Data Sheet, V3.3, Feb. 2005
Microcontrollers
Never stop thinking.
C167CR
C167SR
16-Bit Single-Chip Microcontroller
Edition 2005-02
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
81669 München, Germany
© Infineon Technologies AG 2005.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Data Sheet, V3.3, Feb. 2005
Microcontrollers
Never stop thinking.
C167CR
C167SR
16-Bit Single-Chip Microcontroller
Template: mc_a5_ds_tmplt.fm / 4 / 2004-09-15
C167CR, C167SR
Revision History: 2005-02 V3.3
Previous Version: V3.2, 2001-07
V3.1, 2000-04
V3.0, 2000-02
1999-10 (Introduction of clock-related timing)
1999-06
1999-03 (Summarizes and replaces all older docs)
1998-03 (C167SR/CR, 25 MHz Addendum)
07.97 / 12.96 (C167CR-4RM)
12.96 (C167CR-16RM)
06.95 (C167CR, C167SR)
06.94 / 05.93 (C167)
Page Subjects (major changes since last revision)
all The layout of several graphics and text structures has been adapted to
company documentation rules, obvious typographical errors have been
corrected.
all The contents of this document have been re-arranged into numbered
sections and a table of contents has been added.
6BGA-type added to product list
8Pin designation corrected (pin 78)
9Input threshold control added to Port 6
17
25 Pin diagram and pin description for BGA package added
45 Port 6 added to input-threshold controlled ports
85 Mechanical package drawing corrected (P-MQFP-144-8)
86 Mechanical package drawing added (P-BGA-176-2)
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
mcdocu.comments@infineon.com
C167CR
C167SR
Table of Contents
Data Sheet 3 V3.3, 2005-02
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 General Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Pin Configuration and Definition for P-MQFP-144-8 . . . . . . . . . . . . . . . . . . 8
2.3 Pin Configuration and Definition for P-BGA-176-2 . . . . . . . . . . . . . . . . . . 17
3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1 Memory Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.2 External Bus Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3 Central Processing Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4 Interrupt System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.5 Capture/Compare (CAPCOM) Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.6 PWM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.7 General Purpose Timer (GPT) Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.8 A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.9 Serial Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.10 CAN-Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.11 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.12 Parallel Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.13 Oscillator Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.14 Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.15 Special Function Registers Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4 Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.1 General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.2 DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3 Analog/Digital Converter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.4 AC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.1 Definition of Internal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.2 External Clock Drive XTAL1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.4.3 Testing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.4.4 External Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
5 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table of Contents
C167CR/C167SR16-Bit Single-Chip Microcontroller
C166 Family
Data Sheet 4 V3.3, 2005-02
1 Summary of Features
High Performance 16-bit CPU with 4-Stage Pipeline
80/60 ns Instruction Cycle Time at 25/33 MHz CPU Clock
400/303 ns Multiplication (16 × 16 bits), 800/606 ns Division (32 / 16 bits)
Enhanced Boolean Bit Manipulation Facilities
Additional Instructions to Support HLL and Operating Systems
Register-Based Design with Multiple Variable Register Banks
Single-Cycle Context Switching Support
16 Mbytes Total Linear Address Space for Code and Data
1024 Bytes On-Chip Special Function Register Area
16-Priority-Level Interrupt System with 56 Sources, Sample-Rate down to 40/30 ns
8-Channel Interrupt-Driven Single-Cycle Data Transfer Facilities via
Peripheral Event Controller (PEC)
Clock Generation via on-chip PLL (factors 1:1.5/2/2.5/3/4/5),
via prescaler or via direct clock input
On-Chip Memory Modules
2 Kbytes On-Chip Internal RAM (IRAM)
2 Kbytes On-Chip Extension RAM (XRAM)
128/32 Kbytes On-Chip Mask ROM
On-Chip Peripheral Modules
16-Channel 10-bit A/D Converter with Programmable Conversion Time
down to 7.8 µs
Two 16-Channel Capture/Compare Units
4-Channel PWM Unit
Two Multi-Functional General Purpose Timer Units with 5 Timers
Two Serial Channels (Synchronous/Asynchronous and
High-Speed-Synchronous)
On-Chip CAN Interface (Rev. 2.0B active) with 15 Message Objects
(Full CAN / Basic CAN)
Up to 16 Mbytes External Address Space for Code and Data
Programmable External Bus Characteristics for Different Address Ranges
Multiplexed or Demultiplexed External Address/Data Buses with 8-Bit or 16-Bit
Data Bus Width
Five Programmable Chip-Select Signals
Hold- and Hold-Acknowledge Bus Arbitration Support
Idle and Power Down Modes
Programmable Watchdog Timer and Oscillator Watchdog
C167CR
C167SR
Summary of Features
Data Sheet 5 V3.3, 2005-02
Up to 111 General Purpose I/O Lines,
partly with Selectable Input Thresholds and Hysteresis
Supported by a Large Range of Development Tools like C-Compilers,
Macro-Assembler Packages, Emulators, Evaluation Boards, HLL-Debuggers,
Simulators, Logic Analyzer Disassemblers, Programming Boards
On-Chip Bootstrap Loader
144-Pin MQFP Package
176-Pin BGA Package1)
Ordering Information
The ordering code for Infineon microcontrollers provides an exact reference to the
required product. This ordering code identifies:
the derivative itself, i.e. its function set, the temperature range, and the supply voltage
the package and the type of delivery.
For the available ordering codes for the C167CR please refer to the “Product Catalog
Microcontrollers”, which summarizes all available microcontroller variants.
Note: The ordering codes for Mask-ROM versions are defined for each product after
verification of the respective ROM code.
This document describes several derivatives of the C167 group. Table 1 enumerates
these derivatives and summarizes the differences. As this document refers to all of these
derivatives, some descriptions may not apply to a specific product.
For simplicity all versions are referred to by the term C167CR throughout this document.
1) The external connections of the C167CR in P-BGA-176-2 are referred to as pins throughout this document,
although they are mechanically realized as solder balls.
C167CR
C167SR
Summary of Features
Data Sheet 6 V3.3, 2005-02
Table 1 C167CR Derivative Synopsis
Derivative1) Program
ROM Size
XRAM Size Operating
Frequency
Package
SAK-C167SR-LM
SAB-C167SR-LM
2 Kbytes 25 MHz P-MQFP-144-8
SAK-C167SR-L33M
SAB-C167SR-L33M
2 Kbytes 33 MHz P-MQFP-144-8
SAK-C167CR-LM
SAF-C167CR-LM
SAB-C167CR-LM
2 Kbytes 25 MHz P-MQFP-144-8
SAK-C167CR-L33M
SAB-C167CR-L33M
2 Kbytes 33 MHz P-MQFP-144-8
SAK-C167CR-4RM
SAB-C167CR-4RM
32 Kbytes 2 Kbytes 25 MHz P-MQFP-144-8
SAK-C167CR-4R33M
SAB-C167CR-4R33M
32 Kbytes 2 Kbytes 33 MHz P-MQFP-144-8
SAK-C167CR-16RM 128 Kbytes 2 Kbytes 25 MHz P-MQFP-144-8
SAK-C167CR-16R33M 128 Kbytes 2 Kbytes 33 MHz P-MQFP-144-8
SAK-C167CR-LE 2 Kbytes 25 MHz P-BGA-176-2
1) This Data Sheet is valid for devices manufactured in 0.5 µm technology, i.e. devices starting with and including
design step GA(-T)6.
C167CR
C167SR
General Device Information
Data Sheet 7 V3.3, 2005-02
2 General Device Information
2.1 Introduction
The C167CR derivatives are high performance derivatives of the Infineon C166 Family
of full featured single-chip CMOS microcontrollers. They combine high CPU
performance (up to 16.5 million instructions per second) with high peripheral functionality
and enhanced IO-capabilities. They also provide clock generation via PLL and various
on-chip memory modules such as program ROM, internal RAM, and extension RAM.
Figure 1 Logic Symbol
MCL04411
XTAL1
XTAL2
RSTOUT
ALE
NMI
RD
RSTIN
Port 0
16 Bit
16 Bit
Port 1
16 Bit
Port 2
15 Bit
Port 3
8 Bit
Port 4
VAREF AGND
V
WR/WRL
Port 5
16 Bit
Port 6
8 Bit
EA
READY
Port 7
8 Bit
8 Bit
Port 8
DD
VSS
V
C167CR
C167CR
C167SR
General Device Information
Data Sheet 8 V3.3, 2005-02
2.2 Pin Configuration and Definition for P-MQFP-144-8
The pins of the C167CR are described in detail in Table 2, including all their alternate
functions. Figure 2 summarizes all pins in a condensed way, showing their location on
the 4 sides of the package.
Note: The P-BGA-176-2 is described in Table 3 and Figure 3.
Figure 2 Pin Configuration P-MQFP-144-8 (top view)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
VAREF
VAGND
P5.10/AN10/T6EUD
P5.11/AN11/T5EUD
P5.12/AN12/T6IN
P5.13/AN13/T5IN
P5.14/AN14/T4EUD
P5.15/AN15/T2EUD
VSS
VDD
P2.0/CC0IO
P2.1/CC1IO
P2.2/CC2IO
P2.3/CC3IO
P2.4/CC4IO
P2.5/CC5IO
P2.6/CC6IO
P2.7/CC7IO
VSS
VDD
P2.8/CC8IO/EX0IN
P2.9/CC9IO/EX1IN
P2.10/CC10IO/EX2IN
P2.11/CC11IO/EX3IN
P2.12/CC12IO/EX4IN
P2.13/CC13IO/EX5IN
P2.14/CC14IO/EX6IN
P2.15/CC15IO/EX7IN/T7IN
P3.0/T0IN
P3.1/T6OUT
P3.2/CAPIN
P3.3/T3OUT
P3.4/T3EUD
P3.5/T4IN
VSS
VDD
VDD
VSS
NMI
RSTOUT
RSTIN
VSS
XTAL1
XTAL2
VDD
P1H.7/A15/CC27IO
P1H.6/A14/CC26IO
P1H.5/A13/CC25IO
P1H.4/A12/CC24IO
P1H.3/A11
P1H.2/A10
P1H.1/A9
P1H.0/A8
VSS
VDD
P1L.7/A7
P1L.6/A6
P1L.5/A5
P1L.4/A4
P1L.3/A3
P1L.2/A2
P1L.1/A1
P1L.0/A0
P0H.7/AD15
P0H.6/AD14
P0H.5/AD13
P0H.4/AD12
P0H.3/AD11
P0H.2/AD10
P0H.1/AD9
VSS
VDD
P0H.0/AD8
P0L.7/AD7
P0L.6/AD6
P0L.5/AD5
P0L.4/AD4
P0L.3/AD3
P0L.2/AD2
P0L.1/AD1
P0L.0/AD0
EA
ALE
READY
WR/WRL
RD
VSS
VDD
P4.7/A23
P4.6/A22/CAN1_TxD
P4.5/A21/CAN1_RxD
P4.4/A20
P4.3/A19
P4.2/A18
P4.1/A17
P4.0/A16
OWE
VSS
VDD
P3.15/CLKOUT
P3.13/SCLK
P3.12/BHE/WRH
P3.11/RxD0
P3.10/TxD0
P3.9/MTSR
P3.8/MRST
P3.7/T2IN
P3.6/T3IN
P6.0/CS0
P6.1/CS1
P6.2/CS2
P6.3/CS3
P6.4/CS4
P6.5/HOLD
P6.6/HLDA
P6.7/BREQ
P8.0/CC16IO
P8.1/CC17IO
P8.2/CC18IO
P8.3/CC19IO
P8.4/CC20IO
P8.5/CC21IO
P8.6/CC22IO
P8.7/CC23IO
VDD
VSS
P7.0/POUT0
P7.1/POUT1
P7.2/POUT2
P7.3/POUT3
P7.4/CC28IO
P7.5/CC29IO
P7.6/CC30IO
P7.7/CC31IO
P5.0/AN0
P5.1/AN1
P5.2/AN2
P5.3/AN3
P5.4/AN4
P5.5/AN5
P5.6/AN6
P5.7/AN7
P5.8/AN8
P5.9/AN9
C167CR
MCP04410
C167CR
C167SR
General Device Information
Data Sheet 9 V3.3, 2005-02
Table 2 Pin Definitions and Functions P-MQFP-144-8
Symbol Pin
No.
Input
Outp.
Function
P6
P6.0
P6.1
P6.2
P6.3
P6.4
P6.5
P6.6
P6.7
1
2
3
4
5
6
7
8
IO
O
O
O
O
O
I
I/O
O
Port 6 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 6 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 6
is selectable (TTL or special).
The Port 6 pins also serve for alternate functions:
CS0 Chip Select 0 Output
CS1 Chip Select 1 Output
CS2 Chip Select 2 Output
CS3 Chip Select 3 Output
CS4 Chip Select 4 Output
HOLD External Master Hold Request Input
HLDA Hold Acknowledge Output (master mode) or
Input (slave mode)
BREQ Bus Request Output
P8
P8.0
P8.1
P8.2
P8.3
P8.4
P8.5
P8.6
P8.7
9
10
11
12
13
14
15
16
IO
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Port 8 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 8 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 8
is selectable (TTL or special).
The following Port 8 pins also serve for alternate functions:
CC16IO CAPCOM2: CC16 Capture Inp./Compare Outp.
CC17IO CAPCOM2: CC17 Capture Inp./Compare Outp.
CC18IO CAPCOM2: CC18 Capture Inp./Compare Outp.
CC19IO CAPCOM2: CC19 Capture Inp./Compare Outp.
CC20IO CAPCOM2: CC20 Capture Inp./Compare Outp.
CC21IO CAPCOM2: CC21 Capture Inp./Compare Outp.
CC22IO CAPCOM2: CC22 Capture Inp./Compare Outp.
CC23IO CAPCOM2: CC23 Capture Inp./Compare Outp.
C167CR
C167SR
General Device Information
Data Sheet 10 V3.3, 2005-02
P7
P7.0
P7.1
P7.2
P7.3
P7.4
P7.5
P7.6
P7.7
19
20
21
22
23
24
25
26
IO
O
O
O
O
I/O
I/O
I/O
I/O
Port 7 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 7 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 7
is selectable (TTL or special).
The following Port 7 pins also serve for alternate functions:
POUT0 PWM Channel 0 Output
POUT1 PWM Channel 1 Output
POUT2 PWM Channel 2 Output
POUT3 PWM Channel 3 Output
CC28IO CAPCOM2: CC28 Capture Inp./Compare Outp.
CC29IO CAPCOM2: CC29 Capture Inp./Compare Outp.
CC30IO CAPCOM2: CC30 Capture Inp./Compare Outp.
CC31IO CAPCOM2: CC31 Capture Inp./Compare Outp.
P5
P5.0
P5.1
P5.2
P5.3
P5.4
P5.5
P5.6
P5.7
P5.8
P5.9
P5.10
P5.11
P5.12
P5.13
P5.14
P5.15
27
28
29
30
31
32
33
34
35
36
39
40
41
42
43
44
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Port 5 is a 16-bit input-only port with Schmitt-Trigger
characteristic.
The pins of Port 5 also serve as analog input channels for the
A/D converter, or they serve as timer inputs:
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10, T6EUD GPT2 Timer T6 Ext. Up/Down Ctrl. Inp.
AN11, T5EUD GPT2 Timer T5 Ext. Up/Down Ctrl. Inp.
AN12, T6IN GPT2 Timer T6 Count Inp.
AN13, T5IN GPT2 Timer T5 Count Inp.
AN14, T4EUD GPT1 Timer T4 Ext. Up/Down Ctrl. Inp.
AN15, T2EUD GPT1 Timer T5 Ext. Up/Down Ctrl. Inp.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 11 V3.3, 2005-02
P2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
P2.8
P2.9
P2.10
P2.11
P2.12
P2.13
P2.14
P2.15
47
48
49
50
51
52
53
54
57
58
59
60
61
62
63
64
IO
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I
Port 2 is a 16-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 2 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 2
is selectable (TTL or special).
The following Port 2 pins also serve for alternate functions:
CC0IO CAPCOM1: CC0 Capture Inp./Compare Output
CC1IO CAPCOM1: CC1 Capture Inp./Compare Output
CC2IO CAPCOM1: CC2 Capture Inp./Compare Output
CC3IO CAPCOM1: CC3 Capture Inp./Compare Output
CC4IO CAPCOM1: CC4 Capture Inp./Compare Output
CC5IO CAPCOM1: CC5 Capture Inp./Compare Output
CC6IO CAPCOM1: CC6 Capture Inp./Compare Output
CC7IO CAPCOM1: CC7 Capture Inp./Compare Output
CC8IO CAPCOM1: CC8 Capture Inp./Compare Output,
EX0IN Fast External Interrupt 0 Input
CC9IO CAPCOM1: CC9 Capture Inp./Compare Output,
EX1IN Fast External Interrupt 1 Input
CC10IO CAPCOM1: CC10 Capture Inp./Compare Outp.,
EX2IN Fast External Interrupt 2 Input
CC11IO CAPCOM1: CC11 Capture Inp./Compare Outp.,
EX3IN Fast External Interrupt 3 Input
CC12IO CAPCOM1: CC12 Capture Inp./Compare Outp.,
EX4IN Fast External Interrupt 4 Input
CC13IO CAPCOM1: CC13 Capture Inp./Compare Outp.,
EX5IN Fast External Interrupt 5 Input
CC14IO CAPCOM1: CC14 Capture Inp./Compare Outp.,
EX6IN Fast External Interrupt 6 Input
CC15IO CAPCOM1: CC15 Capture Inp./Compare Outp.,
EX7IN Fast External Interrupt 7 Input,
T7IN CAPCOM2: Timer T7 Count Input
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 12 V3.3, 2005-02
P3
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
P3.8
P3.9
P3.10
P3.11
P3.12
P3.13
P3.15
65
66
67
68
69
70
73
74
75
76
77
78
79
80
81
IO
I
O
I
O
I
I
I
I
I/O
I/O
O
I/O
O
O
I/O
O
Port 3 is a 15-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 3 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 3
is selectable (TTL or special).
