MT8888C Integrated DTMF Transceiver with Intel Micro Interface Data Sheet Features September 2005 * Central office quality DTMF transmitter/receiver * Low power consumption * High speed Intel micro interface * Adjustable guard time * Automatic tone burst mode * Call progress tone detection to -30 dBm Ordering Information MT8888CE 20 Pin PDIP MT8888CS 20 Pin SOIC MT8888CN 24 Pin SSOP MT8888CP 28 Pin PLCC MT8888CE1 20 Pin PDIP* MT8888CS1 20 Pin SOIC* MT8888CN1 24 Pin SSOP* MT8888CP1 28 Pin PLCC* MT8888CPR 28 Pin PLCC MT8888CSR 20 Pin SOIC MT8888CSR1 20 Pin SOIC* MT8888CPR1 28 Pin PLCC* *Pb Free Matte Tin Applications * Credit card systems * Paging systems * Repeater systems/mobile radio * Interconnect dialers * Personal computers The receiver section is based upon the industry standard MT8870 DTMF receiver while the transmitter utilizes a switched capacitor D/A converter for low distortion, high accuracy DTMF signalling. Internal counters provide a burst mode such that tone bursts can be transmitted with precise timing. A call progress filter can be selected allowing a microprocessor to analyze call progress tones. The MT8888C is a monolithic DTMF transceiver with call progress filter. It is fabricated in CMOS technology offering low power consumption and high reliability. Tone Burst Gating Cct. IN+ + IN- - Dial Tone Filter High Group Filter OSC2 Low Group Filter Oscillator Circuit Control Logic Bias Circuit VDD VRef VSS Transmit Data Register Status Register Control Logic GS OSC1 The MT8888C utilizes an Intel micro interface, which allows the device to be connected to a number of popular microcontrollers with minimal external logic. Row and Column Counters D/A Converters Reel Reel Reel Reel -40C to +85C Description TONE Tubes Tubes Tubes Tubes Tubes Tubes Tubes Tubes Tape & Tape & Tape & Tape & Data Bus Buffer D0 D1 D2 D3 Interrupt Logic IRQ/CP Digital Algorithm and Code Converter Steering Logic ESt Control Register A Control Register B RD I/O Control Receive Data Register St/GT Figure 1 - Functional Block Diagram 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003-2005, Zarlink Semiconductor Inc. All Rights Reserved. CS WR RS0 MT8888C 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 VDD St/GT ESt D3 D2 D1 D0 NC NC IRQ/CP RD RS0 24 PIN SSOP 20 PIN PLASTIC DIP/SOIC GS NC ININ+ VDD St/GT EST IN+ INGS VRef VSS OSC1 OSC2 NC NC TONE WR CS 4 3 2 1 28 27 26 VDD St/GT ESt D3 D2 D1 D0 IRQ/CP RD RS0 NC VRef VSS OSC1 OSC2 NC NC 5 6 7 8 9 10 11 * 12 13 14 15 16 17 18 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 25 24 23 22 21 20 19 NC NC NC D3 D2 D1 D0 TONE WR CS RSO NC RD IRQ/CP IN+ INGS VRef VSS OSC1 OSC2 TONE WR CS Data Sheet 28 PIN PLCC Figure 2 - Pin Connections Pin Description Pin # 20 24 28 Name 1 1 1 IN+ Non-inverting op-amp input. 2 2 2 IN- Inverting op-amp input. 3 3 4 GS Gain Select. Gives access to output of front end differential amplifier for connection of feedback resistor. 4 4 6 VRef Reference Voltage output (VDD/2). 5 5 7 VSS Ground (0V ). 6 6 8 OSC1 DTMF clock/oscillator input. Connect a 4.7 M resistor to VSS if crystal oscillator is used. 7 7 9 OSC2 Oscillator output. A 3.579545 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit. Leave open circuit when OSC1 is driven externally. 8 10 12 TONE Output from internal DTMF transmitter. 9 11 13 WR Write microprocessor input. TTL compatible. 10 12 14 CS Chip Select input. Active Low. This signal must be qualified externally by address latch enable (ALE) signal, see Figure 14. 11 13 15 RS0 Register Select input. Refer to Table 3 for bit interpretation. TTL compatible. 12 14 17 RD Read microprocessor input. TTL compatible. 13 15 18 14-17 18-21 19-22 Description IRQ/CP Interrupt Request/Call Progress (open drain) output. In interrupt mode, this output goes low when a valid DTMF tone burst has been transmitted or received. In call progress mode, this pin will output a rectangular signal representative of the input signal applied at the input op-amp. The input signal must be within the bandwidth limits of the call progress filter, see Figure 8. D0-D3 Microprocessor Data Bus. High impedance when CS = 1 or RD = 1. TTL compatible. 2 Zarlink Semiconductor Inc. MT8888C Data Sheet Pin Description (continued) Pin # 20 24 28 Name 18 22 26 ESt 19 23 27 St/GT 20 24 28 VDD Positive power supply (5 V typical). NC No Connection. 