Stressing the device outside the ratings listed in Table 8 may cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions outside those indicated in the operating sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 8. Absolute maximum ratings Symbol TSTG TLEAD Parameter Min. Max. Unit Ambient operating temperature -40 130 C Storage temperature -65 150 C Lead temperature during soldering See note (1) C VO Output voltage -0.50 VCC+0.6 V VI Input voltage -0.50 6.5 V VCC Supply voltage -0.50 6.5 V IOL DC output current (Q = 0) 5 mA IOH DC output current (Q = 1) 5 mA 4000 V VESD Electrostatic discharge voltage (human body model)(2) 1. Compliant with JEDEC Std J-STD-020 (for small body, Sn-Pb or Pb assembly), with the ST ECOPACK(R) 7191395 specification, and with the European directive on Restrictions on Hazardous Substances (RoHS) 2002/95/EU. 2. Positive and negative pulses applied on different combinations of pin connections, according to AECQ100-002 (compliant with JEDEC Std JESD22-A114, C1=100 pF, R1=1500 , R2=500 ). Doc ID 5711 Rev 15 31/46 DC and AC parameters 9 M95320-W M95320-R M95320-DF DC and AC parameters This section summarizes the operating conditions and the DC/AC characteristics of the device. Table 9. Operating conditions (M95320-W, device grade 6) Symbol VCC TA Table 10. Parameter Min. Max. Unit Supply voltage 2.5 5.5 V Ambient operating temperature -40 85 C Min. Max. Unit Supply voltage 1.8 5.5 V Ambient operating temperature -40 85 C Min. Max. Unit Supply voltage 1.7 5.5 V Ambient operating temperature -40 85 C Max. Unit Operating conditions (M95320-R, device grade 6) Symbol VCC TA Table 11. Parameter Operating conditions (M95320-DF, device grade 6) Symbol VCC TA Table 12. Parameter AC measurement conditions Symbol CL Parameter Load capacitance Min. 30 Input rise and fall times pF 25 ns Input pulse voltages 0.2 VCC to 0.8 VCC V Input and output timing reference voltages 0.3 VCC to 0.7 VCC V Figure 18. AC measurement I/O waveform )NPUT VOLTAGE LEVELS 6## )NPUT AND OUTPUT TIMING REFERENCE LEVELS 6## 6## 6## !)# 32/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF Table 13. Capacitance Symbol COUT CIN DC and AC parameters Test conditions(1) Parameter Max. Unit VOUT = 0 V 8 pF Input capacitance (D) VIN = 0 V 8 pF Input capacitance (other pins) VIN = 0 V 6 pF Output capacitance (Q) Min. 1. Sampled only, not 100% tested, at TA = 25 C and a frequency of 5 MHz. Table 14. Symbol Ncycle Cycling performance by groups of four bytes Parameter(1) Test conditions Write cycle endurance(2) Min. Max. TA 25 C, VCC(min) < VCC < VCC(max) 4,000,000 TA = 85 C, VCC(min) < VCC < VCC(max) 1,200,000 Unit Write cycle(3) 1. Cycling performance for products identified by process letter K. 2. The Write cycle endurance is defined for groups of four data bytes located at addresses [4*N, 4*N+1, 4*N+2, 4*N+3] where N is an integer. The Write cycle endurance is defined by characterization and qualification. 