FT312D-32Q1C-T - FTDI - Datasheet.Live

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Future Technology Devices

International Ltd.

DS_FT312D

(USB Android Host IC)

The FT312D is a USB 2.0 Full Speed

host IC specifically targeted at

providing access to peripheral

hardware from an Android platform

with a USB device port. The device will

bridge the USB port to a UART

interface via the Android Open

Accessory protocol and has the

following advanced features:

 Single chip USB to UART interface.

 Entire USB protocol handled on the chip. No

USB specific firmware programming required.

 Supports USB bulk transfer mode

 Basic UART interface with RXD, TXD, RTS#,

CTS# pins.

 TX_ACTIVE signal for controlling transceivers

on RS485 interfaces.

 UART RX buffer size is 5512 bytes

 UART TX buffer size is 256 bytes

 USB_ERROR indicator pin

 Suitable for use on any Android platform

supporting Android Open Accessory Mode

(Typically 3.1 onwards, however some

platforms may port Open Accessory Mode to

version 2.3.4)

 12MHz oscillator using external crystal.

 Integrated power-on-reset circuit.

 +3V3Single Supply Operation with 5V tolerant

inputs.

 USB 2.0 Full Speed compatible.

 Extended operating temperature range; -40⁰C

to 85⁰C.

 Available in compact Pb-free 32 Pin LQFP and

QFN packages (both RoHS compliant).

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced

in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are

supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology

Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your

statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in

which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary

information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by

the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow

G41 1HH United Kingdom. Scotland Registered Company Number: SC136640

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

1 Typical Applications

 Connecting Android phones to USB accessories

 Connecting Android tablets to USB accessories

 Controlling instrumentation from Android

devices.

 Home automation via Android devices

 Data logging from USB accessories

 Connecting serial printing devices to Android

devices

1.1 Part Numbers

Part Number

Package

FT312D-32Q1C-x

32 Pin QFN

FT312D-32L1C-x

32 Pin LQFP

Note: Packing codes for x is:

- R: Taped and Reel, QFN 3,000pcs per reel, LQFP 1500 pcs per reel.

- (no suffix): Tray packing, 260pcs per tray QFN, 250 pcs per tray LQFP

For example: FT312D-32Q1C-R is 3,000pcs QFN taped and reel packing

1.2 USB Compliant

At the time of writing this datasheet, the FT312Dhad not completed the USB Compliancy Test.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

2 FT312D Block Diagram

USB

Transceiver USB Host Buffer UART

USBDP

USBDM

TXD

RXD

RTS#

CTS#

TX_ACTIVE

USB_ERROR#

Figure 2.1FT312D Block Diagram

For a description of the function please refer to Section 4.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Table of Contents

1 Typical Applications ...................................................................... 2

1.1 Part Numbers ..................................................................................... 2

1.2 USB Compliant .................................................................................... 2

2 FT312D Block Diagram ................................................................. 3

3 Device Pin Out and Signal Description .......................................... 6

3.1 Package Symbol.................................................................................. 6

3.1.1 Package PinOut Description ........................................................................................... 6

4 Function Description..................................................................... 8

4.1 Key Features ....................................................................................... 8

4.2 Functional Block Descriptions ............................................................. 8

4.2.1 UART Interface Module ................................................................................................. 8

4.2.2 Buffers ....................................................................................................................... 8

4.2.3 USB Host .................................................................................................................... 8

4.2.4 USB Transceivers ......................................................................................................... 8

4.3 Default Descriptor Strings .................................................................. 8

5 UART Interface ........................................................................... 10

6 USB Error Detection .................................................................... 12

7 Absolute Maximum Ratings ........................................................ 13

7.1 DC Characteristics .............................................................................14

7.2 ESD and Latch-up Specifications ........................................................15

8 Application Examples ................................................................. 16

8.1 USB to UARTConverter .......................................................................16

8.2 USB to RS232 Converter ....................................................................17

9 Package Parameters ................................................................... 18

9.1 FT312D Package Markings .................................................................18

9.1.1 QFN-32 .................................................................................................................... 18