The following Port 3 pins also serve for alternate functions:
T0IN CAPCOM1 Timer T0 Count Input
T6OUT GPT2 Timer T6 Toggle Latch Output
CAPIN GPT2 Register CAPREL Capture Input
T3OUT GPT1 Timer T3 Toggle Latch Output
T3EUD GPT1 Timer T3 External Up/Down Control Input
T4IN GPT1 Timer T4 Count/Gate/Reload/Capture Inp.
T3IN GPT1 Timer T3 Count/Gate Input
T2IN GPT1 Timer T2 Count/Gate/Reload/Capture Inp.
MRST SSC Master-Receive/Slave-Transmit Inp./Outp.
MTSR SSC Master-Transmit/Slave-Receive Outp./Inp.
TxD0 ASC0 Clock/Data Output (Async./Sync.)
RxD0 ASC0 Data Input (Async.) or Inp./Outp. (Sync.)
BHE External Memory High Byte Enable Signal,
WRH External Memory High Byte Write Strobe
SCLK SSC Master Clock Output / Slave Clock Input.
CLKOUT System Clock Output (= CPU Clock)
OWE
(VPP)
84 I Oscillator Watchdog Enable. This input enables the oscillator
watchdog when high or disables it when low e.g. for testing
purposes. An internal pull-up device holds this input high if
nothing is driving it.
For normal operation pin OWE should be high or not
connected.
In order to drive pin OWE low draw a current of at least
200 µA.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 13 V3.3, 2005-02
P4
P4.0
P4.1
P4.2
P4.3
P4.4
P4.5
P4.6
P4.7
85
86
87
88
89
90
91
92
IO
O
O
O
O
O
O
I
O
O
O
Port 4 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state.
Port 4 can be used to output the segment address lines and
for serial bus interfaces:
A16 Least Significant Segment Address Line
A17 Segment Address Line
A18 Segment Address Line
A19 Segment Address Line
A20 Segment Address Line
A21 Segment Address Line,
CAN1_RxD CAN 1 Receive Data Input
A22 Segment Address Line,
CAN1_TxD CAN 1 Transmit Data Output
A23 Most Significant Segment Address Line
RD 95 O External Memory Read Strobe. RD is activated for every
external instruction or data read access.
WR/
WRL
96 O External Memory Write Strobe. In WR-mode this pin is
activated for every external data write access. In WRL-mode
this pin is activated for low byte data write accesses on a
16-bit bus, and for every data write access on an 8-bit bus.
See WRCFG in register SYSCON for mode selection.
READY 97 I Ready Input. When the Ready function is enabled, a high
level at this pin during an external memory access will force
the insertion of memory cycle time waitstates until the pin
returns to a low level.
An internal pull-up device will hold this pin high when nothing
is driving it.
ALE 98 O Address Latch Enable Output. Can be used for latching the
address into external memory or an address latch in the
multiplexed bus modes.
EA 99 I External Access Enable pin. A low level at this pin during and
after Reset forces the C167CR to begin instruction execution
out of external memory. A high level forces execution out of
the internal program memory.
“ROMless” versions must have this pin tied to ‘0’.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 14 V3.3, 2005-02
PORT0
P0L.0-7
P0H.0-7
100-
107
108,
111-
117
IO PORT0 consists of the two 8-bit bidirectional I/O ports P0L
and P0H. It is bit-wise programmable for input or output via
direction bits. For a pin configured as input, the output driver
is put into high-impedance state.
In case of an external bus configuration, PORT0 serves as
the address (A) and address/data (AD) bus in multiplexed
bus modes and as the data (D) bus in demultiplexed bus
modes.
Demultiplexed bus modes:
8-bit data bus: P0H = I/O, P0L = D7 - D0
16-bit data bus: P0H = D15 - D8, P0L = D7 - D0
Multiplexed bus modes:
8-bit data bus: P0H = A15 - A8, P0L = AD7 - AD0
16-bit data bus: P0H = AD15 - AD8, P0L = AD7 - AD0
PORT1
P1L.0-7
P1H.0-7
P1H.4
P1H.5
P1H.6
P1H.7
118-
125
128-
135
132
133
134
135
IO
I
I
I
I
PORT1 consists of the two 8-bit bidirectional I/O ports P1L
and P1H. It is bit-wise programmable for input or output via
direction bits. For a pin configured as input, the output driver
is put into high-impedance state. PORT1 is used as the 16-bit
address bus (A) in demultiplexed bus modes and also after
switching from a demultiplexed bus mode to a multiplexed
bus mode.
The following PORT1 pins also serve for alternate functions:
CC24IO CAPCOM2: CC24 Capture Input
CC25IO CAPCOM2: CC25 Capture Input
CC26IO CAPCOM2: CC26 Capture Input
CC27IO CAPCOM2: CC27 Capture Input
XTAL2
XTAL1
137
138
O
I
XTAL2: Output of the oscillator amplifier circuit.
XTAL1: Input to the oscillator amplifier and input to the
internal clock generator
To clock the device from an external source, drive XTAL1,
while leaving XTAL2 unconnected. Minimum and maximum
high/low and rise/fall times specified in the AC
Characteristics must be observed.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 15 V3.3, 2005-02
RSTIN 140 I/O Reset Input with Schmitt-Trigger characteristics. A low level
at this pin while the oscillator is running resets the C167CR.
An internal pull-up resistor permits power-on reset using only
a capacitor connected to VSS.
A spike filter suppresses input pulses < 10 ns. Input pulses
> 100 ns safely pass the filter. The minimum duration for a
safe recognition should be 100 ns + 2 CPU clock cycles.
In bidirectional reset mode (enabled by setting bit BDRSTEN
in register SYSCON) the RSTIN line is internally pulled low
for the duration of the internal reset sequence upon any reset
(HW, SW, WDT). See note below this table.
Note: To let the reset configuration of PORT0 settle and to let
the PLL lock a reset duration of ca. 1 ms is
recommended.
RST
OUT
141 O Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or
a watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
NMI 142 I Non-Maskable Interrupt Input. A high to low transition at this
pin causes the CPU to vector to the NMI trap routine. When
the PWRDN (power down) instruction is executed, the NMI
pin must be low in order to force the C167CR to go into power
down mode. If NMI is high, when PWRDN is executed, the
part will continue to run in normal mode.
If not used, pin NMI should be pulled high externally.
VAREF 37 Reference voltage for the A/D converter.
VAGND 38 Reference ground for the A/D converter.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 16 V3.3, 2005-02
Note: The following behavioural differences must be observed when the bidirectional
reset is active:
Bit BDRSTEN in register SYSCON cannot be changed after EINIT and is cleared
automatically after a reset.
The reset indication flags always indicate a long hardware reset.
The PORT0 configuration is treated as if it were a hardware reset. In particular, the
bootstrap loader may be activated when P0L.4 is low.
•Pin RSTIN
may only be connected to external reset devices with an open drain output
driver.
A short hardware reset is extended to the duration of the internal reset sequence.
VDD 17, 46,
56, 72,
82, 93,
109,
126,
136,
144
Digital Supply Voltage:
+ 5 V during normal operation and idle mode.
2.5 V during power down mode.
VSS 18, 45,
55, 71,
83, 94,
110,
127,
139,
143
Digital Ground.
Table 2 Pin Definitions and Functions P-MQFP-144-8 (cont’d)
Symbol Pin
No.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 17 V3.3, 2005-02
2.3 Pin Configuration and Definition for P-BGA-176-2
The pins1) of the C167CR are described in detail in Table 3, including all their alternate
functions. Figure 3 summarizes all pins in a condensed way, showing their location on
the bottom of the package.
Note: The P-MQFP-144-8 is described in Table 2 and Figure 2.
Figure 3 Pin Configuration P-BGA-176-2 (top view)
1) The external connections of the C167CR in P-BGA-176-2 are referred to as pins throughout this document,
although they are mechanically realized as solder balls.
mc_c167crle_pindiagram.vsd
A
B
C
D
E
F
G
H
J
K
L
M
N
P
1 2 3 4 5 6 7 8 9 1011121314
P5.0 P7.7
P5.4
P5.1
P5.14P5.15
P5.6P5.9
P5.7P5.10
P5.13
P5.11
V
SS
V
DD
P2.3
P2.1
P2.4P2.6 P2.5
P2.7
V
SS
P2.9 P2.10 P2.12
P2.13
V
DD
P2.8
P2.11
P2.15
P3.1
V
DD
P3.2 P3.12
P3.6
P3.13
P4.2
P3.15
P4.6
P4.1
P4.4
P4.3
P4.5
ALE
P0.1
P0.3
P0.8
P0.2
P0.13
P0.7
P1.3
P0.9
P1.2
P0.10
P1.4 P1.5
P0.15
P0.5
P1.11
P1.13
P0.14
P1.7
P1.9 P1.12P1.10
P1.14
RST
IN P1.15
XTAL2
NMIXTAL1
P6.1
P6.6
P6.0
P6.5
P6.2
P6.3P8.3
P8.2
P8.0
P8.7
P6.4P6.7P8.1
P7.0
P7.6
P8.5
P7.2
P7.5
P7.4
V
SS
V
AREF
V
SS
V
DD
V
SS
V
DD
Not connected or thermal ground
1 2 3 4 5 6 7 8 9 1011121314
A
B
C
D
E
F
G
H
J
K
L
M
N
P
P8.4P5.8
P5.2P5.5 P7.3
V
AGND
P5.3 P7.1
V
DD
RST
OUT
V
SS
P8.6
P5.12
V
SS
P2.0 P2.2
P1.8
P1.6
V
DD
P1.1P1.0
P2.14
V
SS
V
SS
RD P0.12 P0.11
V
DD
EA
V
SS
V
DD
P3.11P3.3P3.0
P3.4 P3.7 P3.8 P3.10 P4.7 WR P0.0 P0.4
P0.6
REA
DY
V
DD
P4.0P3.9P3.5
OWE
C167CR
C167SR
General Device Information
Data Sheet 18 V3.3, 2005-02
Table 3 Pin Definitions and Functions P-BGA-176-2
Symbol Pin
Num.
Input
Outp.
Function
P5
P5.0
P5.1
P5.2
P5.3
P5.4
P5.5
P5.6
P5.7
P5.8
P5.9
P5.10
P5.11
P5.12
P5.13
P5.14
P5.15
A5
D5
A4
C5
B4
A3
C4
D4
B3
C3
D3
C1
D1
D2
E3
E2
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Port 5 is a 16-bit input-only port with Schmitt-Trigger
characteristic.
The pins of Port 5 also serve as analog input channels for the
A/D converter, or they serve as timer inputs:
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10, T6EUD GPT2 Timer T6 Ext. Up/Down Ctrl. Inp.
AN11, T5EUD GPT2 Timer T5 Ext. Up/Down Ctrl. Inp.
AN12, T6IN GPT2 Timer T6 Count Inp.
AN13, T5IN GPT2 Timer T5 Count Inp.
AN14, T4EUD GPT1 Timer T4 Ext. Up/Down Ctrl. Inp.
AN15, T2EUD GPT1 Timer T5 Ext. Up/Down Ctrl. Inp.
P7
P7.0
P7.1
P7.2
P7.3
P7.4
P7.5
P7.6
P7.7
D7
C7
B7
A7
D6
C6
B6
A6
IO
O
O
O
O
I/O
I/O
I/O
I/O
Port 7 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 7 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 7
is selectable (TTL or special).
The following Port 7 pins also serve for alternate functions:
POUT0 PWM Channel 0 Output
POUT1 PWM Channel 1 Output
POUT2 PWM Channel 2 Output
POUT3 PWM Channel 3 Output
CC28IO CAPCOM2: CC28 Capture Inp./Compare Outp.
CC29IO CAPCOM2: CC29 Capture Inp./Compare Outp.
CC30IO CAPCOM2: CC30 Capture Inp./Compare Outp.
CC31IO CAPCOM2: CC31 Capture Inp./Compare Outp.
C167CR
C167SR
General Device Information
Data Sheet 19 V3.3, 2005-02
P8
P8.0
P8.1
P8.2
P8.3
P8.4
P8.5
P8.6
P8.7
B10
A10
D9
C9
B9
A9
D8
C8
IO
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Port 8 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 8 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 8
is selectable (TTL or special).
The following Port 8 pins also serve for alternate functions:
CC16IO CAPCOM2: CC16 Capture Inp./Compare Outp.
CC17IO CAPCOM2: CC17 Capture Inp./Compare Outp.
CC18IO CAPCOM2: CC18 Capture Inp./Compare Outp.
CC19IO CAPCOM2: CC19 Capture Inp./Compare Outp.
CC20IO CAPCOM2: CC20 Capture Inp./Compare Outp.
CC21IO CAPCOM2: CC21 Capture Inp./Compare Outp.
CC22IO CAPCOM2: CC22 Capture Inp./Compare Outp.
CC23IO CAPCOM2: CC23 Capture Inp./Compare Outp.
P6
P6.0
P6.1
P6.2
P6.3
P6.4
P6.5
P6.6
P6.7
A13
B12
D10
C11
A12
B11
C10
A11
IO
O
O
O
O
O
I
I/O
O
Port 6 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 6 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 6
is selectable (TTL or special).
The Port 6 pins also serve for alternate functions:
CS0 Chip Select 0 Output
CS1 Chip Select 1 Output
CS2 Chip Select 2 Output
CS3 Chip Select 3 Output
CS4 Chip Select 4 Output
HOLD External Master Hold Request Input
HLDA Hold Acknowledge Output (master mode) or
Input (slave mode)
BREQ Bus Request Output
NMI C14 I Non-Maskable Interrupt Input. A high to low transition at this
pin causes the CPU to vector to the NMI trap routine. When
the PWRDN (power down) instruction is executed, the NMI
pin must be low in order to force the C167CR to go into power
down mode. If NMI is high, when PWRDN is executed, the
part will continue to run in normal mode.
If not used, pin NMI should be pulled high externally.
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 20 V3.3, 2005-02
XTAL2
XTAL1
D13
C13
O
I
XTAL2: Output of the oscillator amplifier circuit.
XTAL1: Input to the oscillator amplifier and input to the
internal clock generator.
To clock the device from an external source, drive XTAL1,
while leaving XTAL2 unconnected. Minimum and maximum
high/low and rise/fall times specified in the AC
Characteristics must be observed.
RST
OUT
D12 O Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or
a watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
RSTIN E11 I/O Reset Input with Schmitt-Trigger characteristics. A low level
at this pin while the oscillator is running resets the C167CR.
An internal pull-up resistor permits power-on reset using only
a capacitor connected to VSS.
A spike filter suppresses input pulses < 10 ns. Input pulses
> 100 ns safely pass the filter. The minimum duration for a
safe recognition should be 100 ns + 2 CPU clock cycles.
In bidirectional reset mode (enabled by setting bit BDRSTEN
in register SYSCON) the RSTIN line is internally pulled low
for the duration of the internal reset sequence upon any reset
(HW, SW, WDT). See note below this table.
Note: To let the reset configuration of PORT0 settle and to let
the PLL lock a reset duration of ca. 1 ms is
recommended.
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 21 V3.3, 2005-02
PORT1
P1L.0-7
P1H.0-3
P1H.4
P1H.5
P1H.6
P1H.7
K13,
K14,
J13,
J14,
H11,
H12,
H13,
G11
G13,
F11,
F12,
G14
F13
F14
E14
E13
IO
I
I
I
I
PORT1 consists of the two 8-bit bidirectional I/O ports P1L
and P1H. It is bit-wise programmable for input or output via
direction bits. For a pin configured as input, the output driver
is put into high-impedance state. PORT1 is used as the 16-bit
address bus (A) in demultiplexed bus modes and also after
switching from a demultiplexed bus mode to a multiplexed
bus mode.
The following PORT1 pins also serve for alternate functions:
CC24IO CAPCOM2: CC24 Capture Input
CC25IO CAPCOM2: CC25 Capture Input
CC26IO CAPCOM2: CC26 Capture Input
CC27IO CAPCOM2: CC27 Capture Input
PORT0
P0L.0-7
P0H.0-7
N10,
L9,
P11,
M10,
N11,
M11,
P12,
N12
L10,
K11,
L12,
L14,
L13,
K12,
J11,
J12
IO PORT0 consists of the two 8-bit bidirectional I/O ports P0L
and P0H. It is bit-wise programmable for input or output via
direction bits. For a pin configured as input, the output driver
is put into high-impedance state.