8, 9, 3,5,10, 16,17 11,16, 23,25 1.0 Description Early Steering output. Presents a logic high once the digital algorithm has detected a valid tone pair (signal condition). Any momentary loss of signal condition will cause ESt to return to a logic low. Steering Input/Guard Time output (bidirectional). A voltage greater than VTSt detected at St causes the device to register the detected tone pair and update the output latch. A voltage less than VTSt frees the device to accept a new tone pair. The GT output acts to reset the external steering time-constant; its state is a function of ESt and the voltage on St. Functional Description The MT8888C Integrated DTMF Transceiver consists of a high performance DTMF receiver with an internal gain setting amplifier and a DTMF generator which employs a burst counter to synthesize precise tone bursts and pauses. A call progress mode can be selected so that frequencies within the specified passband can be detected. The Intel micro interface allows microcontrollers, such as the 8080, 80C31/51 and 8085, to access the MT8888C internal registers. 2.0 Input Configuration The input arrangement of the MT8888C provides a differential-input operational amplifier as well as a bias source (VRef), which is used to bias the inputs at VDD/2. Provision is made for connection of a feedback resistor to the opamp output (GS) for gain adjustment. In a single-ended configuration, the input pins are connected as shown in Figure 3. Figure 4 shows the necessary connections for a differential input configuration. 3.0 Receiver Section Separation of the low and high group tones is achieved by applying the DTMF signal to the inputs of two sixth-order switched capacitor bandpass filters, the bandwidths of which correspond to the low and high group frequencies (see Table 1). These filters incorporate notches at 350 Hz and 440 Hz for exceptional dial tone rejection. Each filter output is followed by a single order switched capacitor filter section, which smooths the signals prior to limiting. Limiting is performed by high-gain comparators which are provided with hysteresis to prevent detection of unwanted low-level signals. The outputs of the comparators provide full rail logic swings at the frequencies of the incoming DTMF signals. 3 Zarlink Semiconductor Inc. MT8888C Data Sheet IN+ IN- RIN C RF GS VRef MT8888C VOLTAGE GAIN (AV) = RF / RIN Figure 3 - Single-Ended Input Configuration C1 R1 IN+ INC2 R4 R5 GS R2 R3 VRef MT8888C DIFFERENTIAL INPUT AMPLIFIER C1 = C2 = 10 nF R1 = R4 = R5 = 100 k R2 = 60k, R3 = 37.5 k R3 = (R2R5)/(R2 + R5) VOLTAGE GAIN (AV diff) - R5/R1 INPUT IMPEDANCE (ZINdiff) = 2 R12 + (1/C)2 Figure 4 - Differential Input Configuration 4 Zarlink Semiconductor Inc. MT8888C Data Sheet FLOW FHIGH DIGIT D3 D2 D1 D0 697 1209 1 0 0 0 1 697 1336 2 0 0 1 0 697 1477 3 0 0 1 1 770 1209 4 0 1 0 0 770 1336 5 0 1 0 1 770 1477 6 0 1 1 0 852 1209 7 0 1 1 1 852 1336 8 1 0 0 0 852 1477 9 1 0 0 1 941 1336 0 1 0 1 0 941 1209 * 1 0 1 1 941 1477 # 1 1 0 0 697 1633 A 1 1 0 1 770 1633 B 1 1 1 0 852 1633 C 1 1 1 1 941 1633 D 0 0 0 0 Table 1 - Functional Encode/Decode Table Note: 0= LOGIC LOW, 1= LOGIC HIGH Following the filter section is a decoder employing digital counting techniques to determine the frequencies of the incoming tones and to verify that they correspond to standard DTMF frequencies. A complex averaging algorithm protects against tone simulation by extraneous signals such as voice while providing tolerance to small frequency deviations and variations. This averaging algorithm has been developed to ensure an optimum combination of immunity to talk-off and tolerance to the presence of interfering frequencies (third tones) and noise. When the detector recognizes the presence of two valid tones (this is referred to as the "signal condition" in some industry specifications) the "Early Steering" (ESt) output will go to an active state. Any subsequent loss of signal condition will cause ESt to assume an inactive state. 4.0 Steering Circuit Before registration of a decoded tone pair, the receiver checks for a valid signal duration (referred to as character recognition condition). This check is performed by an external RC time constant driven by ESt. A logic high on ESt causes vc (see Figure 5) to rise as the capacitor discharges. Provided that the signal condition is maintained (ESt remains high) for the validation period (tGTP), vc reaches the threshold (VTSt) of the steering logic to register the tone pair, latching its corresponding 4-bit code (see Table 1) into the Receive Data Register. At this point the GT output is activated and drives vc to VDD. GT continues to drive high as long as ESt remains high. Finally, after a short delay to allow the output latch to settle, the delayed steering output flag goes high, signalling that a received tone pair has been registered. The status of the delayed steering flag can be monitored by checking the appropriate bit in the status register. If Interrupt mode has been selected, the IRQ/CP pin will pull low when the delayed steering flag is active. The contents of the output latch are updated on an active delayed steering transition. This data is presented to the four bit bidirectional data bus when the Receive Data Register is read. The steering circuit works in reverse to validate the interdigit pause between signals. Thus, as well as rejecting signals too short to be considered valid, the 