9.1.2 LQFP-32 ................................................................................................................... 19

9.2 FT312DPackage Dimensions ..............................................................20

9.2.1 QFN-32 Package Dimensions ....................................................................................... 20

9.2.2 LQFP-32 Package Dimensions ...................................................................................... 21

9.3 Solder Reflow Profile .........................................................................22

10 Contact Information ................................................................... 24

Appendix A – References ............................................................................25

Appendix B - List of Figures and Tables ......................................................26

Appendix C - Revision History .....................................................................27

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

3 Device Pin Out and Signal Description

3.1 Package Symbol

17

18

19

20

21

22

23

24

USBDP

FT312D

QFN 32

USBDM

GND

NC

VCCIO

TXD

RXD

RTS#

25

26

27

28

29

30

31

32

CTS#

GND

VCCIO

TX_ACTIVE

NC

USB_ERROR#

GND

33

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

TEST1

VREGOUT

GND

XTOUT

XTIN

AVCC

VCC

GND

VCCIO

NC

TEST0

RESET#

TEST2

Figure 3.1QFN Schematic Symbol

NOTE: The pinout is the same for the QFN and LQFP packages.

NOTE: Pin 33 on the symbol is the copper pad in the centre of the QFN package

3.1.1 Package PinOut Description

Note: # denotes an active low signal.

Pin No.

Name

Type

Description

2

VCC

POWER

Input

3V3 supply to IC internal 1V8 regulator

3

AVCC

POWER

Input

1V8 supply to IC core

13, 22, 28

VCCIO

POWER

Input

3V3 supply for the IO cells

7

VREGOUT

POWER

Output

1V8 output. May be used as input source for pin 3.

1,6,14,15,16,19,27

GND

POWER

Input

0V Ground input.

Table 3.1 Power and Ground

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Pin No.

Name

Type

Description

4

XTIN

INPUT

Input to 12MHz Oscillator Cell. Connect 12MHz crystal

across pins 4 and 5.

5

XTOUT

OUTPUT

Output from 12MHz Oscillator Cell. Connect 12MHz

crystal across pins 4 and 5.

8

TEST1

INPUT

For internal use. Pull to GND

9

TEST2

INPUT

For factory use. Pull to 3V3.

10

RESET#

INPUT

Reset input (active low).

11

TEST0

OUTPUT

Leave unterminated.

12

NC

-

No connect pins. Leave unterminated.

17

USBDP

INPUT/OUTPUT

USB Data Signal Plus.

18

USBDM

INPUT/OUTPUT

USB Data Signal Minus.

20

NC

-

No connect pins. Leave unterminated.

21

NC

-

No connect pins. Leave unterminated.

23

TXD

OUTPUT

Transmit asynchronous data output

24

RXD

INPUT

Receive asynchronous data input

25

RTS#

OUTPUT

Request to send control output

26

CTS#

INPUT

Clear to send control input

29

TX_ACTIVE

OUTPUT

UART active signal (typically used with RS485)

30

NC

-

No connect pins. Leave un-terminated

31

NC

-

No connect pins. Leave un-terminated

32

USB_ERROR#

OUTPUT

Output signal to indicate a problem with the USB

connection

Table 3.2 Function pins

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

4 Function Description

The FT312D is FTDI’s second dedicated Android Open Accessory Mode integrated circuit device or Android

Host. The FT312D USB host port is dedicated to support of the Android Open Accessory class and will

bridge data between this port and the UART interface.

4.1 Key Features

Easy to use Android Open Accessory IC translating the Device port of the Android device into UART

capabilities

4.2 Functional Block Descriptions

The following paragraphs describe each function within FT312D. Please refer to the block diagram shown

inFigure 2.1.