In case of an external bus configuration, PORT0 serves as
the address (A) and address/data (AD) bus in multiplexed
bus modes and as the data (D) bus in demultiplexed bus
modes.
Demultiplexed bus modes:
8-bit data bus: P0H = I/O, P0L = D7 - D0
16-bit data bus: P0H = D15 - D8, P0L = D7 - D0
Multiplexed bus modes:
8-bit data bus: P0H = A15 - A8, P0L = AD7 - AD0
16-bit data bus: P0H = AD15 - AD8, P0L = AD7 - AD0
RD L8 O External Memory Read Strobe. RD is activated for every
external instruction or data read access.
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 22 V3.3, 2005-02
EA M9 I External Access Enable pin. A low level at this pin during and
after Reset forces the C167CR to begin instruction execution
out of external memory. A high level forces execution out of
the internal program memory.
“ROMless” versions must have this pin tied to ‘0’.
WR/
WRL
N9 O External Memory Write Strobe. In WR-mode this pin is
activated for every external data write access. In WRL-mode
this pin is activated for low byte data write accesses on a
16-bit bus, and for every data write access on an 8-bit bus.
See WRCFG in register SYSCON for mode selection.
READY P9 I Ready Input. When the Ready function is enabled, a high
level at this pin during an external memory access will force
the insertion of memory cycle time waitstates until the pin
returns to a low level.
An internal pull-up device will hold this pin high when nothing
is driving it.
ALE P10 O Address Latch Enable Output. Can be used for latching the
address into external memory or an address latch in the
multiplexed bus modes.
P4
P4.0
P4.1
P4.2
P4.3
P4.4
P4.5
P4.6
P4.7
P6
M6
L6
N7
P7
M7
L7
N8
IO
O
O
O
O
O
O
I
O
O
O
Port 4 is an 8-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state.
Port 4 can be used to output the segment address lines and
for serial bus interfaces:
A16 Least Significant Segment Address Line
A17 Segment Address Line
A18 Segment Address Line
A19 Segment Address Line
A20 Segment Address Line
A21 Segment Address Line,
CAN1_RxD CAN 1 Receive Data Input
A22 Segment Address Line,
CAN1_TxD CAN 1 Transmit Data Output
A23 Most Significant Segment Address Line
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 23 V3.3, 2005-02
OWE
(VPP)
N6 I Oscillator Watchdog Enable. This input enables the oscillator
watchdog when high or disables it when low e.g. for testing
purposes. An internal pull-up device holds this input high if
nothing is driving it.
For normal operation pin OWE should be high or not
connected.
In order to drive pin OWE low draw a current of at least
200 µA.
P3
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
P3.8
P3.9
P3.10
P3.11
P3.12
P3.13
P3.15
M1
K3
L2
M2
N1
P2
M3
N2
N3
P3
N4
M4
L4
P4
N5
IO
I
O
I
O
I
I
I
I
I/O
I/O
O
I/O
O
O
I/O
O
Port 3 is a 15-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 3 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 3
is selectable (TTL or special).
The following Port 3 pins also serve for alternate functions:
T0IN CAPCOM1 Timer T0 Count Input
T6OUT GPT2 Timer T6 Toggle Latch Output
CAPIN GPT2 Register CAPREL Capture Input
T3OUT GPT1 Timer T3 Toggle Latch Output
T3EUD GPT1 Timer T3 External Up/Down Control Input
T4IN GPT1 Timer T4 Count/Gate/Reload/Capture Inp.
T3IN GPT1 Timer T3 Count/Gate Input
T2IN GPT1 Timer T2 Count/Gate/Reload/Capture Inp.
MRST SSC Master-Receive/Slave-Transmit Inp./Outp.
MTSR SSC Master-Transmit/Slave-Receive Outp./Inp.
TxD0 ASC0 Clock/Data Output (Async./Sync.)
RxD0 ASC0 Data Input (Async.) or Inp./Outp. (Sync.)
BHE External Memory High Byte Enable Signal,
WRH External Memory High Byte Write Strobe
SCLK SSC Master Clock Output / Slave Clock Input.
CLKOUT System Clock Output (= CPU Clock)
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 24 V3.3, 2005-02
P2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
P2.8
P2.9
P2.10
P2.11
P2.12
P2.13
P2.14
P2.15
F3
F2
F4
G4
G3
G2
G1
H1
H4
J1
J2
J4
J3
K1
K2
L1
IO
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I
Port 2 is a 16-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 2 outputs can be configured as
push/pull or open drain drivers. The input threshold of Port 2
is selectable (TTL or special).
The following Port 2 pins also serve for alternate functions:
CC0IO CAPCOM1: CC0 Capture Inp./Compare Output
CC1IO CAPCOM1: CC1 Capture Inp./Compare Output
CC2IO CAPCOM1: CC2 Capture Inp./Compare Output
CC3IO CAPCOM1: CC3 Capture Inp./Compare Output
CC4IO CAPCOM1: CC4 Capture Inp./Compare Output
CC5IO CAPCOM1: CC5 Capture Inp./Compare Output
CC6IO CAPCOM1: CC6 Capture Inp./Compare Output
CC7IO CAPCOM1: CC7 Capture Inp./Compare Output
CC8IO CAPCOM1: CC8 Capture Inp./Compare Output,
EX0IN Fast External Interrupt 0 Input
CC9IO CAPCOM1: CC9 Capture Inp./Compare Output,
EX1IN Fast External Interrupt 1 Input
CC10IO CAPCOM1: CC10 Capture Inp./Compare Outp.,
EX2IN Fast External Interrupt 2 Input
CC11IO CAPCOM1: CC11 Capture Inp./Compare Outp.,
EX3IN Fast External Interrupt 3 Input
CC12IO CAPCOM1: CC12 Capture Inp./Compare Outp.,
EX4IN Fast External Interrupt 4 Input
CC13IO CAPCOM1: CC13 Capture Inp./Compare Outp.,
EX5IN Fast External Interrupt 5 Input
CC14IO CAPCOM1: CC14 Capture Inp./Compare Outp.,
EX6IN Fast External Interrupt 6 Input
CC15IO CAPCOM1: CC15 Capture Inp./Compare Outp.,
EX7IN Fast External Interrupt 7 Input,
T7IN CAPCOM2: Timer T7 Count Input
VAREF B2 Reference voltage for the A/D converter.
VAGND C2 Reference ground for the A/D converter.
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
General Device Information
Data Sheet 25 V3.3, 2005-02
Note: The following behavioural differences must be observed when the bidirectional
reset is active:
Bit BDRSTEN in register SYSCON cannot be changed after EINIT and is cleared
automatically after a reset.
The reset indication flags always indicate a long hardware reset.
The PORT0 configuration is treated as if it were a hardware reset. In particular, the
bootstrap loader may be activated when P0L.4 is low.
•Pin RSTIN
may only be connected to external reset devices with an open drain output
driver.
A short hardware reset is extended to the duration of the internal reset sequence.
VDD B8,
C12,
D14,
F1,
H3,
H14,
K4,
M5,
M12,
P8
Digital Supply Voltage:
+ 5 V during normal operation and idle mode.
2.5 V during power down mode.
VSS A8,
D11,
E1,
E12,
G12,
H2,
L3,
L5,
L11,
M8
Digital Ground.
Table 3 Pin Definitions and Functions P-BGA-176-2 (cont’d)
Symbol Pin
Num.
Input
Outp.
Function
C167CR
C167SR
Functional Description
Data Sheet 26 V3.3, 2005-02
3 Functional Description
The architecture of the C167CR combines advantages of both RISC and CISC
processors and of advanced peripheral subsystems in a very well-balanced way. In
addition the on-chip memory blocks allow the design of compact systems with maximum
performance.
The following block diagram gives an overview of the different on-chip components and
of the advanced, high bandwidth internal bus structure of the C167CR.
Note: All time specifications refer to a CPU clock of 33 MHz
(see definition in the AC Characteristics section).
Figure 4 Block Diagram
The program memory, the internal RAM (IRAM) and the set of generic peripherals are
connected to the CPU via separate buses. A fourth bus, the XBUS, connects external
resources as well as additional on-chip resources, the X-Peripherals (see Figure 4).
C166-Core
CPU
Port 2
Interrupt Bus
XTAL
Osc / PLL
WDT
32
16
Interrupt Controller 16-Level
Priority
PEC
External Instr. / Data
GPT
T2
T3
T4
T5
T6
SSC
BRGen
(SPI)
ASC0
BRGen
(USART)
ADC
10-Bit
16
Channels
PWM CCOM1
T0
T1
CCOM2
T7
T8
EBC
XBUS Control
External Bus
Control
Dual Port
IRAM
Internal
RAM
2 KByte
ProgMem
ROM
128/32
KByte
Data
Data
16
16
16
CAN
Rev 2.0B active
Instr. / Data
Port 0
XRAM
2 KByte
Port 6
8
8
Port 1
16 16
16
Port 5 Port 3
15
Port 7
8
Port 8
8
Port 4
16
On-Chip XBUS (16-Bit Demux)
Peripheral Data Bus
16
C167CR
C167SR
Functional Description
Data Sheet 27 V3.3, 2005-02
3.1 Memory Organization
The memory space of the C167CR is configured in a Von Neumann architecture which
means that code memory, data memory, registers and I/O ports are organized within the
same linear address space which includes 16 Mbytes. The entire memory space can be
accessed bytewise or wordwise. Particular portions of the on-chip memory have
additionally been made directly bitaddressable.
The C167CR incorporates 128/32 Kbytes (depending on the derivative) of on-chip mask-
programmable ROM for code or constant data. The lower 32 Kbytes of the on-chip ROM
can be mapped either to segment 0 or segment 1.
2 Kbytes of on-chip Internal RAM (IRAM) are provided as a storage for user defined
variables, for the system stack, general purpose register banks and even for code. A
register bank can consist of up to 16 wordwide (R0 to R15) and/or bytewide (RL0, RH0,
…, RL7, RH7) so-called General Purpose Registers (GPRs).
1024 bytes (2 × 512 bytes) of the address space are reserved for the Special Function
Register areas (SFR space and ESFR space). SFRs are wordwide registers which are
used for controlling and monitoring functions of the different on-chip units. Unused SFR
addresses are reserved for future members of the C166 Family.
2 Kbytes of on-chip Extension RAM (XRAM) are provided to store user data, user stacks,
or code. The XRAM is accessed like external memory and therefore cannot be used for
the system stack or for register banks and is not bitaddressable. The XRAM permits
16-bit accesses with maximum speed.
In order to meet the needs of designs where more memory is required than is provided
on chip, up to 16 Mbytes of external RAM and/or ROM can be connected to the
microcontroller.
C167CR
C167SR
Functional Description
Data Sheet 28 V3.3, 2005-02
3.2 External Bus Controller
All of the external memory accesses are performed by a particular on-chip External Bus
Controller (EBC). It can be programmed either to Single Chip Mode when no external
memory is required, or to one of four different external memory access modes, which are
as follows:
16-/18-/20-/24-bit Addresses, 16-bit Data, Demultiplexed
16-/18-/20-/24-bit Addresses, 16-bit Data, Multiplexed
16-/18-/20-/24-bit Addresses, 8-bit Data, Multiplexed
16-/18-/20-/24-bit Addresses, 8-bit Data, Demultiplexed
In the demultiplexed bus modes, addresses are output on PORT1 and data is
input/output on PORT0 or P0L, respectively. In the multiplexed bus modes both
addresses and data use PORT0 for input/output.
Important timing characteristics of the external bus interface (Memory Cycle Time,
Memory Tri-State Time, Length of ALE and Read Write Delay) have been made
programmable to allow the user the adaption of a wide range of different types of
memories and external peripherals.
In addition, up to 4 independent address windows may be defined (via register pairs
ADDRSELx / BUSCONx) which control the access to different resources with different
bus characteristics. These address windows are arranged hierarchically where
BUSCON4 overrides BUSCON3 and BUSCON2 overrides BUSCON1. All accesses to
locations not covered by these 4 address windows are controlled by BUSCON0.
Up to 5 external CS signals (4 windows plus default) can be generated in order to save
external glue logic. The C167CR offers the possibility to switch the CS outputs to an
unlatched mode. In this mode the internal filter logic is switched off and the CS signals
are directly generated from the address. The unlatched CS mode is enabled by setting
CSCFG (SYSCON.6).
Access to very slow memories or memories with varying access times is supported via
a particular ‘Ready’ function.
A HOLD/HLDA protocol is available for bus arbitration and allows to share external
resources with other bus masters. The bus arbitration is enabled by setting bit HLDEN
in register PSW. After setting HLDEN once, pins P6.7 … P6.5 (BREQ, HLDA, HOLD)
are automatically controlled by the EBC. In Master Mode (default after reset) the HLDA
pin is an output. By setting bit DP6.7 to ‘1’ the Slave Mode is selected where pin HLDA
is switched to input. This allows to directly connect the slave controller to another master
controller without glue logic.
For applications which require less than 16 Mbytes of external memory space, this
address space can be restricted to 1 Mbyte, 256 Kbyte, or to 64 Kbyte. In this case Port 4
outputs four, two, or no address lines at all. It outputs all 8 address lines, if an address
space of 16 Mbytes is used.
C167CR
C167SR
Functional Description
Data Sheet 29 V3.3, 2005-02
Note: When the on-chip CAN Module is to be used the segment address output on
Port 4 must be limited to 4 bits (i.e. A19 … A16) in order to enable the alternate
function of the CAN interface pins. CS lines can be used to increase the total
amount of addressable external memory.
C167CR
C167SR
Functional Description
Data Sheet 30 V3.3, 2005-02
3.3 Central Processing Unit (CPU)
The main core of the CPU consists of a 4-stage instruction pipeline, a 16-bit arithmetic
and logic unit (ALU) and dedicated SFRs. Additional hardware has been spent for a
separate multiply and divide unit, a bit-mask generator and a barrel shifter.
Based on these hardware provisions, most of the C167CR’s instructions can be
executed in just one machine cycle which requires 60 ns at 33 MHz CPU clock. For
example, shift and rotate instructions are always processed during one machine cycle
independent of the number of bits to be shifted. All multiple-cycle instructions have been
optimized so that they can be executed very fast as well: branches in 2 cycles, a
16 ×16 bit multiplication in 5 cycles and a 32-/16-bit division in 10 cycles. Another
pipeline optimization, the so-called ‘Jump Cache’, allows reducing the execution time of
repeatedly performed jumps in a loop from 2 cycles to 1 cycle.
Figure 5 CPU Block Diagram
C167CR
C167SR
Functional Description
Data Sheet 31 V3.3, 2005-02
The CPU has a register context consisting of up to 16 wordwide GPRs at its disposal.
These 16 GPRs are physically allocated within the on-chip RAM area. A Context Pointer
(CP) register determines the base address of the active register bank to be accessed by
the CPU at any time. The number of register banks is only restricted by the available
internal RAM space. For easy parameter passing, a register bank may overlap others.
A system stack of up to 1024 words is provided as a storage for temporary data. The
system stack is allocated in the on-chip RAM area, and it is accessed by the CPU via the
stack pointer (SP) register. Two separate SFRs, STKOV and STKUN, are implicitly
compared against the stack pointer value upon each stack access for the detection of a
stack overflow or underflow.
The high performance offered by the hardware implementation of the CPU can efficiently
be utilized by a programmer via the highly efficient C167CR instruction set which
includes the following instruction classes:
Arithmetic Instructions
Logical Instructions
Boolean Bit Manipulation Instructions
Compare and Loop Control Instructions
Shift and Rotate Instructions
Prioritize Instruction
Data Movement Instructions
System Stack Instructions
Jump and Call Instructions
Return Instructions
System Control Instructions
Miscellaneous Instructions
The basic instruction length is either 2 or 4 bytes. Possible operand types are bits, bytes
and words. A variety of direct, indirect or immediate addressing modes are provided to
specify the required operands.
C167CR
C167SR
Functional Description
Data Sheet 32 V3.3, 2005-02
3.4 Interrupt System
With an interrupt response time within a range from just 5 to 12 CPU clocks (in case of
internal program execution), the C167CR is capable of reacting very fast to the
occurrence of non-deterministic events.
The architecture of the C167CR supports several mechanisms for fast and flexible
response to service requests that can be generated from various sources internal or
external to the microcontroller. Any of these interrupt requests can be programmed to
being serviced by the Interrupt Controller or by the Peripheral Event Controller (PEC).
In contrast to a standard interrupt service where the current program execution is
suspended and a branch to the interrupt vector table is performed, just one cycle is
‘stolen’ from the current CPU activity to perform a PEC service. A PEC service implies a
single byte or word data transfer between any two memory locations with an additional
increment of either the PEC source or the destination pointer. An individual PEC transfer
counter is implicity decremented for each PEC service except when performing in the
continuous transfer mode. When this counter reaches zero, a standard interrupt is
performed to the corresponding source related vector location. PEC services are very
well suited, for example, for supporting the transmission or reception of blocks of data.
