TDA9109/S LOW-COST DEFLECTION PROCESSOR FOR MULTISYNC MONITORS PRELIMINARY DATA .. .. . HORIZONTAL .. .. . . . . SELF-ADAPTATIVE DUAL PLL CONCEPT 150kHz MAXIMUM FREQUENCY X-RAY PROTECTION INPUT I2C CONTROLS : HORIZONTAL DUTY-CYCLE, H-POSITION, FREE RUNNING FREQUENCY, FREQUENCY GENERATOR FOR BURN-IN MODE SHRINK32 (Plastic Package) VERTICAL VERTICAL RAMP GENERATOR 50 TO 185Hz AGC LOOP GEOMETRY TRACKING WITH VPOS & VAMP I2C CONTROLS : VAMP, VPOS, S-CORR, C-CORR DC BREATHING COMPENSATION I2C GEOMETRY CORRECTIONS .. .. .. . VERTICAL PARABOLA GENERATOR (Pin Cushion - E/W, Keystone, Corner) HORIZONTAL DYNAMIC PHASE (Side Pin Balance & Parallelogram) VERTICAL DYNAMIC FOCUS (Vertical Focus Amplitude) GENERAL SYNC PROCESSOR 12V SUPPLY VOLTAGE 8V REFERENCE VOLTAGE HOR. & VERT. LOCK/UNLOCK OUTPUTS READ/WRITE I2C INTERFACE HORIZONTAL AND VERTICAL MOIRE B+ REGULATOR - INTERNAL PWM GENERATOR FOR B+ CURRENT MODE STEP-UP CONVERTER - SOFT START - I2C ADJUSTABLE B+ REFERENCE VOLTAGE - OUTPUT PULSES SYNCHRONIZED ON HORIZONTAL FREQUENCY - INTERNAL MAXIMUM CURRENT LIMITATION ORDER CODE : TDA9109/S . COMPARED WITH THE TDA9109, THE TDA9109/S HAS : - CORNER CORRECTION, - HORIZONTAL MOIRE, - B+ SOFT START, - INCREASED MAX. VERTICAL FREQUENCY, - NO HORIZONTAL FOCUS, - NO STEP DOWN OPTION FOR DC/DC CONVERTER. DESCRIPTION The TDA9109/S is a monolithic integrated circuit assembled in 32-pin shrink dual in line plastic package. This IC controls all the functions related to the horizontal and vertical deflection in multimode or multi-frequency computer display monitors. The internal sync processor, combined with the very powerful geometry correction block make the TDA9109/S suitable for very high performance monitors, using very few external components. The horizontal jitter level is very low. It is particularly well suited for high-end 15" and 17" monitors. Combined with the ST7275 Microcontroller family, TDA9206 (Video preamplifier) and STV942x (On-Screen Display controller) the TDA9109/S allows fully I2C bus controlled computer display monitors to be built with a reduced number of external components. June 1998 This is advance information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1/30 TDA9109/S 2/30 H/HVIN 1 32 5V VSYNCIN 2 31 SDA HLOCKOUT 3 30 SCL PLL2C 4 29 VCC C0 5 28 BOUT R0 6 27 GND PLL1F 7 26 HOUT HPOSITION 8 25 XRAY HMOIRE 9 24 EWOUT FOCUS-OUT 10 23 VOUT HGND 11 22 VCAP HFLY 12 21 VREF HREF 13 20 VAGCCAP COMP 14 19 VGND REGIN 15 18 BREATH ISENSE 16 17 B+GND 9109S-01.EPS PIN CONNECTIONS TDA9109/S PIN CONNECTIONS Pin Name 1 H/HVIN 2 VSYNCIN 3 HLOCKOUT 4 PLL2C 5 C0 6 R0 7 PLL1F 8 HPOSITION 9 HMOIRE 10 FOCUSOUT 11 HGND Horizontal Section Ground 12 HFLY Horizontal Flyback Input (positive polarity) 13 HREF Horizontal Section Reference Voltage (to be filtered) 14 COMP B+ Error Amplifier Output for frequency compensation and gain setting 15 REGIN Regulation Input of B+ control loop 16 ISENSE 17 B+GND 18 BREATH 19 VGND 20 VAGCCAP 21 VREF Function TTL compatible Horizontal sync Input (separate or composite) TTL compatible Vertical sync Input (for separated H&V) First PLL Lock/Unlock Output (0V unlocked - 5V locked) Second PLL Loop Filter Horizontal Oscillator Capacitor Horizontal Oscillator Resistor First PLL Loop Filter Horizontal Position Filter (capacitor to be connected to HGND) Horizontal Moire Output (to be connected to PLL2C through a resistor divider) Vertical Dynamic Focus Output Sensing of external B+ switching transistor current Ground (related to B+ reference adjustment) DC Breathing Input Control (compensation of vertical amplitude against EHV variation) Vertical Section Ground Memory Capacitor for Automatic Gain Control Loop in Vertical Ramp Generator Vertical Section Reference Voltage (to be filtered) 22 VCAP Vertical Sawtooth Generator Capacitor 23 VOUT Vertical Ramp Output (with frequency independant amplitude and S or C Corrections if any). It is mixed with vertical position voltage and vertical moire. 24 EWOUT 26 HOUT Horizontal Drive Output (internal transistor, open collector) 25 XRAY X-RAY protection input (with internal latch function) 27 GND General Ground (referenced to VCC) 28 BOUT 29 VCC Supply Voltage (12V typ) 30 SCL I2C Clock Input 31 SDA I2C Data Input 32 5V Pin Cushion - E/W Correction Parabola Output 9109S-01.TBL B+ PWM Regulator Output Supply Voltage (5V typ.) 3/30 TDA9109/S QUICK REFERENCE DATA Value Unit Horizontal Frequency 15 to 150 kHz Autosynch Frequency (for given R0 and C0) 1 to 4.5 f0 Horizontal Sync Polarity Input YES Polarity Detection (on both Horizontal and Vertical Sections) YES TTL Composite Sync YES Lock/Unlock Identification (on both Horizontal 1st PLL and Vertical Section) YES I2C Control for H-Position 10 XRAY Protection I2C Horizontal Duty Cycle Adjust I2C Free Running Frequency Adjustment Stand-by Function % YES 30 to 60 % 0.8 to 1.3 f0 YES Dual Polarity H-Drive Outputs NO Supply Voltage Monitoring YES PLL1 Inhibition Possibility NO Blanking Outputs NO Vertical Frequency 35 to 200 Hz Vertical Autosync (for 150nF on Pin 22 and 470nF on Pin 20) 50 to 185 Hz Vertical S-Correction YES Vertical C-Correction YES Vertical Amplitude Adjustment YES DC Breathing Control on Vertical Amplitude YES Vertical Position Adjustment YES East/West (E/W) Parabola Output (also known as Pin Cushion Output) YES E/W Correction Amplitude Adjustment YES Keystone Adjustment YES Corner Correction YES Internal Dynamic Horizontal Phase Control YES Side Pin Balance Amplitude Adjustment YES Parallelogram Adjustment YES Tracking of Geometric Corrections with Vertical Amplitude and Position YES Reference Voltage (both on Horizontal and Vertical) YES Vertical Dynamic Focus YES 2 I C Horizontal Dynamic Focus Amplitude Adjustment NO I2C Horizontal Dynamic Focus Symmetry Adjustment NO I2C Vertical Dynamic Focus Amplitude Adjustment YES Detection of Input Sync Type YES Vertical Moire Output YES Horizontal Moire Output YES 2 I C Controlled Moire Amplitude YES Frequency Generator for Burn-in YES 2 Fast I C Read/Write 400 B+ Regulation adjustable by I2C YES B+ Soft Start YES 4/30 kHz 9109S-02.TBL Parameter 2 VSYNCIN 9109S-02.EPS GND 27 SCL 30 SDA 31 5V 32 VGND 19 VREF 21 XRAY 25 VCC 29 1 H/HVIN SYNC PROCESSOR I2C INTERFACE RESET GENERATOR VREF SYNC INPUT SELECT (1 bit) PLL1F HGND 11 HLOCKOUT 6 bits 4 X Spin Bal 6 bits X2 SAFETY PROCESSOR PHASE COMPARATOR 12 HOUT BUFFER 26 B+ CONTROLLER 24 23 HMOIRE 10 FOCUS 9 17 BGND 16 ISENSE 15 REGIN 28 B+OUT 14 COMP TDA9109/S AMPVDF 6 bits HORIZONTAL MOIRE CANCEL 5 BITS+ON/OFF 18 X Keyst. 