D WIMA FKS 3 Polyester (PET) Film/Foil Capacitors for Pulse Applications in PCM 7.5 mm to 15 mm. Capacitances from 1000 pF to 0.22 mF. Rated Voltages from 100 VDC to 630 VDC. Special Features Electrical Data Pulse duty construction According to RoHS 2011/65/EU Typical Applications For general DC-applications e.g. Coupling Decoupling Construction Dielectric: Polyethylene-terephthalate (PET) film Capacitor electrodes: Metal foil Internal construction: Capacitance range: 1000 pF to 0.22 mF (E12-values on request) Rated voltages: 100 VDC, 250 VDC, 400 VDC, 630 VDC Capacitance tolerances: 20%, 10%, 5%, Operating temperature range: -55+ C to +100+ C Test specifications: In accordance with IEC 60384-11 Climatic test category: 55/100/56 in accordance with IEC Insulation resistance at +20+ C: 1 x 10 5 M Measuring voltage: 100 V/1 min. Test voltage: 2 Ur, 2 sec. Maximum pulse rise time: 1000 V/msec for pulses equal to the rated voltage Dissipation factors at +20+ C: tan d at f 1 kHz 10 kHz 100 kHz C0,22mF 7x10 -3 15x10-3 20x10-3 Voltage derating: A voltage derating factor of 1.25 % per K must be applied from +85+ C for DC voltages and from +75+ C for AC voltages. Reliability: Operational life 300000 hours Failure rate 5 fit (0.5 x U r and 40+ C) Plastic film Metal foil electrode Terminating wire Mechanical Tests Pull test on pins: 10 N in direction of pins according to IEC 60068-2-21 Vibration: 6 hours at 10...2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 4000 bumps at 390 m/sec 2 in accordance with IEC 60068-2-29 Packing Available taped and reeled. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. 01.19 Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire. Marking: Colour: Red. Marking: Black. 37 D WIMA FKS 3 Continuation General Data Capacitance W H L 100 VDC/63 VAC* PCM** Part number W 250 VDC/160 VAC* PCM** Part number H L 1000 pF 3 8.5 10 7.5 FKS3D011002B00____ 1500 3 8.5 10 7.5 FKS3D011502B00____ 2200 3 8.5 10 7.5 FKS3D012202B00____ 3300 3 8.5 10 7.5 FKS3D013302B00____ 4700 3 8.5 10 7.5 FKS3D014702B00____ 6800 3 8.5 10 7.5 FKS3D016802B00____ 38.5 38.5 38.5 38.5 38.5 3 9 38.5 3 9 107.5 107.5 107.5 107.5 107.5 13 10 107.5 13 10 0.01 0.015 0.022 0.033 0.047 0.068 39 13 10 FKS3F021003A00____ 49.5 13 10 FKS3F021503D00____ 5 13 10 FKS3F022203F00____ mF 0.1 mF 0.15 0.22 38.5 3 9 3 8.5 39 3 8.5 39 49.5 49.5 5 11 107.5 13 10 10 7.5 13 10 10 7.5 13 10 13 10 13 10 13 10 6 7 8 13 18 18 12 14 15 FKS3D021002B00____ FKS3D021003A00____ FKS3D021502B00____ FKS3D021503A00____ FKS3D022202B00____ FKS3D022203A00____ FKS3D023303D00____ FKS3D024703D00____ FKS3D026803F00____ 11 FKS3F011002B00____ FKS3F011502B00____ FKS3F012202B00____ FKS3F013302B00____ FKS3F014702B00____ FKS3F014703A00____ FKS3F016802B00____ FKS3F016803A00____ 6 12 13 10 FKS3F023303G00____ 6 12.51815 FKS3F024704C00____ 7 14 18 15 FKS3F026804D00____ 10 FKS3D031003G00____ 15 FKS3D031504D00____ 15 FKS3D032204F00____ 8 9 15 16 18 18 15 FKS3F031004F00____ 15 FKS3F031504J00____ * AC voltage: f = 50 Hz; 1.4 x Urms + UDC U r ** PCM = Printed circuit module = pin spacing. Dims. in mm. Part number completion: W The values of the WIMA FKM 3 range according to the main catalogue 2009 are still available on request. L H 6 -2 d PCM at the pin exit points ( 0.4) Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk= S Pin length: 6-2 = SD Tapedversionseepage149. d = 0.5 P if W = 3 PCM 7.5 and 10 d = 0.6 P if W 4 d = 0.8 P if PCM = 15 Rights reserved to amend design data without prior notification. 