tyco CHAMP Interconnection System ANP Flectronics CHAMP Latch Low Profile ConnectorsStandard (Continued) Cover Panel Mount Plug E75) Assembly (1. a * Terminating Side -820 {20.83} (Assembled) 192 ,. (4.88) D2. (2 Holes) Panel Mount Receptacle Assembly 820 [20.83] (Assembled) -192 [4.88] Dia. (2 Holes) -192 [4.88] 20 = 2. a _ = = 9) x oa oa So = oo oO = = f] o - So = na <= a = wo 3 nan o = > = a] oO co ol oo @ 3 _ @ = = rs) Part Numbers Dimensions No. of Bail Lock Screw Lock Screw Lock Panel Mount Panel Mount Positions _ AR Plug Plug Receptacle Plug Receptacle Assembly Assembly Assembly Assembly Assembly 1.750 1.416 14 44.45 35.97 _ 553596-1 53597-1 _ _ 2.175 1.842 24 55.25 46.79 _ 553598-1 553599-1 554103-1 554088-1 2.685 2.352 36 68.20 59.74 554084-1 553600-1 553601-1 _ 554089-1 3.280 2.946 50 83.31 74.83 554085-1 553602-1 553603-1 _ 554090-1 Recommended Panel Cutout CHAMP Latch Cable B te Strain Relief Clip D Ref. $I \ The CHAMP Latch Cable Strain Relief Clip, 50- 90 Pull Cate 7 C Dia. (2 Holes) E Min. A toe [78:36] No. of Front Panel Mount! Rear Panel Mount2 Pos. A B c oD EE A B c oD EE 14 1.063 1.416 .126 .320 .640 1.151 1.416 .149 .310 .620 27.00 35.97 3.20 8.13 16.26 29.24 35.97 3.78 7.87 15.75 o4 1,488 1.842 .126 .320 640 1.575 1.842 .1493 .310 .620 37.80 46.79 3.20 8.13 16.26 40.01 46.79 3.78 7.87 15.75 36 2.000 2.352 .126 .320 640 2.085 2.352 .149 .310 .620 50.80 59.74 3.20 8.13 16.26 52.96 59.74 3.78 7.87 15.75 50 2-700 2.946 .126 .320 640 2.700 2.946 .149 .310 .620 68.58 74.83 3.20 8.13 16.26 68.58 74.83 3.78 7.87 15.75 Front Panel Mount Panel Thickness Range: .062-.125 [1.57-3.18]. Rear Panel Mount Panel Thickness Range: .062 [1.57] Max. Standard Hardware.062-.093 [1.57-2.36] Metric Hardware. 1 For front panel mount application, install from the front of the panel to avoid excessive bending of the cable. Bending of the cable will occur if cable assembly is mounted from the rear of the panel. 2 Screw Lock version only. 3 For IEEE-488 applications, refer to preassembled shielded panel cutouts page 110. position, is used only with a Low Profile Standard CHAMP Latch Connector. The Strain Relief Clip snaps on the connector and over the cable. The clip provides a positive strain relief for cable in axial and 90 directions. Material Stainless steel wire, .050 [.127] diameter Axial Pull ~ Strain Relief End View s 645 i | (16.33) 5! 117.63] CHAMP Latch Cable Strain Relief Clip Part Number 554099-1 105 Catalog 1-1773441-4 Issued 10-05 Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. www.tycoelectronics.com to change. Dimensions are shown for reference purposes only. Specifications subject USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967