6 bits X2 E/W 7 bits X 4 Corner 7 bits B+ Adjust 7 bits H-DUTY (5 bits) VOUT BREATH 20 VPOS 7 bits VERTICAL OSCILLATOR RAMP GENERATOR VAMP 7 bits 5V VCC XRAY PHASE SHIFTER GEOMETRY TRACKING VERTICAL Parallelogram MOIRE 6 bits CANCEL 5 BITS+ON/OFF Free Running 5 bits VSYNC EWOUT VAGCCAP 22 S AND C CORRECTION 6 bits VCO Forced Frequency 2 bits LOCK/UNLOCK IDENTIFICATION PHASE/FREQUENCY COMPARATOR H-PHASE (7 bits) 5 R0 VREF C0 6 HFLY 3 PLL2C HREF 13 8 HOUT HSYNC HPOSITION 7 TDA9109/S BLOCK DIAGRAM VCAP 5/30 TDA9109/S Symbol VCC VDD VIN VESD Tstg Tj Toper Parameter Supply Voltage (Pin 29) Supply Voltage (Pin 32) Max Voltage on Pin 4 Pin 5 Pins 6, 7, 8, 14, 15, 16, 20, 22 Pins 9, 10, 18, 23, 24, 25, 26, 28 Pins 1, 2, 3, 30, 31 ESD susceptibility Human Body Model,100pF Discharge through 1.5k EIAJ Norm, 200pF Discharge through 0 Storage Temperature Junction Temperature Operating Temperature Value 13.5 5.7 4.0 6.4 8.0 VCC VDD 2 300 -40, +150 +150 0, +70 Unit V V V V V V V kV V o C o C o C 9109S-03.TBL ABSOLUTE MAXIMUM RATINGS Symbol Rth (j-a) Parameter Value Junction-Ambient Thermal Resistance Max. Unit o 65 C/W 9109S-04.TBL THERMAL DATA SYNC PROCESSOR Operating Conditions (VDD = 5V, Tamb = 25oC) Symbol HsVR MinD Mduty VsVR VSW VSmD VextM IHLOCKOUT Parameter Voltage on H/HVIN Input Minimum Horizontal Input Pulses Duration Maximum Horizontal Input Signal Duty Cycle Voltage on VSYNCIN Minimum Vertical Sync Pulse Width Maximum Vertical Sync Input Duty Cycle Maximum Vertical Sync Width on TTL H/Vcomposite Sink and Source Current Test Conditions Pin 1 Pin 1 Pin 1 Pin 2 Pin 2 Pin 2 Pin 1 Pin3 Min. 0 0.7 Typ. Max. 5 25 5 0 5 15 750 250 Unit V s % V s % s A Electrical Characteristics (VDD = 5V, Tamb = 25oC) Symbol VINTH RIN TfrOut VHlock VoutT Parameter Horizontal and Vertical Input Logic Level (Pins 1, 2) Horizontal and Vertical Pull-Up Resistor Fall and Rise Time, Output CMOS Buffer Horizontal 1st PLL Lock Output Status (Pin 3) Extracted Vsync Integration Time (% of TH) on H/V Composite (see Note 1) Test Conditions Low Level High Level Pins 1, 2 Pin 3, COUT = 20pF Locked, ILOCKOUT = -250A Unlocked, ILOCKOUT = +250A C0 = 820pF Min. Typ. Max. 0.8 2.2 200 4.4 26 0 5 35 Min. Typ. 200 0.5 Unit V V k ns V V % Note 1 : TH is the horizontal period. I2C READ/WRITE (see Note 2) Electrical Characteristics (VDD = 5V,Tamb = 25oC) Symbol Parameter Test Conditions Max. Unit 400 kHz s s V V 2 Fscl Tlow Thigh Vinth VACK Maximum Clock Frequency Low period of the SCL Clock High period of the SCL Clock SDA and SCL Input Threshold Acknowledge Output Voltage on SDA input with 3mA Note 2 : See also I2C Table Control and I2C Sub Address Control. 6/30 Pin 30 Pin 30 Pin 30 Pins 30,31 Pin 31 1.3 0.6 2.2 0.4 9109S-05.TBL I C PROCESSOR TDA9109/S HORIZONTAL SECTION Operating Conditions Symbol Parameter Test Conditions Min. Typ. Max. Unit 150 k pF kHz 5 30 mA mA VCO R0(Min.) C0(Min.) F(Max.) Minimum Oscillator Resistor Minimum Oscillator Capacitor Maximum Oscillator Frequency Pin 6 Pin 5 6 390 OUTPUT SECTION I12m HOI Maximum Input Peak Current Horizontal Drive Output Maximum Current Pin 12 Pin 26, Sunk current Electrical Characteristics (VCC = 12V, Tamb = 25oC) Symbol Parameter Test Conditions Min. Typ. Max. Unit SUPPLY AND REFERENCE VOLTAGES VCC Supply Voltage Pin 29 10.8 12 13.2 V VDD Supply Voltage Pin 32 4.5 5 5.5 V ICC Supply Current Pin 29 50 IDD Supply Current Pin 32 5 VREF-H Horizontal Reference Voltage Pin 13, I = -2mA 7.4 8 8.6 VREF-V Vertical Reference Voltage Pin 21, I = -2mA 7.4 8 8.6 V IREF-H Max. Sourced Current on VREF-H Pin 13 5 mA IREF-V Max. Sourced Current on VREF-V Pin 21 5 mA mA mA V 1st PLL SECTION Delay Time for detecting polarity change (see Note 3) Pin 1 VVCO VCO Control Voltage (Pin 7) VREF-H = 8V f0 fH(Max.) 1.3 6.2 V V Vcog VCO Gain (Pin 7) R0 = 6.49k, C0 = 820pF, dF/dV = 1/11R0C0 17.1 kHz/V Hph Horizontal Phase Adjustment (see Note 4) % of Horizontal Period 10 % Horizontal Phase Setting Value (Pin 8) (see Note 4) Minimum Value Typical Value Maximum Value Sub-Address 01 Byte x1111111 Byte x1000000 Byte x0000000 2.8 3.4 4.0 V V V PLL1 Filter Current Charge PLL1 is Unlocked PLL1 is Locked 140 1 A mA Free Running Frequency Sub-Address 02 - Byte xxx10000 R0 = 6.49k, C0 = 820pF, f0 = 0.97/8R0C0 22.8 kHz -150 ppm/C 0.8 1.3 f0 f0 Vbmin Vbtyp Vbmax IPll1U IPll1L f0 df0/dT f0(Min.) f0(Max.) CR FF 0.75 Free Running Frequency Thermal Drift (No drift on external components) (see Note 5) Free Running Frequency Adjustment Minimum Value Maximum Value Sub-Address 02 Byte xxx11111 Byte xxx00000 PLL1 Capture Range R0 = 6.49k, C0 = 820pF, from f0+0.5kHz to 4.5f0 f0 adjsusted to 22.8kHz fH(Min.) fH(Max.) Forced Frequency FF1 Byte 11xxxxxx FF2 Byte 10xxxxxx ms 23.5 100 Sub-Address 02 kHz kHz 2f0 3f0 Notes : 3. This delay is mandatory to avoid a wrong detection of polarity change in the case of a composite sync. 4. See Figure 10 for explanation of reference phase. 5. These parameters are not tested on each unit. They are measured during our internal qualification. 7/30 9109S-05.TBL HpolT TDA9109/S HORIZONTAL SECTION (continued) Electrical Characteristics (VCC = 12V, Tamb = 25oC) (continued) Symbol Parameter Test Conditions Min. Typ. Max. Unit 0.65 0.75 V 2nd PLL SECTION AND HORIZONTAL OUTPUT SECTION FBth Hjit HDmin HDmax XRAYth Flyback Input Threshold Voltage (Pin 12) Horizontal Jitter At 31.4kHz 70 ppm Horizontal Drive Output Duty-Cycle (Pin 26) (see Note 6) Sub-Address 00 Byte xxx11111 Byte xxx00000 (see Note 7) 30 60 % % X-RAY Protection Input Threshold Voltage Pin 25, see Note 8 8 V Internal Clamping Levels on 2nd PLL Loop Filter (Pin 4) Low Level High Level 1.6 4.0 V V VSCinh Threshold Voltage to Stop H-Out,V-Out, B-Out and Reset XRAY when VCC < VSCinh (see Note 8) Pin 29 7.5 V VSDinh Threshold Voltage to Stop H-Out,V-Out, B-Out and Reset XRAY when VDD < VSDinh Pin 32 4.0 V Horizontal Drive Output (low level) Pin 26, IOUT = 30mA Vphi2 HDvd 0.4 V VERTICAL DYNAMIC FOCUS FUNCTION (positive parabola) 2 V 200 ppm/C 0 0.5 1 VPP VPP VPP Parabola Amplitude Function of VAMP Sub-Address 05 (tracking between VAMP and VDF) with Byte 10000000 VPOS Typ. (see Figure 1 and Note 9) Byte 11000000 Byte 11111111 0.6 1 1.5 VPP VPP VPP VHDFKeyt Parabola Asymetry Function of VPOS Sub-Address 06 Control (tracking between VPOS and VDF) Byte x0000000 with VAMP Max. Byte x1111111 0.52 0.52 VPP VPP Bottom DC Output Level TDHDF DC Output Voltage Thermal Drift (see Note 5) AMPVDF VDFAMP Vertical Dynamic Focus Parabola Amplitude with VAMP and VPOS Typical Min. Byte 000000 Typ. Byte 100000 Max. Byte 111111 RLOAD = 10k, Pin 10 Sub-Address 0F Notes : 5. These parameters are not tested on each unit. They are measured during our internal qualification. 