OR-6N137S5M - Orient Technology

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

1

ORIENT

Photocoupler

Product Data Sheet

Name: ORPC-6N137

Customer:_________________

Date: _________________

SHENZHEN ORIENT TECHNOLOGY CO.,LTD.

Block A 3rd Floor No.4 Building,Tian’an Cyber Park,Huangge Rd,LongGang

Dist,Shenzhen,GD

TEL：0755-29681816

FAX：0755-29681200

www.orient-opto.com

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

2

1、Features

(1) 3.3v / 5V supply voltage

(2) low power consumption

(3) high speed: 15MBd(typical)

(4) VCM=1000V, and the lowest common mode inhibition

(CMR) is 10 kv/μs

(5) when - 40 ℃ ~ + 85 ℃ temperature of ac and dc

performance

2、Instructions

6N137 is made up of an efficient AlGaAs light-emitting diode

and high-speed optical detector. This design provides good ac

and dc isolation between the input and output ends of the

photoelectric coupler. The output characteristic of the

photodetector is a collector open circuit schottky clamp transistor.

The total mode transient immunity should reach 10 kv/pa at 3.3 v.

The photoelectric coupler operating temperature range: -

40 ℃ ~ + 85 ℃.

3、Application Range

• line receiver isolation

•A/ D, D/A converted digital signal isolation

• eliminate noise from the ground loop

• switching power supply

• alternative pulse transformers

• motor control system

• interface of microprocessor system, computer and peripheral equipment

4、Functional Diagram

1.NC 5.GND

2.Anode 6.Output

3.Cathode 7.VE(Enable)

4.NC 8.Vcc

0.1 capacitor F bypass capacitance needs to be connected between A Pin8 and Pin5

Truth table

Input（LED）

Enable

Output

ON

H

L

OFF

H

ON

L

H

OFF

L

H

ON

NC

L

OFF

NC

H

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

3

5、Absolute Maximum Ratings (Ta=25℃)*1

Parameter

Symbol

Rated Value

Unit

Input

Average Forward Input Current

IF

20

mA

Reverse Input Voltage

VR

5

V

Power Dissipation

PI

40

mV

Enable Input Voltage

VE

VCC+0.5

V

Enable Input current

IE

5

mA

Output

Output Collector Current

IO

50

mA

Output Collector Voltage

VO

7

V

Output Collector Power Dissipation

PO

85

mW

Supply Voltage

VCC

7

V

Insulation Voltage

Viso

5000

Vrms

Working Temperature

Topr

-40 ～ + 85

℃

Storage Temperature

Tstg

-55～ + 125

*2 Soldering Temperature

Tsol

260

*1. Room temperature = 25 ℃. Exceeding the maximum absolute rating can permanently damage the device.

Working long hours at the maximum absolute rating can affect reliability.

*2. soldering time is 10 seconds.

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

4

6、Recommended Operating Conditions

Parameter

Symbol

Min

Max

Unit

Operating Temperature

TA

-40

85

℃

Supply Voltage

VCC

2.7

3.6

V

4.5

5.5

Low Level Input Current

IFL

0

250

μA

High Level Input Current

IFH

5

15

mA

Low Level Enable Voltage

VEL

0

0.8

V

High Level Enable Voltage

VEH

2

VCC

V

Output Pull-up Resistor

RL

330

4k

Ω

Fan Out (at RL=1kΩ per

channel)

N

—

5

TTL Loads

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

5

7、Opto-electronic Characteristics

Recommended temperature range (TA= -40℃—+85℃,2.7V≤VCC≤3.6 V),IF= 7.5mA Unless otherwise

stated. Typical valuesTA=25℃,VCC = 3.3 V.

