SM72441 www.ti.com SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 SM72441 Programmable Maximum Power Point Tracking Controller for Photovoltaic Solar Panels Check for Samples: SM72441 FEATURES DESCRIPTION * * * The SM72441 is a programmable MPPT controller capable of controlling four PWM gate drive signals for a 4-switch buck-boost converter. Along with SM72295 (Photovoltaic Full Bridge Driver) it creates a solution for an MPPT configured DC-DC converter with efficiencies up to 98.5%. Integrated into the chip is an 8-channel, 12 bit A/D converter used to sense input and output voltage and current, as well as board configuration. Externally programmable values include maximum output voltage and current as well as different settings on slew rate, and soft-start. 1 2 * * * Renewable Energy Grade Programmable Maximum Power Point Tracking Photovoltaic Solar Panel Voltage and Current Diagnostic Single Inductor Four Switch Buck-boost Converter Control VOUT Overvoltage Protection Over-Current Protection PACKAGE * TSSOP-28 Block Diagram VDDA AVin AIN0 AIin AIN1 AVout AIN2 VDDD D0 D1 D2 CS_N SCLK AIout AIN3 DIN ADC DOUT A0 AIN4 A2 AIN5 A4 AIN6 A6 AIN7 D3 D4 D5 D6 D7 Vin Iin Vout Iout MPPT CONTROLLER HIA LIA ADC CONTROLLER ADC_C VSSA HIB LIB CLK GEN VSSD Figure 1. Block Diagram 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2010-2013, Texas Instruments Incorporated SM72441 SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 PV(+) www.ti.com Vo Rsen_in Gate 2 Current Sensing Amplifier Gate 4 Vo R PV(-) 5V 0.01 PF R 0.01 PF Rsen_out 0.01 PF Gate 3 Gate 1 49.9: 2.2 PF 2.2 PF 5V VDDD VDDA AVIN AIIN Current Sensing Amplifier AIOUT Current Sensing Amplifier Current sensing Amplifier RT1 RT2 RT3 NC7 RT4 NC1 .1 PF 0.1 PF 0.1 PF A0 A2 A4 A6 0.1 PF RB2 RB3 10k RB4 10k 10k CONFIGURATION RESISTOR 10k 10k 10k NC2 PWM1 SM72441 Gate 1 150k NC6 RST 10k NC3 10k OVP RFB1 AVOUT LED VSSA Gate 2 H-Bridge Driver 5V NC9 NC8 Gate 3 PWM2 HIA NC5 NC4 Gate 4 PWM3 LIB LIA 5V RB1 PWM4 HIB RFB2 VSSD Figure 2. Typical Application Circuit 2 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 SM72441 www.ti.com SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 Connection Diagram Top View 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 RST OVP NC1 LIA VDDD HIA 26 VSSD HIB 25 NC2 LIB 24 NC3 NC9 23 NC8 22 NC5 AIOUT 21 NC6 A6 20 NC7 AIIN 19 LED A4 18 VDDA AVOUT 17 VSSA A2 16 AVIN 15 NC4 SM72441 A0 27 Figure 3. TSSOP-28 Package See Package Drawing PW0028A Pin Descriptions Pin Name 1 RST Active low signal. External reset input signal to the digital circuit. 2 NC1 No Connect. This pin should be grounded. 3 VDDD Digital supply voltage. This pin should be connected to a 5V supply, and bypassed to VSSD with a 0.1uF monolithic ceramic capacitor. 4 VSSD Digital ground. The ground return for the digital supply and signals. 5 NC2 No Connect. This pin should be pulled up to the 5V supply using 10k resistor. 6 NC3 No Connect. This pin should be grounded using a 10k resistor. 7 NC4 No Connect. This pin should be grounded using a 10k resistor. 8 NC5 No Connect. This pin should be pulled up to 5V supply using 10k resistor. 9 NC6 No Connect. This pin should be pulled up to 5V supply using 10k resistor. 10 NC7 No Connect. This pin should be grounded. 11 LED LED pin outputs a pulse during normal operation. 12 VDDA Analog supply voltage. This voltage is also used as the reference voltage. This pin should be connected to a 5V supply, and bypassed to VSSA with a 1uF and 0.1uF monolithic ceramic capacitor. 13 VSSA Analog ground. The ground return for the analog supply and signals. 14 A0 15 AVIN 16 A2 17 Description A/D Input Channel 0. Connect a resistor divider to 5V supply to set the maximum output voltage. Please refer to application section for more information on setting the resistor value. A/D Input to sense input voltage. A/D Input Channel 2. Connect a resistor divider to 5V supply to set MPPT update rate. Please refer to application section for more information on setting the resistor value. AVOUT A/D Input to sense the output voltage. 