6. Duty Cycle is the ratio between the output transistor OFF time and the period. The power transistor is controlled OFF when the output transistor is OFF. 7. Initial Condition for Safe Operation Start Up 8. See Figure 14. 9. S and C correction are inhibited so the output sawtooth has a linear shape. 8/30 9109S-05.TBL HDFDC TDA9109/S VERTICAL SECTION Operating Conditions Symbol Parameter Test Conditions Min. Typ. Max. Unit 6.5 V OUTPUTS SECTION VEWM Maximum E/W Output Voltage Pin 24 VEWm Minimum E/W Output Voltage Pin 24 1.8 V RLOAD Minimum Load for less than 1% Vertical Amplitude Drift Pin 20 65 M Electrical Characteristics (VCC = 12V, Tamb = 25oC) Symbol Parameter Test Conditions Min. Typ. Max. Unit VERTICAL RAMP SECTION VRB Voltage at Ramp Bottom Point VREF-V = 8V, Pin 22 2 V VRT Voltage at Ramp Top Point (with Sync) VREF-V = 8V, Pin 22 5 V VRTF Voltage at Ramp Top Point (without Sync) Pin 22 VRT-0.1 V VSTD Vertical Sawtooth Discharge Time Pin 22, C22 = 150nF 70 s VFRF Vertical Free Running Frequency (see Note 10) COSC (Pin 22) = 150nF Measured on Pin22 100 Hz ASFR AUTO-SYNC Frequency (see Note 11) C22 = 150nF 5% RAFD Ramp Amplitude Drift Versus Frequency at C22 = 150nF 50Hz < f and f < 185Hz Maximum Vertical Amplitude (see Note 5) 200 ppm/Hz Ramp Linearity on Pin 22 (see Note 10) 2.5V < V27 and V27 < 4.5V 0.5 % Vertical Position Adjustment Voltage (Pin23 - VOUT mean value) Sub Address 06 Byte x0000000 Byte x1000000 Byte x1111111 3.3 3.65 3.2 3.5 3.8 V V V Vertical Output Voltage (peak-to-peak on Pin 23) Sub Address 05 Byte x0000000 Byte x1000000 Byte x1111111 2.5 3.5 2.25 3 3.75 V V V VOR VOI Vertical Output Maximum Current (Pin 23) dVS Max Vertical S-Correction Amplitude (see Note 12) x0xxxxxx inhibits S-CORR x1111111 gives max S-CORR Sub Address 07 Vertical C-Corr Amplitude x0xxxxxx inhibits C-CORR Sub Address 08 V/VPP @ TV/2 Byte x1000000 Byte x1100000 Byte x1111111 Ccorr V/VPP at TV/4 V/VPP at 3TV/4 185 Hz 5 mA -4 +4 % % -3 0 3 % % % Notes : 5. These parameters are not tested on each unit. They are measured during our internal qualification. 10. With Register 07 at Byte x0xxxxxx (S correction is inhibited) and with Register 08 at Byte x0xxxxxx (C correction is inhibited), the sawtooth has a linear shape. 11. This is the frequency range for which the vertical oscillator will automatically synchronize, using a single capacitor value on Pin 22 and with a constant ramp amplitude. 12. TV is the vertical period. 9/30 9109S-05.TBL Rlin VPOS 50 TDA9109/S VERTICAL SECTION (continued) Electrical Characteristics (VCC = 12V, Tamb = 25oC) (continued) Symbol Parameter Test Conditions Min. Typ. Max. Unit DC Output Voltage with Typ. VPOS, Keystone and Corner inhibited Pin 24, see Figure 2 2.5 V East/West (E/W) FUNCTION EWDC TDEWDC DC Output Voltage Thermal Drift See Note 13 100 ppm/C EWpara Parabola Amplitude with Max. VAMP, Typ. VPOS, Keystone and Corner inhibited Subaddress 0A Byte 11111111 Byte 11000000 Byte 10000000 1.7 0.85 0 VPP VPP VPP Parabola Amplitude Function of VAMP Control (tracking between VAMP and E/W) with Typ. VPOS, Typ. E/W Amplitude, Keystone and Corner inhibited (see Note 10) Subaddress 05 Byte 10000000 Byte 11000000 Byte 11111111 0.30 0.55 0.85 VPP VPP VPP Keystone Adjustment Capability with Typ. VPOS, Corner and E/W inhibited and Max. Vertical Amplitude (see Note 10 and Figure 4) Subaddress 09 Byte 1x000000 Byte 1x111111 0.65 0.65 VPP VPP Intrinsic Keystone Function of VPOS Control (tracking between VPOS and E/W) with Max. E/W Amplitude,Max. Vertical Amplitude and Corner inhibited (see Note 13 and Figure 2) A/B Ratio B/A Ratio Subaddress 06 Byte x0000000 Byte x1111111 0.52 0.52 Corner Amplitude with Max. VAMP, Typ. VPOS, Keystone and E/W inhibited Subaddress 0B Byte 11111111 Byte 11000000 Byte 10000000 1.7 0 -1.7 VPP VPP VPP Side Pin Balance Parabola Amplitude (Figure 3) with Max. VAMP, Typ. VPOS and Parallelogram inhibited (see Notes 10 & 14) Subaddress 0D Byte x1111111 Byte x1000000 +1.4 -1.4 %TH %TH Side Pin Balance Parabola Amplitude function of VAMP Control (tracking between VAMP and SPB) with Max. SPB, Typ. VPOS and Parallelogram inhibited (see Notes 10 & 14) Subaddress 05 Byte 10000000 Byte 11000000 Byte 11111111 0.5 0.9 1.4 %TH %TH %TH P a ra ll el o gr am A d ju st m en t C apa bilit y w ith M a x . V A M P , T y p . V P O S a n d M a x . S PB (see Notes 10 & 14) Subaddress 0E Byte x1111111 Byte x1000000 +1.4 -1.4 %TH %TH Intrinsic Parallelogram Function of VPOS Control ( trac ki ng be tween VPO S and DHPC) with Max. VAMP, Max. SPB and Parallelogram inhibited (see Notes 10 & 14) A/B Ratio B/A Ratio Subaddress 06 EWtrack KeyAdj KeyTrack Corner INTERNAL DYNAMIC HORIZONTAL PHASE CONTROL SPBpara SPBtrack ParAdj Partrack Byte x0000000 Byte x1111111 0.52 0.52 VERTICAL MOIRE VMOIRE Vertical Moire (measured on VOUT : Pin 23) Subaddress 0C Byte 01x11111 6 mV BRRANG BRADj DC Breathing Control Range (see Note 15) V18 Vertical Output Variation versus DC Breathing Control (Pin 23) V18 VREF-V V18 = 4V 1 12 0 -10 V % % Notes : 10. With Register 07 at Byte x0xxxxxx (S correction is inhibited) and with Register 08 at Byte x0xxxxxx (C correction is inhibited), the sawtooth has a linear shape. 13. These parameters are not tested on each unit. They are measured during our internal qualification. 14. TH is the horizontal period. 