5 Zarlink Semiconductor Inc. MT8888C Data Sheet receiver will tolerate signal interruptions (drop out) too short to be considered a valid pause. This facility, together with the capability of selecting the steering time constants externally, allows the designer to tailor performance to meet a wide variety of system requirements. VDD MT8888C C1 VDD Vc St/GT ESt R1 tGTA = (R1C1) In (VDD / VTSt) tGTP = (R1C1) In [VDD / (VDD-VTSt)] Figure 5 - Basic Steering Circuit 5.0 Guard Time Adjustment The simple steering circuit shown in Figure 5 is adequate for most applications. Component values are chosen according to the following inequalities (see Figure 7): tREC tDPmax+tGTPmax - tDAmin tREC tDPmin+tGTPmin - tDAmax tID tDAmax+tGTAmax - tDPmin tDO tDAmin+tGTAmin - tDPmax 6 Zarlink Semiconductor Inc. MT8888C Data Sheet tGTP = (RPC1) In [VDD / (VDD-VTSt)] tGTA = (R1C1) In (VDD/VTSt) RP = (R1R2) / (R1 + R2) VDD C1 St/GT R1 ESt R2 a) decreasing tGTP; (tGTP < tGTA) tGTP = (R1C1) In [VDD / (VDD-VTSt)] tGTA = (RpC1) In (VDD/VTSt) RP = (R1R2) / (R1 + R2) VDD C1 St/GT R1 R2 ESt b) decreasing tGTA; (tGTP > tGTA) Figure 6 - Guard Time Adjustment The value of tDP is a device parameter (see AC Electrical Characteristics) and tREC is the minimum signal duration to be recognized by the receiver. A value for C1 of 0.1 F is recommended for most applications, leaving R1 to be selected by the designer. Different steering arrangements may be used to select independent tone present (tGTP) and tone absent (tGTA) guard times. This may be necessary to meet system specifications which place both accept and reject limits on tone duration and interdigital pause. Guard time adjustment also allows the designer to tailor system parameters such as talk off and noise immunity. Increasing tREC improves talk-off performance since it reduces the probability that tones simulated by speech will maintain a valid signal condition long enough to be registered. Alternatively, a relatively short tREC with a long tDO would be appropriate for extremely noisy environments where fast acquisition time and immunity to tone drop-outs are required. Design information for guard time adjustment is shown in Figure 6. The receiver timing is shown in Figure 7 with a description of the events in Figure 9. 6.0 Call Progress Filter A call progress mode, using the MT8888C, can be selected allowing the detection of various tones, which identify the progress of a telephone call on the network. The call progress tone input and DTMF input are common, however, call progress tones can only be detected when CP mode has been selected. DTMF signals cannot be detected if CP mode has been selected (see Table 7). Figure 8 indicates the useful detect bandwidth of the call progress filter. Frequencies presented to the input, which are within the `accept' bandwidth limits of the filter, are hard-limited by a high gain comparator with the IRQ/CP pin serving as the output. The squarewave output obtained from the schmitt trigger can be analyzed by a microprocessor or counter arrangement to determine the nature of the call progress tone being detected. Frequencies which are in the `reject' area will not be detected and consequently the IRQ/CP pin will remain low. 7 Zarlink Semiconductor Inc. MT8888C EVENTS A Data Sheet B C tREC tREC D F tDO tID TONE #n + 1 TONE #n Vin E TONE #n + 1 tDA tDP ESt tGTP tGTA VTSt St/GT tPStRX RX0-RX3 DECODED TONE # (n-1) # (n + 1) #n tPStb3 b3 b2 Read Status Register IRQ/CP Figure 7 - Receiver Timing Diagram LEVEL (dBm) -25 0 250 = Reject 500 750 FREQUENCY (Hz) = May Accept = Accept Figure 8 - Call Progress Response 8 Zarlink Semiconductor Inc. MT8888C Data Sheet EXPLANATION OF EVENTS A) B) C) TONE BURSTS DETECTED, TONE DURATION INVALID, RX DATA REGISTER NOT UPDATED. TONE #n DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN RX DATA REGISTER. END OF TONE #n DETECTED, TONE ABSENT DURATION VALID, INFORMATION IN RX DATA REGISTER RETAINED UNTIL NEXT VALID TONE PAIR. TONE #n+1 DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN RX DATA REGISTER. ACCEPTABLE DROPOUT OF TONE #n+1, TONE ABSENT DURATION INVALID, DATA REMAINS UNCHANGED. END OF TONE #n+1 DETECTED, TONE ABSENT DURATION VALID, INFORMATION IN RX DATA REGISTER RETAINED UNTIL NEXT VALID TONE PAIR. D) E) F) EXPLANATION OF SYMBOLS Vin ESt St/GT RX 0 -RX3 b3 b2 IRQ/CP tREC tREC tID tDO tDP tDA tGTP tGTA DTMF COMPOSITE INPUT SIGNAL. EARLY STEERING OUTPUT. INDICATES DETECTION OF VALID TONE FREQUENCIES. STEERING INPUT/GUARD TIME OUTPUT. DRIVES EXTERNAL RC TIMING CIRCUIT. 