01.19 Continuation page 39 38 D WIMA FKS 3 Continuation General Data Capacitance W 1000 1500 2200 3300 4700 6800 pF 39 39 39 39 39 39 13 13 13 13 13 13 10 10 10 10 10 10 FKS3G011003A00____ FKS3G011503A00____ FKS3G012203A00____ FKS3G013303A00____ FKS3G014703A00____ FKS3G016803A00____ 3 9 13 10 FKS3J011003A00____ 3 9 13 10 FKS3J011503A00____ 3 9 13 10 FKS3J012203A00____ 4 9.51310 FKS3J013303D00____ 49.5 13 10 FKS3J014703D00____ 5 11 13 10 FKS3J016803F00____ 0.01 0.015 0.022 0.033 0.047 0.068 mF 4 9.5 5 11 6 12 6 12.5 7 14 8 15 13 13 13 18 18 18 10 10 10 15 15 15 FKS3G021003D00____ FKS3G021503F00____ FKS3G022203G00____ FKS3G023304C00____ FKS3G024704D00____ FKS3G026804F00____ 6 12 13 10 FKS3J021003G00____ 6 12.51815 FKS3J021504C00____ 7 14 18 15 FKS3J022204D00____ 8 15 18 15 FKS3J023304F00____ 9 18 15 FKS3G031004J00____ 0.1 mF H 16 L 400 VDC/250 VAC* PCM** Part number W H 630 VDC/300 VAC* PCM** Part number L * AC voltage: f = 50 Hz; 1.4 x Urms + UDC U r ** PCM = Printed circuit module = pin spacing. Part number completion: W Dims. in mm. The values of the WIMA FKM 3 range according to the main catalogue 2009 are still available on request.. L H 6 -2 d PCM at the pin exit points ( 0.4) Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk= S Pin length: 6-2 = SD Tapedversionseepage149. d = 0.5 P if W = 3 PCM 7.5 and 10 d = 0.6 P if W 4 d = 0.8 P if PCM = 15 Rights reserved to amend design data without prior notification. 01.19 Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide). 39 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Internal temperature of the capacitor must be kept as follows: Polyester: preheating:T max. T 125 C soldering:T max. T 135 C Polypropylene:preheating: Tmax. T 100 C soldering:T max. T 110 C Single wave soldering Soldering bath temperature: TP 260 C Dwell time: t P 5 sec Double wave soldering Soldering bath temperature: TP 260 C Dwell time: St P 5 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. WIMA Quality and Environmental Philosophy ISO 9001:2015 Certification ISO 9001:2015 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2015 of our factories by the infaz (Institut fur Auditierung und Zertifizierung) certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application during production process: All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. - - - - - Lead PCB CFC Hydrocarbon chloride Chromium 6+ - - - - - PBB/PBDE Arsenic Cadmium Mercury etc. We merely use pure, recyclable materials for packing our components, such as: "carton "cardboard "adhesive tape made of paper "polystyrene We almost completely refrain from using packing materials such as: "adhesive tapes made of plastic "metal clips RoHS Compliance According to the RoHS Directive 2011/65/EU as amended from time to time certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. WIMA Kondensatoren sind bleifrei konform RoHS 2011/65/EU WIMA capacitors are lead free in accordance with RoHS 2011/65/EU Tape for lead-free WIMA capacitors DIN EN ISO 14001:2004 WIMA's environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2004 to optimize the production processes with regard to energy and resources. 