15. When not used the DC breathing control pin must be connected to 12V. 10/30 9109S-05.TBL BREATHING COMPENSATION TDA9109/S B+ SECTION Operating Conditions Symbol Parameter Test conditions FeedRes Minimum Feedback Resistor Resistor between Pins 15 and 14 Min. Typ. Max. Unit 5 k Electrical Characteristics (VCC = 12V, Tamb = 25oC) Parameter Test conditions Min. Typ. Max. Unit OLG Error Amplifier Open Loop Gain At low frequency (see Note 16) 85 dB ICOMP Sunk Current on Error Amplifier Output when BOUT is in safety condition Pin 14 (see Figure 14) 0.5 mA Unity Gain Bandwidth (see Note 13) 6 MHz UGBW IRI Regulation Input Bias Current Current sourced by Pin 15 (PNP base) EAOI Error Amplifier Output Current Current sourced by Pin 14 Current sunk by Pin 14 CSG Current Sense Input Voltage Gain Pin 16 MCEth ISI 0.5 2 mA mA 3 Max Current Sense Input Threshold Pin 16 Voltage Current Sense Input Bias Current A 0.2 Current sourced by Pin 16 (PNP base) 1.2 V 1 A 100 % Tonmax Maximum ON Time of the external % of Horizontal period, power transistor f0 = 27kHz (see Note 17) B+OSV B+ Output Saturation Voltage V28 with I28 = 10mA 0.25 V Internal Reference Voltage On error amp (+) input for Subaddress 0B Byte 1000000 4.8 V +20 -20 % % 100 ns IVREF VREFADJ tFB+ I n t e rn a l R e f e r e n c e Adjustment Range V ol ta g e Byte 1111111 Byte 0000000 Fall Time Pin 28 9109S-05.TBL Symbol Notes : 13. These parameters are not tested on each unit. They are measured during our internal qualification. 16. These parameters are not tested on each unit. They are measured during our internal qualification procedure which includes characterization on batches coming from corners of our processes and also temperature characterization. 17. The external power transistor is OFF during about 400ns. Figure 1 : Vertical Dynamic Focus Function B B A 9109S-03.EPS A HDFDC Figure 3 : EWPARA Dynamic Horizontal Phase Control Output 9109S-04.EPS VDFAMP Figure 2 : E/W Output EWDC Figure 4 : Keystone Effect on E/W Output (PCC and Corner Inhibited) B A DHPCDC 9109S-06.EPS SPBPARA 9109S-05.EPS Keyadj 11/30 TDA9109/S TYPICAL VERTICAL OUTPUT WAVEFORMS Function Sub Address Pin Byte Specification VOUTDC Effect on Screen 2.25V 10000000 Vertical Size 05 23 VOUTDC 3.75V 11111111 Vertical Position DC Control 06 23 VOUTDC = 3.2V VOUTDC = 3.5V VOUTDC = 3.8V x0000000 x1000000 x1111111 0xxxxxxx Inhibited Vertical S Linearity 07 D V 23 1x111111 VPP 1x000000 Vertical C Linearity 08 VPP D V D V = 3% VPP 23 D V 1x111111 VPP D V = 3% VPP 12/30 9109S-06.TBL / 9109S-07.EPS TO 9109S-13.EPS D V = 4% VPP TDA9109/S GEOMETRY OUTPUT WAVEFORMS Function Sub Address Pin Byte Specification Effect on Screen E/W+ Corner inhibited Keystone (Trapezoid) Control E/W (Pin Cushion) Control 09 1x000000 0.65V 2.5V 1x111111 0.65V 2.5V 2.5V 0V 24 Keystone + Corner inhibited 10000000 0A 24 1.7V 11111111 Keystone+ E/W inhibited 1.7V 11111111 Corner Control 0B 2.5V 24 10000000 1.7V SPB inhibited 1x000000 0E Parallelogram inhibited 3.7V 1.4% TH 3.7V 1.4% TH 1x000000 0D Internal 1x111111 Vertical Dynamic Focus 1.4% TH Internal 1x111111 Side Pin Balance Control 3.7V 0F 9109S-07.TBL / 9109S-14.EPS TO 9109S-24.EPS Parrallelogram Control 10 1.4% TH 3.7V 2V TV 13/30 TDA9109/S I2C BUS ADDRESS TABLE Slave Address (8C) : Write Mode Sub Address Definition D8 D7 D6 D5 D4 D3 D2 D1 0 0 0 0 0 0 0 0 0 Horizontal Drive Selection / Horizontal Duty Cycle 1 0 0 0 0 0 0 0 1 Horizontal Position 2 0 0 0 0 0 0 1 0 Forced Frequency / Free Running Frequency 3 0 0 0 0 0 0 1 1 Sync Priority / Horizontal Moire Amplitude 4 0 0 0 0 0 1 0 0 Refresh / B+ Reference Adjustment 5 0 0 0 0 0 1 0 1 Vertical Ramp Amplitude 6 0 0 0 0 0 1 1 0 Vertical Position Adjustment 7 0 0 0 0 0 1 1 1 S Correction 8 0 0 0 0 1 0 0 0 C Correction 9 0 0 0 0 1 0 0 1 E/W Keystone A 0 0 0 0 1 0 1 0 E/W Amplitude B 0 0 0 0 1 0 1 1 E/W Corner Adjustment C 0 0 0 0 1 1 0 0 Vertical Moire Amplitude D 0 0 0 0 1 1 0 1 Side Pin Balance E 0 0 0 0 1 1 1 0 Parallelogram F 0 0 0 0 1 1 1 1 Vertical Dynamic Focus Amplitude Slave Address (8D) : Read Mode No sub address needed. 14/30 TDA9109/S I2C BUS ADDRESS TABLE (continued) D8 D7 D6 D5 D4 D3 D2 D1 [0] [0] [0] [0] [0] [0] WRITE MODE HDrive 0, off [1], on 00 01 02 03 Xray 1, reset [0] Horizontal Duty Cycle [0] 04 05 Vramp 0, off [1], on 06 07 S Select 1, on [0] 08 C Select 1, on [0] 09 E/W Key 0, off [1] 0A [0] Horizontal Phase Adjustment [1] [0] Forced Frequency 1, on 1, f0 x 2 [0], off [0], f0 x 3 Sync HMoire 0, Comp 1, on [1], Sep [0] Detect Refresh [0], off [0] [0] [0] [0] Free Running Frequency [0] [0] [0] Horizontal Moire Amplitude [0] [0] [0] [0] [0] [0] [0] [0] B+ Reference Adjustment [1] [0] [0] [0] Vertical Ramp Amplitude Adjustment [1] [0] [0] [0] [0] [0] [0] [1] [0] Vertical Position Adjustment [0] [0] [0] S Correction [0] [0] [1] [0] [0] [0] [0] [0] [0] [0] C Correction [1] [0] [0] [0] E/W Keystone [1] [0] [0] [0] [0] [1] [0] E/W Amplitude [0] [0] [0] E/W Corner Adjustment [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] [0] 0B E/W Cor 0, off [1] [1] 0C Test V 1, on [0], off VMoire 1, on [0] 0D SPB Sel 0, off [1] 0E Parallelo 0, off [1] 0F Test H 1, on [0], off [0] [0] [0] Vertical Moire Amplitude [0] [0] [0] Side Pin Balance [1] [0] [0] [0] Parallelogram [1] [0] [1] [0] [0] [0] Vertical Dynamic Focus Amplitude [0] [0] READ MODE Hlock 0, on [1], no Vlock 0, on [1], no Xray 1, on [0], off Polarity Detection H/V pol V pol [1], negative [1], negative Vext det [0], no det Sync Detection H/V det V det [0], no det [0], no det [ ] initial value Data is transferred with vertical sawtooth retrace. We recommend to set the unspecified bit to [0] in order to assure the compatibility with future devices. 15/30 TDA9109/S OPERATING DESCRIPTION I - GENERAL CONSIDERATIONS I.1 - Power Supply The typical values of the power supply voltages VCC and VDD are 12V and 5V respectively. Optimum operation is obtained for VCC between 10.8 and 13.2V and VDD between 4.5 and 5.5V. In order to avoid erratic operation of the circuit during the transient phase of VCC and VDD switching on, or off, the value of VCC and VDD are monitored : if VCC is less than 7.5V typ. or if VDD is less than 4.0V typ., the outputs of the circuit are inhibited. Similarly, before VDD reaches 4V, all the I2C register are reset to their default value. In order to have very good power supply rejection, the circuit is internally supplied by several voltage references (typ. value : 8V). Two of these voltage references are externally accessible, one for the vertical and one for the horizontal part. They can be used to bias external circuitry (if ILOAD is less than 5mA). It is necessary to filter the voltage references by external capacitors connected to ground, in order to minimize the noise and consequently the "jitter" on vertical and horizontal output signals. I.2 - I2C Control TDA9109/S belongs to the I2C controlled device family. Instead of being controlled by DC voltages on dedicated control pins, each adjustment can be done via the I2C Interface. The I2C bus is a serial bus with a clock and a data input. The general function and the bus protocol are specified in the Philips-bus data sheets. The interface (Data and Clock) is a comparator with hysteresis ; the thresholds (less then 2.2V on rising edge, more than 0.8V on falling edge with 5V supply) are TTL-compatible. Spikes of up to 50ns are filtered by an integrator and the maximum clock speed is limited to 400kHz. The data line (SDA) can be used bidirectionally. In read-mode the IC sends reply information (1 byte) to the micro-processor. The bus protocol prescribes a full-byte transmission in all cases. The first byte after the start condition is used to transmit the IC-address (hexa 8C for write, 8D for read). 