4-BIT DECODED DATA IN RECEIVE DATA REGISTER DELAYED STEERING. INDICATES THAT VALID FREQUENCIES HAVE BEEN PRESENT/ABSENT FOR THE REQUIRED GUARD TIME THUS CONSTITUTING A VALID SIGNAL. ACTIVE LOW FOR THE DURATION OF A VALID DTMF SIGNAL. INDICATES THAT VALID DATA IS IN THE RECEIVE DATA REGISTER. THE BIT IS CLEARED AFTER THE STATUS REGISTER IS READ. INTERRUPT IS ACTIVE INDICATING THAT NEW DATA IS IN THE RX DATA REGISTER. THE INTERRUPT IS CLEARED AFTER THE STATUS REGISTER IS READ. MAXIMUM DTMF SIGNAL DURATION NOT DETECTED AS VALID. MINIMUM DTMF SIGNAL DURATION REQUIRED FOR VALID RECOGNITION. MINIMUM TIME BETWEEN VALID SEQUENTIAL DTMF SIGNALS. MAXIMUM ALLOWABLE DROPOUT DURING VALID DTMF SIGNAL. TIME TO DETECT VALID FREQUENCIES PRESENT. TIME TO DETECT VALID FREQUENCIES ABSENT. GUARD TIME, TONE PRESENT. GUARD TIME, TONE ABSENT. Figure 9 - Description of Timing Events 7.0 DTMF Generator The DTMF transmitter employed in the MT8888C is capable of generating all sixteen standard DTMF tone pairs with low distortion and high accuracy. All frequencies are derived from an external 3.579545 MHz crystal. The sinusoidal waveforms for the individual tones are digitally synthesized using row and column programmable dividers and switched capacitor D/A converters. The row and column tones are mixed and filtered providing a DTMF signal with low total harmonic distortion and high accuracy. To specify a DTMF signal, data conforming to the encoding format shown in Table 1 must be written to the transmit Data Register. Note that this is the same as the receiver output code. The individual tones which are generated (fLOW and fHIGH) are referred to as Low Group and High Group tones. As seen from the table, the low group frequencies are 697, 770, 852 and 94 Hz. The high group frequencies are 1209, 1336, 1477 and 1633 Hz. Typically, the high group to low group amplitude ratio (twist) is 2 dB to compensate for high group attenuation on long loops. The period of each tone consists of 32 equal time segments. The period of a tone is controlled by varying the length of these time segments. During write operations to the Transmit Data Register the 4 bit data on the bus is latched and converted to 2 of 8 coding for use by the programmable divider circuitry. This code is used to specify a time segment length, which will ultimately determine the frequency of the tone. When the divider reaches the appropriate count, as determined by the input code, a reset pulse is issued and the counter starts again. The number of time segments is fixed at 32, however, by varying the segment length as described above the frequency can also be varied. The divider output clocks another counter, which addresses the sinewave lookup ROM. 9 Zarlink Semiconductor Inc. MT8888C Data Sheet The lookup table contains codes which are used by the switched capacitor D/A converter to obtain discrete and highly accurate DC voltage levels. Two identical circuits are employed to produce row and column tones, which are then mixed using a low noise summing amplifier. The oscillator described needs no "start-up" time as in other DTMF generators since the crystal oscillator is running continuously thus providing a high degree of tone burst accuracy. A bandwidth limiting filter is incorporated and serves to attenuate distortion products above 8 kHz. It can be seen from Figure 8 that the distortion products are very low in amplitude. Scaling Information 10 dB/Div Start Frequency = 0 Hz Stop Frequency = 3400 Hz Marker Frequency = 697 Hz and 1209 Hz Figure 10 - Spectrum Plot 8.0 Burst Mode In certain telephony applications it is required that DTMF signals being generated are of a specific duration determined either by the particular application or by any one of the exchange transmitter specifications currently existing. Standard DTMF signal timing can be accomplished by making use of the Burst Mode. The transmitter is capable of issuing symmetric bursts/pauses of predetermined duration. This burst/pause duration is 51 ms1 ms, which is a standard interval for autodialer and central office applications. After the burst/pause has been issued, the appropriate bit is set in the Status Register indicating that the transmitter is ready for more data. The timing described above is available when DTMF mode has been selected. However, when CP mode (Call Progress mode) is selected, the burst/pause duration is doubled to 102 ms 2 ms. Note that when CP mode and Burst mode have been selected, DTMF tones may be transmitted only and not received. In applications where a non-standard burst/pause time is desirable, a software timing loop or external timer can be used to provide the timing pulses when the burst mode is disabled by enabling and disabling the transmitter. 