4.2.1 UART Interface Module

The FT312DUART module controls the UART interface providing basic RXD, TXD signalling with

RTS#/CTS# hardware flow control. An additional TX_Active signal is supplied to control external RS485

transceivers for users wishing to create a USB to RS485 bridge. The UART supports baud rates from 300

baud to 921600 baud. A full description of the UART module is provided in Section 5.

4.2.2 Buffers

The FT312D provides internal buffering between the USB port and the UART port of the IC for smooth

data streaming.

The Android device can send NAK’s to the USB OUT token sent from the FT312D. This can happen when

the UART application on the Android is running in the background or multiple applications are launched in

the Android device. When the UART application on the Android device is not accepting data, the data will

be buffered in the UART RX buffer in FT312D. The UART RX buffer size is 5512 bytes.

The UART_TX buffer which stores data from the USB port, heading for the UART is 256 bytes.

4.2.3 USB Host

The USB Host block handles the parallel-to-serial and serial-to-parallel conversion of the USB physical

layer. This includes bit stuffing, CRC generation.

4.2.4 USB Transceivers

USB transceiver cells provide the physical USB device interface supporting USB 1.1 and USB 2.0

standards. Low-speed and full-speed USB data rates are supported. The output driver provides 3V3 level

slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB

DATA IN, SE0 and USB Reset condition detection. These cells also include integrated internal pull-down

resistors as required for host mode.

4.3 Default Descriptor Strings

When the USB port is connected to the Android USB port, the Android platform will determine which

application to load based on the strings read from the FT312D. These strings are configurable with a

Windows utility: FT312D_Cofiguration available for download from the FTDI website.

http://www.ftdichip.com

Please refer to the application note AN_236 User Guide for FT312D Configuration to change the default

string values.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Default values for the strings are set in the device as per Table 4.1

Descriptor String

Default Value

Manufacturer

FTDI

Model

Android Accessory FT312D

Version

1.0

Serial

FTDI FT312D

URL

http://www.ftdichip.com/Android.htm

Description

FTDI Android Accessory FT312D

Table 4.1Default Descriptor Strings

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

5 UART Interface

The interface implements a standard asynchronous serial UART port with flow control, for example

RS232/422/485. The UART can support baud rates from 300 to 921600 with RTS/CTS flow control. The

UART can support baud rates from 300 to 115200 with no flow control.

Data transfer uses NRZ (Non-Return to Zero) data format consisting of 1 start bit, 7 or 8 data bits, an

optional parity bit, and one or two stop bits. When transmitting the data bits, the least significant bit is

transmitted first. Transmit and receive waveforms are illustrated in Figure 5-1 and Figure 5-2:

Figure 5-1 UART Receive Waveform

Figure 5-2 UART Transmit Waveform

Baud rate (default =9600 baud), flow control settings (default = None), number of data bits (default=8),

parity (default is no parity) and number of stop bits (default=1) are all configurable from the Android

application. Please refer to ftdichip document number FT_000532 for further details.

http://www.ftdichip.com

TX_ACTIVE is transmit enable, this output may be used in RS485 designs to enable the line driver for

transmit mode.

UART RX buffer size is 5512 bytes and UART TX buffer size is 256 bytes.

Note: UART software flow control with XON/XOFF is not supported

UART hardware flow control with DTR/DSR is not supported

Note:

The FT312D has to enumerate the Android device before receiving data from the UART device.

This can be implemented by disconnecting the UART TXD signal of external UART device connected to the

FT312D RXD signal until after the FT312D has established the USB link with Android device.

The connection sequence should be:

1. Connect FT312D to Android and complete enumeration.

2. Connect the TXD of UART device to FT312D’s RXD then start to receive data.

There are two methods to implement this function:

1.When FT312D connects to the Android device and enumeration is completed, the USB_ERROR# will

become Logic 0 (default Logic 1). This signal can be used to control the TTL gate (74LVC2G241,

74LVC1G125 or others) ON/OFF such that the TXD/RXD lines are connected/disconnected.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Figure 5-3 UART RXD and TXD connection gated by Enumeration

2. If the UART device has an enable pin(active high enable) such as on the GPS module, the

USB_ERROR# can also be used. The USB_ERROR# pin may be inverted with an NPN BJT then connected

to the enable pin of the GPS module.