16/30 I.3 - Write Mode In write mode the second byte sent contains the subaddress of the selected function to adjust (or controls to affect) and the third byte the corresponding data byte. It is possible to send more than one data byte to the IC. If after the third byte no stop or start condition is detected, the circuit increments automatically by one the momentary subaddress in the subaddress counter (auto-increment mode). So it is possible to transmit immediately the following data bytes without sending the IC address or subaddress. This can be useful to reinitialize all the controls very quickly (flash manner). This procedure can be finished by a stop condition. The circuit has 16 adjustment capabilities : 3 for the horizontal part, 4 for the vertical, 2 for the E/W correction, 2 for the dynamic horizontal phase control,1 for the Moire option, 3 for the horizontal and the vertical dynamic focus and 1 for the B+ reference adjustment. 17 bits are also dedicated to several controls (ON/OFF, Horizontal Forced Frequency, Sync Priority, Detection Refresh and XRAY reset). I.4 - Read Mode During the read mode the second byte transmits the reply information. The reply byte contains the horizontal and vertical lock/unlock status, the XRAY activation status and, the horizontal and vertical polarity detection. It also contains the sync detection status which is used by the MCU to assign the sync priority. A stop condition always stops all the activities of the bus decoder and switches to high impedance both the data and clock line (SDA and SCL). See I2C subaddress and control tables. I.5 - Sync Processor The internal sync processor allows the TDA9109/S to accept : - separated horizontal & vertical TTL-compatible sync signal, - composite horizontal & vertical TTL-compatible sync signal. TDA9109/S OPERATING DESCRIPTION (continued) No Yes V det Comment Sync type Separated H & V Composite TTL H&V Of course, when the choice is made, we can refresh the sync detections and verify that the extracted Vsync is present and that no sync type change has occured. The sync processor also gives sync polarity information. II - HORIZONTAL PART II.1 - Internal Input Conditions A digital signal (horizontal sync pulse or TTL composite) is sent by the sync processor to the horizontal input. It may be positive or negative (see Figure 5). Using internal integration, both signals are recognized if Z/T < 25%. Synchronization occurs on the leading edge of the internal sync signal. The minimum value of Z is 0.7s. Figure 5 Z I.7 - IC status The IC can inform the MCU about the 1st horizontal PLL and vertical section status (locked or not) and about the XRAY protection (activated or not). Resetting the XRAY internal latch can be done either by decreasing the VCC or VDD supply or directly resetting it via the I2C interface. I.8 - Sync Inputs Both H/HVIN and VSYNCIN inputs are TTL compatible triggers with hysterisis to avoid erratic detection. Both inputs include a pull up resistor connected to VDD. I.9 - Sync Processor Output The sync processor indicates on the HLOCKOUT Pin whether 1st PLL is locked to an incoming horizontal sync. HLOCKOUT is a TTL compatible CMOS output. Its level goes to high when locked. In the same time the D8 bit of the status register is set to 0. This information is mainly used to trigger safety procedures (like reducing B+ value) as soon as a T 9109S-25.EPS Sync priority Subaddress 03 (D8) Yes Yes 1 Yes No 0 Vext H/V det det change is detected on the incoming sync. Further to this, it may be used in an automatic procedure for free running frequency (f0) adjustment : Sending the desired f0 on the sync input and progressively decreasing the free running frequency I2C register value (address 02), the HLOCKOUT Pin will go high as soon as the proper setting is reached. Setting the free running frequency this way allows to fully exploit the TDA9109/S horizontal frequency range. Z Another integration is able to extract the vertical pulse from composite sync if the duty cycle is higher than 25% (typically d = 35%) (see Figure 6). Figure 6 C TRAMEXT d 9109S-26.EPS I.6 - Sync Identification Status The MCU can read (address read mode : 8D) the status register via the I2C bus, and then select the sync priority depending on this status. Among other data this register indicates the presence of sync pulses on H/HVIN, VSYNCIN and (when 12V is supplied) whether a Vext has been extracted from H/HVIN. Both horizontal and vertical sync are detected even if only 5V is supplied. In order to choose the right sync priority the MCU may proceed as follows (see I2C Address Table) : - refresh the status register, - wait at least for 20ms (Max. vertical period), - read this status register. Sync priority choice should be : d The last feature performed is the removal of equalization pulses to avoid parasitic pulses on the phase comparator (which would be disturbed by missing or extraneous pulses). 