10 Zarlink Semiconductor Inc. MT8888C 9.0 Data Sheet Single Tone Generation A single tone mode is available whereby individual tones from the low group or high group can be generated. This mode can be used for DTMF test equipment applications, acknowledgment tone generation and distortion measurements. Refer to Control Register B description for details. OUTPUT FREQUENCY (Hz) ACTIVE INPUT SPECIFIED ACTUAL L1 697 699.1 +0.30 L2 770 766.2 -0.49 L3 852 847.4 -0.54 L4 941 948.0 +0.74 H1 1209 1215.9 +0.57 H2 1336 1331.7 -0.32 H3 1477 1471.9 -0.35 H4 1633 1645.0 +0.73 %ERROR Table 2 - Actual Frequencies Versus Standard Requirements 10.0 Distortion Calculations The MT8888C is capable of producing precise tone bursts with minimal error in frequency (see Table 2). The internal summing amplifier is followed by a first-order lowpass switched capacitor filter to minimize harmonic components and intermodulation products. The total harmonic distortion for a single tone can be calculated using Equation 1, which is the ratio of the total power of all the extraneous frequencies to the power of the fundamental frequency expressed as a percentage. V22f + V23f + V24f + .... V2nf THD (%) = 100 Vfundamental Figure 11 - Equation 1. THD (%) For a Single Tone The Fourier components of the tone output correspond to V2f.... Vnf as measured on the output waveform. The total harmonic distortion for a dual tone can be calculated using Equation 2. VL and VH correspond to the low group amplitude and high group amplitude, respectively and V2IMD is the sum of all the intermodulation components. The internal switched-capacitor filter following the D/A converter keeps distortion products down to a very low level as shown in Figure 10. V22L + V23L + .... V2nL + V22H + V23H + .. V2nH + V2IMD THD (%) = 100 V2L + V2H Figure 12 - Equation 2. THD (%) For a Dual Tone 11 Zarlink Semiconductor Inc. MT8888C 11.0 Data Sheet DTMF Clock Circuit The internal clock circuit is completed with the addition of a standard television color burst crystal. The crystal specification is as follows: Frequency: 3.579545 MHz Frequency Tolerance: 0.1% Resonance Mode: Parallel Load Capacitance: 18pF Maximum Series Resistance: 150 ohms Maximum Drive Level: e.g. 2mW CTS Knights MP036S Toyocom TQC-203-A-9S A number of MT8888C devices can be connected as shown in Figure 13 such that only one crystal is required. Alternatively, the OSC1 inputs on all devices can be driven from a TTL buffer with the OSC2 outputs left unconnected. MT8888C MT8888C MT8888C OSC1 OSC2 OSC1 OSC2 OSC1 OSC2 3.579545 MHz Figure 13 - Common Crystal Connection 12.0 Microprocessor Interface The MT8888C incorporates an Intel microprocessor interface which is compatible with fast versions (16 MHz) of the 80C51. No wait cycles need to be inserted. Figure 19 and Figure 20 are the timing diagrams for the Intel 8031, 8051 and 8085 (5 MHz) microcontrollers. By NANDing the address latch enable (ALE) output with the high-byte address (P2) decode output, CS is generated. Figure 14 summarizes the connection of these Intel processors to the MT8888C transceiver. The microprocessor interface provides access to five internal registers. The read-only Receive Data Register contains the decoded output of the last valid DTMF digit received. Data entered into the write-only Transmit Data Register will determine which tone pair is to be generated (see Table 1 for coding details). Transceiver control is accomplished with two control registers (see Table 6 and Table 7), CRA and CRB, which have the same address. A write operation to CRB is executed by first setting the most significant bit (b3) in CRA. The following write operation to the same address will then be directed to CRB, and subsequent write cycles will be directed back to CRA. The read-only status register indicates the current transceiver state (see Table 8). A software reset must be included at the beginning of all programs to initialize the control registers upon power-up or power reset (see Figure 19). Refer to Tables 4-7 for bit descriptions of the two control registers. The multiplexed IRQ/CP pin can be programmed to generate an interrupt upon validation of DTMF signals or when the transmitter is ready for more data (burst mode only). Alternatively, this pin can be configured to provide a squarewave output of the call progress signal. The IRQ/CP pin is an open drain output and requires an external pull-up resistor (see Figure 15). 12 Zarlink Semiconductor Inc. MT8888C Data Sheet RS0 WR RD 0 0 1 Write to Transmit Data Register 0 1 0 Read from Receive Data Register 1 0 1 Write to Control Register 1 1 0 Read from Status Register Table 3 - Internal Register Functions b3 RSEL FUNCTION b2 b1 b0 IRQ CP/DTMF TOUT Table 4 - CRA Bit Positions b3 b2 b1 b0 C/R S/D TEST BURST ENABLE Table 5 - CRB Bit Positions BIT NAME DESCRIPTION b0 TOUT Tone Output Control. A logic high enables the tone output; a logic low turns the tone output off. This bit controls all transmit tone functions. b1 CP/DTMF Call Progress or DTMF Mode Select. A logic high enables the receive call progress mode; a logic low enables DTMF mode. In DTMF mode the device is capable of receiving and transmitting DTMF signals. In CP mode a rectangular wave representation of the received tone signal will be present on the IRQ/CP output pin if IRQ has been enabled (control register A, b2=1). In order