3. A Write cycle is executed when either a Page Write, a Byte Write, a WRSR, a WRID or an LID instruction is decoded. When using the Byte Write, the Page Write or the WRID instruction, refer also to Section 6.6.1: Cycling with Error Correction Code (ECC). Table 15. Memory cell data retention Parameter Data retention(1) Test conditions TA = 55 C Min. Unit 200 Year 1. For products identified by process letter K. The data retention behavior is checked in production. The 200year limit is defined from characterization and qualification results. Doc ID 5711 Rev 15 33/46 DC and AC parameters Table 16. Symbol M95320-W M95320-R M95320-DF DC characteristics (M95320-W, device grade 6) Parameter Test conditions in addition to those defined in Max. Unit ILI Input leakage current VIN = VSS or VCC 2 A ILO Output leakage current S = VCC, VOUT = VSS or VCC 2 A ICC ICC0(2) ICC1 Supply current (Read) Supply current (Write) Supply current (Standby) VCC = 2.5 V, fC = 5 MHz, C = 0.1 VCC/0.9 VCC, Q = open 3 VCC = 2.5 V, fC = 10 MHz, C = 0.1 VCC/0.9 VCC, Q = open 2(1) VCC = 3.0 V, fC = 10 MHz C = 0.1 VCC/0.9 VCC, Q = open 4 VCC = 5.5 V, fC = 20 MHz, C = 0.1 VCC/0.9 VCC, Q = open 5(1) mA During tW, S = VCC, 2.5 V < VCC < 5.5 V 5 S = VCC, VCC = 5.5 V VIN = VSS or VCC 3(1) S = VCC, VCC = 5.0 V VIN = VSS or VCC 2 S = VCC, VCC = 2.5 V VIN = VSS or VCC 1(3) mA A VIL Input low voltage -0.45 0.3 VCC V VIH Input high voltage 0.7 VCC VCC+1 V VOL Output low voltage IOL = 1.5 mA, VCC = 2.5 V 0.4 V VOH Output high voltage VCC = 2.5 V and IOH = 0.4 mA or VCC = 5 V and IOH = 2 mA VRES(2) Internal reset threshold voltage 2. Characterized only, not tested in production. 3. 2 A with the device identified by process letter K. 4. 0.7 V with the device identified by process letter K. 5. 1.3 V with the device identified by process letter K. Doc ID 5711 Rev 15 V 0.8 VCC 1.0(4) 1. Only for the device identified by process letter K. 34/46 Min. 1.65(5) V M95320-W M95320-R M95320-DF Table 17. Symbol DC and AC parameters DC characteristics (M95320-R, device grade 6) Test conditions(1) Parameter Min. Max. Unit ILI Input leakage current VIN = VSS or VCC 2 A ILO Output leakage current S = VCC, voltage applied on Q = VSS or VCC 2 A ICC Supply current (Read) VCC = 1.8 V, max clock frequency (fC), C = 0.1VCC/0.9VCC, Q = open 2 mA VCC = 1.8 V, fC = 5 MHz, C = 0.1VCC/0.9VCC, Q = open 2(2) ICC0(3) Supply current (Write) VCC = 1.8 V, during tW, S = VCC 5 mA ICC1 Supply current (Standby) VCC = 1.8 V, S = VCC, VIN = VSS or VCC 1 A VIL Input low voltage 1.8 V VCC < 2.5 V -0.45 0.25 VCC V VIH Input high voltage 1.8 V VCC < 2.5 V 0.75 VCC VCC+1 V VOL Output low voltage IOL = 0.15 mA, VCC = 1.8 V 0.3 V VOH Output high voltage IOH = -0.1 mA, VCC = 1.8 V VRES(3) Internal reset threshold voltage 0.8 VCC 1.0(4) V 1.65(5) V 1. If the application uses the M95320-R device with 2.5 V < VCC < 5.5 V and -40 C < TA < +85 C, please refer to Table 16: DC characteristics (M95320-W, device grade 6), rather than to the above table. 2. For the device identified by process letter K. 3. Characterized only, not tested in production. 4. 0.7 V with the device identified by process letter K. 5. 