LCP-8500B4QDRx RoHS Compliant 8.5Gb/s Long Wavelength SFP+ Transceiver for Fiber Channel FEATURES Compliant with SFP transceiver SFF-8472 MSA specification and Fiber Channel FC-PI-4 1310nm DFB LD Transceiver Built-in digital diagnostic monitoring function Compliant with Industry Standard RFT Electrical Connector and Cage Duplex LC connector Laser Class 1 Product which comply with the requirements of IEC 60825-1 and IEC 60825-2 Description Applications The LCP-8500B4QDRx series are hot pluggable 3.3V Small-Form-Factor transceiver modules designed expressly for high-speed communication applications that require rates of up to 8.5Gb/s. It is compliant with the Fiber Channel standards FC-PI-4, as well as MSA SFF-8472. 8.5 GBd Fiber Channel operation for FC-PI-4 800-SM-LC-L Performance LCP-8500B4QDRx Series Data Link up to 10km in 9/125m Single Mode Fiber The LCP-8500B4QDRx transceivers provide with the LC receptacle that is compatible with TM connector. The the industry standard LC transceiver is also compatible with industry standard RFT connector and cage. The post-amplifier of the LCP-8500B4QDRx also includes a LOS (Loss Of Signal) circuit that provides a TTL logic-high output when an unusable optical signal level is detected. The LCP-8500B4QDRx transceiver is a Class 1 eye safety product. The optical power levels, under normal operation, are at eye safe level. 1 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Range @3.3V Symbol TS VCC3 Min. -40 -0.5 Typ. Max. 85 3.6 Unit V Note Min. -5 3.135 5 0 Typ. Max. +70 3.465 85 3.6 Unit V % V Note 1 Unit mA W V V V V V V Note Recommended Operating Conditions Parameter Case Operating Temperature Supply Voltage @3.3V Relative Humidity (non condensation) DC Common Mode Voltage Symbol TC VCC3 VCM 3.30 Notes: 1. See ordering information Low Speed Electrical Characteristics (VCC=3.135V to 3.465V) Parameter Total Supply Current Power Consumption TX_Fault, RX_LOS TX_Disable RS0, RS1 Symbol ICC PC VOL VOH VIL VIH VIL VIH Min. Typ. 0 Host_Vcc-0.5 -0.3 2.0 -0.3 2.0 1. Shall be pulled up with 4.7k-10k ohms to 3.3 volt in the module. 2. Shall be pulled low to GND with a 30k ohms resistor in the module. 2 DELTA ELECTRONICS, INC. Max. 300 1 0.4 Host_Vcc+0.3 0.8 VccT+0.3 0.8 VccT+0.3 1 1 2 2 Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Optical Transmitter Characteristics Parameter Symbol Signaling speed R (nominal) Signaling speed variation from nominal Center Wavelength Side Mode Suppression SMSR Ratio Optical Modulaion OMA Amplitude Average output power AP Optical Rise/Fall Time tr,tf (20%-80%) Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} Min Typ. Max 8.5 1260 Units Gb/s 100 ppm 1355 nm 30 dB 290 uW -8.4 Notes +0.5 dBm 50 ps {0.25, 0.40, 0.45, 0.32, 0.35, 0.40} Notes: 1. Even if the TDP < 1 dB, the OMA (min) must exceed this value. Transmitter eye mask definition 3 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx 4. Optical Receive Characteristics Parameter Symbol Signaling speed (nominal) Signaling speed variation from nominal Center Wavelength Overload Receiver sensitivity in OMA LOS De-assert LOS Assert Ts PO Min Typ 8.5 1260 RSO LOSD LOSA Max -30 Units Notes Gb/s 100 ppm 1355 +0.5 nm dBm 42 uW -18 dBm dBm [1] Notes: -12 1. Value in OMA measured with 2^7-1 PRBS for BER = 10 . SFP+ Transceiver Electrical Pad Layout 4 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Module Electrical Pin Definition Pin Logic 1 Symbol VeeT Name/Description Module Transmitter Ground 1 Module Transmitter Fault 2 Transmitter Disable; Turns off transmitter laser output 3 2 LVTTL-O TX_Fault 3 LVTTL-I TX_Disable 4 LVTTL-I/O SDA 2- write Serial Interface Data Line 5 LVTTL-I/O SCL 2- write Serial Interface Clock 6 MOD_ABS Note Module Absent, connected to VeeT or VeeR in the module 4 7 LVTTL-I RS0 8 LVTTL-O RX_LOS 9 LVTTL-I RS1 Not Implement VeeR Module Receiver Ground 1 Module Receiver Ground 1 10 11 VeeR Not Implement Receiver Loss of Signal Indication 12 CML-O RD- Receiver Inverted Data Output 13 CML-O RD+ Receiver Non-Inverter Data Output 14 VeeR Module Receiver Ground 15 VccR Module Receiver 3.3V Supply 16 VccT Module Transmitter 3.3V Supply 17 VeeT Module Transmitter Ground 18 CML-I TD+ Transmitter Non-Inverted Data Input 19 CML-I TD- Transmitter Inverted Data Input 20 VeeT 2 1 1 Module Transmitter Griund 1 Note: 1. The module signal ground pins, VeeR and VeeT, shall be isolated from the module case. 2. This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10k ohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5V. 3. This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10k ohms to VccT in the Module. 