Figure 5-4 Inverting Gate Control signal to enable GPS module(active high enable)

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

6 USB Error Detection

Pin 32 of the device is provided to indicate a problem has occurred with the USB connection. The errors

are USB device not supported, USB hub not supported and USB device not responding. USB device not

supported would occur if the USB port was connected to a non-Android class device port. e.g. The

FT312D is not designed to host memory sticks or printers etc. USB hub not supported would be reported

if FT312D is connected to a USB hub. USB device not responding would occur if the USB device connected

to the FT312D host port did not respond and the enumeration failed. The signal states are as follows:

Pin state

Definition

Logic 0

Device connected to USB and functional

Logic 1

Device not connected

One 50ms logic 0 pulse

Device not responding. This pulse occurs at plug-in

and then the signal returns to logic 1. This then

repeats every second.

Two 50ms logic 0 pulses

Device not supported. These pulses occur at plug-

in and then the signal returns to logic 1. This then

repeats every second.

Three 50ms logic 0 pulses

Hub not supported. These pulses occur at plug-in

and then the signal returns to logic 1. This then

repeats every second.

Table 6.1 Error Detection

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

7 Absolute Maximum Ratings

The absolute maximum ratings for FT312D are shown in Table 7.1. These are in accordance with the

Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the

device.

Parameter

Value

Unit

Storage Temperature

-65°C to 150°C

Degrees C

Floor Life (Out of Bag) At Factory Ambient

( 30°C / 60% Relative Humidity)

168 Hours

(IPC/JEDEC J-STD-033A MSL Level 3

Compliant)*

Hours

Ambient Temperature (Power Applied)

-40°C to 85°C

Degrees

C.

Vcc Supply Voltage

0 to +3.63

V

VCCIO

0 to +3.63

V

AVCC

0 to + 1.98

V

DC Input Voltage - USBDP and USBDM

-0.5 to +(Vcc +0.5)

V

DC Input Voltage - High Impedance

Bidirectional

-0.5 to +5.00

V

DC Input Voltage - All other Inputs

-0.5 to +(Vcc +0.5)

V

DC Output Current - Outputs

4

mA

DC Output Current - Low Impedance

Bidirectional

4

mA

Table 7.1 Absolute Maximum Ratings

* If devices are stored out of the packaging beyond this time limit the devices should be baked

before use. The devices should be ramped up to a temperature of 125°C and baked for up to 17

hours.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

7.1 DC Characteristics

DC Characteristics (Ambient Temperature -40˚C to +125˚C)

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Vcc1

VCC Operating Supply

Voltage

2.97

3.3

3.63

V

Vcc2

VCCIO Operating Supply

Voltage

2.97

3.3

3.63

V

AVCC

VCC_PLL Operating

Supply Voltage

1.62

1.8

1.98

V

Icc1

Operating Supply Current

48MHz

25

mA

Normal

Operation

Icc2

Operating Supply Current

128

µA

USB Suspend

Table 7.2Operating Voltage and Current

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Voh

Output Voltage High

2.4

V

I source = 8mA

Vol

Output Voltage Low

0.4

V

I sink = 8mA

Vin

Input Switching

Threshold

1.5

V

Table 7.3I/O Pin Characteristics

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

UVoh

I/O Pins Static Output

( High)

2.8

V

UVol

I/O Pins Static Output

( Low )