1.3 V with the device identified by process letter K. Doc ID 5711 Rev 15 35/46 DC and AC parameters Table 18. Symbol M95320-W M95320-R M95320-DF DC characteristics (M95320-DF, device grade 6) Test conditions (1) Parameter Min. Max. Unit ILI Input leakage current VIN = VSS or VCC 2 A ILO Output leakage current S = VCC, voltage applied on Q = VSS or VCC 2 A ICC Supply current (Read) VCC = 1.7 V, max clock frequency (fC), C = 0.1 VCC/0.9 VCC, Q = open 2 VCC = 1.7 V, fC = 5 MHz, C = 0.1 VCC/0.9 VCC, Q = open 2 mA ICC0(2) Supply current (Write) VCC = 1.7 V, during tW, S = VCC 5 mA ICC1 Supply current (Standby) VCC = 1.7 V, S = VCC, VIN = VSS or VCC 1 A VIL Input low voltage 1.7 V VCC < 2.5 V -0.45 0.25 VCC V VIH Input high voltage 1.7 V VCC < 2.5 V 0.75 VCC VCC+1 V VOL Output low voltage IOL = 0.15 mA, VCC = 1.7 V 0.3 V VOH Output high voltage IOH = -0.1 mA, VCC = 1.7 V VRES(2) Internal reset threshold voltage 0.8 VCC 1.0 V 1.65 1. If the application uses the M95320-DF devices at 2.5 V VCC 5.5 V and -40 C TA +85 C, please refer to Table 16: DC characteristics (M95320-W, device grade 6), rather than to the above table. 2. Characterized only, not tested in production. 36/46 Doc ID 5711 Rev 15 V M95320-W M95320-R M95320-DF Table 19. DC and AC parameters AC characteristics (M95320-W, device grade 6) Test conditions specified in Table 10 and Table 12 VCC = 2.5 to 5.5 V Symbol Alt. Parameter New products VCC = 4.5 to 5.5 V Min. Max. Min. Max. D.C. 10 D.C. 20 Unit fC fSCK Clock frequency tSLCH tCSS1 S active setup time 30 15 ns tSHCH tCSS2 S not active setup time 30 15 ns tSHSL tCS S deselect time 40 20 ns tCHSH tCSH S active hold time 30 15 ns S not active hold time 30 15 ns tCHSL MHz tCH(1) tCLH Clock high time 42 20 ns tCL(1) tCLL Clock low time 40 20 ns tCLCH(2) tRC Clock rise time 2 2 s (2) tFC Clock fall time 2 2 s tCHCL tDVCH tDSU Data in setup time 10 5 ns tCHDX tDH Data in hold time 10 10 ns tHHCH Clock low hold time after HOLD not active 30 15 ns tHLCH Clock low hold time after HOLD active 30 15 ns tCLHL Clock low set-up time before HOLD active 0 0 ns tCLHH Clock low set-up time before HOLD not active 0 0 ns tSHQZ (2) tDIS Output disable time 40 20 ns Clock low to output valid 40 20 ns tCLQV(3) tV tCLQX tHO Output hold time tQLQH(2) tRO Output rise time 40 20 ns tQHQL(2) tFO Output fall time 40 20 ns tHHQV tLZ HOLD high to output valid 40 20 ns tHLQZ(2) tHZ HOLD low to output high-Z 40 20 ns tW tWC Write time 5 5 ms 0 0 ns 1. tCH + tCL must never be lower than the shortest possible clock period, 1/fC(max). 2. Characterized only, not tested in production. 3. tCLQV must be compatible with tCL (clock low time): if the SPI bus master offers a Read setup time tSU = 0 ns, tCL can be equal to (or greater than) tCLQV; in all other cases, tCL must be equal to (or greater than) tCLQV+tSU. Doc ID 5711 Rev 15 37/46 DC and AC parameters Table 20. M95320-W M95320-R M95320-DF AC characteristics (M95320-R, M95320-DF, device grade 6) Test conditions specified in Table 10 and Table 12(1) Symbol fC Alt. Parameter fSCK Clock frequency Min. Max. Unit D.C. 5 MHz tSLCH tCSS1 S active setup time 60 ns tSHCH tCSS2 S not active setup time 60 ns 90 ns 60 ns 60 ns tCLH Clock high time 90 ns tCLL Clock low time 90 ns tSHSL tCS tCHSH tCSH S active hold time S not active hold time tCHSL tCH(2) tCL (2) S deselect time tCLCH (3) tRC Clock rise time 2 s tCHCL (3) tFC Clock fall time 2 s tDVCH tDSU Data in