01.19 "incoming material inspection "metallization "film inspection "schoopage "pre-healing "pin attachment "cast resin preparation/ encapsulation "100% final inspection "Testing as per customer requirements WIMA Environmental Policy 15 D Typical Dimensions for Taping Configuration Vh P P2 Diagram 1: PCM 2.5/5/7.5mm W W1 W0 H H1 W2 P1 D0 d P t F P0 H1 P P1 H P1 d d F P0 P2 Diagram 2: PCM 10/15 mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Designation Carrier tape width Dimensions for Radial Taping Symbol PCM 2.5 taping W P0 P2 F PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping 18.0 p0.518.0 p0.518.0 p0.518.0 p0.518.0 p0.518.0 p0.518.0 p0.5 for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing Hold-down tape width W06.0 6.0 12.0 12.0 12.0 12.0 12.0 adhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tape Hole position W19.0 p0.59.0 p0.59.0 p0.59.0 p0.59.0 p0.59.0 p0.59.0 p0.5 Hold-down tape position W 2 Feed hole diameter D04.0 p0.24.0 p0.24.0 p0.24.0 p0.24.0 p0.24.0 p0.24.0 p0.2 P 12.7 p1.012.7 p1.012.7 p1.025.4 p1.025.4 p1.038.1 p1.53*8.1p1.5 or 50.8p1.5 0.5 to 3.0 max. Pitch of component Feed hole pitch P012.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 0.5 to 3.0 max. 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 0.5 to 3.0 max. 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 0.5 to 3.0 max. 12.7 p0.3 0.5 to 3.0 max. cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 0.5 to 3.0 max. 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 0.5 to 3.0 max. 12.7 p0.3 Feed hole centre to pin P15.1 p0.53.85 p0.72.6 p0.77.7 p0.75.2 p0.77.8 p0.75.3 p0.7 Hole centre to component centre P26.35 p1.36.35 p1.36.35 p1.312.7 p1.312.7 p1.319.05 p1.319.05 p1.3 Feed hole centre to bottom H edge of the component cumulative pitch error max. 1.0 mm/20 pitch 16.5 p0.316.5 p0.316.5 p0.516.5 p0.516.5 p0.516.5 p0.516.5 p0.5 18.5 p0.518.5 p0.518.5 p0.518.5 p0.518.5 p0.518.5 p0.518.5 p0.5 Feed hole centre to top H+Hcomponent < H1H+Hcomponent < H1H+Hcomponent < H1H+Hcomponent < H1H+Hcomponent < H1H+Hcomponent < H1H+Hcomponent < H1 H edge of the component1 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0 Pin spacing at +0.8 F2.5 p0.55.0 7.5 p0.810.0 p0.815 p0.822.5 p0.827.5 p0.8 upper edge of carrier tape -0.2 Pin diameter d 0.4 p0.050.5 p0.05 Component alignment Dh p 2.0 max. Total tape thickness t p 2.0 max. +0.06+0,06 +0,08+0,08+0.08 0.5 p0.05 or 0.6 -0.05 0.5 p0.05 or 0.6 -0.050.8 -0.050.8 -0.050.8 -0.05 p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. 0.6 p0.20.6 p0.20.6 p0.20.6 p0.20.6 p0.20.6 p0.20.6 p0.2 ROLL/AMMO Package (see also page 150) 52 p2 depending on P 360 max. B p2 comp. dimensions REEL P 30 p158 Unit AMMO 52 p254 p2 500 max. B60 p2 REEL P 360 max. B58 p2 or REEL PP 25 p1 P 30 p166 p2 68 p2 depending on PCM and component dimensions see details page 151. Dims in mm. 01.19 Diameter of pins see General Data. Please clarify customer-specific deviations with the manufacturer. * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible 149 D Types of Tape Packaging of Capacitors for Automatic Radial Insertion REEL Packaging 340 max. 301 251 360 max. 500 max. AMMO Packaging 340 max. 370 max. ROLL Packaging 34 0m ax. 50 max. 50 max. 70 max. . ax 0 m ax. 34 0 m 49 B BAR CODE (Labelling) Labelling