CPC1961G AC Solid State Relay Blocking Voltage Load Current 1 On State Voltage Drop 1 CPC1961G 600 200 3.0 Units VP mA Vrms (at IL = 250mA) One Pole Operating Features * Load Current up to 200 mA * 600V Blocking Voltage * 5mA Sensitivity * Zero-Crossing Detection * DC Control, AC Output * Optically Isolated * TTL and CMOS Compatible * Low EMI and RFI Generation * High Noise Immunity * Machine Insertable, Wave Solderable * Flammability classification rating of V-0 Applications * Programmable Control * Process Control * Power Control Panels * Remote Switching * Gas Pump Electronics * Contactors * Large Relays * Solenoids * Motors * Heaters Description The CPC1961G is a dual pole AC solid state switch that uses optical coupling with dual monolithic SCR outputs to produce an alternative to optocoupler and triac circuits. The CPC1961G switches are robust enough to provide a blocking voltage of up to 600V. In addition, tightly controlled zero cross circuitry ensures switching of AC loads without the generation of transients. The input and output circuits are optically coupled to provide 3750Vrms of isolation and noise immunity between control and load circuits. As a result the CPC1961G is well suited for industrial environments where electromagnetic interference would disrupt the operation of electromechanical relays. The CPC1961G is offered in a space saving 8 pin DIP package with two independent switches. Approvals * UL recognized; File #E69938 Ordering Information Part # CPC1961G CPC1961GS CPC1961GSTR Description 8 Pin Dip (50/Tube) 8 Pin Surface Mount (50/Tube) 8 Pin Surface Mount (1000/Reel) Pin Configuration CPC1961G Pinout 8 AC Load + LED 1 ZC - LED 2 7 AC Load + LED 3 6 AC Load ZC - LED 4 DS-CPC1961G-R02 www.clare.com 5 AC Load 1 CPC1961G Absolute Maximum Ratings (@ 25 C) Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Package Dissipation 2 Isolation Voltage Input to Output Operational Temperature Storage Temperature Ratings Units 600 VP 5 VP 50 mA 1 A 150 mW 800 mW 3750 Vrms -40 to +85 C -40 to +125 C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. 1 Derate Linearly 1.33 mW/C 2 Derate Linearly 6.67 mW/C Electrical Characteristcs Parameters Output Characteristics @ 25C Operating Voltage Range Load Current 4 Non-repetitive Single Cycle Surge Current Off State Leakage Current On-State Voltage Drop Critical Rate of Rise 3 Switching Speeds Turn-on Turn-off Zero-Cross Turn-On Voltage Operating Frequency 1 Load Power Factor for Guaranteed Turn-On 2 Input Characteristics @ 25C Input Control Current For Normal Environment For High Noise Environment Input Voltage Drop Input Drop-out Voltage Reverse Input Current Common Characteristics @ 25C Input to Output Capacitance Conditions Symbol Min Typ Max Units VT VL=120-260Vrms, Continuous VDRM IL=250 mA - IL 20 0.005 1000 - 240 200 1.0 1 3.0 - Vrms mArms A mA Vrms V/s 20 0.25 5 - 0.5 0.5 20 5 400 - cycles cycles V V Hz - 1.2 - 1.4 10 mA mA V V A 3 - pF ITSM ILEAK dv/dt IF=5 mA IF=5 mA 1st half cycle Sub. half cycle 60 Hz TON TOFF IF=5mA VR=5V IF IF VF IR 5 10 0.9 0.8 - - CI/O - 1 PF Zero Cross 1st half cycle @ <100Hz 2 Snubber circuits may be required at low power factors. 3 Tested in accordance with EIA/NARM standard RS-443. 4 Maximum current with one pole operating. Maximum continuous load current with both poles operating simultaneously is 110mA. 2 www.clare.com Rev. 2 Manufaturing Information Soldering Recommended soldering processes are limited to 245C component body temperature for 10 seconds. Washing Clare does not recommend ultrasonic cleaning or the use of chlorinated solvents. MICHANICAL DIMENSIONS PC Board Pattern (Top View) 8 Pin DIP Through Hole (Standard) 8-0.800 DIA. (8-0.031 DIA.) 7.239 TYP. (0.285) 3.302 (0.130) 9.144 TYP. (0.360) 8 Pin Surface Mount ("S" Suffix) PC Board Pattern (Top View) 3.302 (0.130) 0.635 TYP. (0.025) 0.254 TYP. (0.010) Tape and Reel Packaging for 8 Pin Surface Mount Package 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) 1 8 W = 16.30 max (0.642 max) Bo = 10.30 (0.406) Top Cover Tape Embossed Carrier P = 12.00 (0.472) Embossment K1 = 4.20 (0.165) Ao = 10.30 (0.406) Dimensions: mm (inches) User Direction of Feed K0 = 4.90 (0.193) NOTE: Tape dimensions not shown, comply with JEDEC Standard EIA-481-2 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare's Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-CPC1961G-R02 (c)Copyright 2005, Clare, Inc. All rights reserved. Printed in USA. 2/23/04