to be detected, CP signals must be within the bandwidth specified in the AC Electrical Characteristics for Call Progress. Note: DTMF signals cannot be detected when CP mode is selected. b2 IRQ Interrupt Enable. A logic high enables the interrupt function; a logic low deactivates the interrupt function. When IRQ is enabled and DTMF mode is selected (control register A, b1=0), the IRQ/CP output pin will go low when either 1) a valid DTMF signal has been received for a valid guard time duration, or 2) the transmitter is ready for more data (burst mode only). b3 RSEL Register Select. A logic high selects control register B for the next write cycle to the control register address. After writing to control register B, the following control register write cycle will be directed to control register A. Table 6 - Control Register A Description 13 Zarlink Semiconductor Inc. MT8888C Data Sheet BIT NAME DESCRIPTION b0 BURST Burst Mode Select. A logic high deactivates burst mode; a logic low enables burst mode. When activated, the digital code representing a DTMF signal (see Table 1) can be written to the transmit register, which will result in a transmit DTMF tone burst and pause of equal durations (typically 51 msec). Following the pause, the status register will be updated (b1 Transmit Data Register Empty), and an interrupt will occur if the interrupt mode has been enabled. When CP mode (control register A, b1) is enabled the normal tone burst and pause durations are extended from a typical duration of 51 msec to 102 msec. When BURST is high (deactivated) the transmit tone burst duration is determined by the TOUT bit (control register A, b0). b1 TEST Test Mode Control. A logic high enables the test mode; a logic low deactivates the test mode. When TEST is enabled and DTMF mode is selected (control register A, b1=0), the signal present on the IRQ/CP pin will be analogous to the state of the DELAYED STEERING bit of the status register (see Figure 7, signal b3). b2 S/D Single or Dual Tone Generation. A logic high selects the single tone output; a logic low selects the dual tone (DTMF) output. The single tone generation function requires further selection of either the row or column tones (low or high group) through the C/R bit (control register B, b3). b3 C/R Column or Row Tone Select. A logic high selects a column tone output; a logic low selects a row tone output. This function is used in conjunction with the S/D bit (control register B, b2). Table 7 - Control Register B Description BIT NAME b0 IRQ STATUS FLAG SET STATUS FLAG CLEARED Interrupt has occurred. Bit one (b1) or bit two (b2) is set. Interrupt is inactive. Cleared after Status Register is read. b1 TRANSMIT DATA REGISTER EMPTY (BURST MODE ONLY) Pause duration has terminated and transmitter is ready for new data. Cleared after Status Register is read or when in non-burst mode. b2 RECEIVE DATA REGISTER FULL Valid data is in the Receive Data Register. Cleared after Status Register is read. b3 DELAYED STEERING Set upon the valid detection of the absence of a DTMF signal. Cleared upon the detection of a valid DTMF signal. Table 8 - Status Register Description 14 Zarlink Semiconductor Inc. MT8888C Data Sheet 8031/8051 8080/8085 MT8888C A8-A15 CS A8 RS0 D0-D3 PO RD WR RD WR Figure 14 - MT8888C Interface Connections for Various Intel Micros VDD MT8880C C1 R1 DTMF/CP INPUT R2 VDD IN- St/GT GS ESt DTMF OUTPUT Notes: R1, R2 = 100 k 1% R3 = 374 k 1% R4 = 3.3 k 10% R5 = 4.7 M 10% RL = 10 k (min.) C1 = 100 nF 5% C2 = 100 nF 5% C3 = 100 nF 10%* C4 = 10 nF 10% X-tal = 3.579545 MHz C4 RL C2 R4 VRef D3 VSS D2 OSC1 D1 OSC2 D0 TONE IRQ/CP R5 X-tal C3 IN+ WR RD CS RS0 R3 To P or C * Microprocessor based systems can inject undesirable noise into the supply rails. The performance of the MT8888C can be optimized by keeping noise on the supply rails to a minimum. The decoupling capacitor (C3) should be connected close to the device and ground loops should be avoided. Figure 15 - Application Circuit (Single-Ended Input) 15 Zarlink Semiconductor Inc. MT8888C Data Sheet 5.0 VDC 5.0 VDC MMD6150 (or equivalent) 2.4 k 130 pF 3 k TEST POINT TEST POINT 24 k 100 pF MMD7000 (or equivalent) Test load for IRQ/CP pin Test load for D0-D3 pins Figure 16 - Test Circuits INITIALIZATION PROCEDURE A software reset must be included at the beginning of all programs to initialize the control registers after power up.The initialization procedure should be implemented 100ms after power up. Description: 1) 2) 3) 4) 5) 6) Read Status Register Write to Control Register Write to Control Register Write to Control Register Write to Control Register Read Status Register RS0 1 1 1 1 1 1 Control WR 1 0 0 0 0 1 RD 0 1 1 1 1 0 b3 X 0 0 1 0 X TYPICAL CONTROL SEQUENCE FOR BURST MODE APPLICATIONS Transmit DTMF tones of 50 ms burst/50 ms pause and Receive DTMF Tones. Sequence: RS0 WR RD b3 1) Write to Control Register A 