setup time 20 ns tCHDX tDH Data in hold time 20 ns tHHCH Clock low hold time after HOLD not active 60 ns tHLCH Clock low hold time after HOLD active 60 ns tCLHL Clock low set-up time before HOLD active 0 ns tCLHH Clock low set-up time before HOLD not active 0 ns tSHQZ (3) tDIS Output disable time 80 ns Clock low to output valid 80 ns tCLQV tV tCLQX tHO Output hold time tQLQH(3) tRO Output rise time 80 ns tQHQL(3) tFO Output fall time 80 ns tHHQV tLZ HOLD high to output valid 80 ns tHLQZ(3) tHZ HOLD low to output high-Z 80 ns tW tWC Write time 5 ms 0 ns 1. If the application uses the M95320-R or M95320-DF at 2.5 V VCC 5.5 V and -40 C TA +85 C, please refer t to Table 19: AC characteristics (M95320-W, device grade 6) rather than to the above table. 2. tCH + tCL must never be lower than the shortest possible clock period, 1/fC(max). 3. Characterized only, not tested in production. 38/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF DC and AC parameters Figure 19. Serial input timing tSHSL S tCHSL tCH tSLCH tCHSH tSHCH C tDVCH tCHCL tCL tCLCH tCHDX D Q LSB IN MSB IN High impedance AI01447d Figure 20. Hold timing S tHLCH tCLHL tHHCH C tCLHH tHLQZ tHHQV Q HOLD AI01448c Doc ID 5711 Rev 15 39/46 DC and AC parameters M95320-W M95320-R M95320-DF Figure 21. Serial output timing S tCH tSHSL C tCLQV tCLCH tCHCL tCL tSHQZ tCLQX Q tQLQH tQHQL ADDR D LSB IN AI01449f 40/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 10 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 22. SO8N - 8-lead plastic small outline, 150 mils body width, package outline h x 45 A2 A c ccc b e 0.25 mm GAUGE PLANE D k 8 E1 E 1 A1 L L1 SO-A 1. Drawing is not to scale. Table 21. SO8N - 8-lead plastic small outline, 150 mils body width, mechanical data inches(1) millimeters Symbol Typ Min A Max Typ Min 1.750 Max 0.0689 A1 0.100 A2 1.250 b 0.280 0.480 0.0110 0.0189 c 0.170 0.230 0.0067 0.0091 ccc 0.250 0.0039 0.0098 0.0492 0.100 0.0039 D 4.900 4.800 5.000 0.1929 0.1890 0.1969 E 6.000 5.800 6.200 0.2362 0.2283 0.2441 E1 3.900 3.800 4.000 0.1535 0.1496 0.1575 e 1.270 - - 0.0500 - - h 0.250 0.500 0.0098 0.0197 k 0 8 0 8 L 0.400 1.270 0.0157 0.0500 L1 1.040 0.0409 1. Values in inches are converted from mm and rounded to four decimal digits. Doc ID 5711 Rev 15 41/46 Package mechanical data M95320-W M95320-R M95320-DF Figure 23. TSSOP8 - 8-lead thin shrink small outline, package outline D 8 5 c E1 1 E 4 A1 A L A2 L1 CP b e TSSOP8AM 1. Drawing is not to scale. Table 22. TSSOP8 - 8-lead thin shrink small outline, package mechanical data inches(1) millimeters Symbol Typ Min A Max 0.050 0.150 0.800 1.050 b 0.190 c 0.090 1.000 CP Max 0.0472 0.0020 0.0059 0.0315 0.0413 0.300 0.0075 0.0118 0.200 0.0035 0.0079 0.0394 0.100 0.0039 D 3.000 2.900 3.100 0.1181 0.1142 0.1220 e 0.650 - - 0.0256 - - E 6.400 6.200 6.600 0.2520 0.2441 0.2598 E1 4.400 4.300 4.500 0.1732 0.1693 0.1772 L 0.600 0.450 0.750 0.0236 0.0177 0.0295 L1 1.000 0 8 0.0394 0 N 8 8 1. Values in inches are converted from mm and rounded to four decimal digits. 42/46 Min 1.200 A1 A2 Typ Doc ID 5711 Rev 15 8 M95320-W M95320-R M95320-DF Package mechanical data Figure 24. UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat no lead, package outline E $ , , 0IN % B % + , ! $ EEE ! :7?