17/30 TDA9109/S OPERATING DESCRIPTION (continued) II.2 - PLL1 The PLL1 consists of a phase comparator, an external filter and a voltage-controlled oscillator (VCO). The phase comparator is a "phase frequency" type designed in CMOS technology. This kind of phase detector avoids locking on wrong frequencies. It is followed by a "charge pump", composed of two current sources : sunk and sourced (typically I = 1mA when locked and I = 140A when unlocked). This difference between lock/unlock allows smooth catching of the horizontal frequency by PLL1. This effect is reinforced by an internal original slow down system when PLL1 is locked, avoiding the horizontal frequency changing too quickly. The dynamic behaviour of PLL1 is fixed by an external filter which integrates the current of the charge pump. A "CRC" filter is generally used (see Figure 7). The PLL1 is internally inhibited during extracted vertical sync (if any) to avoid taking in account missing pulses or wrong pulses on phase comparator.The inhibition is done by a switch located between the charge pump and the filter (see Figure 8). The VCO uses an external RC network. It delivers a linear sawtooth obtained by the charge and the discharge of the capacitor, with a current proportional to the current in the resistor. The typical Figure 7 PLL1F 7 1.8kW 9109S-27.EPS 1m F 4.7m F thresholds of the sawtooth are 1.6V and 6.4V. The control voltage of the VCO is between 1.33V and 6V (see Figure 9). The theorical frequency range of this VCO is in the ratio of 1 to 4.5. The effective frequency range has to be smaller (1 to 4.2) due to clamp intervention on the filter lowest value. To remove the device and external components spread, it is possible to adjust the free running frequency through I2C. This adjustment can be done automatically on the manufacturing line without manual operation by using Hlock/unlock information. The adjustment range is 0.8 to 1.3 f0 (where 1.3 f0 is the free running frequency at power on reset). Figure 8 : Block Diagram Lock/Unlock Status Tramext LOCKDET PLL1F 7 I2C Forced Frequency R0 6 C0 5 High 1 CHARGE PUMP COMP1 E2 PLL INHIBITION Low VCO HPOSITION 8 Tramext PHASE ADJUST OSC I2C HPOS Adj. 9109S-28.EPS H/HVIN INPUT INTERFACE Figure 9 : Details of VCO I2C Free Running Adjustment I0 2 a 6.4V I0 PLL1F (Loop Filter) 7 1.6V 4 I0 6.4V 5 R0 C0 1.6V 0 0.875TH TH 18/30 9109S-29.EPS (0.80 < a < 1.30) 6 (1.3V < V7 < 6V) RS FLIP FLOP TDA9109/S OPERATING DESCRIPTION (continued) The sync frequency must always be higher than the free running frequency. For example, when using a sync range between 24kHz and 100kHz, the suggested free running frequency is 23kHz. Another feature is the capability for the MCU to force the horizontal frequency through I2C to 2xf0 or 3xf0 (for burn-in mode or safety requirements). In this case, the inhibition switch is opened, leaving PLL1 free, but the voltage on PLL1 filter is forced to 2.66V (for 2xf0) or 4.0V (for 3xf0). PLL1 ensures the coincidence between the leading edge of the sync signal and a phase reference obtained by comparison between the sawtooth of the VCO and an internal DC voltage which is I2C adjustable between 2.8V and 4.0V (corresponding to 10%) (see Figure 10). II.3 - PLL2 PLL2 ensures a constant position of the shaped flyback signal in comparison with the sawtooth of the VCO, taking into account the saturation time Ts (see Figure 11). Figure 11 : PLL2 Timing Diagram H Osc Sawtooth 7/8TH 1/8TH 6.4V 4.0V 1.6V Figure 10 : PLL1 Timing Diagram Flyback 7/8TH Internally Shaped Flyback 1/8TH 6.4V 2.8V < Vb < 4.0V Vb H Drive Ts Duty Cycle 1.6V The duty cycle of H-drive is adjustable between 30% and 60%. Phase REF1 Phase REF1 is obtained by comparison between the sawtooth and a DC voltage adjustable between 2.8V and 4.0V. The PLL1 ensures the exact coincidence between the signal phase REF and HSYNC. A TH/10 phase adjustment is possible. The TDA9109/S also includes a Lock/Unlock identification block which senses in real time whether PLL1 is locked or not on the incoming horizontal sync signal. The resulting information is available on HLOCKOUT (see Sync Processor). When PLL1 is unlocked, it forces HLOCKOUT to high level. The lock/unlock information is also available through the I2C read. 9109S-30.EPS H Synchro The phase comparator of PLL2 (phase type comparator) is followed by a charge pump (typical output current : 0.5mA). The flyback input consists of an NPN transistor. This input must be current driven. The maximum recommended input current is 5mA (see Figure 12). The duty cycle is adjustable through I2C from 30% to 60%. For start-up safe operation, the initial duty cycle (after power-on reset) is 60% in order to avoid having a too long conduction period of the horizontal scanning transistor. The maximum storage time (Ts Max.) is (0.44TH TFLY/2). Typically, TFLY/TH is around 20% which means that Ts max is around 34% of TH. 19/30 9109S-31.EPS H Osc Sawtooth TDA9109/S OPERATING DESCRIPTION (continued) II.5 - X-RAY Protection The X-Ray protection is activated by application of a high level on the X-Ray input (8V on Pin 25). It inhibits the H-Drive and B+ outputs. This protection is latched ; it may be reset either by VCC or VDD switch off or by I2C (see Figure 14). Figure 12 : Flyback Input Electrical Diagram 400W HFLY 12 Q1 GND 0V 9109S-32.EPS 20kW Figure 13 VCC 26 H-DRIVE 9109S-33.EPS II.4 - Output Section The H-drive signal is sent to the output through a shaping stage which also controls the H-drive duty cycle (I2C adjustable) (see Figure 11). In order to secure the scanning power part operation, the output is inhibited in the following cases : - when VCC or VDD are too low, - when the XRAY protection is activated, - during the Horizontal flyback, - when the HDrive I2C bit control is off. The output stage consists of a NPN bipolar transistor. Only the collector is accessible (see Figure 13). This output stage is intended for "reverse" base control, where setting the output NPN in off-state will control the power scanning transistor in offstate (see Application Diagram). The maximum output current is 30mA, and the corresponding voltage drop of the output VCEsat is 0.4V Max. Obviously the power scanning transistor cannot be directly driven by the integrated circuit. An interface has to be added between the circuit and the power transistor either of bipolar or MOS type. II.6 - Vertical Dynamic Focus The TDA9109/S delivers a vertical parabola waveform on Pin 10. This vertical dynamic focus is tracked with VPOS and VAMP. Its amplitude can be adjusted. It is also affected by S and C corrections. This positive signal once amplified is to be sent to the CRT focusing grids. Figure 14 : Safety Functions Block Diagram VCC Checking I2C Drive on/off VCC VSCinh HORIZONTAL OUTPUT INHIBITION VDD Checking VDD VSDinh XRAY Protection XRAY VCC or VDD off or I C Reset 2 S R Q I2C Ramp on/off VERTICAL OUTPUT INHIBITION