1 0 1 1 (tone out, DTMF, IRQ, Select Control Register B) 2) Write to Control Register B 1 0 1 0 (burst mode) 3) Write to Transmit Data Register 0 0 1 0 (send a digit 7) 4) Wait for an interrupt or poll Status Register 5) Read the Status Register 1 1 0 X -if bit 1 is set, the Tx is ready for the next tone, in which case... Write to Transmit Register 0 0 (send a digit 5) -if bit 2 is set, a DTMF tone has been received, in which case.... Read the Receive Data Register 0 1 Data b2 X 0 0 0 0 X b1 X 0 0 0 0 X b0 X 0 0 0 0 X b2 1 b1 0 b0 1 0 0 0 1 1 1 X X X 1 0 1 0 1 0 X X X X -if both bits are set... Read the Receive Data Register 0 1 0 X X X X Write to Transmit Data Register 0 0 1 0 1 0 1 NOTE: IN THE TX BURST MODE, STATUS REGISTER BIT 1 WILL NOT BE SET UNTIL 100 ms (2 ms) AFTER THE DATA IS WRITTEN TO THE TX DATA REGISTER. IN EXTENDED BURST MODE THIS TIME WILL BE DOUBLED TO 200 ms ( 4 ms). Figure 17 - Application Notes 16 Zarlink Semiconductor Inc. MT8888C Data Sheet Absolute Maximum Ratings* Parameter Symbol 1 Power supply voltage VDD-VSS 2 Voltage on any pin 3 Current at any pin (Except VDD and VSS) 4 Storage temperature TST 5 Package power dissipation PD Min. Max. 6 V VSS-0.3 VDD+0.3 V 10 mA +150 C 1000 mW VDD VI -65 Units * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated. Parameter Sym. Min. Typ. Max. Units 5.00 5.25 V +85 C 3.583124 MHz 1 Positive power supply VDD 4.75 2 Operating temperature TO -40 3 Crystal clock frequency fCLK 3.575965 3.579545 Test Conditions Typical figures are at 25 C and for design aid only: not guaranteed and not subject to production testing. DC Electrical Characteristics - - VSS=0 V. Sym. Min. Typ. Max. Units Operating supply voltage VDD 4.75 5.0 5.25 V Operating supply current IDD 7.0 11 mA Power consumption PC 57.8 mW Characteristics 1 2 3 4 5 6 S U P I N P U T S 7 8 9 10 O U T P U T S 11 12 13 14 15 16 D i g i t a l Data Bus High level input voltage (OSC1) VIHO Low level input voltage (OSC1) VILO Steering threshold voltage VTSt Low level output voltage (OSC2) VOLO High level output voltage (OSC2) VOHO 3.5 2.2 2.3 V Note 9* 1.5 V Note 9* 2.5 V VDD=5V 0.1 V No load Note 9* V No load Note 9* 4.9 Output leakage current (IRQ) IOZ VRef output voltage VRef VRef output resistance ROR Low level input voltage VIL High level input voltage VIH Input leakage current IIZ Source current IOH -1.4 Sink current IOL 2.0 2.4 Test Conditions 1 10 A VOH=2.4 V 2.5 2.6 V No load, VDD=5V 1.3 k 0.8 2.0 V V A VIN=VSS to VDD -6.6 mA VOH=2.4V 4.0 mA VOL=0.4V 10 17 Zarlink Semiconductor Inc. MT8888C Data Sheet DC Electrical Characteristics (continued) - - VSS=0 V. (continued) Characteristics 17 18 19 ESt and St/Gt IRQ/ CP Sym. Min. Typ. Max. Units Test Conditions Source current IOH -0.5 -3.0 mA VOH=4.6V Sink current IOL 2 4 mA VOL=0.4V Sink current IOL 4 16 mA VOL=0.4V Characteristics are over recommended operating conditions unless otherwise stated. Typical figures are at 25 C, VDD =5V and for design aid only: not guaranteed and not subject to production testing. * See "Notes" following AC Electrical Characteristics Tables. Electrical Characteristics Gain Setting Amplifier - Voltages are with respect to ground (VSS) unless otherwise stated, VSS= 0V. Characteristics Sym. Min. Typ. Max. Units Test Conditions 100 nA VSS VIN VDD 1 Input leakage current IIN 2 Input resistance RIN 3 Input offset voltage VOS 4 Power supply rejection PSRR 50 dB 5 Common mode rejection CMRR 40 dB 6 DC open loop voltage gain AVOL 40 dB CL = 20p 7 Unity gain bandwidth BW 1.0 MHz CL = 20p 8 Output voltage swing VO 0.5 VDD-0.5 V RL 100 k to VSS 9 Allowable capacitive load (GS) CL 100 pF PM>40 10 Allowable resistive load (GS) RL 50 k VO = 4Vpp 11 Common mode range VCM 1.0 V RL = 50k 10 M 25 mV VDD-1.0 1 kHz Figures are for design aid only: not guaranteed and not subject to production testing. Characteristics are over recommended operating conditions unless otherwise stated. MT8888C AC Electrical Characteristics Characteristics 1 R X Valid input signal levels (each tone of composite signal) - Voltages are with respect to ground (VSS) unless otherwise stated. Sym. Min. Typ. Max. Units Notes* -29 +1 dBm 1,2,3,5,6 27.5 869 mVRMS 1,2,3,5,6 Characteristics are over recommended operating conditions (unless otherwise stated) using the test circuit shown in Figure 15. 