The C167CR has 8 PEC channels each of which offers such fast interrupt-driven data
transfer capabilities.
A separate control register which contains an interrupt request flag, an interrupt enable
flag and an interrupt priority bitfield exists for each of the possible interrupt sources. Via
its related register, each source can be programmed to one of sixteen interrupt priority
levels. Once having been accepted by the CPU, an interrupt service can only be
interrupted by a higher prioritized service request. For the standard interrupt processing,
each of the possible interrupt sources has a dedicated vector location.
Fast external interrupt inputs are provided to service external interrupts with high
precision requirements. These fast interrupt inputs feature programmable edge
detection (rising edge, falling edge or both edges).
Software interrupts are supported by means of the ‘TRAP’ instruction in combination with
an individual trap (interrupt) number.
Table 4 shows all of the possible C167CR interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers.
Note: Interrupt nodes which are not used by associated peripherals, may be used to
generate software controlled interrupt requests by setting the respective interrupt
request bit (xIR).
C167CR
C167SR
Functional Description
Data Sheet 33 V3.3, 2005-02
Table 4 C167CR Interrupt Nodes
Source of Interrupt or
PEC Service Request
Request
Flag
Enable
Flag
Interrupt
Vector
Vector
Location
Trap
Number
CAPCOM Register 0 CC0IR CC0IE CC0INT 00’0040H10H
CAPCOM Register 1 CC1IR CC1IE CC1INT 00’0044H11H
CAPCOM Register 2 CC2IR CC2IE CC2INT 00’0048H12H
CAPCOM Register 3 CC3IR CC3IE CC3INT 00’004CH13H
CAPCOM Register 4 CC4IR CC4IE CC4INT 00’0050H14H
CAPCOM Register 5 CC5IR CC5IE CC5INT 00’0054H15H
CAPCOM Register 6 CC6IR CC6IE CC6INT 00’0058H16H
CAPCOM Register 7 CC7IR CC7IE CC7INT 00’005CH17H
CAPCOM Register 8 CC8IR CC8IE CC8INT 00’0060H18H
CAPCOM Register 9 CC9IR CC9IE CC9INT 00’0064H19H
CAPCOM Register 10 CC10IR CC10IE CC10INT 00’0068H1AH
CAPCOM Register 11 CC11IR CC11IE CC11INT 00’006CH1BH
CAPCOM Register 12 CC12IR CC12IE CC12INT 00’0070H1CH
CAPCOM Register 13 CC13IR CC13IE CC13INT 00’0074H1DH
CAPCOM Register 14 CC14IR CC14IE CC14INT 00’0078H1EH
CAPCOM Register 15 CC15IR CC15IE CC15INT 00’007CH1FH
CAPCOM Register 16 CC16IR CC16IE CC16INT 00’00C0H30H
CAPCOM Register 17 CC17IR CC17IE CC17INT 00’00C4H31H
CAPCOM Register 18 CC18IR CC18IE CC18INT 00’00C8H32H
CAPCOM Register 19 CC19IR CC19IE CC19INT 00’00CCH33H
CAPCOM Register 20 CC20IR CC20IE CC20INT 00’00D0H34H
CAPCOM Register 21 CC21IR CC21IE CC21INT 00’00D4H35H
CAPCOM Register 22 CC22IR CC22IE CC22INT 00’00D8H36H
CAPCOM Register 23 CC23IR CC23IE CC23INT 00’00DCH37H
CAPCOM Register 24 CC24IR CC24IE CC24INT 00’00E0H38H
CAPCOM Register 25 CC25IR CC25IE CC25INT 00’00E4H39H
CAPCOM Register 26 CC26IR CC26IE CC26INT 00’00E8H3AH
CAPCOM Register 27 CC27IR CC27IE CC27INT 00’00ECH3BH
CAPCOM Register 28 CC28IR CC28IE CC28INT 00’00E0H3CH
CAPCOM Register 29 CC29IR CC29IE CC29INT 00’0110H44H
C167CR
C167SR
Functional Description
Data Sheet 34 V3.3, 2005-02
CAPCOM Register 30 CC30IR CC30IE CC30INT 00’0114H45H
CAPCOM Register 31 CC31IR CC31IE CC31INT 00’0118H46H
CAPCOM Timer 0 T0IR T0IE T0INT 00’0080H20H
CAPCOM Timer 1 T1IR T1IE T1INT 00’0084H21H
CAPCOM Timer 7 T7IR T7IE T7INT 00’00F4H3DH
CAPCOM Timer 8 T8IR T8IE T8INT 00’00F8H3EH
GPT1 Timer 2 T2IR T2IE T2INT 00’0088H22H
GPT1 Timer 3 T3IR T3IE T3INT 00’008CH23H
GPT1 Timer 4 T4IR T4IE T4INT 00’0090H24H
GPT2 Timer 5 T5IR T5IE T5INT 00’0094H25H
GPT2 Timer 6 T6IR T6IE T6INT 00’0098H26H
GPT2 CAPREL Reg. CRIR CRIE CRINT 00’009CH27H
A/D Conversion
Complete
ADCIR ADCIE ADCINT 00’00A0H28H
A/D Overrun Error ADEIR ADEIE ADEINT 00’00A4H29H
ASC0 Transmit S0TIR S0TIE S0TINT 00’00A8H2AH
ASC0 Transmit Buffer S0TBIR S0TBIE S0TBINT 00’011CH47H
ASC0 Receive S0RIR S0RIE S0RINT 00’00ACH2BH
ASC0 Error S0EIR S0EIE S0EINT 00’00B0H2CH
SSC Transmit SCTIR SCTIE SCTINT 00’00B4H2DH
SSC Receive SCRIR SCRIE SCRINT 00’00B8H2EH
SSC Error SCEIR SCEIE SCEINT 00’00BCH2FH
PWM Channel 0 … 3 PWMIR PWMIE PWMINT 00’00FCH3FH
CAN Interface 1 XP0IR XP0IE XP0INT 00’0100H40H
Unassigned node XP1IR XP1IE XP1INT 00’0104H41H
Unassigned node XP2IR XP2IE XP2INT 00’0108H42H
PLL/OWD XP3IR XP3IE XP3INT 00’010CH43H
Table 4 C167CR Interrupt Nodes (cont’d)
Source of Interrupt or
PEC Service Request
Request
Flag
Enable
Flag
Interrupt
Vector
Vector
Location
Trap
Number
C167CR
C167SR
Functional Description
Data Sheet 35 V3.3, 2005-02
The C167CR also provides an excellent mechanism to identify and to process
exceptions or error conditions that arise during run-time, so-called ‘Hardware Traps’.
Hardware traps cause immediate non-maskable system reaction which is similar to a
standard interrupt service (branching to a dedicated vector table location). The
occurrence of a hardware trap is additionally signified by an individual bit in the trap flag
register (TFR). Except when another higher prioritized trap service is in progress, a
hardware trap will interrupt any actual program execution. In turn, hardware trap services
can normally not be interrupted by standard or PEC interrupts.
Table 5 shows all of the possible exceptions or error conditions that can arise during run-
time:
Table 5 Hardware Trap Summary
Exception Condition Trap
Flag
Trap
Vector
Vector
Location
Trap
Number
Trap
Priority
Reset Functions:
Hardware Reset
Software Reset
W-dog Timer Overflow
RESET
RESET
RESET
00’0000H
00’0000H
00’0000H
00H
00H
00H
III
III
III
Class A Hardware Traps:
Non-Maskable Interrupt
Stack Overflow
Stack Underflow
NMI
STKOF
STKUF
NMITRAP
STOTRAP
STUTRAP
00’0008H
00’0010H
00’0018H
02H
04H
06H
II
II
II
Class B Hardware Traps:
Undefined Opcode
Protected Instruction
Fault
Illegal Word Operand
Access
Illegal Instruction
Access
Illegal External Bus
Access
UNDOPC
PRTFLT
ILLOPA
ILLINA
ILLBUS
BTRAP
BTRAP
BTRAP
BTRAP
BTRAP
00’0028H
00’0028H
00’0028H
00’0028H
00’0028H
0AH
0AH
0AH
0AH
0AH
I
I
I
I
I
Reserved [2CH - 3CH][0B
H - 0FH]–
Software Traps
TRAP Instruction
–– Any
[00’0000H -
00’01FCH]
in steps of
4H
Any
[00H - 7FH]
Current
CPU
Priority
C167CR
C167SR
Functional Description
Data Sheet 36 V3.3, 2005-02
3.5 Capture/Compare (CAPCOM) Units
The CAPCOM units support generation and control of timing sequences on up to
32 channels with a maximum resolution of 16 TCL. The CAPCOM units are typically
used to handle high speed I/O tasks such as pulse and waveform generation, pulse
width modulation (PMW), Digital to Analog (D/A) conversion, software timing, or time
recording relative to external events.
Four 16-bit timers (T0/T1, T7/T8) with reload registers provide two independent time
bases for the capture/compare register array.
The input clock for the timers is programmable to several prescaled values of the internal
system clock, or may be derived from an overflow/underflow of timer T6 in module GPT2.
This provides a wide range of variation for the timer period and resolution and allows
precise adjustments to the application specific requirements. In addition, external count
inputs for CAPCOM timers T0 and T7 allow event scheduling for the capture/compare
registers relative to external events.
Both of the two capture/compare register arrays contain 16 dual purpose
capture/compare registers, each of which may be individually allocated to either
CAPCOM timer T0 or T1 (T7 or T8, respectively), and programmed for capture or
compare function. Each register has one port pin associated with it which serves as an
input pin for triggering the capture function, or as an output pin (except for
CC24 CC27) to indicate the occurrence of a compare event.
When a capture/compare register has been selected for capture mode, the current
contents of the allocated timer will be latched (‘captured’) into the capture/compare
register in response to an external event at the port pin which is associated with this
register. In addition, a specific interrupt request for this capture/compare register is
generated. Either a positive, a negative, or both a positive and a negative external signal
transition at the pin can be selected as the triggering event. The contents of all registers
which have been selected for one of the five compare modes are continuously compared
with the contents of the allocated timers. When a match occurs between the timer value
and the value in a capture/compare register, specific actions will be taken based on the
selected compare mode.
C167CR
C167SR
Functional Description
Data Sheet 37 V3.3, 2005-02
Table 6 Compare Modes (CAPCOM)
Compare Modes Function
Mode 0 Interrupt-only compare mode;
several compare interrupts per timer period are possible
Mode 1 Pin toggles on each compare match;
several compare events per timer period are possible
Mode 2 Interrupt-only compare mode;
only one compare interrupt per timer period is generated
Mode 3 Pin set ‘1’ on match; pin reset ‘0’ on compare time overflow;
only one compare event per timer period is generated
Double
Register Mode
Two registers operate on one pin;
pin toggles on each compare match;
several compare events per timer period are possible.
C167CR
C167SR
Functional Description
Data Sheet 38 V3.3, 2005-02
Figure 6 CAPCOM Unit Block Diagram
3.6 PWM Module
The Pulse Width Modulation Module can generate up to four PWM output signals using
edge-aligned or center-aligned PWM. In addition the PWM module can generate PWM
burst signals and single shot outputs. The frequency range of the PWM signals covers
4 Hz to 16.5 MHz (referred to a CPU clock of 33 MHz), depending on the resolution of
the PWM output signal. The level of the output signals is selectable and the PWM
module can generate interrupt requests.
MCB02143B
Mode
Control
(Capture
or
Compare)
2
n
: 1f
CPU
Tx
Input
Control CAPCOM Timer Tx
Ty
Input
Control
TxIN
Interrupt
Request
(TyIR)
GPT2 Timer T6
Over/Underflow
2
n
: 1f
CPU
GPT2 Timer T6
Over/Underflow
CCxIO
CCxIO
16 Capture Inputs
16 Compare Outputs
Reload Reg. TxREL
CAPCOM Timer Ty
Reload Reg. TyREL
Interrupt
Request
(TxIR)
16 Capture/Compare
Interrupt Request
16-Bit
Capture/
Compare
Registers
x = 0, 7
y = 1, 8
n = 3 … 10
C167CR
C167SR
Functional Description
Data Sheet 39 V3.3, 2005-02
3.7 General Purpose Timer (GPT) Unit
The GPT unit represents a very flexible multifunctional timer/counter structure which
may be used for many different time related tasks such as event timing and counting,
pulse width and duty cycle measurements, pulse generation, or pulse multiplication.
The GPT unit incorporates five 16-bit timers which are organized in two separate
modules, GPT1 and GPT2. Each timer in each module may operate independently in a
number of different modes, or may be concatenated with another timer of the same
module.
Each of the three timers T2, T3, T4 of module GPT1 can be configured individually for
one of four basic modes of operation, which are Timer, Gated Timer, Counter, and
Incremental Interface Mode. In Timer Mode, the input clock for a timer is derived from
the CPU clock, divided by a programmable prescaler, while Counter Mode allows a timer
to be clocked in reference to external events.
Pulse width or duty cycle measurement is supported in Gated Timer Mode, where the
operation of a timer is controlled by the ‘gate’ level on an external input pin. For these
purposes, each timer has one associated port pin (TxIN) which serves as gate or clock
input. The maximum resolution of the timers in module GPT1 is 16 TCL.
The count direction (up/down) for each timer is programmable by software or may
additionally be altered dynamically by an external signal on a port pin (TxEUD) to
facilitate e.g. position tracking.
In Incremental Interface Mode the GPT1 timers (T2, T3, T4) can be directly connected
to the incremental position sensor signals A and B via their respective inputs TxIN and
TxEUD. Direction and count signals are internally derived from these two input signals,
so the contents of the respective timer Tx corresponds to the sensor position. The third
position sensor signal TOP0 can be connected to an interrupt input.
Timer T3 has an output toggle latch (T3OTL) which changes its state on each timer over-
flow/underflow. The state of this latch may be output on pin T3OUT e.g. for time out
monitoring of external hardware components, or may be used internally to clock timers
T2 and T4 for measuring long time periods with high resolution.
In addition to their basic operating modes, timers T2 and T4 may be configured as reload
or capture registers for timer T3. When used as capture or reload registers, timers T2
and T4 are stopped. The contents of timer T3 is captured into T2 or T4 in response to a
signal at their associated input pins (TxIN). Timer T3 is reloaded with the contents of T2
or T4 triggered either by an external signal or by a selectable state transition of its toggle
latch T3OTL. When both T2 and T4 are configured to alternately reload T3 on opposite
state transitions of T3OTL with the low and high times of a PWM signal, this signal can
be constantly generated without software intervention.
C167CR
C167SR
Functional Description
Data Sheet 40 V3.3, 2005-02
Figure 7 Block Diagram of GPT1
With its maximum resolution of 8 TCL, the GPT2 module provides precise event control
and time measurement. It includes two timers (T5, T6) and a capture/reload register
(CAPREL). Both timers can be clocked with an input clock which is derived from the CPU
clock via a programmable prescaler or with external signals. The count direction
(up/down) for each timer is programmable by software or may additionally be altered
dynamically by an external signal on a port pin (TxEUD). Concatenation of the timers is
supported via the output toggle latch (T6OTL) of timer T6, which changes its state on
each timer overflow/underflow.
The state of this latch may be used to clock timer T5, and/or it may be output on pin
T6OUT. The overflows/underflows of timer T6 can additionally be used to clock the
CAPCOM timers T0 or T1, and to cause a reload from the CAPREL register. The
CAPREL register may capture the contents of timer T5 based on an external signal
transition on the corresponding port pin (CAPIN), and timer T5 may optionally be cleared
after the capture procedure. This allows the C167CR to measure absolute time
differences or to perform pulse multiplication without software overhead.
T3
Mode
Control
2n : 1fCPU
2n : 1fCPU T2
Mode
Control
GPT1 Timer T2
Reload
Capture
2n : 1fCPU
T4
Mode
Control GPT1 Timer T4
Reload
Capture
GPT1 Timer T3 T3OTL
U/D
T2EUD
T2IN
T3IN
T3EUD
T4IN
T4EUD
T3OUT
Toggle FF
U/D
U/D
Interrupt
Request
Interrupt
Request
Interrupt
Request
Other
Timers
MCT02141
n = 3 … 10
C167CR
C167SR
Functional Description
Data Sheet 41 V3.3, 2005-02
The capture trigger (timer T5 to CAPREL) may also be generated upon transitions of
GPT1 timer T3’s inputs T3IN and/or T3EUD. This is especially advantageous when T3
operates in Incremental Interface Mode.
Figure 8 Block Diagram of GPT2
MUX
2
n
: 1f
CPU
T5
Mode
Control
2
n
: 1f
CPU
T6
Mode
Control
T6OTL
T5EUD
T5IN
T3
CAPIN
T6IN
T6EUD
T6OUT
U/D
U/D
Interrupt
Request
Interrupt
Request
Interrupt
Request
Other
Timers
Clear
Capture
CT3
MCB03999
GPT2 Timer T5
GPT2 CAPREL
GPT2 Timer T6
n = 2 … 9
C167CR
C167SR
Functional Description
Data Sheet 42 V3.3, 2005-02
3.8 A/D Converter
For analog signal measurement, a 10-bit A/D converter with 16 multiplexed input
channels and a sample and hold circuit has been integrated on-chip. It uses the method
of successive approximation. The sample time (for loading the capacitors) and the
conversion time is programmable and can so be adjusted to the external circuitry.