4. This pin shall be pulled up with 4.7k-10k ohms to Host_Vcc on the host board. 5 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Low speed electrical control pins and 2-wire interface In addition to the 2-wire serial interface, the SFP+ module has the following low speed pins for control and status: TX_Fault TX_Disable RS0/RS1 MOD_ABS RX_LOS 1 TX_Fault .TX_Fault is a module output pin that when High, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output pin is an open drain/collector and must be pulled p to the Host_Vcc with 4.7k-10k ohms on the host board 2 TX_Disable TX_Disable is a module input pin. When TX_Disable is asserted High or Left open, the SFP+ module transmitter output must be turned off. The TX_DIS pin must be pulled up to VccT in the SFP+ module.. 3 RS0/RS1 RS0 and RS1 are module input rate select pins and are pulled low to VeeT with a > 30k resistor in the module. RS0 is an input hardware pin which optionally selects the optical receive data path rate coverage for an SFP+ module. RS1 is an input hardware pin which optionally selects the optical transmit path data rate coverage for an SFP+ module. 4 MOD_ABS Mod_ABS is pulled up to Host_Vcc with 4.7k-10k ohms on the host board and connected to VeeT or VeeR in the SFP+ module. MOD_ABS is then asserted "High" when the SFP+ module is physically absent from a host slot. In the SFP MSA (INF8074i) this pin had the same function but is called MOD_DEF0. 5 SCL/SDA SCL is the 2-wire interface clock and SDA is the 2-wire interface data line. SCL and SDA are pulled up to a voltage in the range of 3.14V to 3.46V on the host. 6 RX_LOS RX_LOS when High indicated an optical signal level below that specified in the relevant standard. The RX_LOS pin is an open drain/collector output and must be pulled up to host Vcc with a 4.7k-10k ohms on the host board. RX_LOS assert min and de-assert max are defined in the relevant standard. To avoid spurious transition of RX_LOS a minimum hysteresis of 0.5 dB is recommended. 6 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Recommend Circuit Schematic 7 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Package Outline Drawing for Metal Housing with Bail de-latch Latch Color Identifier Blue SEE COLOR CODE SEE COLOR CODE NOTES: 1.UNITlmm 2.COLOR CODE: BLACK FOR MULTI MODE Complies with 21 CFR 1040.10 and 1040.11 Made in x FS BLUE FOR SINGLE MODE 8 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Timing parameters for SFP+ management Parameter TX_DISABLE Assert time TX_DISABLE Negate time Time to initialize, including reset of TX_FAULT TX Fault Assert Time TX_DISABLE to reset LOS Assert Time LOS Deassert Time Serial ID Clock Rate Symbol t_off t_on Min. t_init t_fault t_reset t_loss_on t_loss_off f_serial_clock Max. 100 1 Unit sec msec Note 1 2 300 msec 3 100 sec sec sec sec kHz 4 5 6 7 10 100 100 400 Notes: 1) Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal 2) Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal 3) From power on or negation of TX_Fault using TX Disable 4) Time from fault to TX fault on. Time TX Disable must be held high to reset TX_Fault 6) Time from LOS state to Rx LOS assert 5) 7) Time from non-LOS state to Rx LOS deassert 9 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Enhanced Digital Diagnostic Interface The memory map in the following describes an extension to the memory map defined in SFP MSA. The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic information about the module's present operating conditions. 2 wire address 1010000 X (A0h) 2 wire address 1010001 X (A2h) 0 0 Alarm and Warning Thresholds (56 bytes) 55 Serial ID Defined by SFP MSA (96 bytes) 56 Cal Constants (40 bytes) 95 96 95 96 Real Time Diagnostic Interface (24 bytes) 119 Vender Specific (32 bytes) 120 Vender Specific 127 127 128 128 User Writable EEPROM (120 bytes) Reserved in SFP MSA (128 bytes) 247 248 255 255 Vender Specific (8 bytes) Digital Diagnostic Memory Map Specific Data Field Descriptions 10 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx EEPROM Serial ID Memory Contents (2-Wire Address A0h) Address 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Hex 03 04 07 00 00 00 00 12 00 00 40 03 55 00 0A 64 00 00 00 00 44 45 4C 54 41 20 20 20 20 20 20 20 20 20 20 20 00 00 00 00 4C 43 50 ASCII D E L T A L C P Address 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 Hex 2D 38 35 30 30 42 34 51 44 52 20 20 20 41 20 20 20 05 1E 00 CS1 00 1A 00 00 SN SN SN SN SN SN SN SN SN SN SN SN SN SN SN SN DC DC ASCII 8 5 0 0 B 4 Q D R Note 1 Note 2 Note 3 Address 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Hex DC DC DC DC DC DC 68 F0 03 CS2 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ASCII Note 4 Note 5 Notes: 1) Byte 63: Check sum of bytes 0-62. 