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Input

Forward voltage

VF

IF= 10mA

—

1.38

1.7

V

Temperature Coefficient OF

Forward Voltage

ΔVF/ ΔT

IF= 10mA

—

-1.5

—

mV/℃

Reverse Voltage

BVR

IR= 10μA

5

—

V

Input Threshold Current

ITH

VE=2V,VCC=3.3V

VO=0.6V

IOL (sinking) =13mA

—

1.5

5

mA

Input Capacitance

CIN

f = 1MHz, VF = 0V

—

34

—

pF

Detector

High Level Supply Current

ICCH

VE= 0.5V,

VCC=3.3V,IF=0mA

—

3.8

10

μA

Low Level Supply Current

ICCL

VE= 0.5V,

VCC= 3.3V,IF=10mA

—

5.8

13

mA

High Level Enable Current

IEH

VCC= 3.3V,VE=2V

—

-0.19

-1.6

mA

Low Level Enable Current

IEL

VCC= 3.3V,VE=0.5V

—

-0.41

-1.6

mA

High Level Enable Voltage

VEH

2

—

V

Low Level Enable Voltage

VEL

—

0.8

V

High Level Output Current

IOH

VE=2V, VCC=3.3V，

VO=3.2V,IF=250μA

—

5

100

μA

Low Level Output Voltage

VOL

VE=2V, VCC=3.3V，

IF=5mA,

IOL (sinking) = 13mA

—

0.3

0.6

V

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

6

Recommended temperature range(TA= -40℃—+85℃,4.5V≤VCC≤5.5V),IF= 7.5mA Unless otherwise stated.

Typical values TA=25℃,VCC = 5.0V.

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Input

Forward voltage

VF

IF= 10mA

—

1.38

1.7

V

Temperature Coefficient OF

Forward Voltage

ΔVF/ ΔT

IF= 10mA

—

-1.5

—

mV/℃

Reverse Voltage

BVR

IR= 10μA

5

—

V

Input Threshold Current

ITH

VCC=5.5V,VO=0.6V

IOL>13mA

—

1.35

5

mA

Input Capacitance

CIN

f = 1MHz, VF= 0V

—

34

—

pF

Detector

High Level Supply Current

ICCH

VE= 0.5V,

VCC=5.5V,IF=0mA

—

6.1

10

μA

Low Level Supply Current

ICCL

VE= 0.5V,

VCC= 5.5V,IF=10mA

—

8.3

13

mA

High Level Enable Current

IEH

VCC= 5.5V,VE=2V

—

-0.6

-1.6

mA

Low Level Enable Current

IEL

VCC= 5.5V,VE=0.5V

—

-0.9

-1.6

mA

High Level Enable Voltage

VEH

2

—

V

Low Level Enable Voltage

VEL

—

0.8

V

High Level Output Current

IOH

VE=2V, VCC=5.5V，

VO=5.5V,IF=250μA

—

0.9

100

μA

Low Level Output Voltage

VOL

VE=2V, VCC=5.5V，

IF=5mA,

IOL (sinking) = 13mA

—

0.3

0.6

V

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

7

8、Switching Characteristics

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Propagation delay time to output

High level

tPLH

RL=350Ω

CL=15pF

25

48

90

ns

Propagation delay time to output

Low level

tPHL

25

35

75

ns

Pulse Width Distortion

|tPLH-tPHL|

—

13

—

ns

Output Rise Time (10 to

90%)

tr

—

21

—

ns

Output Fall Time (90 to 10%)

tf

—

6.6

—

ns

Propagation Delay Time of

Enable from VEH to VEL

tELH

RL=350Ω

CL=15pF

VEL=0V

VEH=3V

—

27

—

ns

Propagation Delay Time of

Enable from VEL to VEH

tEHL

—

9

—

ns

Recommended temperature range (TA= -40℃—+85℃,2.7V≤VCC≤3.6 V),IF= 7.5mA Unless otherwise

stated. Typical values TA=25℃,VCC = 3.3 V。

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Propagation delay time to output

High level

tPLH

TA=25 ℃

RL=350 Ω

CL=15pF

25

40

75

ns

—

100

Propagation delay time to output

Low level

tPHL

25

32

75

ns

—

100

Pulse Width Distortion

|tPLH-tPHL|

RL=350Ω

CL=15pF

—

8

—

ns

Output Rise Time (10 to 90%)

tr

—

22

—

ns

Output Fall Time (90 to 10%)

tf

—

6.9

—

ns

Propagation Delay Time of

tELH

RL=350Ω

—

28

—

ns

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

8

Enable from VEH to VEL

CL=15pF

VEL=0V VEH=3V

Propagation Delay Time of

Enable from VEL to VEH

tEHL

—

12

—

ns

Recommended temperature range (TA= -40℃—+85℃,4.5V≤VCC≤5.5V),IF= 7.5mA Unless otherwise stated.