Overrun error detection/protection is provided for the conversion result register
(ADDAT): either an interrupt request will be generated when the result of a previous
conversion has not been read from the result register at the time the next conversion is
complete, or the next conversion is suspended in such a case until the previous result
has been read.
For applications which require less than 16 analog input channels, the remaining
channel inputs can be used as digital input port pins.
The A/D converter of the C167CR supports four different conversion modes. In the
standard Single Channel conversion mode, the analog level on a specified channel is
sampled once and converted to a digital result. In the Single Channel Continuous mode,
the analog level on a specified channel is repeatedly sampled and converted without
software intervention. In the Auto Scan mode, the analog levels on a prespecified
number of channels are sequentially sampled and converted. In the Auto Scan
Continuous mode, the number of prespecified channels is repeatedly sampled and
converted. In addition, the conversion of a specific channel can be inserted (injected) into
a running sequence without disturbing this sequence. This is called Channel Injection
Mode.
The Peripheral Event Controller (PEC) may be used to automatically store the
conversion results into a table in memory for later evaluation, without requiring the
overhead of entering and exiting interrupt routines for each data transfer.
After each reset and also during normal operation the ADC automatically performs
calibration cycles. This automatic self-calibration constantly adjusts the converter to
changing operating conditions (e.g. temperature) and compensates process variations.
These calibration cycles are part of the conversion cycle, so they do not affect the normal
operation of the A/D converter.
In order to decouple analog inputs from digital noise and to avoid input trigger noise
those pins used for analog input can be disconnected from the digital IO or input stages
under software control. This can be selected for each pin separately via register P5DIDIS
(Port 5 Digital Input Disable).
C167CR
C167SR
Functional Description
Data Sheet 43 V3.3, 2005-02
3.9 Serial Channels
Serial communication with other microcontrollers, processors, terminals or external
peripheral components is provided by two serial interfaces with different functionality, an
Asynchronous/Synchronous Serial Channel (ASC0) and a High-Speed Synchronous
Serial Channel (SSC).
The ASC0 is upward compatible with the serial ports of the Infineon 8-bit microcontroller
families and supports full-duplex asynchronous communication at up to
781 kbit/s/1.03 Mbit/s and half-duplex synchronous communication at up to
3.1/4.1 Mbit/s (@ 25/33 MHz CPU clock).
A dedicated baud rate generator allows to set up all standard baud rates without
oscillator tuning. For transmission, reception and error handling 4 separate interrupt
vectors are provided. In asynchronous mode, 8- or 9-bit data frames are transmitted or
received, preceded by a start bit and terminated by one or two stop bits. For
multiprocessor communication, a mechanism to distinguish address from data bytes has
been included (8-bit data plus wake up bit mode).
In synchronous mode, the ASC0 transmits or receives bytes (8 bits) synchronously to a
shift clock which is generated by the ASC0. The ASC0 always shifts the LSB first. A loop
back option is available for testing purposes.
A number of optional hardware error detection capabilities has been included to increase
the reliability of data transfers. A parity bit can automatically be generated on
transmission or be checked on reception. Framing error detection allows to recognize
data frames with missing stop bits. An overrun error will be generated, if the last
character received has not been read out of the receive buffer register at the time the
reception of a new character is complete.
The SSC supports full-duplex synchronous communication at up to 6.25/8.25 Mbit/s
(@ 25/33 MHz CPU clock). It may be configured so it interfaces with serially linked
peripheral components. A dedicated baud rate generator allows to set up all standard
baud rates without oscillator tuning. For transmission, reception, and error handling three
separate interrupt vectors are provided.
The SSC transmits or receives characters of 2 … 16 bits length synchronously to a shift
clock which can be generated by the SSC (master mode) or by an external master (slave
mode). The SSC can start shifting with the LSB or with the MSB and allows the selection
of shifting and latching clock edges as well as the clock polarity.
A number of optional hardware error detection capabilities has been included to increase
the reliability of data transfers. Transmit and receive error supervise the correct handling
of the data buffer. Phase and baudrate error detect incorrect serial data.
C167CR
C167SR
Functional Description
Data Sheet 44 V3.3, 2005-02
3.10 CAN-Module
The integrated CAN-Module handles the completely autonomous transmission and
reception of CAN frames in accordance with the CAN specification V2.0 part B (active),
i.e. the on-chip CAN-Module can receive and transmit standard frames with 11-bit
identifiers as well as extended frames with 29-bit identifiers.
The module provides Full CAN functionality on up to 15 message objects. Message
object 15 may be configured for Basic CAN functionality. Both modes provide separate
masks for acceptance filtering which allows to accept a number of identifiers in Full CAN
mode and also allows to disregard a number of identifiers in Basic CAN mode. All
message objects can be updated independent from the other objects and are equipped
for the maximum message length of 8 bytes.
The bit timing is derived from the XCLK and is programmable up to a data rate of
1 Mbit/s. The CAN-Module uses two pins of Port 4 to interface to an external bus
transceiver.
Note: When the CAN interface is to be used the segment address output on Port 4 must
be limited to 4 bits, i.e. A19 … A16. This is necessary to enable the alternate
function of the CAN interface pins.
3.11 Watchdog Timer
The Watchdog Timer represents one of the fail-safe mechanisms which have been
implemented to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after a reset of the chip, and can only be
disabled in the time interval until the EINIT (end of initialization) instruction has been
executed. Thus, the chip’s start-up procedure is always monitored. The software has to
be designed to service the Watchdog Timer before it overflows. If, due to hardware or
software related failures, the software fails to do so, the Watchdog Timer overflows and
generates an internal hardware reset and pulls the RSTOUT pin low in order to allow
external hardware components to be reset.
The Watchdog Timer is a 16-bit timer, clocked with the system clock divided either by 2
or by 128. The high byte of the Watchdog Timer register can be set to a prespecified
reload value (stored in WDTREL) in order to allow further variation of the monitored time
interval. Each time it is serviced by the application software, the high byte of the
Watchdog Timer is reloaded. Thus, time intervals between 15.5 µs and 254 ms can be
monitored (@ 33 MHz).
The default Watchdog Timer interval after reset is 3.97 ms (@ 33 MHz).
C167CR
C167SR
Functional Description
Data Sheet 45 V3.3, 2005-02
3.12 Parallel Ports
The C167CR provides up to 111 I/O lines which are organized into eight input/output
ports and one input port. All port lines are bit-addressable, and all input/output lines are
individually (bit-wise) programmable as inputs or outputs via direction registers. The I/O
ports are true bidirectional ports which are switched to high impedance state when
configured as inputs. The output drivers of five I/O ports can be configured (pin by pin)
for push/pull operation or open-drain operation via control registers. During the internal
reset, all port pins are configured as inputs.
The input threshold of Port 2, Port 3, Port 6, Port 7, and Port 8 is selectable (TTL or
CMOS like), where the special CMOS like input threshold reduces noise sensitivity due
to the input hysteresis. The input threshold may be selected individually for each byte of
the respective ports.
All port lines have programmable alternate input or output functions associated with
them. All port lines that are not used for these alternate functions may be used as general
purpose IO lines.
PORT0 and PORT1 may be used as address and data lines when accessing external
memory, while Port 4 outputs the additional segment address bits A23/19/17 … A16 in
systems where segmentation is enabled to access more than 64 Kbytes of memory.
Port 2, Port 8 and Port 7 (and parts of PORT1) are associated with the capture inputs or
compare outputs of the CAPCOM units and/or with the outputs of the PWM module.
Port 6 provides optional bus arbitration signals (BREQ, HLDA, HOLD) and chip select
signals.
Port 3 includes alternate functions of timers, serial interfaces, the optional bus control
signal BHE/WRH, and the system clock output (CLKOUT).
Port 5 is used for the analog input channels to the A/D converter or timer control signals.
The edge characteristics (transition time) of the C167CR’s port drivers can be selected
via the Port Driver Control Register (PDCR). Two bits select fast edges (‘0’) or reduced
edges (‘1’) for bus interface pins and non-bus pins separately.
PDCR.0 = BIPEC controls PORT0, PORT1, Port 4, RD, WR, ALE, CLKOUT, BHE/WRH.
PDCR.4 = NBPEC controls Port 3, Port 8, RSTOUT, RSTIN (bidir. reset mode).
C167CR
C167SR
Functional Description
Data Sheet 46 V3.3, 2005-02
3.13 Oscillator Watchdog
The Oscillator Watchdog (OWD) monitors the clock signal generated by the on-chip
oscillator (either with a crystal or via external clock drive). For this operation the PLL
provides a clock signal which is used to supervise transitions on the oscillator clock. This
PLL clock is independent from the XTAL1 clock. When the expected oscillator clock
transitions are missing the OWD activates the PLL Unlock / OWD interrupt node and
supplies the CPU with the PLL clock signal. Under these circumstances the PLL will
oscillate with its basic frequency.
In direct drive mode the PLL base frequency is used directly (fCPU = 2 … 5 MHz).
In prescaler mode the PLL base frequency is divided by 2 (fCPU = 1 … 2.5 MHz).
Note: The CPU clock source is only switched back to the oscillator clock after a
hardware reset.
The oscillator watchdog can be disabled via hardware by (externally) pulling low pin
OWE (internal pull-up provides high level if not connected). In this case (OWE = ‘0’) the
PLL remains idle and provides no clock signal, while the CPU clock signal is derived
directly from the oscillator clock or via prescaler. Also no interrupt request will be
generated in case of a missing oscillator clock.
C167CR
C167SR
Functional Description
Data Sheet 47 V3.3, 2005-02
3.14 Instruction Set Summary
Table 7 lists the instructions of the C167CR in a condensed way.
The various addressing modes that can be used with a specific instruction, the operation
of the instructions, parameters for conditional execution of instructions, and the opcodes
for each instruction can be found in the “C166 Family Instruction Set Manual”.
This document also provides a detailed description of each instruction.
Table 7 Instruction Set Summary
Mnemonic Description Bytes
ADD(B) Add word (byte) operands 2 / 4
ADDC(B) Add word (byte) operands with Carry 2 / 4
SUB(B) Subtract word (byte) operands 2 / 4
SUBC(B) Subtract word (byte) operands with Carry 2 / 4
MUL(U) (Un)Signed multiply direct GPR by direct GPR
(16 × 16 bits)
2
DIV(U) (Un)Signed divide register MDL by direct GPR
(16 / 16 bits)
2
DIVL(U) (Un)Signed long divide reg. MD by direct GPR
(32 / 16 bits)
2
CPL(B) Complement direct word (byte) GPR 2
NEG(B) Negate direct word (byte) GPR 2
AND(B) Bitwise AND, (word/byte operands) 2 / 4
OR(B) Bitwise OR, (word/byte operands) 2 / 4
XOR(B) Bitwise XOR, (word/byte operands) 2 / 4
BCLR Clear direct bit 2
BSET Set direct bit 2
BMOV(N) Move (negated) direct bit to direct bit 4
BAND, BOR,
BXOR
AND/OR/XOR direct bit with direct bit 4
BCMP Compare direct bit to direct bit 4
BFLDH/L Bitwise modify masked high/low byte of bit-addressable
direct word memory with immediate data
4
CMP(B) Compare word (byte) operands 2 / 4
CMPD1/2 Compare word data to GPR and decrement GPR by 1/2 2 / 4
CMPI1/2 Compare word data to GPR and increment GPR by 1/2 2 / 4
C167CR
C167SR
Functional Description
Data Sheet 48 V3.3, 2005-02
PRIOR Determine number of shift cycles to normalize direct
word GPR and store result in direct word GPR
2
SHL / SHR Shift left/right direct word GPR 2
ROL / ROR Rotate left/right direct word GPR 2
ASHR Arithmetic (sign bit) shift right direct word GPR 2
MOV(B) Move word (byte) data 2 / 4
MOVBS Move byte operand to word operand with sign extension 2 / 4
MOVBZ Move byte operand to word operand. with zero extension 2 / 4
JMPA, JMPI,
JMPR
Jump absolute/indirect/relative if condition is met 4
JMPS Jump absolute to a code segment 4
J(N)B Jump relative if direct bit is (not) set 4
JBC Jump relative and clear bit if direct bit is set 4
JNBS Jump relative and set bit if direct bit is not set 4
CALLA, CALLI,
CALLR
Call absolute/indirect/relative subroutine if condition is met 4
CALLS Call absolute subroutine in any code segment 4
PCALL Push direct word register onto system stack and call
absolute subroutine
4
TRAP Call interrupt service routine via immediate trap number 2
PUSH, POP Push/pop direct word register onto/from system stack 2
SCXT Push direct word register onto system stack and update
register with word operand
4
RET Return from intra-segment subroutine 2
RETS Return from inter-segment subroutine 2
RETP Return from intra-segment subroutine and pop direct
word register from system stack
2
RETI Return from interrupt service subroutine 2
SRST Software Reset 4
IDLE Enter Idle Mode 4
PWRDN Enter Power Down Mode (supposes NMI-pin being low) 4
SRVWDT Service Watchdog Timer 4
Table 7 Instruction Set Summary (cont’d)
Mnemonic Description Bytes
C167CR
C167SR
Functional Description
Data Sheet 49 V3.3, 2005-02
DISWDT Disable Watchdog Timer 4
EINIT Signify End-of-Initialization on RSTOUT-pin 4
ATOMIC Begin ATOMIC sequence 2
EXTR Begin EXTended Register sequence 2
EXTP(R) Begin EXTended Page (and Register) sequence 2 / 4
EXTS(R) Begin EXTended Segment (and Register) sequence 2 / 4
NOP Null operation 2
Table 7 Instruction Set Summary (cont’d)
Mnemonic Description Bytes
C167CR
C167SR
Functional Description
Data Sheet 50 V3.3, 2005-02
3.15 Special Function Registers Overview
The following table lists all SFRs which are implemented in the C167CR in alphabetical
order.
Bit-addressable SFRs are marked with the letter “b” in column “Name”. SFRs within the
Extended SFR-Space (ESFRs) are marked with the letter “E” in column “Physical
Address”. Registers within on-chip X-peripherals are marked with the letter “X” in column
“Physical Address”.
An SFR can be specified via its individual mnemonic name. Depending on the selected
addressing mode, an SFR can be accessed via its physical address (using the Data
Page Pointers), or via its short 8-bit address (without using the Data Page Pointers).
Note: Registers within device specific interface modules (CAN) are only present in the
corresponding device, of course.