18 Zarlink Semiconductor Inc. MT8888C Data Sheet AC Electrical Characteristics - Voltages are with respect to ground (VSS) unless otherwise stated. fC=3.579545 MHz Characteristics Sym. Typ. Min. Max. Units Notes* 1 Positive twist accept 8 dB 2,3,6,9 2 Negative twist accept 8 dB 2,3,6,9 3 4 R X Freq. deviation accept 1.5% 2Hz 2,3,5 Freq. deviation reject 3.5% 2,3,5 5 Third tone tolerance -16 dB 2,3,4,5,9,10 6 Noise tolerance -12 dB 2,3,4,5,7,9,10 7 Dial tone tolerance 22 dB 2,3,4,5,8,9 Characteristics are over recommended operating conditions unless otherwise stated. Typical figures are at 25C, VDD = 5 V, and for design aid only: not guaranteed and not subject to production testing. * *See "Notes" following AC Electrical Characteristics Tables. AC Electrical Characteristics- Call Progress - Voltages are with respect to ground (VSS), unless otherwise stated. Characteristics Sym. Min. 310 Typ. Max. Units Conditions 500 Hz @ -25 dBm, Note 9 1 Accept Bandwidth fA 2 Lower freq. (REJECT) fLR 290 Hz @ -25 dBm 3 Upper freq. (REJECT) fHR 540 Hz @ -25 dBm 4 Call progress tone detect level (total power) -30 dBm Characteristics are over recommended operating conditions unless otherwise stated Typical figures are at 25C, VDD=5 V, and for design aid only: not guaranteed and not subject to production testing AC Electrical Characteristics - DTMF Reception - Typical DTMF tone accept and reject requirements. Actual values are user selectable as per Figures 5, 6 and 7. Characteristics Sym. Min. Typ. Max. Units 1 Minimum tone accept duration tREC 40 ms 2 Maximum tone reject duration tREC 20 ms 3 Minimum interdigit pause duration tID 40 ms 4 Maximum tone drop-out duration tDO 20 ms Characteristics are over recommended operating conditions unless otherwise stated Typical figures are at 25C, VDD=5 V, and for design aid only: not guaranteed and not subject to production testing 19 Zarlink Semiconductor Inc. Conditions MT8888C Data Sheet AC Electrical Characteristics - Voltages are with respect to ground (VSS), unless otherwise stated. Characteristics 1 Sym. Min. Typ. Max. Units Conditions T O N E Tone present detect time tDP 3 11 14 ms Note 11 Tone absent detect time tDA 0.5 4 8.5 ms Note 11 Delay St to b3 tPStb3 13 s See Figure 7 I N Delay St to RX0-RX3 tPStRX 8 s See Figure 7 5 Tone burst duration tBST 50 52 ms DTMF mode 6 Tone pause duration tPS 50 52 ms DTMF mode 7 Tone burst duration (extended) tBSTE 100 104 ms Call Progress mode Tone pause duration (extended) tPSE 100 104 ms Call Progress mode High group output level VHOUT -6.1 -2.1 dBm RL=10k Low group output level VLOUT -8.1 -4.1 dBm RL=10k Pre-emphasis dBP 0 3 dB RL=10k Output distortion (Single Tone) THD dB 25 kHz Bandwidth 2 3 4 8 9 10 11 12 T O N E O U T 2 -35 13 RL=10k 14 Frequency deviation 15 Output load resistance RLT Crystal/clock frequency fC 16 17 18 19 X T A L Clock input rise and fall time tCLRF Clock input duty cycle DCCL Capacitive load (OSC2) 0.7 fD 10 1.5 % 50 k 3.5759 3.5795 3.5831 40 50 CLO fC=3.579545 MHz MHz 110 ns Ext. clock 60 % Ext. clock 30 pF Timing is over recommended temperature & power supply voltages. Typical figures are at 25C and for design aid only: not guaranteed and not subject to production testing. AC Electrical Characteristics- MPU Interface - Voltages are with respect to ground (VSS), unless otherwise stated. Characteristics Sym. Min. Typ. Max. Units Conditions 1 RD/WR clock frequency fCYC 4.0 MHz Figure 18 2 RD/WR cycle period tCYC 250 ns Figure 18 3 RD/WR rise and fall time tR, tF ns Figure 18 4 Address setup time tAS 23 ns Figures 19 & 20 5 Address hold time tAH 26 ns Figures 19 & 20 6 Data hold time (read) tDHR 22 ns Figures 19 & 20 7 RD to valid data delay (read) tDDR ns Figures 19 & 20 8 RD, WR pulse width low tPWL ns Figures 18, 19 & 20 9 RD, WR pulse width high tPWH ns Figures 18, 19 & 20 10 Data setup time (write) tDSW 45 ns Figures 19 & 20 11 Data hold time (write) tDHW 10 ns Figures 19 & 20 12 Input Capacitance (data bus) 20 100 150 100 5 CIN 20 Zarlink Semiconductor Inc. pF MT8888C Data Sheet AC Electrical Characteristics- MPU Interface (continued)- Voltages are with respect to ground (VSS), unless otherwise Characteristics Sym. Min. Typ. Max. Units COUT 5 pF 13 Output Capacitance (IRQ/CP) Characteristics are over recommended operating conditions unless otherwise stated Typical figures are at 25C, VDD=5 V, and for design aid only: not guaranteed and not subject to production testing Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. dBm=decibels above or below a reference power of 1 mW into a 600 ohm load. Digit sequence consists of all 16 DTMF tones. Tone duration=40 ms. Tone pause=40 ms. Nominal DTMF frequencies are used. Both tones in the composite signal have an equal amplitude. The tone pair is deviated by 1.5%2 Hz. Bandwidth limited (3 kHz) Gaussian noise. The precise dial tone frequencies are 350 and 440 Hz (2%). Guaranteed by design and characterization. Not subject to production testing. Referenced to the lowest amplitude tone in the DTMF signal. For guard time calculation purposes. tCYC tR tF tPWH RD/WR tPWL Figure 18 - RD/WR Clock Pulse tPWL RD tPWH tAS tAH CS, RS0 tDHR tDDR DATA BUS Figure 19 - 8031/8051/8085 Read Timing Diagram tPWL WR tPWH tAS tAH CS, RS0 tDSW tDHW DATA BUS Figure 20 - 8031/8051/8085 Write Timing Diagram 21 Zarlink Semiconductor Inc. Conditions For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request. Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE