NIPPON CHEMI-CON CORPORATION
1270
Specifi cations in this bulletin are subject to change without notice.
1
Engineering Bulletin
Snap-ins, 105C
Aluminum Electrolytic Capacitor
No.584C / Jan.2005
@Endurance with ripple current : 105C 2,000 hours
@Non solvent-proof type
@Pb-free design
?SPECIFICATIONS
(at 20C, 120Hz)
(at 20C after 5 minutes)
(at 20C, 120Hz)
(at 120Hz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Items
-
40 to +105C (6.3 to 100Vdc) -25 to 105C (160 to 450Vdc)
6.3 to 450Vdc
P20% (M)
I=0.02CV or 3mA, whichever is smaller
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
Rated voltage (Vdc)
tanE (Max.)
Rated voltage (Vdc)
Z(
-
25C)/Z(+20C)
Z(
-
40C)/Z(+20C)
* : 0.15 for FD=35mm or L=20mm
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for 2,000 hours at 105C.
Capacitance change [P20% of the initial value
D.F. (tanE)[200% of the initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 105C
without voltage applied.
Capacitance change [P20% of the initial value
D.F. (tanE)[150% of the initial specified value
Leakage current [The initial specified value
Characteristics
6.3V
0.60 10V
0.50 16V
0.40 25V
0.30 35V
0.25 50V
0.20 63V
0.15 80V
0.15 100V
0.15
6.3V
4
15
10V
4
15
16V
4
15
25V
3
10
35V
3
8
50V
2
6
63V
2
6
80V
2
5
100V
2
5
160 to 250V
0.10 * 315 to 400V
0.15 450V
0.15
160 to 250V
4
-
315 to 400V
4
-
450V
8
-
?PART NUMBERING SYSTEM
?DIMENSIONS [mm]
Sleeve (Brown : PET)
Vent 4.5P1
LP2
FD+1max.
Negative mark PC board pin-out
2
-
1.2B6
5P0.5
14.2P1
4.2P0.5
@Terminal Code : LI (F35)
@Terminal Code : VS (F22 to F35) : Standard
*
4.0P0.5
F
D+1max.
Vent
Sleeve (Brown : PET)
LP2
Negative mark PC board pin-out
10
2
-
F2
*FD=35mm : 3.5P0.5mm
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 820MF:821, 3,300MF:332)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 6.3V:6R3, 10V:100, 315V:3B1)
Series code
Category
E KMH A A A V S N A A A A A A SM
13426789105121311 16 17 181514
No plastic disk is the standard design