Table 8 C167CR Registers, Ordered by Name
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
ADCIC b FF98HCCHA/D Converter End of Conversion
Interrupt Control Register
0000H
ADCON b FFA0HD0HA/D Converter Control Register 0000H
ADDAT FEA0H50HA/D Converter Result Register 0000H
ADDAT2 F0A0HE50HA/D Converter 2 Result Register 0000H
ADDRSEL1 FE18H0CHAddress Select Register 1 0000H
ADDRSEL2 FE1AH0DHAddress Select Register 2 0000H
ADDRSEL3 FE1CH0EHAddress Select Register 3 0000H
ADDRSEL4 FE1EH0FHAddress Select Register 4 0000H
ADEIC b FF9AHCDHA/D Converter Overrun Error Interrupt
Control Register
0000H
BUSCON0 b FF0CH86HBus Configuration Register 0 0XX0H
BUSCON1 b FF14H8AHBus Configuration Register 1 0000H
BUSCON2 b FF16H8BHBus Configuration Register 2 0000H
BUSCON3 b FF18H8CHBus Configuration Register 3 0000H
BUSCON4 b FF1AH8DHBus Configuration Register 4 0000H
C1BTR EF04HX CAN1 Bit Timing Register UUUUH
C1CSR EF00HX CAN1 Control / Status Register XX01H
C1GMS EF06HX CAN1 Global Mask Short UFUUH
C167CR
C167SR
Functional Description
Data Sheet 51 V3.3, 2005-02
C1IR EF02HX CAN1 Interrupt Register XXH
C1LGML EF0AHX CAN1 Lower Global Mask Long UUUUH
C1LMLM EF0EHX CAN1 Lower Mask of Last Message UUUUH
C1UAR EFn2HX CAN1 Upper Arbitration Register
(message n)
UUUUH
C1UGML EF08HX CAN1 Upper Global Mask Long UUUUH
C1UMLM EF0CHX CAN1 Upper Mask of Last Message UUUUH
CAPREL FE4AH25HGPT2 Capture/Reload Register 0000H
CC0 FE80H40HCAPCOM Register 0 0000H
CC0IC b FF78HBCHCAPCOM Register 0 Interrupt Ctrl. Reg. 0000H
CC1 FE82H41HCAPCOM Register 1 0000H
CC10 FE94H4AHCAPCOM Register 10 0000H
CC10IC b FF8CHC6HCAPCOM Reg. 10 Interrupt Ctrl. Reg. 0000H
CC11 FE96H4BHCAPCOM Register 11 0000H
CC11IC b FF8EHC7HCAPCOM Reg. 11 Interrupt Ctrl. Reg. 0000H
CC12 FE98H4CHCAPCOM Register 12 0000H
CC12IC b FF90HC8HCAPCOM Reg. 12 Interrupt Ctrl. Reg. 0000H
CC13 FE9AH4DHCAPCOM Register 13 0000H
CC13IC b FF92HC9HCAPCOM Reg. 13 Interrupt Ctrl. Reg. 0000H
CC14 FE9CH4EHCAPCOM Register 14 0000H
CC14IC b FF94HCAHCAPCOM Reg. 14 Interrupt Ctrl. Reg. 0000H
CC15 FE9EH4FHCAPCOM Register 15 0000H
CC15IC b FF96HCBHCAPCOM Reg. 15 Interrupt Ctrl. Reg. 0000H
CC16 FE60H30HCAPCOM Register 16 0000H
CC16IC b F160HEB0HCAPCOM Reg. 16 Interrupt Ctrl. Reg. 0000H
CC17 FE62H31HCAPCOM Register 17 0000H
CC17IC b F162HEB1HCAPCOM Reg. 17 Interrupt Ctrl. Reg. 0000H
CC18 FE64H32HCAPCOM Register 18 0000H
CC18IC b F164HEB2HCAPCOM Reg. 18 Interrupt Ctrl. Reg. 0000H
CC19 FE66H33HCAPCOM Register 19 0000H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 52 V3.3, 2005-02
CC19IC b F166HEB3HCAPCOM Reg. 19 Interrupt Ctrl. Reg. 0000H
CC1IC b FF7AHBDHCAPCOM Reg. 1 Interrupt Ctrl. Reg. 0000H
CC2 FE84H42HCAPCOM Register 2 0000H
CC20 FE68H34HCAPCOM Register 20 0000H
CC20IC b F168HEB4HCAPCOM Reg. 20 Interrupt Ctrl. Reg. 0000H
CC21 FE6AH35HCAPCOM Register 21 0000H
CC21IC b F16AHEB5HCAPCOM Reg. 21 Interrupt Ctrl. Reg. 0000H
CC22 FE6CH36HCAPCOM Register 22 0000H
CC22IC b F16CHEB6HCAPCOM Reg. 22 Interrupt Ctrl. Reg. 0000H
CC23 FE6EH37HCAPCOM Register 23 0000H
CC23IC b F16EHEB7HCAPCOM Reg. 23 Interrupt Ctrl. Reg. 0000H
CC24 FE70H38HCAPCOM Register 24 0000H
CC24IC b F170HEB8HCAPCOM Reg. 24 Interrupt Ctrl. Reg. 0000H
CC25 FE72H39HCAPCOM Register 25 0000H
CC25IC b F172HEB9HCAPCOM Reg. 25 Interrupt Ctrl. Reg. 0000H
CC26 FE74H3AHCAPCOM Register 26 0000H
CC26IC b F174HEBAHCAPCOM Reg. 26 Interrupt Ctrl. Reg. 0000H
CC27 FE76H3BHCAPCOM Register 27 0000H
CC27IC b F176HEBBHCAPCOM Reg. 27 Interrupt Ctrl. Reg. 0000H
CC28 FE78H3CHCAPCOM Register 28 0000H
CC28IC b F178HEBCHCAPCOM Reg. 28 Interrupt Ctrl. Reg. 0000H
CC29 FE7AH3DHCAPCOM Register 29 0000H
CC29IC b F184HEC2HCAPCOM Reg. 29 Interrupt Ctrl. Reg. 0000H
CC2IC b FF7CHBEHCAPCOM Reg. 2 Interrupt Ctrl. Reg. 0000H
CC3 FE86H43HCAPCOM Register 3 0000H
CC30 FE7CH3EHCAPCOM Register 30 0000H
CC30IC b F18CHEC6HCAPCOM Reg. 30 Interrupt Ctrl. Reg. 0000H
CC31 FE7EH3FHCAPCOM Register 31 0000H
CC31IC b F194HECAHCAPCOM Reg. 31 Interrupt Ctrl. Reg. 0000H
CC3IC b FF7EHBFHCAPCOM Reg. 3 Interrupt Ctrl. Reg. 0000H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 53 V3.3, 2005-02
CC4 FE88H44HCAPCOM Register 4 0000H
CC4IC b FF80HC0HCAPCOM Reg. 4 Interrupt Ctrl. Reg. 0000H
CC5 FE8AH45HCAPCOM Register 5 0000H
CC5IC b FF82HC1HCAPCOM Register 5 Interrupt Ctrl. Reg. 0000H
CC6 FE8CH46HCAPCOM Register 6 0000H
CC6IC b FF84HC2HCAPCOM Reg. 6 Interrupt Ctrl. Reg. 0000H
CC7 FE8EH47HCAPCOM Register 7 0000H
CC7IC b FF86HC3HCAPCOM Reg. 7 Interrupt Ctrl. Reg. 0000H
CC8 FE90H48HCAPCOM Register 8 0000H
CC8IC b FF88HC4HCAPCOM Reg. 8 Interrupt Ctrl. Reg. 0000H
CC9 FE92H49HCAPCOM Register 9 0000H
CC9IC b FF8AHC5HCAPCOM Reg. 9 Interrupt Ctrl. Reg. 0000H
CCM0 b FF52HA9HCAPCOM Mode Control Register 0 0000H
CCM1 b FF54HAAHCAPCOM Mode Control Register 1 0000H
CCM2 b FF56HABHCAPCOM Mode Control Register 2 0000H
CCM3 b FF58HACHCAPCOM Mode Control Register 3 0000H
CCM4 b FF22H91HCAPCOM Mode Control Register 4 0000H
CCM5 b FF24H92HCAPCOM Mode Control Register 5 0000H
CCM6 b FF26H93HCAPCOM Mode Control Register 6 0000H
CCM7 b FF28H94HCAPCOM Mode Control Register 7 0000H
CP FE10H08HCPU Context Pointer Register FC00H
CRIC b FF6AHB5HGPT2 CAPREL Interrupt Ctrl. Register 0000H
CSP FE08H04HCPU Code Segment Pointer Register
(read only)
0000H
DP0L b F100HE80HP0L Direction Control Register 00H
DP0H b F102HE81HP0H Direction Control Register 00H
DP1L b F104HE82HP1L Direction Control Register 00H
DP1H b F106HE83HP1H Direction Control Register 00H
DP2 b FFC2HE1HPort 2 Direction Control Register 0000H
DP3 b FFC6HE3HPort 3 Direction Control Register 0000H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 54 V3.3, 2005-02
DP4 b FFCAHE5HPort 4 Direction Control Register 00H
DP6 b FFCEHE7HPort 6 Direction Control Register 00H
DP7 b FFD2HE9HPort 7 Direction Control Register 00H
DP8 b FFD6HEBHPort 8 Direction Control Register 00H
DPP0 FE00H00HCPU Data Page Pointer 0 Reg. (10 bits) 0000H
DPP1 FE02H01HCPU Data Page Pointer 1 Reg. (10 bits) 0001H
DPP2 FE04H02HCPU Data Page Pointer 2 Reg. (10 bits) 0002H
DPP3 FE06H03HCPU Data Page Pointer 3 Reg. (10 bits) 0003H
EXICON b F1C0HEE0HExternal Interrupt Control Register 0000H
MDC b FF0EH87HCPU Multiply Divide Control Register 0000H
MDH FE0CH06HCPU Multiply Divide Reg. – High Word 0000H
MDL FE0EH07HCPU Multiply Divide Reg. – Low Word 0000H
ODP2 b F1C2HEE1HPort 2 Open Drain Control Register 0000H
ODP3 b F1C6HEE3HPort 3 Open Drain Control Register 0000H
ODP6 b F1CEHEE7HPort 6 Open Drain Control Register 00H
ODP7 b F1D2HEE9HPort 7 Open Drain Control Register 00H
ODP8 b F1D6HEEBHPort 8 Open Drain Control Register 00H
ONES FF1EH8FHConstant Value 1’s Register (read only) FFFFH
P0H b FF02H81HPort 0 High Reg. (Upper half of PORT0) 00H
P0L b FF00H80HPort 0 Low Reg. (Lower half of PORT0) 00H
P1H b FF06H83HPort 1 High Reg. (Upper half of PORT1) 00H
P1L b FF04H82HPort 1 Low Reg. (Lower half of PORT1) 00H
P2 b FFC0HE0HPort 2 Register 0000H
P3 b FFC4HE2HPort 3 Register 0000H
P4 b FFC8HE4HPort 4 Register (8 bits) 00H
P5 b FFA2HD1HPort 5 Register (read only) XXXXH
P5DIDIS b FFA4HD2HPort 5 Digital Input Disable Register 0000H
P6 b FFCCHE6HPort 6 Register (8 bits) 00H
P7 b FFD0HE8HPort 7 Register (8 bits) 00H
P8 b FFD4HEAHPort 8 Register (8 bits) 00H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 55 V3.3, 2005-02
PECC0 FEC0H60HPEC Channel 0 Control Register 0000H
PECC1 FEC2H61HPEC Channel 1 Control Register 0000H
PECC2 FEC4H62HPEC Channel 2 Control Register 0000H
PECC3 FEC6H63HPEC Channel 3 Control Register 0000H
PECC4 FEC8H64HPEC Channel 4 Control Register 0000H
PECC5 FECAH65HPEC Channel 5 Control Register 0000H
PECC6 FECCH66HPEC Channel 6 Control Register 0000H
PECC7 FECEH67HPEC Channel 7 Control Register 0000H
PICON b F1C4HEE2HPort Input Threshold Control Register 0000H
PDCR F0AAHE55HPin Driver Control Register 0000H
PP0 F038HE1CHPWM Module Period Register 0 0000H
PP1 F03AHE1DHPWM Module Period Register 1 0000H
PP2 F03CHE1EHPWM Module Period Register 2 0000H
PP3 F03EHE1FHPWM Module Period Register 3 0000H
PSW b FF10H88HCPU Program Status Word 0000H
PT0 F030HE18HPWM Module Up/Down Counter 0 0000H
PT1 F032HE19HPWM Module Up/Down Counter 1 0000H
PT2 F034HE1AHPWM Module Up/Down Counter 2 0000H
PT3 F036HE1BHPWM Module Up/Down Counter 3 0000H
PW0 FE30H18HPWM Module Pulse Width Register 0 0000H
PW1 FE32H19HPWM Module Pulse Width Register 1 0000H
PW2 FE34H1AHPWM Module Pulse Width Register 2 0000H
PW3 FE36H1BHPWM Module Pulse Width Register 3 0000H
PWMCON0 b FF30H98HPWM Module Control Register 0 0000H
PWMCON1 b FF32H99HPWM Module Control Register 1 0000H
PWMIC b F17EHEBFHPWM Module Interrupt Control Register 0000H
RP0H b F108HE84HSystem Start-up Config. Reg. (Rd. only) XXH
S0BG FEB4H5AHSerial Channel 0 Baudrate Generator
Reload Register
0000H
S0CON b FFB0HD8HSerial Channel 0 Control Register 0000H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 56 V3.3, 2005-02
S0EIC b FF70HB8HSerial Chan. 0 Error Interrupt Ctrl. Reg. 0000H
S0RBUF FEB2H59HSerial Channel 0 Receive Buffer Reg.
(read only)
XXH
S0RIC b FF6EHB7HSerial Channel 0 Receive Interrupt
Control Register
0000H
S0TBIC b F19CHECEHSerial Channel 0 Transmit Buffer
Interrupt Control Register
0000H
S0TBUF FEB0H58HSerial Channel 0 Transmit Buffer Reg.
(write only)
00H
S0TIC b FF6CHB6HSerial Channel 0 Transmit Interrupt
Control Register
0000H
SP FE12H09HCPU System Stack Pointer Register FC00H
SSCBR F0B4HE5AHSSC Baudrate Register 0000H
SSCCON b FFB2HD9HSSC Control Register 0000H
SSCEIC b FF76HBBHSSC Error Interrupt Control Register 0000H
SSCRB F0B2HE59HSSC Receive Buffer XXXXH
SSCRIC b FF74HBAHSSC Receive Interrupt Control Register 0000H
SSCTB F0B0HE58HSSC Transmit Buffer 0000H
SSCTIC b FF72HB9HSSC Transmit Interrupt Control Register 0000H
STKOV FE14H0AHCPU Stack Overflow Pointer Register FA00H
STKUN FE16H0BHCPU Stack Underflow Pointer Register FC00H
SYSCON b FF12H89HCPU System Configuration Register 1)0xx0H
T0 FE50H28HCAPCOM Timer 0 Register 0000H
T01CON b FF50HA8HCAPCOM Timer 0 and Timer 1 Ctrl. Reg. 0000H
T0IC b FF9CHCEHCAPCOM Timer 0 Interrupt Ctrl. Reg. 0000H
T0REL FE54H2AHCAPCOM Timer 0 Reload Register 0000H
T1 FE52H29HCAPCOM Timer 1 Register 0000H
T1IC b FF9EHCFHCAPCOM Timer 1 Interrupt Ctrl. Reg. 0000H
T1REL FE56H2BHCAPCOM Timer 1 Reload Register 0000H
T2 FE40H20HGPT1 Timer 2 Register 0000H
T2CON b FF40HA0HGPT1 Timer 2 Control Register 0000H
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Functional Description
Data Sheet 57 V3.3, 2005-02
T2IC b FF60HB0HGPT1 Timer 2 Interrupt Control Register 0000H
T3 FE42H21HGPT1 Timer 3 Register 0000H
T3CON b FF42HA1HGPT1 Timer 3 Control Register 0000H
T3IC b FF62HB1HGPT1 Timer 3 Interrupt Control Register 0000H
T4 FE44H22HGPT1 Timer 4 Register 0000H
T4CON b FF44HA2HGPT1 Timer 4 Control Register 0000H
T4IC b FF64HB2HGPT1 Timer 4 Interrupt Control Register 0000H
T5 FE46H23HGPT2 Timer 5 Register 0000H
T5CON b FF46HA3HGPT2 Timer 5 Control Register 0000H
T5IC b FF66HB3HGPT2 Timer 5 Interrupt Control Register 0000H
T6 FE48H24HGPT2 Timer 6 Register 0000H
T6CON b FF48HA4HGPT2 Timer 6 Control Register 0000H
T6IC b FF68HB4HGPT2 Timer 6 Interrupt Control Register 0000H
T7 F050HE28HCAPCOM Timer 7 Register 0000H
T78CON b FF20H90HCAPCOM Timer 7 and 8 Ctrl. Reg. 0000H
T7IC b F17AHEBEHCAPCOM Timer 7 Interrupt Ctrl. Reg. 0000H
T7REL F054HE2AHCAPCOM Timer 7 Reload Register 0000H
T8 F052HE29HCAPCOM Timer 8 Register 0000H
T8IC b F17CHEBFHCAPCOM Timer 8 Interrupt Ctrl. Reg. 0000H
T8REL F056HE2BHCAPCOM Timer 8 Reload Register 0000H
TFR b FFACHD6HTrap Flag Register 0000H
WDT FEAEH57HWatchdog Timer Register (read only) 0000H
WDTCON FFAEHD7HWatchdog Timer Control Register 2)00XXH
XP0IC b F186HEC3HCAN1 Module Interrupt Control Register 0000H
XP1IC b F18EHEC7HUnassigned Interrupt Control Register 0000H
XP2IC b F196HECBHUnassigned Interrupt Control Register 0000H
XP3IC b F19EHECFHPLL/OWD Interrupt Control Register 0000H
ZEROS b FF1CH8EHConstant Value 0’s Register (read only) 0000H
1) The system configuration is selected during reset.
2) The reset value depends on the indicated reset source.
Table 8 C167CR Registers, Ordered by Name (cont’d)
Name Physical
Address
8-Bit
Addr.
Description Reset
Value
C167CR
C167SR
Electrical Parameters
Data Sheet 58 V3.3, 2005-02
4 Electrical Parameters
4.1 General Parameters
Note: Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
During absolute maximum rating overload conditions (VIN > VDD or VIN < VSS) the
voltage on VDD pins with respect to ground (VSS) must not exceed the values
defined by the absolute maximum ratings.
Table 9 Absolute Maximum Rating Parameters
Parameter Symbol Limit Values Unit Notes
Min. Max.
Storage temperature TST -65 150 °C–
Junction temperature TJ-40 150 °C under bias
Voltage on VDD pins with
respect to ground (VSS)
VDD -0.5 6.5 V
Voltage on any pin with
respect to ground (VSS)
VIN -0.5 VDD + 0.5 V
Input current on any pin
during overload condition
–-1010mA
Absolute sum of all input
currents during overload
condition
–– |100|mA
Power dissipation PDISS –1.5W
C167CR
C167SR
Electrical Parameters
Data Sheet 59 V3.3, 2005-02
Operating Conditions
The following operating conditions must not be exceeded in order to ensure correct
operation of the C167CR. All parameters specified in the following sections refer to these
operating conditions, unless otherwise noticed.