0.3

V

UVse

Single Ended Rx

Threshold

0.8

2.0

V

UCom

Differential Common

Mode

0.8

2.5

V

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

UVdif

Differential Input

Sensitivity

0.2

V

UDrvZ

Driver Output

Impedance

3

6

9

Ohms

Table 7.4USB I/O Pin (USBDP, USBDM) Characteristics

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

VCCK

Power supply of internal

core cells and I/O to core

interface

1.62

1.8

1.98

V

1.8V power

supply

VCC18IO

Power supply of 1.8V

OSC pad

1.62

1.8

1.98

V

1.8V power

supply

TJ

Operating junction

temperature

-40

25

125

°C

Iin

Input leakage current

-10

±1

10

µA

Iin= VCC18IO or

0V

Ioz

Tri-state output leakage

current

-10

±1

10

µA

Table 7.5Crystal Oscillator 1.8 Volts DC Characteristics

7.2 ESD and Latch-up Specifications

Description

Specification

Human Body Mode (HBM)

± 2000V

Machine mode (MM)

± 200V

Charged Device Mode (CDM)

± 500V

Latch-up

> ± 200mA

Table 7.6 ESD and Latch-up Specifications

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

8 Application Examples

The following sections illustrate possible applications of the FT312D.

8.1 USB to UARTConverter

FT312D

1

2

3

4

5

SHIELD

Ferrite

Bead

GND

3V3

GND

VCCIO

VREGOUT

USBDM

USBDP

AVCC

GND

RESET#

100nF

4.7uF

+

TX_ACTIVE

5V Power to USB

VCC

3V3

REGULATOR

5V

27R

100nF

3V3

TXD

RXD

RTS#

CTS#

USB_ERROR

GND

47pF47pF

MCU/FPGA

UART_TXD

UART_RXD

UART_RTS#

UART_CTS#

UART_TX_ACTIVE

620R 3V3

LED

Figure 8.1Application Example showing USB to UART Converter

The UART signals are at 3V3 level and may be used to drive directly into a FPGA or MCU with a 3V3

interface, or could be level shifted with an RS232, RS422 or RS485 transceiver. The TX_ACTIVE signal is

used mostly with RS485 transceivers to enable the Transmit line drivers.

The unused pins may be left unterminated.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

8.2 USB to RS232 Converter

FT312D

1

2

3

4

5

SHIELD

Ferrite

Bead

GND

3V3

GND

VCCIO

VREGOUT

USBDM

USBDP

AVCC

GND

RESET#

100nF

4.7uF

+

TX_ACTIVE

5V Power to USB

VCC

3V3

REGULATOR

5V

27R

100nF

3V3

TXD

RXD

RTS#

CTS#

USB_ERROR

GND

47pF47pF

UART_TXD

UART_RXD

UART_RTS#

UART_CTS#

RS232

LEVEL

CONVERTER

TXD

RXD

RTS

CTS

2

3

7

8

DB9

620R 3V3

LED

5

10

SHIELD

Figure 8.2Application Example showing USB to RS232 Converter

An example of using the FT312D as a USB to RS232 converter is illustrated in Figure 8.2. In this

application, a TTL to RS232 Level Converter IC is used on the serial UART interface of the FT312D to

convert the TTL levels of the FT312D to RS232 levels. This level shift can be done using line drivers from

a variety of vendors e.g. Zywyn.

A suitable level shifting device is the Zywyn ZT3243F which is capable of RS232 communication at up to

1000k baud.

The unused pins may be left unterminated.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

9 Package Parameters

FT312D is available in RoHS Compliant packages, QFN package (32QFN) and an LQFP package (32LQFP).

The packages are lead (Pb) free and use a ‘green’ compound. The package is fully compliant with

European Union directive 2002/95/EC.

The mechanical drawings of the packages are shown in sections 9.2- all dimensions are in millimetres.

The solder reflow profile for all packages can be viewed in Section 9.3.

9.1 FT312D Package Markings

9.1.1 QFN-32

An example of the markings on the QFN package are shown in Figure 9-1. The FTDI part number is too

long for the 32 QFN package so in this case the last two digits are wrapped down onto the date code line.

Figure 9-1QFN Package Markings

1C should be printed on line 4, then a space and then the Date Code.