-%E6 1. Drawing is not to scale. 2. The central pad (area E2 by D2 in the above illustration) is internally pulled to VSS. It must not be connected to any other voltage or signal line on the PCB, for example during the soldering process. Table 23. UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data inches(1) millimeters Symbol Typ Min Max Typ Min Max A 0.550 0.450 0.600 0.0217 0.0177 0.0236 A1 0.020 0.000 0.050 0.0008 0.0000 0.0020 b 0.250 0.200 0.300 0.0098 0.0079 0.0118 D 2.000 1.900 2.100 0.0787 0.0748 0.0827 1.200 1.600 0.0472 0.0630 2.900 3.100 0.1142 0.1220 1.200 1.600 0.0472 0.0630 D2 (rev MC) E 3.000 E2 (rev MC) e 0.500 0.1181 0.0197 K (rev MC) 0.300 L 0.300 L1 0.0118 0.500 0.0118 0.150 0.0197 0.0059 L3 0.300 0.0118 eee(2) 0.080 0.0031 1. Values in inches are converted from mm and rounded to four decimal digits. 2. Applied for exposed die paddle and terminals. Exclude embedding part of exposed die paddle from measuring. Doc ID 5711 Rev 15 43/46 Part numbering 11 M95320-W M95320-R M95320-DF Part numbering Table 24. Ordering information scheme Example: Device type M95 = SPI serial access EEPROM M95320 W MN 6 T P /P Device function 320 = 32 Kbit (4096 x 8) 320-D = 32 Kbit plus Identification page Operating voltage W = VCC = 2.5 to 5.5 V R = VCC = 1.8 to 5.5 V F = VCC = 1.7 to 5.5 V Package MN = SO8 (150 mil width) DW = TSSOP8 (169 mil width) MC = MLP8 (2 x 3 mm) Device grade 6 = Industrial temperature range, -40 to 85 C. Device tested with standard test flow Option blank = Standard packing T = Tape and reel packing Plating technology G or P = RoHS compliant and halogen-free (ECOPACK(R)) Process(1) /P or /K= Manufacturing technology code 1. The process letters appear on the device package (marking) and on the shipment box. Please contact your nearest ST Sales Office for further information. 44/46 Doc ID 5711 Rev 15 M95320-W M95320-R M95320-DF 12 Revision history Revision history Table 25. Date 13-May-2011 29-May-2012 12-Nov-2012 Document revision history Revision Changes 13 Added part number M95320-DR and related explanations: - Table 4: M95320-DR instruction set - Section 6.7: Read Identification Page - Section 6.9: Read Lock Status - Section 6.10: Lock ID - Figure 16: Read Lock Status sequence - Figure 17: Lock ID sequence Updated: - Features - Section 1: Description - Section 6.4: Write Status Register (WRSR) - Section 6.6: Write to Memory Array (WRITE) - Table 8: Absolute maximum ratings - Table 40: UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data - All tables in Section 9: DC and AC parameters - Section 11: Part numbering - Figure 27: UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat no lead, package outline. 14 Datasheet split into: - M95320-W, M95320-R, M95320-DR (this datasheet) for standard products (range 6), - M95320-125 datasheet for automotive products (range 3). 15 Removed: - M95320-DR product - MLP rev B package Added: - M95320-DF product Updated: - Section 7.2: Initial delivery state. Doc ID 5711 Rev 15 45/46 M95320-W M95320-R M95320-DF Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 46/46 Doc ID 5711 Rev 15