Table 10 Operating Condition Parameters
Parameter Symbol Limit Values Unit Notes
Min. Max.
Digital supply voltage VDD 4.5 5.5 V Active mode,
fCPUmax = 33 MHz
2.51)
1) Output voltages and output currents will be reduced when VDD leaves the range defined for active mode.
5.5 V Power Down mode
Digital ground voltage VSS 0 V Reference voltage
Overload current IOV ±5mAPer pin
2)3)
2) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
exceeds the specified range (i.e. VOV > VDD + 0.5 V or VOV < VSS - 0.5 V). The absolute sum of input overload
currents on all pins may not exceed 50 mA. The supply voltage must remain within the specified limits.
Proper operation is not guaranteed if overload conditions occur on functional pins like XTAL1, RD, WR, etc.
3) Not subject to production test - verified by design/characterization.
Absolute sum of overload
currents
Σ|IOV|– 50 mA
3)
External Load Capacitance CL 50 pF Pin drivers in
fast edge mode
(PDCR.BIPEC = ‘0’)
30 pF Pin drivers in
reduced edge mode
(PDCR.BIPEC = ‘1’)3)
100 pF Pin drivers in
fast edge mode,
fCPUmax = 25 MHz4)
4) The increased capacitive load is valid for the 25 MHz-derivatives up to a CPU clock frequency of 25 MHz.
Under these circumstances the timing parameters as specified in the “C167CR Data Sheet 1999-06” are valid.
Ambient temperature TA070°C SAB-C167CR …
-40 85 °C SAF-C167CR …
-40 125 °C SAK-C167CR …
C167CR
C167SR
Electrical Parameters
Data Sheet 60 V3.3, 2005-02
Parameter Interpretation
The parameters listed in the following partly represent the characteristics of the C167CR
and partly its demands on the system. To aid in interpreting the parameters right, when
evaluating them for a design, they are marked in column “Symbol”:
CC (Controller Characteristics):
The logic of the C167CR will provide signals with the respective timing characteristics.
SR (System Requirement):
The external system must provide signals with the respective timing characteristics to
the C167CR.
4.2 DC Parameters
Table 11 DC Characteristics (Operating Conditions apply)1)
Parameter Symbol Limit Values Unit Test Condition
Min. Max.
Input low voltage (TTL,
all except XTAL1)
VIL SR -0.5 0.2 VDD
- 0.1
V–
Input low voltage XTAL1 VIL2 SR -0.5 0.3 VDD V–
Input low voltage
(Special Threshold)
VILS SR -0.5 2.0 V
Input high voltage (TTL,
all except RSTIN and XTAL1)
VIH SR 0.2 VDD
+ 0.9
VDD +
0.5
V–
Input high voltage RSTIN
(when operated as input)
VIH1 SR 0.6 VDD VDD +
0.5
V–
Input high voltage XTAL1 VIH2 SR 0.7 VDD VDD +
0.5
V–
Input high voltage
(Special Threshold)
VIHS SR 0.8 VDD
- 0.2
VDD +
0.5
V–
Input Hysteresis
(Special Threshold)
HYS 400 mV Series
resistance = 0
Output low voltage
(PORT0, PORT1, Port 4, ALE,
RD, WR, BHE, CLKOUT,
RSTOUT, RSTIN2))
VOL CC 0.45 V IOL = 2.4 mA
Output low voltage
(all other outputs)
VOL1 CC 0.45 V IOL = 1.6 mA
C167CR
C167SR
Electrical Parameters
Data Sheet 61 V3.3, 2005-02
Output high voltage3)
(PORT0, PORT1, Port 4, ALE,
RD, WR, BHE, CLKOUT,
RSTOUT)
VOH CC 2.4 V IOH = -2.4 mA
0.9 VDD –VIOH = -0.5 mA
Output high voltage3)
(all other outputs)
VOH1 CC 2.4 V IOH = -1.6 mA
0.9 VDD –VIOH = -0.5 mA
Input leakage current (Port 5) IOZ1 CC ±200 nA 0 V < VIN < VDD
Input leakage current
(all other)4)
IOZ2 CC ±500 nA 0.45 V < VIN <
VDD
RSTIN inactive current5) IRSTH
6) –-10µAVIN = VIH1
RSTIN active current5) IRSTL
7) -100 µAVIN = VIL
READY/RD/WR inact. current8) IRWH
6) –-40µAVOUT = 2.4 V
READY/RD/WR active current8) IRWL
7) -500 µAVOUT = VOLmax
ALE inactive current8) IALEL
6) –40µAVOUT = VOLmax
ALE active current8) IALEH
7) 500 µAVOUT = 2.4 V
Port 6 inactive current8) IP6H
6) –-40µAVOUT = 2.4 V
Port 6 active current8) IP6L
7) -500 µAVOUT = VOL1max
PORT0 configuration current9) IP0H
6) –-10µAVIN = VIHmin
IP0L
7) -100 µAVIN = VILmax
XTAL1 input current IIL CC ±20 µA0 V < VIN < VDD
Pin capacitance10)
(digital inputs/outputs)
CIO CC 10 pF f = 1 MHz;
TA = 25 °C
1) Keeping signal levels within the levels specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications also refer to the specification of the overload current IOV.
2) Valid in bidirectional reset mode only.
3) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
4) This parameter is not valid for pins READY, ALE, RD, and WR while the respective pull device is on.
5) These parameters describe the RSTIN pull-up, which equals a resistance of ca. 50 to 250 k.
6) The maximum current may be drawn while the respective signal line remains inactive.
7) The minimum current must be drawn in order to drive the respective signal line active.
8) This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins
are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The
READY-pull-up is always active, except for Power-down mode.
Table 11 DC Characteristics (Operating Conditions apply)1) (cont’d)
Parameter Symbol Limit Values Unit Test Condition
Min. Max.
C167CR
C167SR
Electrical Parameters
Data Sheet 62 V3.3, 2005-02
9) This specification is valid during Reset and during Adapt-mode.
10) Not subject to production test - verified by design/characterization.
Table 12 Power Consumption C167CR (Operating Conditions apply)
Parameter Symbol Limit Values Unit Test Condition
Min. Max.
Power supply current (active)
with all peripherals active
IDD –15 + 2.5
× fCPU
mA RSTIN = VIL
fCPU in [MHz]1)
1) The supply current is a function of the operating frequency. This dependency is illustrated in Figure 9.
These parameters are tested at VDDmax and maximum CPU clock with all outputs disconnected and all inputs
at VIL or VIH.
Idle mode supply current IID –10 + 1.0
× fCPU
mA RSTIN = VIH1
fCPU in [MHz]1)
Power-down mode supply
current
IPD –50 µAVDD = VDDmax
2)
2) This parameter is tested including leakage currents. All inputs (including pins configured as inputs) at 0 V to
0.1 V or at VDD - 0.1 V to VDD, all outputs (including pins configured as outputs) disconnected.
C167CR
C167SR
Electrical Parameters
Data Sheet 63 V3.3, 2005-02
Figure 9 Supply/Idle Current as a Function of Operating Frequency
I [mA]
fCPU [MHz]
10 20 30 40
IDDmax
IDDtyp
IIDmax
IIDtyp
20
40
60
80
100
120
140
C167CR
C167SR
Electrical Parameters
Data Sheet 64 V3.3, 2005-02
4.3 Analog/Digital Converter Parameters
Table 13 A/D Converter Characteristics (Operating Conditions apply)
Parameter Symbol Limit Values Unit Test
Condition
Min. Max.
Analog reference supply VAREF SR 4.0 VDD + 0.1 V 1)
1) TUE is tested at VAREF = 5.0 V, VAGND = 0 V, VDD = 4.9 V. It is guaranteed by design for all other voltages within
the defined voltage range.
If the analog reference supply voltage exceeds the power supply voltage by up to 0.2 V
(i.e. VAREF = VDD + 0.2 V) the maximum TUE is increased to ±3 LSB. This range is not 100% tested.
The specified TUE is guaranteed only if the absolute sum of input overload currents on Port 5 pins (see IOV
specification) does not exceed 10 mA.
During the reset calibration sequence the maximum TUE may be ±4 LSB.
Analog reference ground VAGNDSR VSS - 0.1 VSS + 0.2 V
Analog input voltage range VAIN SR VAGND VAREF V2)
2) VAIN may exceed VAGND or VAREF up to the absolute maximum ratings. However, the conversion result in these
cases will be X000H or X3FFH, respectively.
Basic clock frequency fBC 0.5 6.25 MHz 3)
3) The limit values for fBC must not be exceeded when selecting the CPU frequency and the ADCTC setting.
Conversion time tCCC 40 tBC + tS
+ 2 tCPU
4)
tCPU = 1/fCPU
4) This parameter includes the sample time tS, the time for determining the digital result and the time to load the
result register with the conversion result.
Values for the basic clock tBC depend on programming and can be taken from Table 14.
This parameter depends on the ADC control logic. It is not a real maximum value, but rather a fixum.
Calibration time after reset tCAL CC 3328 tBC 5)
5) During the reset calibration conversions can be executed (with the current accuracy). The time required for
these conversions is added to the total reset calibration time.
Total unadjusted error TUE CC ±2LSB
1)
Internal resistance of
reference voltage source
RAREF SR tBC / 60
- 0.25
ktBC in [ns]6)7)
6) During the conversion the ADC’s capacitance must be repeatedly charged or discharged. The internal
resistance of the reference voltage source must allow the capacitance to reach its respective voltage level
within each conversion step. The maximum internal resistance results from the programmed conversion
timing.
7) Not subject to production test - verified by design/characterization.
Internal resistance of
analog source
RASRC SR tS / 450
- 0.25
ktS in [ns]7)8)
ADC input capacitance CAIN CC 33 pF 7)
C167CR
C167SR
Electrical Parameters
Data Sheet 65 V3.3, 2005-02
Sample time and conversion time of the C167CR’s A/D Converter are programmable.
Table 14 should be used to calculate the above timings.
The limit values for fBC must not be exceeded when selecting ADCTC.
Converter Timing Example:
8) During the sample time the input capacitance CAIN can be charged/discharged by the external source. The
internal resistance of the analog source must allow the capacitance to reach its final voltage level within tS.
After the end of the sample time tS, changes of the analog input voltage have no effect on the conversion
result.
Values for the sample time tS depend on programming and can be taken from Table 14.
Table 14 A/D Converter Computation Table
ADCON.15|14
(ADCTC)
A/D Converter
Basic clock fBC
ADCON.13|12
(ADSTC)
Sample time
tS
00 fCPU / 4 00 tBC × 8
01 fCPU / 2 01 tBC × 16
10 fCPU / 16 10 tBC × 32
11 fCPU / 8 11 tBC × 64
Assumptions: fCPU = 25 MHz (i.e. tCPU = 40 ns), ADCTC = ‘00’, ADSTC = ‘00’
Basic clock fBC = fCPU / 4 = 6.25 MHz, i.e. tBC = 160 ns
Sample time tS= tBC × 8 = 1280 ns
Conversion
time
tC= tS + 40 tBC + 2 tCPU = (1280 + 6400 + 80) ns = 7.8 µs
C167CR
C167SR
Electrical Parameters
Data Sheet 66 V3.3, 2005-02
4.4 AC Parameters
4.4.1 Definition of Internal Timing
The internal operation of the C167CR is controlled by the internal CPU clock fCPU. Both
edges of the CPU clock can trigger internal (e.g. pipeline) or external (e.g. bus cycles)
operations.
The specification of the external timing (AC Characteristics) therefore depends on the
time between two consecutive edges of the CPU clock, called “TCL” (see Figure 10).
Figure 10 Generation Mechanisms for the CPU Clock
The CPU clock signal fCPU can be generated from the oscillator clock signal fOSC via
different mechanisms. The duration of TCLs and their variation (and also the derived
external timing) depends on the used mechanism to generate fCPU. This influence must
be regarded when calculating the timings for the C167CR.
Note: The example for PLL operation shown in the fig. above refers to a PLL factor of 4.
The used mechanism to generate the basic CPU clock is selected by bitfield CLKCFG
in register RP0H.7-5.
Upon a long hardware reset register RP0H is loaded with the logic levels present on the
MCT04338
f
OSC
f
CPU
Phase Locked Loop Operation
TCL
f
OSC
f
CPU
Direct Clock Drive
f
OSC
f
CPU
Prescaler Operation
TCL
TCL
TCL
TCL
TCL
C167CR
C167SR
Electrical Parameters
Data Sheet 67 V3.3, 2005-02
upper half of PORT0 (P0H), i.e. bitfield CLKCFG represents the logic levels on pins
P0.15-13 (P0H.7-5).
Table 15 associates the combinations of these three bits with the respective clock
generation mode.
Prescaler Operation
When prescaler operation is configured (CLKCFG = 001B) the CPU clock is derived from
the internal oscillator (input clock signal) by a 2:1 prescaler.
The frequency of fCPU is half the frequency of fOSC and the high and low time of fCPU (i.e.
the duration of an individual TCL) is defined by the period of the input clock fOSC.
The timings listed in the AC Characteristics that refer to TCLs therefore can be
calculated using the period of fOSC for any TCL.
Phase Locked Loop
When PLL operation is configured (via CLKCFG) the on-chip phase locked loop is
enabled and provides the CPU clock (see table above). The PLL multiplies the input
frequency by the factor F which is selected via the combination of pins P0.15-13 (i.e. fCPU
= fOSC × F). With every F’th transition of fOSC the PLL circuit synchronizes the CPU clock
to the input clock. This synchronization is done smoothly, i.e. the CPU clock frequency
does not change abruptly.
Due to this adaptation to the input clock the frequency of fCPU is constantly adjusted so
it is locked to fOSC. The slight variation causes a jitter of fCPU which also effects the
duration of individual TCLs.
Table 15 C167CR Clock Generation Modes
CLKCFG
(P0H.7-5)
CPU Frequency
fCPU = fOSC × F
External Clock
Input Range1)
1) The external clock input range refers to a CPU clock range of 10 … 33 MHz (PLL operation).
Notes
1 1 1 fOSC × 4 2.5 to 8.25 MHz Default configuration
1 1 0 fOSC × 3 3.33 to 11 MHz
1 0 1 fOSC × 2 5 to 16.5 MHz
1 0 0 fOSC × 5 2 to 6.6 MHz
0 1 1 fOSC × 1 1 to 33 MHz Direct drive2)
2) The maximum frequency depends on the duty cycle of the external clock signal.
0 1 0 fOSC × 1.5 6.66 to 22 MHz
0 0 1 fOSC / 2 2 to 66 MHz CPU clock via prescaler
0 0 0 fOSC × 2.5 4 to 13.2 MHz
C167CR
C167SR
Electrical Parameters
Data Sheet 68 V3.3, 2005-02
The timings listed in the AC Characteristics that refer to TCLs therefore must be
calculated using the minimum TCL that is possible under the respective circumstances.
The actual minimum value for TCL depends on the jitter of the PLL. As the PLL is
constantly adjusting its output frequency so it corresponds to the applied input frequency
(crystal or oscillator) the relative deviation for periods of more than one TCL is lower than
for one single TCL (see formula and Figure 11).
For a period of N×TCL the minimum value is computed using the corresponding
deviation DN:
(N × TCL)min = N × TCLNOM - DN, DN [ns] = ±(13.3 + N × 6.3) / fCPU [MHz], (1)
where N = number of consecutive TCLs and 1 N 40.
So for a period of 3 TCLs @ 25 MHz (i.e. N = 3): D3 = (13.3 + 3 × 6.3) / 25 = 1.288 ns,
and (3TCL)min = 3TCLNOM - 1.288 ns = 58.7 ns (@ fCPU = 25 MHz).
This is especially important for bus cycles using waitstates and e.g. for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is negligible.
Note: For all periods longer than 40 TCL the N = 40 value can be used (see Figure 11).
Figure 11 Approximated Maximum Accumulated PLL Jitter
±1
±10
1 5 10 20
D
N
±20
±26.5
ns
±30
40 and 10 MHz
This approximated formula is valid for
1N33 MHz.
CPU
f
25 MHz
33 MHz
40
MCD04413
N
16 MHz
20 MHz
10 MHz
Max. jitter
C167CR
C167SR
Electrical Parameters
Data Sheet 69 V3.3, 2005-02
Direct Drive
When direct drive is configured (CLKCFG = 011B) the on-chip phase locked loop is
disabled and the CPU clock is directly driven from the internal oscillator with the input
clock signal.
The frequency of fCPU directly follows the frequency of fOSC so the high and low time of
fCPU (i.e. the duration of an individual TCL) is defined by the duty cycle of the input clock
fOSC.
The timings listed below that refer to TCLs therefore must be calculated using the
minimum TCL that is possible under the respective circumstances. This minimum value
can be calculated via the following formula:
TCLmin = 1/fOSC × DCmin (DC = duty cycle) (2)
For two consecutive TCLs the deviation caused by the duty cycle of fOSC is compensated
so the duration of 2TCL is always 1/fOSC. The minimum value TCLmin therefore has to be
used only once for timings that require an odd number of TCLs (1, 3, …). Timings that
require an even number of TCLs (2, 4, …) may use the formula 2TCL = 1/fOSC.