18 A4 19 AIIN 20 A6 21 AIOUT A/D Input Channel 4. Connect a resistor divider to 5V supply to set the maximum output current. Please refer to application section for more information on setting the resistor value. A/D Input to sense input current. A/D Input Channel 6. Connect a resistor divider to 5V supply to set the maximum output voltage slew rate. Please refer to application section for more information on setting the resistor value. A/D Input to sense the output current. Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 3 SM72441 SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 www.ti.com Pin Descriptions (continued) Pin Name 22 NC8 No Connect. This pin should be grounded using a 10k resistor. Description 23 NC9 No Connect. This pin should be connected with 150k pull-up resistor to 5V supply. 24 LIB Low side boost PWM output. 25 HIB High side boost PWM output. 26 HIA High side buck PWM output. 27 LIA Low side buck PWM output. 28 OVP Overvoltage Protection Pin. Active Low. SM72441 will reset once voltage on this pin drops below its threshold voltage. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Analog Supply Voltage VA (VDDA -VSSA) -0.3 to 6.0V Analog Supply Voltage VD (VDDD -VSSD) -0.3 to VA +0.3V, max 6.0V Voltage on Any Pin to GND -0.3 to VA +0.3V Input Current at Any Pin (Note 3) 10 mA Package Input Current (Note 3) 20 mA Storage Temperature Range ESD Rating (3) (1) (2) (3) -65C to +150C Human Body Model 2 kV Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is ensured. Operating Ratings indicate conditions for which the device is intended to be functional, but does not ensure specific performance limits. For specified performance limits and associated test conditions, see the Electrical Characteristics tables. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Recommended Operating Conditions Operating Temperature -40C to 105C VA Supply Voltage +4.75V to +5.25V VD Supply Voltage +4.75V to VA Digital Input Voltage 0 to VA Analog Input Voltage 0 to VA Junction Temperature 4 -40C to 125C Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 SM72441 www.ti.com SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 Electrical Characteristics Specifications in standard typeface are for TJ = 25C, and those in boldface type apply over the full operating junction temperature range. (1) Symbol Parameter Conditions Min Typ Max Units - 0 to VA - V ANALOG INPUT CHARACTERISTICS AVin, AIin AVout, AIout Input Range IDCL DC Leakage Current CINA Input Capacitance (2) VERR DC Voltage Measurement Accuracy - - 1 A Track Mode - 33 - pF Hold Mode - 3 - pF 0.1 % DIGITAL INPUT CHARACTERISTICS VIL Input Low Voltage - - 0.8 VIH Input High Voltage 2.8 - - V V CIND Digital Input Capacitance (2) - 2 4 pF IIN Input Current - 0.01 1 A VD-0.5 - - V - - 0.4 V 1 A 2 4 pF 4.75 5 5.25 V 7 10 15 mA 50 78 mW DIGITAL OUTPUT CHARACTERISTICS VOH Output High Voltage ISOURCE = 200 A VA = VD = 5V VOL Output Low Voltage ISINK = 200 A to 1.0 mA VA = VD = 5V IOZH , IOZL Hi-Impedance Output Leakage Current VA = VD = 5V COUT Hi-Impedance Output Capacitance (2) POWER SUPPLY CHARACTERISTICS (CL = 10 pF) VA ,VD Analog and Digital Supply Voltages VA VD IA + ID Total Supply Current VA = VD = 4.75V to 5.25V PC Power Consumption VA = VD = 4.75V to 5.25V PWM OUTPUT CHARACTERISTICS fPWM PWM switching frequency 210 kHz tDEAD Dead time 38 ns (1) (2) Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate Texas Instrument's Average Outgoing Quality Level (AOQL). Not tested. Specified by design. Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 5 SM72441 SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 www.ti.com OPERATION DESCRIPTION OVERVIEW The SM72441 is a programmable MPPT controller capable of outputting four PWM gate drive signals for a 4switch buck-boost converter. Refer to the Typical Application Circuit diagram (Figure 2). The SM72441 uses an advanced digital controller to generate its PWM signals. A maximum power point tracking (MPPT) algorithm monitors the input current and voltage and controls the PWM duty cycle to maximize energy harvested from the photovoltaic module. MPPT performance is very fast. Convergence to the maximum power point of the module typically occurs within 0.01s. This enables the controller to maintain optimum performance under fast-changing irradiance conditions. Transitions between buck, boost, and buck-boost modes are smoothed, and advanced digital PWM dithering techniques are employed to increase effective PWM resolution. Output voltage