of package units in plain text and with alphanumerical Bar Code BARCODE Code 39" Scanner decoding of WIMA supplier number Customer`s P/O number Customer`s part number WIMA confirmation number WIMA part number Lot number Date code Quantity In addition part description of - - - - - - article capacitance value rated voltage dimensions capacitance tolerance packing 01.19 as well as gross weight and customer`s name are indicated in plain text. 150 D Packing Quantities for Capacitors with Radial Pins in PCM 2.5 mm to 22.5 mm Size PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm W 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 H 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 bulk L 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 Codes 0B 0C 0D 0E 0F 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 1M 1N 2A 2B 2C 2D 2E 2F 2G 3A FA 3C 3D FB 3F 3G 3H 3I 4B FC 4C FD 4D FE 4F FF 4H 4J FG 4M 5A 5B 5D FH 5F FI 5G 5H 5I FJ S 5000 5000 5000 5000 5000 5000 5000 5000 6000 4000 3500 4000 2500 2500 2500 2000 2000 1500 1000 5000 5000 4000 3500 3000 2000 1500 3000 3000 3000 3000 2000 3000 2400 2400 2000 2400 1000 2000 1000 1600 1000 1200 500 1200 900 500 1000 1200 1000 760 500 500 570* 594* 594* 561* 480* Moulded versions. Rights reserved to amend design data without prior notification. 01.19 * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D 2200 2500 - 2800 - 2000 2300 - 2300 - 1500 1800 - 1800 - 1200 1500 - 1500 - 900 1200 - 1200 - 2200 2500 - 2800 - 2000 2300 - 2300 - 1600 2000 - 2000 - 1300 1500 - 1500 - 1300 1500 - 1500 - 1100 1400 - 1400 - 1000 1200 - 1200 - 1000 1200 - 1200 - 800 1000 - 1000 - 700 1000 - 1000 - 700 950 - 1000 - 600 800 - 800 - 600 800 - 800 - 500 600 - 640 - - 2500 4400 2500 - - 2200 4300 2300 4150 - 1700 3200 1700 3100 - 1500 2900 1400 2700 - 1300 2500 1300 - - 1000 2200 1100 - - 900 1800 1000 - - 1100 2200 - 1900 - 900 1600 - 1450 - 900 1600 - 1450 - 900 1600 - 1400 - 700 1300 - 1200 - 700 1300 - 1200 - 550 1100 - 1000 - 550 1100 - 1000 - 400 800 - 740 - 600 1200 - 1150 - 600 1200 - 1200 - 500 1000 - 1000 - 500 1000 - 1000 - 450 900 - 850 - 450 900 - 850 - 400 800 - 740 - 400 800 - 740 - 350 700 - 650 - 350 700 - 650 - 300 650 - 590 - 300 600 - 540 - - 800 - 770 - - 700 - 640 - - 600 - 550 - - 500 - 480 - - 480 - 450 - - 420 - 380 - - 400 - 360 - - 400 - 360 - - 380 - 350 - - 350 - 310 ROLL 151 D Packing Quantities for Capacitors with Radial Pins in PCM 27.5 mm to 52.5 mm Size PCM pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D - - 460/340* - 420 - - 380/280* - 350 - - 300 - 290 - - - - - 270 - 250 - - - - - - - - - - - - - - - - - - - - - - - - - - - ROLL bulk W 9 11 13 13 15 15 17 17 20 20 H 19 21 24 25 26 26 29 34.5 32 39.5 L 31.5 31.5 31.5 33 31.5 33 31.5 31.5 33 31.5 Codes 6A 6B 6D FK 6F FL 6G 6I FM 6J S 567* 459* 378* 405* 324* 324* 198* 198* 162* 162* 37.5 mm 9 11 13 15 17 19 20 24 31 35 40 19 22 24 26 29 32 39.5 45.5 46 50 55 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 7A 7B 7C 7D 7E 7F 7G 7H 7I 7J 7K 441* 357* 294* 252* 154* 140* 126* 112* 84* 35* 28* - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 48.5 mm 19 23 27 33 37 31 34 37.5 48 54 56 56 56 56 56 8D 8E 8H 8J 8L 120* 80* 84* 25* 25* - - - - - - - - - - - - - - - - - - - - - - - - - 45 45 50 55 65 57 57 57 57 57 9D 9E 9F 9H 9J 70* 60* 25* 20* 20* - - - - - 52.5 mm 25 30 35 45 45 - - - - - - - - - - 27.5 mm * for 2-inch transport pitches. * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. Moulded versions. Rights reserved to amend design data without prior notification. 