C167CR
C167SR
Electrical Parameters
Data Sheet 70 V3.3, 2005-02
4.4.2 External Clock Drive XTAL1
Figure 12 External Clock Drive XTAL1
Note: If the on-chip oscillator is used together with a crystal, the oscillator frequency is
limited to a range of 4 MHz to 40 MHz.
It is strongly recommended to measure the oscillation allowance (or margin) in the
final target system (layout) to determine the optimum parameters for the oscillator
operation. Please refer to the limits specified by the crystal supplier.
When driven by an external clock signal it will accept the specified frequency
range. Operation at lower input frequencies is possible but is guaranteed by
design only (not 100% tested).
Table 16 External Clock Drive Characteristics (Operating Conditions apply)
Parameter Symbol Direct Drive
1:1
Prescaler
2:1
PLL
1:N
Unit
Min. Max. Min. Max. Min. Max.
Oscillator period tOSC SR 30 15 451)
1) The minimum and maximum oscillator periods for PLL operation depend on the selected CPU clock
generation mode. Please see respective table above.
5001) ns
High time2)
2) The clock input signal must reach the defined levels VIL2 and VIH2.
t1SR 153)
3) The minimum high and low time refers to a duty cycle of 50%. The maximum operating frequency (fCPU) in
direct drive mode depends on the duty cycle of the clock input signal.
–5–10–ns
Low time2) t2SR 153) –5–10–ns
Rise time2) t3SR–8–5–10ns
Fall time2) t4SR–8–5–10ns
MCT02534
3
t4
t
VIH2
VIL
VDD
0.5
1
t
2
t
OSC
t
C167CR
C167SR
Electrical Parameters
Data Sheet 71 V3.3, 2005-02
4.4.3 Testing Waveforms
Figure 13 Input Output Waveforms
Figure 14 Float Waveforms
MCA04414
2.4 V
0.45 V
1.8 V
0.8 V
1.8 V
0.8 V
Test Points
AC inputs during testing are driven at 2.4 V for a logic ’1’ and 0.45 V for a logic ’0’.
Timing measurements are made at IH
V
min for a logic ’1’ and
V
IL max for a logic ’0’.
MCA00763
- 0.1 V
+ 0.1 V
+ 0.1 V
- 0.1 V
Reference
For timing purposes a port pin is no longer floating when a 100 mV change from load voltage occurs,
but begins to float when a 100 mV change from the loaded
OH
V
Timing
Points
Load
V
V
Load
OH
V
V
OL
/
V
OL
level occurs (
I
OH OL
I
/ = 20 mA).
C167CR
C167SR
Electrical Parameters
Data Sheet 72 V3.3, 2005-02
4.4.4 External Bus Timing
Figure 15 CLKOUT Signal Timing
Variable Memory Cycles
The bus timing shown below is programmable via the BUSCONx registers. The duration
of ALE and two types of waitstates can be selected. This table summarizes the possible
bus cycle durations.
Table 17 CLKOUT Reference Signal
Parameter Symbol Limits Unit
Min. Max.
CLKOUT cycle time tc5CC 301)
1) The CLKOUT cycle time is influenced by the PLL jitter.
For a single CLKOUT cycle (2 TCL) the deviation caused by the PLL jitter is below 1 ns (for fCPU > 25 MHz).
For longer periods the relative deviation decreases (see PLL deviation formula).
ns
CLKOUT high time tc6CC 8 ns
CLKOUT low time tc7CC 6 ns
CLKOUT rise time tc8CC 4 ns
CLKOUT fall time tc9CC 4 ns
Table 18 Variable Memory Cycles
Bus Cycle Type Bus Cycle Duration Unit 25/33 MHz, 0 Waitstates
Demultiplexed bus cycle
with normal ALE
4 + 2 × (15 - <MCTC>)
+ 2 × (1 - <MTTC>)
TCL 80 ns/60.6 ns
Demultiplexed bus cycle
with extended ALE
6 + 2 × (15 - <MCTC>)
+ 2 × (1 - <MTTC>)
TCL 120 ns/90.9 ns
Multiplexed bus cycle with
normal ALE
6 + 2 × (15 - <MCTC>)
+ 2 × (1 - <MTTC>)
TCL 120 ns/90.9 ns
Multiplexed bus cycle with
extended ALE
8 + 2 × (15 - <MCTC>)
+ 2 × (1 - <MTTC>)
TCL 160 ns/121.2 ns
MCT04415
CLKOUT
tc
5
tc
6
7
tc
8
tc
9
tc
C167CR
C167SR
Electrical Parameters
Data Sheet 73 V3.3, 2005-02
Table 19 External Bus Cycle Timing (Operating Conditions apply)
Parameter Symbol Limits Unit
Min. Max.
Output delay from CLKOUT falling edge
Valid for: address, BHE, early CS, write data out, ALE
tc10 CC -2 11 ns
Output delay from CLKOUT rising edge
Valid for: latched CS, ALE low
tc11 CC -2 6 ns
Output delay from CLKOUT rising edge
Valid for: WR low (no RW delay), RD low (no RW
delay)
tc12 CC -2 8 ns
Output delay from CLKOUT falling edge
Valid for: RD/WR low (with RW delay), RD high (with
RW delay)
tc13 CC -2 6 ns
Input setup time to CLKOUT falling edge
Valid for: read data in
tc14 SR 14 ns
Input hold time after CLKOUT falling edge
Valid for: read data in1)
1) Read data are latched with the same (internal) clock edge that triggers the address change and the rising edge
of RD. Therefore the read data may be removed immediately after the rising edge of RD. Address changes
before the end of RD have also no impact on (demultiplexed) read cycles.
tc15 SR 0 ns
Output hold time after CLKOUT falling edge
Valid for: address, BHE, early CS2)
2) Due to comparable propagation delays (at comparable capacitive loads) the address does not change before
WR goes high. The minimum output delay (tc17min) is therefore the actual value of tc19.
tc17 CC -2 6 ns
Output hold time after CLKOUT edge3)
Valid for: write data out
3) Not subject to production test - verified by design/characterization.
tc18 CC -2 ns
Output delay from CLKOUT falling edge
Valid for: WR high
tc19 CC -2 4 ns
Turn off delay after CLKOUT edge3)
Valid for: write data out
tc20 CC 7 ns
Turn on delay after CLKOUT falling edge3)
Valid for: write data out
tc21 CC -5 ns
C167CR
C167SR
Electrical Parameters
Data Sheet 74 V3.3, 2005-02
General Notes for the Following Timing Figures
These standard notes apply to all subsequent timing figures. Additional individual notes
are placed at the respective figure.
1. The falling edge of signals RD and WR/WRH/WRL/WrCS is controlled by the
Read/Write delay feature (bit BUSCON.RWDCx).
2. A bus cycle is extended here, if MCTC waitstates are selected or if the READY input
is sampled inactive.
3. A bus cycle is extended here, if an MTTC waitstate is selected.
C167CR
C167SR
Electrical Parameters
Data Sheet 75 V3.3, 2005-02
Figure 16 Demultiplexed Bus, Write Access
D15-D0
WR, WrCS
BHE, CSxE
WRL, WRH,
A23-A0
tc
10
MCT04416
MCTC
1)
2)
tc
tc
21
10
tc
tc
10
tc
12
13
Valid
tc
Data OUT
MTTC
3)
tc
18
20
tc
19
tc
17
tc
Extended ALE
CSxL
tc
10
Normal ALE
CLKOUT
tc
Extended ALE Cycle
11
10
tc
11
tc
tc
10
11
Normal ALE Cycle
tc
11
C167CR
C167SR
Electrical Parameters
Data Sheet 76 V3.3, 2005-02
Figure 17 Demultiplexed Bus, Read Access
11
Normal ALE Cycle
11
Extended ALE Cycle
12
RdCS
D15-D0
A23-A0,
RD,
BHE, CSxE
10
tc tc
tc
10
Extended ALE
CSxL
CLKOUT
Normal ALE
tc
tc
10
11
tc
10
tc
tc
tc
10
tc
1)
2)
MCTC
13
tc
Valid
MTTC
3)
Data IN
tc
14
15
tc
13
tc
17
MCT04417
tc
11
C167CR
C167SR
Electrical Parameters
Data Sheet 77 V3.3, 2005-02
Figure 18 Multiplexed Bus, Write Access
20
20
MCT04418
AD15-AD0
(Extended ALE)
AD15-AD0
(Normal ALE)
WR, WrCS
21
tc
10
tc
BHE, CSxE
WRL, WRH,
A23-A16
10
tc
Low Address
MTTC
Data OUT
MCTC
2) 3)
1)
tc
21
tc
10
tc
Low Address
tc
10
17
tc
17
tc
10
tc
10
12
tc tc
13
Data OUT
tc
18
tc
18
tc tc
19
tc
Valid
tc
Extended ALE
CSxL
10
tc
Normal ALE
CLKOUT
Normal ALE Cycle
Extended ALE Cycle
tc
11
tc
tc
11
10
tc
10
tc
11
17
C167CR
C167SR
Electrical Parameters
Data Sheet 78 V3.3, 2005-02
Figure 19 Multiplexed Bus, Read Access
12
11
11
Low Address
Extended ALE Cycle
(Extended ALE)
AD15-AD0
(Normal ALE)
AD15-AD0
RdCS
RD,
A23-A16
BHE, CSxE
Low Address
tc
21
10
tc
10
tc
tc
tc
21
10
tc
tc
10
Extended ALE
CSxL
Normal ALE
CLKOUT
tc
10
tc
11
tc
10
tc
tc
tc
10
MCTC
2) MTTC
3)
Data IN
tc
tc
Valid
1)
20
20
17
tc
tc
17
tc
tc
13
tc
tc
Data IN
14
15
tc
14
15
13
tc
MCT04419
tc
17
Normal ALE Cycle
C167CR
C167SR
Electrical Parameters
Data Sheet 79 V3.3, 2005-02
Bus Cycle Control via READY Input
The duration of an external bus cycle can be controlled by the external circuitry via the
READY input signal.
Synchronous READY permits the shortest possible bus cycle but requires the input
signal to be synchronous to the reference signal CLKOUT.
Asynchronous READY puts no timing constraints on the input signal but incurs one
waitstate minimum due to the additional synchronization stage.
Notes (Valid also for Figure 20)
4. Cycle as programmed, including MCTC waitstates (Example shows 0 MCTC WS).
5. READY sampled HIGH at this sampling point generates a READY controlled
waitstate, READY sampled LOW at this sampling point terminates the currently
running bus cycle.
6. These timings are given for test purposes only, in order to assure recognition at a
specific clock edge. If the Asynchronous READY signal does not fulfill the indicated
setup and hold times with respect to CLKOUT, it must fulfill tc27 in order to be safely
synchronized. Proper deactivation of READY is guaranteed if READY is deactivated
in response to the trailing (rising) edge of the corresponding command (RD or WR).
7. Multiplexed bus modes have a MUX waitstate added after a bus cycle, and an
additional MTTC waitstate may be inserted here. For a multiplexed bus with MTTC
waitstate this delay is 2 CLKOUT cycles, for a demultiplexed bus without MTTC
waitstate this delay is zero.
8. If the next following bus cycle is READY controlled, an active READY signal must be
disabled before the first valid sample point for the next bus cycle. This sample point
depends on the MTTC waitstate of the current cycle, and on the MCTC waitstates
and the ALE mode of the next following cycle. If the current cycle uses a multiplexed
bus the intrinsic MUX waitstate adds another CLKOUT cycle to the READY
deactivation time.
Table 20 READY Timing (Operating Conditions apply)
Parameter Symbol Limits Unit
Min. Max.
Input setup time to CLKOUT rising edge
Valid for: READY input
tc25 CC 12 ns
Input hold time after CLKOUT rising edge
Valid for: READY input
tc26 CC0–ns
Asynchronous READY input low time6) tc27 CC tc5 + tc25 –ns
C167CR
C167SR
Electrical Parameters
Data Sheet 80 V3.3, 2005-02
Figure 20 READY Timings
MCT04420
CLKOUT
D15-D0 Data IN
15
14
tc
tc
Running Cycle
4)
READY WS MUX/MTTC
D15-D0 Data OUT
20
tc
tc
18
tc
10
tc
21
(RD, WR)
Command 1)
12
tc
13
tc
tc
13
19
tc
/
6)
Synchronous
READY
tc
25
26
tc
5) 5)
25
tc
26
tc
26
tc
Asynchronous
READY
25
tc
5)
tc
5)
25
tc
26
8)
27
tc
The next external bus cycle may start here.
7)
C167CR
C167SR
Electrical Parameters
Data Sheet 81 V3.3, 2005-02
External Bus Arbitration
Table 21 Bus Arbitration Timing (Operating Conditions apply)
Parameter Symbol Limits Unit
Min. Max.
HOLD input setup time to CLKOUT falling edge tc28 SR 18 ns
CLKOUT to BREQ delay tc29 CC -4 6 ns
CLKOUT to HLDA delay tc30 CC -4 6 ns
CSx release1)
1) Not subject to production test - verified by design/characterization.
tc31 CC 0 10 ns
CSx drive tc32 CC -2 6 ns
Other signals release1) tc33 CC 0 10 ns
Other signals drive1) tc34 CC06ns
C167CR
C167SR
Electrical Parameters
Data Sheet 82 V3.3, 2005-02
Figure 21 External Bus Arbitration, Releasing the Bus
Notes
1. The C167CR will complete the currently running bus cycle before granting bus
access.
2. This is the first possibility for BREQ to get active.
3. The CS outputs will be resistive high (pull-up) after t33. Latched CS outputs are driven
high for 1 TCL before the output drivers are switched off.
tc
MCT04421
CS
Signals
Other
33
tc
3)
31
HOLD
HLDA
BREQ
CLKOUT
28
tc
1)
30
tc
29
tc
2)
C167CR
C167SR
Electrical Parameters
Data Sheet 83 V3.3, 2005-02
Figure 22 External Bus Arbitration, Regaining the Bus
Notes
4. This is the last chance for BREQ to trigger the indicated regain-sequence. Even if
BREQ is activated earlier, the regain-sequence is initiated by HOLD going high.
Please note that HOLD may also be deactivated without the C167CR requesting the
bus.
5. The next C167CR driven bus cycle may start here.
tc
MCT04422
CS
Signals
Other
34
tc
32
HOLD
HLDA
BREQ
CLKOUT
28
tc
30
tc
29
tc
4)
tc
29
tc
29
5)
C167CR
C167SR
Electrical Parameters
Data Sheet 84 V3.3, 2005-02
External XRAM Access
If XPER-Share mode is enabled the on-chip XRAM of the C167CR can be accessed
(during hold states) by an external master like an asynchronous SRAM.
Figure 23 External Access to the XRAM
Table 22 XRAM Access Timing (Operating Conditions apply)1)
1) The minimum access cycle time is 60 ns.
Parameter Symbol Limits Unit
Min. Max.
Address setup time before RD/WR falling edge t40 SR 4 ns
Address hold time after RD/WR rising edge t41 SR 0 ns
Data turn on delay after RD falling edge
Read
t42 CC 1 ns
Data output valid delay after address latched t43 CC 40 ns
Data turn off delay after RD rising edge t44 CC 1 14 ns
Write data setup time before WR rising edge
Write
t45 SR 10 ns
Write data hold time after WR rising edge t46 SR 2 ns
WR pulse width t47 SR 20 ns
WR signal recovery time t48 SR t40 –ns
Read Data
43
t
42
t
44
t
MCT04423
(RD, WR)
Write Data
Command
Address
40
t
45
t
47
t
46
t
48
t
41
t
C167CR
C167SR
Package Outlines
Data Sheet 85 V3.3, 2005-02
5 Package Outlines
Figure 24 P-MQFP-144-8 (Plastic Metric Quad Flat Package)
Does not include plastic or metal protrusion of 0.25 max. per side
4x
Index Marking
1 x 45˚
144
A
1
B
35 x 0.65 = 22.75
0.3 ±0.08
0.65
A-B
144x
28
31.2
1)
0.12
M
D
D C C
A-B
A-B
0.2
0.2
D
D
0.1
0.25 MIN.
2.75 MAX.
2.4 -0.1
0.88
4xH
±0.15
H
0.15 +0.08
-0.02
MAX.
1)
281)
31.2
GPM05248
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.Dimensions in mm
C167CR
C167SR
Package Outlines
Data Sheet 86 V3.3, 2005-02
Figure 25 P-BGA-176-2 (Plastic Ball Grid Array Package)
(0.8)
±0.1
0.4
(0.56)
±0.5
1.5
±0.2
15
4x
13
±1
-0.16
+0.14
ø0.5
13 x 1 = 13
A14
1
13 x 1 = 13
2 MAX.
Index Marking
0.2
(sharp edge)
Index Marking
±0.2
15
B
13
±1
176x
ø0.1
ø0.3
M
A
C
A
C
BC
A1
P1
1
M
GPA09430
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.Dimensions in mm
www.infineon.com
Published by Infineon Technologies AG