and current limiting functionality are integrated into the digital control logic. The controller is capable of handling both shorted and no-load conditions and will recover smoothly from both. RESET SOFT-START RST Pin is low or Iout < Iout_th OVP Pin is low Buck Boost Iout >= Iout_th Iout >= Iout_th Iout < Iout_th MPPT Figure 4. High Level State Diagram for Startup STARTUP SM72441 has a soft start feature that will ramp its output voltage for a fixed time of 250ms. MPPT mode will be entered during soft start if the load current exceeded the minimum current threshold. Otherwise, buck-boost operation is entered after soft-start is finished where the ratio between input and output voltage is 1:1. Refer to Figure 4 for a high level state diagram of startup. The current threshold to transition between MPPT to standby (buck-boost) mode and vice versa can be set by feeding the output of current sensing amplifier (Figure 2) to the AIIN and AIOUT pin. For an appropriate voltage level, refer to the AIIN AND AIOUT PIN section of this datasheet. 6 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 SM72441 www.ti.com SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 Figure 5. Start-Up Waveforms of Controlled Output MAXIMUM OUTPUT VOLTAGE Maximum output voltage on the SM72441 is set by resistor divider ratio on pin A0. (Please refer to Figure 2 Typical Application Circuit). VOUT_MAX = 5 x (RFB1 + RFB2) RB1 x RFB2 RT1 + RB1 (1) Where RT1 and RB1 are the resistor divider on the ADC pin A0 and RFB1 and RFB2 are the output voltage feedback resistors. A typical value for RFB2 is about 2 k. CURRENT LIMIT SETTING Maximum output current can be set by changing the resistor divider on A4 (pin 18). (Refer to Figure 2 ). Overcurrent at the output is detected when the voltage on AIOUT (pin 21) equals to the voltage on A4 (pin 18). The voltage on A4 can be set by a resistor divider connected to 5V whereas a current sense amplifier output can be used to set the voltage on AIOUT. AIIN AND AIOUT PIN These two pins are used to set current threshold from standby (buck-boost mode) to MPPT mode and from MPPT mode into standby mode. In order to transition from standby to MPPT mode, the following conditions have to be satisfied: 1) AIIN and AIOUT voltage > 0.488V 2) Iout < Iout_max On the other hand, in order to transition from MPPT to standby mode, the following condition have to be satisfied: 1) AIIN and AIOUT voltage < 0.293V 2) Iout < Iout_max Current limit is triggered when AIOUT (pin 21) voltage is equal to A4 (pin 18). AVIN PIN AVIN pin is an A/D input to sense the input voltage of SM72441. A resistor divider can be used to scale the max voltage to about 4V, which is 80% of the full scale of the A/D input. Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 7 SM72441 SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 www.ti.com CONFIGURABLE SETTINGS The voltage on A0 sets the max output voltage; whereas the voltage on A2 enables MPPT update rate and limits the max boost ratio when output current is below the standby threshold. Output current limit is set by the voltage on A4 and output voltage slew rate limit is set on A6. In order to set a slew rate limit of 125V/sec, the ratio of the two resistors in A6 should be 9:1. The low current condition is detected if the voltage on AIIN is less than 0.488V (rising) and 0.293 (falling) + I or if the voltage on AIOUT is less than 0.488 V (rising) and 0.293 (falling) + I. If low current is detected, the converter operates in standby mode and limit the maximum duty cycle to either a 1 (buck-boost), 1.15 (boost) or 1.25 (boost) conversion ratio (programmable). In this case no MPPT will be performed. The actual value of current will depend on the gain of the current sensing amplifier circuitry that feeds the AIIN and AIOUT pins. For more complete information on the various settings based on the voltage level of A2, please refer to Table 1 below. Vfs denotes the full scale voltage of the ADC which is equal to VDDA where VDDA is a reference voltage to analog ground. A typical value for top configuration resistors (RT1 to RT4) should be 20 k. Table 1. List of Configurable Modes on ADC Channel 2 8 ADC Channel 2 MPPT Update Time Slew Rate Detection Low Current Detection Initial Boost Ratio Delta I 0 < VADC2 < Vfs/16 1.2 ms Disabled Disabled N/A N/A 1Vfs/16 < VADC2 <2Vfs/16 38 ms Disabled Disabled N/A N/A 2Vfs/16 < VADC2 <3Vfs/16 77 ms Disabled Disabled N/A N/A 3Vfs/16 < VADC2 <4Vfs/16 38 ms Enabled Disabled N/A N/A 4Vfs/16 < VADC2 <5Vfs/16 38 ms Enabled Enabled 1.15 60 (0.3 A) 5Vfs/16 < VADC2 <6Vfs/16 38 ms Enabled Enabled 1.15 90 (0.45 A) 6Vfs/16 < VADC2 <7Vfs/16 38 ms Enabled Enabled 1.15 120(0.6 A) 7Vfs/16 < VADC2 <8Vfs/16 38 ms Enabled Enabled 1.25 60 8Vfs/16 < VADC2 <9Vfs/16 38 ms Enabled Enabled 1.25 90 9Vfs/16 < VADC2 <10Vfs/16 38 ms Enabled Enabled 1.25 120 10Vfs/16 < VADC2 <11Vfs/16 77 ms Enabled Enabled 1.15 60 11Vfs/16 < VADC2 <12Vfs/16 77 ms Enabled Enabled 1.15 90 12Vfs/16 < VADC2 <13Vfs/16 77 ms Enabled Enabled 1.15 120 13Vfs/16 < VADC2 <14Vfs/16 77 ms Enabled Enabled 1.25 60 14Vfs/16 < VADC2 <15Vfs/16 77 ms Enabled Enabled 1.25 90 15Vfs/16 < VADC2 <16Vfs/16 77 ms Enabled Enabled 1.25 120 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 SM72441 www.ti.com SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 RESET PIN When the reset pin is pulled low, the chip will cease its normal operation and turn-off all of its PWM outputs. Below is an oscilloscope capture of a forced reset condition. Figure 6. Reset Operational Behavior As seen in Figure 6, the initial value for output voltage and load current are 28V and 1A respectively. After the reset pin is grounded, both the output voltage and load current decreases immediately. MOSFET switching on the buck-boost converter also stops immediately. VLOB indicates the low side boost output from the SM72295. ANALOG INPUT An equivalent circuit for one of the ADC input channels is shown in Figure 7. Diode D1 and D2 provide ESD protection for the analog inputs. The operating range for the analog inputs is 0V to VA. Going beyond this range will cause the ESD diodes to conduct and result in erratic operation. The capacitor C1 in Figure 7 has a typical value of 3 pF and is mainly the package pin capacitance. Resistor R1 is the on resistance of the multiplexer and track / hold switch; it is typically 500. Capacitor C2 is the ADC sampling capacitor; it is typically 30 pF. The ADC will deliver best performance when driven by a low-impedance source (less than 100). This is especially important when sampling dynamic signals. Also important when sampling dynamic signals is a band-pass or low-pass filter which reduces harmonic and noise in the input. These filters are often referred to as anti-aliasing filters. VA D1 R1 C2 VIN C1 3 pF 30 pF D2 Conversion Phase: Switch Open Track Phase: Switch Close Figure 7. Equivalent Input Circuit DIGITAL INPUTS AND OUTPUTS The digital input signals have an operating range of 0V to VA, where VA = VDDA - VSSA. They are not prone to latch-up and may be asserted before the digital supply VD, where VD = VDDD - VSSD, without any risk. The digital output signals operating range is controlled by VD. The output high voltage is VD - 0.5V (min) while the output low voltage is 0.4V (max). Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 9 SM72441 SNOSB64G - OCTOBER 2010 - REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision F (April 2013) to Revision G * 10 Page Changed layout of National Data Sheet to TI format ............................................................................................................ 9 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: SM72441 PACKAGE OPTION ADDENDUM www.ti.com 2-Nov-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) SM72441MT/NOPB ACTIVE TSSOP PW 28 48 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 105 S72441 SM72441MTE/NOPB ACTIVE TSSOP PW 28 250 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 105 S72441 SM72441MTX/NOPB ACTIVE TSSOP PW 28 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 105 S72441 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 2-Nov-2017 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SM72441MTE/NOPB TSSOP PW 28 250 178.0 16.4 6.8 10.2 1.6 8.0 16.0 Q1 SM72441MTX/NOPB TSSOP PW 28 2500 330.0 16.4 6.8 10.2 1.6 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SM72441MTE/NOPB TSSOP PW SM72441MTX/NOPB TSSOP PW 28 250 210.0 185.0 35.0 28 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: SM72441MTE/NOPB SM72441MT/NOPB SM72441MTX/NOPB