Horizontal Flyback BOUT 20/30 9109S-34.EPS 0.7V TDA9109/S OPERATING DESCRIPTION (continued) III - VERTICAL PART III.1 - Function When the synchronization pulse is not present, an internal current source sets the free running frequency. For an external capacitor, COSC = 150nF, the typical free running frequency is 100Hz. The typical free running frequency can be calculated by : 1 f0 (Hz) = 1.5 10-5 COSC A negative or positive TTL level pulse applied on Pin 2 (VSYNC) as well as a TTL composite sync on Pin 1 can synchronize the ramp in the range [fmin , fmax]. This frequency range depends on the ext ernal capacit or connect ed on Pin 22. A 150nF (5%) capacitor is recommended for 50Hz to 185Hz applications. The typical maximum and minimum frequency, at 25oC and without any correction (S correction or C correction), can be calculated by : f(Max.) = 3.5 x f0 and f(Min.) = 0.33 x f0 If S or C corrections are applied, these values are slighty affected. If a synchronization pulse is applied, the internal oscillator is synchonized immediately but its amplitude changes. An internal correction then adjusts it in less than half a second. The top value of the ramp (Pin 22) is sampled on the AGC capacitor (Pin 20) at each clock pulse and a transconductance amplifier modifies the charge current of the capacitor in such a way to make the amplitude again constant. The read status register provides the vertical LockUnlock and the vertical sync polarity information. We recommend the use of an AGC capacitor with low leakage current. A value lower than 100nA is mandatory. A good stability of the internal closed loop is reached by a 470nF 5% capacitor value on Pin 20 (VAGC). Figure 15 : AGC Loop Block Diagram CHARGE CURRENT TRANSCONDUCTANCE AMPLIFIER REF 22 20 VSYNCIN 2 SYNCHRO SAMPLING OSCILLATOR SAMPLING CAPACITANCE S CORRECTION VS_AMP SUB07/6bits POLARITY COR_C SUB08/6bits C CORRECTION Vlow 18 BREATH Sawth. Disch. 23 VOUT VERT_AMP SUB05/7bits VMOIRE SUB0C/5bits 9109S-35.EPS DISCH. OSC CAP VPOSITION SUB06/7bits 21/30 TDA9109/S OPERATING DESCRIPTION (continued) III.2 - I2C Control Adjustments S and C correction shapes can then be added to this ramp. These frequency independent S and C corrections are generated internally. Their amplitudes are adjustable by their respective I2C registers. They can also be inhibited by their select bits. Finally, the amplitude of this S and C corrected ramp can be adjusted by the vertical ramp amplitude control register. The adjusted ramp is available on Pin 23 (VOUT) to drive an external power stage. The gain of this stage can be adjusted (25%) depending on its register value. The mean value of this ramp is driven by its own I2C register (vertical position). Its value is VPOS = 7/16 VREF-V 300mV. Usually VOUT is sent through a resistive divider to the inverting input of the booster. Since VPOS derives from VREF-V, the bias voltage sent to the non-inverting input of the booster should also derive from VREF-V to optimize the accuracy (see Application Diagram). III.3 - Vertical Moire By using the vertical moire, VPOS can be modulated from frame to frame. This function is intended to cancel the fringes which appear when line to line interval is very close to the CRT vertical pitch. The amplitude of the modulation is controlled by register VMOIRE on sub-address 0C and can be switched-off via the control bit D7. III.4 - Basic Equations In first approximation, the amplitude of the ramp on Pin 23 (VOUT) is : VOUT - VPOS = (VOSC - VDCMID) (1 + 0.25 (VAMP)) with : - VDCMID = 7/16 VREF (middle value of the ramp on Pin 22, typically 3.5V) - VOSC = V22 (ramp with fixed amplitude) - VAMP = -1 for minimum vertical amplitude register value and +1 for maximum - VPOS is calculated by : VPOS = VDCMID + 0.3 VP with VP equals -1 for minimum vertical position register value and +1 for maximum The current available on Pin 22 is : 3 IOSC = VREF COSC f 8 with : COSC : capacitor connected on Pin 22 and f : synchronization frequency. 22/30 III.5 - Geometric Corrections The principle is represented in Figure 16. Starting from the vertical ramp, a parabola-shaped current is generated for E/W correction (also known as Pin Cushion correction), dynamic horizontal phase control correction, and vertical dynamic Focus correction. The parabola generator is made by an analog multiplier, the output current of which is equal to : I = k (VOUT - VDCMID)2 where VOUT is the vertical output ramp (typically between 2 and 5V) and VDCMID is 3.5V (for VREF-V = 8V). One more multiplier provides a current proportional to (VOUT - VDCMID)4 for corner correction. The VOUT sawtooth is typically centered on 3.5V. By changing the vertical position, the sawtooth shifts by 0.3V. In order to have good screen geometry for any end user adjustment, the TDA9109/S has the "geometry tracking" feature, which allows generation of a dissymetric parabola depending on the vertical position. Due to the large output stage voltage range (E/W, Keystone, Corner), the combination of tracking function with maximum vertical amplitude, maximum or minimum vertical position and maximum gain on the DAC control may lead to the output stage saturation. This must be avoided by limiting the output voltage with apropriate I2C registers values. For the E/W part and the dynamic horizontal phase control part, a sawtooth-shaped differential current in the following form is generated : I' = k' (VOUT - VDCMID) Then I and I' are added and converted into voltage for the E/W part. Each of the three E/W components, and the two dynamic horizontal phase controls may be inhibited by their own I2C select bit. The E/W parabola is available on Pin 24 via an emitter follower output stage which has to be biased by an external resistor (10k to ground). Since stable in temperature, the device can be DC coupled with an external circuitry. The vertical dynamic focus is available on Pin 10. The dynamic horizontal phase control drives internally the H-position, moving the HFLY position on the horizontal sawtooth in the range of 1.4% TH both for side pin balance and parallelogram. TDA9109/S OPERATING DESCRIPTION (continued) Figure 16 : Geometric Corrections Principle V.Focus Amp 2 VDCMID (3.5V) 10 Dynamic Focus 23 Vertical Ramp VOUT Parabola Generator EW+ Amp 2 Corner VDCMID (3.5V) 24 EW Output Keystone Sidepin Amp To Horizontal Phase Sidepin Balance Output Current Parallelogram III.6 - E/W EWOUT = 2.5V + K1 (VOUT - VDCMID)+ K2 (VOUT - VDCMID)2 + K3 (VOUT - VDCMID)4 K1 is adjustable by the keystone I2C register, K2 is adjustable by the E/W amplitude I2C register, K3 is adjustable by the corner I2C register. III.7 - Dynamic Horizontal Phase Control IOUT = K4 (VOUT - VDCMID)+ K5 (VOUT - VDCMID)2 K4 is adjustable by the parallelogram I2C register, K5 is adjustable by the side pin balance I2C register. 