TCK22xxxG/TCK2065G/TCK1024G TOSHIBA CMOS Linear Integrated Circuit Silicon Monolithic TCK22xxxG, TCK2065G, TCK1024G Load Switch IC with Over current limited function The TCK22xxxG, TCK2065G and TCK1024G are Load Switch ICs for power management with Over Current Limited function featuring low switch on resistance, ultra low quiescent current, high output current and wide input voltage operation. Typical switch ON resistance is only 31 m at VIN = 5.0 V, IOUT = -0.15 A load conditions. And these feature a thermal shut down function and output auto-discharge function. These devices are available in 0.4 mm pitch ultra small package WCSP6E (0.8 mm x 1.2 mm, t: 0.55 mm). So these devices are ideal for portable applications that require high-density board assembly such as cellular phone. Feature WCSP6E Weight: 1 mg (typ.) Over current limit function ICL = 400/740/1110/1540 mA (Option) Thermal shutdown function Inrush current reduction Output auto-discharge function True reverse current blocking function(Option) Under voltage lockout function(Option) Low ON resistance : RON = 31 m (typ.) at VIN = 5.0 V, IOUT = -0.15 A RON = 40 m (typ.) at VIN = 3.3 V, IOUT = -0.15 A RON = 70 m (typ.) at VIN = 1.8 V, IOUT = -0.15 A Low quiescent current: IQ = 25 A (typ.) at VIN = 5.5 V, IOUT = 0 mA Pull down connection between CONTROL and GND Ultra small package : WCSP6E (0.8 mm x 1.2 mm, t: 0.55 mm) Start of commercial production 2016-02 (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 1 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Function Table Function Part number Device Marking Output current limit True Reverse current blocking Output autodischarge Under voltage lock out Thermal shut down Control pin polarity TCK22946G 400 mA Built in Built in Built in Built in Active High 1T TCK22951G 740 mA Built in Built in Built in Built in Active High 2T TCK2065G 1110 mA Built in Built in Built in Built in Active High 3T TCK1024G 1540 mA Built in Built in Built in Built in Active High 4T TCK22891G 400 mA N/A Built in N/A Built in Active High 5T TCK22892G 740 mA N/A Built in N/A Built in Active High 6T TCK22893G 1110 mA N/A Built in N/A Built in Active High 7T TCK22894G 1540 mA N/A Built in N/A Built in Active High 8T (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 2 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Absolute Maximum Ratings (Ta = 25C) Characteristics Symbol Rating Unit Input voltage VIN -0.3 to 6.0 V Control voltage VCT -0.3 to 6.0 V Output voltage VOUT -0.3 to 6.0 V Output current IOUT Internally limited - Power dissipation PD 800 Operating temperature range Topr -40 to 85 C Tj 150 C Tstg -55 to 150 C Junction temeperature Storage temperature (Note 1) mW Note : Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note1: Rating at mounting on a board Board material: Glass epoxy (FR4) Board dimension: 40mm x 40mm (both sides of board), t=1.6mm Metal pattern ratio: a surface approximately 50%, the reverse side approximately 50% Through hole: diameter 0.5mm x 28 Operating conditions Characteristics Symbol Input voltage VIN Output voltage Condition TCK22946G TCK22891G Others VIH CONTROL Low-level input voltage 2 1 B 1.1 5.5 1.4 5.5 VIN 1.2V < VIN 5.5 V 1.0 1.1V VIN 1.2 V 0.9 0.4 VIL Pin Assignment(Top view) A Max Unit V VOUT CONTROL High-level input voltage Min V V V Top marking Lot trace code C A1: VOUT B1: VOUT C1: GND A2: VIN B2: VIN C2: CONTROL Device Marking Index (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 3 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Block Diagram TCK22946G, TCK22951G, TCK2065G, TCK1024G True Reverse current blocking V IN Current Sense Q1 Thermal Shut down UVLO VOUT Over current Protection Slew Rate Control Driver CONTROL Control Logic Q2 Output Discharge Pull Down GND TCK22891G, TCK22892G, TCK22893G, TCK22894G Current Sense V IN Q1 Thermal Shut down VOUT Over current Protection Slew Rate Control Driver CONTROL Control Logic Q2 Output Discharge Pull Down GND Operation logic table TCK22946G, TCK22951G TCK2065G, TCK1024G Control "High" Control "Low" TCK22891G, TCK22892G TCK22893G, TCK22894G Output Q1 ON ON Discharge Q2 Reverse current blocking OFF Active OFF Output Q1 OFF OFF Discharge Q2 Reverse current blocking ON Active ON (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 4 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Electrical Characteristics DC Characteristics (Ta = -40 to 85C) Ta = -40 to 85C Ta = 25C Characteristics Quiescent current ( ON state) Quiescent current ( OFF state) Symbol IQ IQ(OFF) Reverse blocking current IRB Reverse blocking voltage threshold VRB Test Condition IOUT = 0 mA Unit Min Typ. Max Min Max VIN = 1.1 V 16 A VIN = 5.5 V 25 50 A 0.6 2.5 A 0.01 2 A 35 mV -15 mV VIN = 5.5 V, VOUT = OPEN, VOUT = 5.0 V, VIN = 0 V, RCB active (Note 2) VOUT - VIN (Note 2) VOUT - VIN Reverse blocking release voltage threshold VRBR Under Voltage Lock Out (UVLO) rising threshold VUVL_RI (Note 2) 0.82 1.1 V Under Voltage Lock Out (UVLO) falling threshold VUVL_FA (Note 2) 0.77 V VIN = 5.0 V 31 85 VIN = 3.3 V 40 95 VIN = 1.8 V 70 140 VIN = 1.2 V (Note 3) 141 VIN = 1.1 V (Note 3) 179 TCK22946G TCK22891G 400 TCK22951G TCK22892G 740 On resistance Output Limited Current Output discharge on resistance RON ICL RSD (Note 2) IOUT = -0.15 A VIN = 5.5 V m mA TCK2065G TCK22893G 