01.19 Updated data on www.wima.com 152 D WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: Field 1 - 4:Type description Field 5 - 6:Rated voltage Field 7 -10:Capacitance Field11 -12:Size and PCM Field13 -14:Version code (e.g. Snubber versions) Field15: Capacitance tolerance Field16: Packing Field17 -18:Pin length (untaped) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D 20% bulk MKS 2 01.19 Type description: SMD-PET = SMDT SMD-PEN = SMDN SMD-PPS = SMDI FKP 02 = FKP0 MKS 02 = MKS0 FKS 2 = FKS2 FKP 2 = FKP2 FKS 3 = FKS3 FKP 3 = FKP 3 MKS 2 = MKS2 MKP 2 = MKP2 MKS 4 = MKS4 MKP 4C = MKPC MKP 4 = MKP4 MKP 10 = MKP1 FKP 1 = FKP1 MKP-X2 = MKX2 MKP-X1 R = MKX1 MKP-Y2 = MKY2 MP 3-X2 = MPX2 MP 3-X1 = MPX1 MP 3-Y2 = MPY2 MP 3R-Y2 = MPRY MKP 4F = MKPF Snubber MKP = SNMP Snubber FKP = SNFP GTO MKP = GTOM DC-LINK MKP 3 = DCP3 DC-LINK MKP 4 = DCP4 DC-LINKMKP4S = DCPS DC-LINK MKP 5 = DCP5 DC-LINK MKP 6 = DCP6 DC-LINK HC = DCHC DC-LINK HY = DCHY 63 VDC Rated voltage: 50 VDC = B0 63 VDC = C0 100 VDC = D0 250 VDC = F0 400 VDC = G0 450 VDC = H0 520 VDC = H2 600 VDC = I0 630 VDC = J0 700 VDC = K0 800 VDC = L0 850 VDC = M0 900 VDC = N0 1000 VDC = O1 1100 VDC = P0 1200 VDC = Q0 1250 VDC = R0 1500 VDC = S0 1600 VDC = T0 2000 VDC = U0 2500 VDC = V0 3000 VDC = W0 4000 VDC = X0 6000 VDC = Y0 250 VAC = 0W 275 VAC = 1W 300 VAC = 2W 305 VAC = AW 350 VAC = BW 440 VAC = 4W 500 VAC = 5W ... 0.01 mF Capacitance: 22 pF = 0022 47 pF = 0047 100 pF = 0100 150 pF = 0150 220 pF = 0220 330 pF = 0330 470 pF = 0470 680 pF = 0680 1000 pF = 1100 1500 pF = 1150 2200 pF = 1220 3300 pF = 1330 4700 pF = 1470 6800 pF = 1680 0.01 mF = 2100 0.022 mF = 2220 0.047 mF = 2470 0.1 mF = 3100 0.22 mF = 3220 0.47 mF = 3470 = 4100 1 mF 2.2 mF = 4220 4.7 mF = 4470 = 5100 10 mF = 5220 22 mF = 5470 47 mF 100 mF = 6100 220 mF = 6220 1000 mF = 7100 1500 mF = 7150 ... 2.5x6.5x7.2 - Size: 4.8x3.3x3 Size1812 = KA 4.8x3.3x4 Size1812 = KB 5.7x5.1x3.5 Size2220 = QA 5.7x5.1x4.5 Size2220 = QB 7.2x6.1x3 Size2824 = TA 7.2x6.1x5 Size2824 = TB 10.2x7.6x5 Size4030 = VA 12.7x10.2x6 Size5040 = XA 15.3x13.7x7 Size6054 = YA 2.5x7x4.6 PCM2.5 = 0B 3x7.5x4.6 PCM2.5 = 0C 2.5x6.5x7.2 PCM5 = 1A 3x7.5x7.2 PCM5 = 1B 2.5x7x10 PCM7.5 = 2A 3x8.5x10 PCM7.5 = 2B 3x9x13 PCM10 = 3A 4x9x13 PCM10 = 3C 5x11x18 PCM15 = 4B 6x12.5x18 PCM15 = 4C 5x14x26.5 PCM22.5 = 5A 6x15x26.5 PCM22.5 = 5B 9x19x31.5 PCM27.5 = 6A 11x21x31.5 PCM27.5 = 6B 9x19x41.5 PCM37.5 = 7A 11x22x41.5 PCM37.5 = 7B 19x31x56 PCM 48.5 = 8D 25x45x57 PCM 52.5 = 9D ... Version code: Standard = Version A1 = Version A1.1.1 = Version A2 = ... 00 1A 1B 2A Tolerance: 20% = 10% = 5% = 2.5% = 1% = ... 6 -2 M K J H E Packing: AMMO H16.5 340x340 AMMO H16.5 490x370 AMMO H18.5 340x340 AMMO H18.5 490x370 REEL H16.5 360 REEL H16.5 500 REEL H18.5 360 REEL H18.5 500 ROLL H16.5 ROLL H18.5 BLISTER W12 180 BLISTER W12 330 BLISTER W16 330 BLISTER W24 330 Bulk/TPS Standard ... =A =B =C =D =F =H =I =J =N =O =P =Q =R =T =S Pin length (untaped) 3.5 0.5 = C9 6 -2 = SD 16 1 = P1 ... Pin length (taped) none = 00 The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 147