1. YYWW = Date Code, where YY is year and WW is week number

2. Marking alignment should be centre justified

3. Laser Marking should be used

4. All marking dimensions should be marked proportionally. Marking font should be using

Unisem standard font (Roman Simplex)

FTDI

I

XXXXXXXX

FT312D-32Q

Line 1 – FTDI Logo

Line 4 – Revision and Date

Code

Line 2 – Wafer Lot Number

1

32

Line 3 – FTDI Part Number

1C YYWW

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

9.1.2 LQFP-32

An example of the markings on the LQFP package are shown in Figure 9-2.

Figure 9-2 LQFP Package Markings

Notes:

1. YYWW = Date Code, where YY is year and WW is week number

2. Marking alignment should be centre justified

3. Laser Marking should be used

4. All marking dimensions should be marked proportionally. Marking font should be using Unisem

standard font (Roman Simplex)

FTD

I

XXXXXXXXXX

FT312D-32L

Line 1 – FTDI Logo

Line 4 – Revision, Date Code

Line 2 – Wafer Lot Number

1

32

Line 3 – FTDI Part Number

1C YYWW

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

9.2 FT312DPackage Dimensions

9.2.1 QFN-32 Package Dimensions

1

XXXXXXXX

FTDl

1C YYWW

FT312D-32Q

1

Figure 9-3 QFN-32 Package Dimensions

Note: Dimensions are in mm

Note: The centre pad should be connected to the GND plane for improved thermal conduction and noise

immunity.

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

9.2.2 LQFP-32 Package Dimensions

FTDl

XXXXXXXX

1C YYWW

FT312D-32L

PIN #1

PIN #32

Figure 9-4LQFP-32 Package Dimensions

Note: Dimensions are in mm

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

9.3 Solder Reflow Profile

Figure 9-5 All packages Reflow Solder Profile

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Profile Feature

Pb Free Solder Process

(green material)

SnPb Eutectic and Pb free (non

green material) Solder Process

Average Ramp Up Rate (Ts to Tp)

3°C / second Max.

3°C / Second Max.

Preheat

- Temperature Min (Ts Min.)

- Temperature Max (Ts Max.)

- Time (ts Min to ts Max)

150°C

200°C

60 to 120 seconds

100°C

150°C

60 to 120 seconds

Time Maintained Above Critical Temperature

TL:

- Temperature (TL)

- Time (tL)

217°C

60 to 150 seconds

183°C

60 to 150 seconds

Peak Temperature (Tp)

260°C

see Figure 9-5

Time within 5°C of actual Peak Temperature

(tp)

30 to 40 seconds

20 to 40 seconds

Ramp Down Rate

6°C / second Max.

Time for T= 25°C to Peak Temperature, Tp

8 minutes Max.

6 minutes Max.

Table 9.1Reflow Profile Parameter Values

SnPb Eutectic and Pb free (non green material)

Package Thickness

Volume mm3 < 350

Volume mm3 >=350

< 2.5 mm

235 +5/-0 deg C

220 +5/-0 deg C

≥ 2.5 mm

220 +5/-0 deg C

Pb Free (green material) = 260 +5/-0 deg C

Table 9.2 Package Reflow Peak Temperature

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

10 Contact Information

Head Office – Glasgow, UK

Future Technology Devices International Limited

Unit 1, 2 Seaward Place, Centurion Business Park

Glasgow G41 1HH

United Kingdom

Tel: +44 (0) 141 429 2777

Fax: +44 (0) 141 429 2758

E-mail (Sales)

sales1@ftdichip.com

E-mail (Support)

support1@ftdichip.com

E-mail (General Enquiries)

admin1@ftdichip.com

Branch Office – Taipei, Taiwan

Future Technology Devices International Limited

(Taiwan)

2F, No. 516, Sec. 1, NeiHu Road

Taipei 114

Taiwan, R.O.C.