23/30 9109S-36.EPS VDCMID (3.5V) TDA9109/S OPERATING DESCRIPTION (continued) IV - DC/DC CONVERTER PART 4.8V and compared to the internal 4.8V reference (IVREF). The difference is amplified by an error amplifier, the output of which controls the power MOS switch-off current. This unit controls the switch-mode DC/DC converter. It converts a DC constant voltage into the B+ voltage (roughly proportional to the horizontal frequency) necessary for the horizontal scanning. ThisDC/DC converter must be configured in stepup mode. It operates very similarly to the well known UC3842. Main Features - Switching synchronized on the horizontal frequency, - B+ voltage always higher than the DC source, - Current limited on a pulse-by-pulse basis. The DC/DC converter is disabled : - when VCC or VDD are too low, - when X-Ray protection is latched, - directly through I2C bus. When disabled, BOUT is driven to GND by a 0.5mA current source. This feature allows to implement externally a soft start circuit. IV.1 - Step-up Mode Operating Description - The power MOS is switched-on at the middle of the horizontal flyback. - The power MOS is switched-off when its current reaches a predetermined value. For this purpose, a sense resistor is inserted in its source. The voltage on this resistor is sent to Pin16 (ISENSE). - The feedback (coming either from the EHV or from the flyback) is divided to a voltage close to Figure 17 : DC/DC Converter I2C DAC 7bits 400ns Iadjust 12V 8V 4.8V 20% 95dB A BOUT S 1/3 C2 28 S Q Inhibit SMPS R 1.2V Soft Start C3 1.2V Inhibit SMPS REGIN COMP 15 14 ISENSE TDA9109/S 16 1MW L 22kW VB+ 24/30 9109S-37.EPS + TDA9109/S INTERNAL SCHEMATICS Figure 18 Figure 19 5V HLOCKOUT 9109S-38.EPS 3 Figure 20 9109S-39.EPS 200W Pins 1 -2 H/HVIN VSYNCIN 20kW 5V Figure 21 12V 12V HREF 13 PLL2C HREF 13 4 5 Figure 22 9109S-41.EPS 9109S-40.EPS C0 Figure 23 HREF HREF 13 13 12V PLL1F 7 9109S-43.EPS 9109S-42.EPS R0 6 25/30 TDA9109/S INTERNAL SCHEMATICS (continued) Figure 24 Figure 25 HREF 5V 12V 12V HPOSITION 8 Figure 26 9109S-45.EPS 9109S-44.EPS HMOIRE 9 Figure 27 12V HREF 13 12V 12V FOCUSOUT 10 Figure 28 9109S-47.EPS 9109S-46.EPS HFLY 12 Figure 29 12V REGIN 15 26/30 9109S-49.EPS 9109S-48.EPS COMP 14 TDA9109/S INTERNAL SCHEMATICS (continued) Figure 30 Figure 31 12V 12V ISENSE 16 Figure 32 9109S-51.EPS 9109S-50.EPS BREATH 18 Figure 33 12V VCAP 22 12V 9109S-52.EPS 9109S-53.EPS VAGCCAP 20 Figure 34 Figure 35 12V 12V EWOUT 24 9109S-54.EPS 9109S-55.EPS VOUT 23 27/30 TDA9109/S INTERNAL SCHEMATICS (continued) Figure 36 Figure 37 12V 12V HOUT-BOUT Pins 26-28 Figure 38 12V 9109S-58.EPS Pins 30-31 SDA - SCL 28/30 9109S-57.EPS 9109S-56.EPS XRAY 25 TDA9109/S APPLICATION DIAGRAMS Figure 39 : Demonstration Board J16 J15 J14 +12V TP1 CC2 10m F +5V L1 22m H TP13 J11 PC1 47kW 1 H/HVIN R39 4.7kW R29 4.7kW R42 100W +5V 32 C30 100m F TP16 R41 100W C32 100nF C40 22pF SCL TP17 J12 R53 1kW HOUT 7 6 4 C43 47m F C37 33pF 3 2 1 R15 1kW R34 1kW R45 33kW +5V TILT J13 C42 1m F +5V R30 10kW E/W POWER STAGE R37 27kW TP14 R49 22kW R43 10kW +12V C36 1m F R7 10kW EWOUT 24 5 L2 22m H D2 1N4148 C17 1m F 9 HMOIRE 8 C38 33pF C49 100nF 2kW 9 8MHz R56 560W C48 10m F 8 HPOSITION XRAYIN 25 R8 10kW 10 PWM0 HOUTCOL 26 11 IC3 - STV9422 +12V 7 PLL1F PWM7 J8 GGND 27 C13 10nF C31 4.7m F R36 1.8kW HOUT C22 33pF 6 R0 12 X1 R23 6.49kW 1% C25 33pF R35 10kW +12V B+OUT 28 FBLK R10 10kW 5 C0 PWM1 +12V +12V C5 100m F C6 100nF PWM6 CC4 47pF PC2 47kW VCC 29 VSYNC 4 PLL2C C28 820pF 5% TEST QA GND 8 B QB 7 VDD QB IA QA 6 HSYNC IB IA 5 24 G IB 4 23 PXCK CDB TA2 CDA 3 22 R TB2 TA1 2 SCL 30 C7 22nF 21 CKOUT VCC TB1 1 3 HLOCKOUT 2W 20 GND 9 19 XTALOUT 10 18 RST 11 17 SDA 12 16 PWM2 13 15 XTALIN 14 14 PWM3 15 ICC1 MC14528 16 13 SCL TP10 PWM5 SDA +12V CC1 100nF C45 10m F SDA 31 2 VSYNCIN PWM4 CC3 47pF 4 3 2 1 C39 22pF +5V IC4 TDA9109/S R17 270kW R31 27kW HFLY R38 2.2W 3W R19 270kW Q1 Q2 BC557 BC557 J1 C11 220pF E/W R25 1kW J9 10 FOCUS DYN FOCUS R24 10kW VOUT 23 R9 470W +12V L4 47m H R33 4.7kW R18 39kW Q3 TIP122 C12 11 HGND VCAP 22 R52 3.9kW 150nF C16 ( *) 12 HFLY J19 1 C27 47m F 2 C33 100nF VREF 21 C3 47m F HREF 13 HREF VAGCCAP 20 470nF 3 4 JP1 14 COMP C4 100nF C2 100nF R50 1MW 7 R40 36kW 15 REGIN REGIN R51 1kW 16 ISENSE C41 470pF BGND 17 J3 TP4 TP3 TP7 6 J6 3 5 1 4 R1 12kW BREATH 18 R57 82kW ISENSE IC1 TDA8172 J2 +12V -12V C10 100m F 35V 2 VGND 19 C46 1nF C9 100nF TP6 R2 5.6kW CON4 C51 100nF C14 470m F D1 1n4001 C15 C10 -12V 470m F C47 100pF 1 C1 220nF C8 100nF R3 1.5W R5 5.6kW R11 220W 0.5W V YOKE 2 3 J18 R4 1W 0.5W VERTICAL DEFLECTION STAGE GND R58 10W Q4 BC557 J17 B+OUT TP8 EHT COMP R75 10kW R76 47kW P1 10kW R77 15kW HOUT Q5 BC547 R74 10kW R73 1MW C60 100nF L3 22m H C50 10m F 9109S-59.EPS +12V ( *) Optional The difference with standard TDA9109 Application Diagram is the resistor divider 2k/2 on Pin 9 (HMOIRE). 29/30 TDA9109/S PMSDIP32.EPS PACKAGE MECHANICAL DATA 32 PINS - PLASTIC SHRINK DIP A A1 A2 B B1 C D E E1 e eA eB L Min. 3.556 0.508 3.048 0.356 0.762 0.203 27.43 9.906 7.620 2.540 Millimeters Typ. 3.759 3.556 0.457 1.016 0.254 27.94 10.41 8.890 1.778 10.16 3.048 Max. 5.080 4.572 0.584 1.397 0.356 28.45 11.05 9.398 Min. 0.140 0.020 0.120 0.014 0.030 0.008 1.080 0.390 0.300 12.70 3.810 0.100 Inches Typ. 0.148 0.140 0.018 0.040 0.010 1.100 0.410 0.350 0.070 0.400 0.120 Max. 0.200 0.180 0.023 0.055 0.014 1.120 0.435 0.370 0.500 0.150 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No licence is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics (c) 1998 STMicroelectronics - All Rights Reserved Purchase of I2C Components of STMicroelectronics, conveys a license under the Philips I2C Patent. Rights to use these components in a I2C system, is granted provided that the system conforms to the I2C Standard Specifications as defined by Philips. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Morocco- The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 30/30 SDIP32.TBL Dimensions