Typical values TA=25℃,VCC = 5.0 V。

Recommended temperature range (TA=40℃-85℃) Unless otherwise stated. Typical values TA=25℃.

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Logic High Common

Mode Transient Immunity

|CMH|

VCC=3.3V,VCM=1000V,RL=350Ω

IF=0mA,TA=25℃

10

15

—

kV/μs

VCC=5V,VCM=1000V,RL=350Ω

IF=0mA,TA=25℃

10

15

—

Logic Low Common Mode

Transient Immunity

|CML|

VCC=3.3V,VCM=1000V,RL=350Ω

IF=10mA,TA=25℃

10

15

—

kV/μs

VCC=5V,VCM=1000V,RL=350Ω

IF=10mA,TA=25℃

10

15

—

Parameter

Symbol

Condition

Min

Typ

Max

Unit

Input-Output Insulation

Leakage Current

II-O

45% RH,t=5s,

VI-O = 3kV DC,TA=25 C

—

1

μA

Withstand Insulation Test

Voltage

VISO

RH ≤ 50%, t =1min,TA=25℃

5000

—

VRMS

Input-Output Resistance

RI-O

VI-O = 500V DC

—

1012

—

Ω

Input-Output Capacitance

CI-O

f = 1MHz, TA= 25 C

—

1

p

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

9

9、Naming Rule

NOTE：

（1）year Code：

'08' means' 2008 ', '09' means' 2009 'and so on.

（2) Week Code：

01 represents the first week, 02 represents the second

week, and so on.

(3)OR：Manufacturer name, representing manufacturer Shenzhen Orient Components Co.,

Ltd.

(4) Type code: representing type 6N137.

(5)Anode

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

10

10、 Outer Dimension

（1）OR-6N137 （2）OR-6N137M

（3）OR-6N137S

11、Recommended Foot Print Patterns (Mount Pad)

(unit：mm)

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

11

12、Taping Dimensions

（1）OR-6N137-TA

（2）OR-6N137-TA1

type

symbol

Size: mm （ inches ）

bandwidth

W

16±0.3（0.63）

pitch

P0

4±0.1（0.15）

pitch

F

7.5±0.1（0.295）

P2

2±0.1（0.079）

interval

P1

12±0.1（0.472）

Encapsulation

type

TA/TA1

amount （pcs）

1000

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

12

13、Temperature Profile Of Soldering

（1）IR Reflow soldering (JEDEC-STD-020C compliant)

Note: one solder backflow is recommended under the conditions described below in the

temperature and time profile. Do not weld more than three times.

Configuration items

conditions

Preheat

- TSmin

- TSmax

- Time (min to Max（TS）

150˚C

200˚C

90±30 sec

Soldering zone

- temperature （TL）

- time（tL）

217˚C

60～100 sec

Peak Temperature

260˚C

Ramp-up rate

3˚C / sec max.

Drop rate （3˚C / sec max.）

3～6˚C / sec

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

13

（2）Wave soldering (JEDEC22A111 compliant)

One-time welding is recommended under the temperature condition.

Temperature

Time

260+0/-5˚C

10 sec

Preheat temperature

Preheat time

5 to 140˚C

30 to 80 sec

（3）Hand soldering by soldering iron

Single lead welding is allowed in each process and one-time welding is recommended.

Temperature

Time

380+0/-5˚C

3 sec max

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

14

14、Switching time test circuit

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

15

15、Characteristics Curve

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

16

Shenzhen Orient Technology Co ., Ltd ORPC-6N137

17