Tel: +886 (0) 2 8791 3570

Fax: +886 (0) 2 8791 3576

E-mail (Sales)

tw.sales1@ftdichip.com

E-mail (Support)

tw.support1@ftdichip.com

E-mail (General Enquiries)

tw.admin1@ftdichip.com

Branch Office – Oregon, USA

Future Technology Devices International Limited (USA)

7130 SW Fir Loop

Tigard, OR 97223

USA

Tel: +1 (503) 547 0988

Fax: +1 (503) 547 0987

E-Mail (Sales)

us.sales@ftdichip.com

E-Mail (Support)

us.support@ftdichip.com

E-Mail (General Enquiries)

us.admin@ftdichip.com

Branch Office – Shanghai, China

Room 1103, No. 666 West Huaihai Road,

Shanghai, 200052

China

Tel: +86 21 62351596

Fax: +86 21 62351595

E-mail (Sales)

cn.sales@ftdichip.com

E-mail (Support)

E-mail (General Enquiries)

cn.support@ftdichip.com

cn.admin@ftdichip.com

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Appendix A – References

Useful Links

http://www.ftdichip.com/Support/Documents/White_Papers/WP_001_Connecting_%20Peripherals_to_an

_Android_%20Platform.pdf

http://www.ftdichip.com/Support/Documents/ProgramGuides/FT31XD_Android_programmer_guide(FT_0

00532).pdf

Useful utilities and examples firmware

http://www.ftdichip.com/Support/Utilities/FT312D_Configuration_V010000.zip

http://www.ftdichip.com/Support/SoftwareExamples/Android_Projects.htm

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Appendix B - List of Figures and Tables

List of Figures

Figure 2.1FT312D Block Diagram .................................................................................................... 3

Figure 3.1QFN Schematic Symbol ................................................................................................... 6

Figure 5-1 UART Receive Waveform .............................................................................................. 10

Figure 5-2 UART Transmit Waveform ............................................................................................ 10

Figure 5-3 UART RXD and TXD connection gated by Enumeration ..................................................... 11

Figure 5-4 Inverting Gate Control signal to enable GPS module(active high enable) ............................ 11

Figure 8.1Application Example showing USB to UART Converter ....................................................... 16

Figure 8.2Application Example showing USB to RS232 Converter ...................................................... 17

Figure 9-1QFN Package Markings .................................................................................................. 18

Figure 9-2 LQFP Package Markings ................................................................................................ 19

Figure 9-3 QFN-32 Package Dimensions ........................................................................................ 20

Figure 9-4LQFP-32 Package Dimensions ........................................................................................ 21

Figure 9-5 All packages Reflow Solder Profile ................................................................................. 22

List of Tables

Table 3.1 Power and Ground .......................................................................................................... 6

Table 3.2 Function pins ................................................................................................................. 7

Table 4.1Default Descriptor Strings ................................................................................................. 9

Table 6.1 Error Detection ............................................................................................................. 12

Table 7.1 Absolute Maximum Ratings ............................................................................................ 13

Table 7.2Operating Voltage and Current ........................................................................................ 14

Table 7.3I/O Pin Characteristics .................................................................................................... 14

Table 7.4USB I/O Pin (USBDP, USBDM) Characteristics ................................................................... 15

Table 7.5Crystal Oscillator 1.8 Volts DC Characteristics ................................................................... 15

Table 7.6 ESD and Latch-up Specifications ..................................................................................... 15

Table 9.1Reflow Profile Parameter Values ...................................................................................... 23

Table 9.2 Package Reflow Peak Temperature .................................................................................. 23

DS_FT312D USB ANDROID HOST IC Datasheet

Version 1.1

Document No.: FT_000816 Clearance No.: FTDI# 331

Appendix C - Revision History

Document Title: USB Android Host ICDS_FT312D

Document Reference No.: FT_000816

Clearance No.: FTDI# 331

Product Page: http://www.ftdichip.com/FTProducts.htm

Document Feedback: Send Feedback

Version 1.0 Initial Release Feb2013

Version 1.1 Note added on USB enumeration to be completed before

Receiving data in RXD Nov 2013

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

FTDI:

FT312D-32L1C-T FT312D-32Q1C-T FT312D-32L1C-R FT312D-32Q1C-R