1110 TCK1024G TCK22894G 1540 100 Note 2: Only applies to the TCK22946G, TCK22951G, TCK2065G and TCK1024G Note 3: Only applies to the TCK22946G and TCK22891G (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 5 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G AC Characteristics (Ta = 25C) VIN = 5.0 V Characteristics Symbol Test Condition(Figure 1) Min Typ. Max Unit VOUT rise time tr VIN= 5.0 V , RL = 500 , CL=0.1 F, 50 s VOUT fall time tf VIN= 5.0 V , RL = 500 , CL=0.1 F, 50 s Turn on delay tON VIN= 5.0 V , RL = 500 , CL=0.1 F, 40 s Turn off delay tOFF VIN= 5.0 V , RL = 500 , CL=0.1 F, 10 s AC Waveform VIH VCT tr VOUT 50% tf 90% 10% 50% VIL 90% 10% 90% VOUT 10% tON Figure 1 (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation tOFF VOH VOL tr, tf, tON, tOFF Waveforms 6 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Application Note Application circuit example (top view) 1. The figure below shows the recommended configuration. CONTROL GND VOUT LOAD VIN CIN COUT CL RL Control Voltage Output Voltage HIGH ON LOW OFF OPEN OFF 1) Input and Output capacitor An input capacitor (CIN) and an output capacitor (COUT) are necessary for the stable operation. And they are effective to reduce voltage overshoot or undershoot due to sharp changes in output current and also for improved stability of the power supply. When used, place CIN and COUT more than 1.0F as close to VIN pin to improve stability of the power supply. 2) Control pin The CONTROL pin controls state of the switch, operated by the control voltage and Schmitt trigger. Also, pull down resistance equivalent to a few M is connected between CONTROL and GND, thus the load switch IC is in OFF state even when CONTROL pin is OPEN. 2. Over current limit function This device has a built-in fold-back type of Current-limiting Circuit. is recommended for system design with enough margin. Around 15% or more derating against typical values 3. Thermal shutdown function Each device has a built-in Thermal shutdown circuit. If the junction temperature goes beyond 170C (Typ.), thermal shutdown circuit operates and turns off power switch. When the junction temperature decreases lower than 150C, the power switch is turned on due to hysteresis. This operation is repeated as long as the junction temperature continues increasing. 4. True reverse current blocking function(Option) Some of these devices have built-in True reverse current blocking circuit (TRCB) to block reverse current from VOUT to VIN regardless of output MOSFET ON/OFF condition. (Full-Time Reverse Current Protection) 5. Under-voltage Lockout function(Option) Some of these devices have a built-in Under-voltage Lockout Circuit to turn off switch if VIN drops below UVLO. circuit has hysteresis and UVLO is released when VIN exceeds threshold. This 6. Instructions and directions for use Each device has several built-in protection functions, but these does not assure for the suppression of uprising device operation. In use of these products, please read through and understand dissipation idea for absolute maximum ratings from the above mention or our `Semiconductor Reliability Handbook'. Then use these products under absolute maximum ratings in any condition. Furthermore, Toshiba recommend inserting failsafe system into the design. (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 7 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G 7. Power Dissipation Power dissipation is measured on the board condition shown below. [The Board Condition] Board material: Glass epoxy (FR4) Board dimension: 40mm x 40mm (both sides of board), t=1.6mm Metal pattern ratio: a surface approximately 50%, the reverse side approximately 50% Through hole: diameter 0.5mm x 28 PD - Ta Power Dissipation PD (mW) 1000 800 600 400 200 0 -40 0 40 80 Ambient Temperature Ta () 120 Please allow sufficient margin when designing a board pattern to fit the expected power dissipation. Also take into consideration the ambient temperature, input voltage, output current etc. and applying the appropriate derating for allowable power dissipation during operation. (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 8 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Package dimension Unit: mm Weight: 1 mg (typ.) (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 9 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G Land pattern dimensions (for reference only) Unit mm (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 10 2019-04-12 TCK22xxxG/TCK2065G/TCK1024G RESTRICTIONS ON PRODUCT USE Toshiba Corporation and its subsidiaries and affiliates are collectively referred to as "TOSHIBA". Hardware, software and systems described in this document are collectively referred to as "Product". TOSHIBA reserves the right to make changes to the information in this document and related Product without notice. This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, lifesaving and/or life supporting medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, and devices related to power plant. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative or contact us via our website. Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. https://toshiba.semicon-storage.com/ (c) 2018 - 2019 Toshiba Electronic Devices & Storage Corporation 11 2019-04-12