2) Byte 68-83: Serial number. 3) Byte 84-91: Date code. 4) Byte 95: Check sum of bytes 64-94. 5) Byte 128 to 255 had been set hex 00. 11 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Digital Diagnostic Monitoring Interface Alarm and Warning Thresholds (2-Wire Address A2h) Address # Bytes 00-01 02-03 04-05 06-07 08-09 10-11 12-13 14-15 16-17 18-19 20-21 22-23 24-25 26-27 28-29 30-31 32-33 34-35 36-37 38-39 40-45 56-91 92-94 95 96-97 98-99 100-101 102-103 104-105 106-109 110 111 112-119 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 16 36 3 1 2 2 2 2 2 4 1 1 8 Name Temp High Alarm Temp Low Alarm Temp High Warning Temp Low Warning Voltage High Alarm Voltage Low Alarm Voltage High Warning Voltage Low Warning Bias High Alarm Bias Low Alarm Bias High Warning Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning TX Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning Reversed External Calibration Constants Reversed Checksum Real Time Temperature Real Time Supply Voltage Real Time Tx Bias Current Real Time Tx Optical Power Real Time Rx Received Power Reserved Optional Status/ Control Bits Reserved Optional Set of Alarm and Warning Value (Dec.) Unit Note TC (MAX.)+8 TC (MIN.)-8 TC (MAX.)+3 TC (MIN.)-3 3.8 2.8 3.5 3.1 IOP*2+35 IOP-13 IOP *2+30 IOP -8 2.5 -10.4 1.5 -9.4 2.5 -15.8 1.5 -14.8 1 Volt mA 2 dBm dBm 3 4 5 Notes: 1) TC: Case Operating temperature 2) IOP: Operating current at room temperature. The min. setting current is 0 mA. 3) Byte 95 contains the low order 8bits of sum of bytes 0~94 12 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx 4) State/ Control Bits Byte 110 110 110 110 110 110 110 110 Bit 7 6 5 4 3 2 1 0 Name Tx Disable State Soft Tx Disable Reserved Rate Select State Soft Rate Select Tx Fault LOS Data_Ready_Bar Description Digital state of the Tx disable input pin Read/ Write bit that allow software disable of laser Rate Select State Software Rate Select State Digital state of the Tx fault output pin Digital state of the LOS output pin. NA 5) Optional Set of Alarm and Warning Byte 112 112 112 112 112 112 112 112 113 113 113 116 116 116 116 116 116 116 116 117 117 117 Bit 7 6 5 4 3 2 1 0 7 6 5-0 7 6 5 4 3 2 1 0 7 6 5-0 Name Temp High Alarm Temp Low Alarm Vcc High Alarm Vcc Low Alarm Tx Bias High Alarm Tx Bias Low Alarm Tx Power High Alarm Tx Power Low Alarm Rx Power High Alarm Rx Power Low Alarm Reserved Temp High Warning Temp Low Warning Vcc High Warning Vcc Low Warning Tx Bias High Warning Tx Bias Low Warning Tx Power High Warning Tx Power Low Warning Rx Power High Warning Rx Power Low Warning Reserved Description Set when internal temperature exceeds high alarm level Set when internal temperature is below low alarm level Set when internal supply voltage exceeds high alarm level Set when internal supply voltage is below low alarm level Set when Tx Bias current exceeds high alarm level Set when Tx Bias current is below low alarm level Set when Tx output power exceeds high alarm level Set when Tx output power is below low alarm level Set when received power exceeds high alarm level Set when received power is below low alarm level Set when internal temperature exceeds high warning level Set when internal temperature is below low warning level Set when internal supply voltage exceeds high warning level Set when internal supply voltage is below low warning level Set when Tx Bias current exceeds high warning level Set when Tx Bias current is below low warning level Set when Tx output power exceeds high warning level Set when Tx output power is below low warning level Set when received power exceeds high warning level Set when received power is below low warning level Digital Diagnostic Monitor Accuracy Parameter Transceiver Temperature Power Supply Voltage TX Bias Current TX Optical Power RX Optical Power Typical Value 3 3% 10% 3dB 3dB Note 1 Notes: 1) Voltage is measured internal to the transceiver 13 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com LCP-8500B4QDRx Regulatory Compliance Feature Reference Electromagnetic Interference (EMI) FCC Part15 Class B Electrostatic Discharge (ESD) IEC/EN 61000-4-2 MIL-STD-883E EIA-JESD22-A115-A IEC 60825-1:2001 EN 60825 Laser Eye Safety IEC/EN 60950-1 UL60950 Component Recognition Ordering Information for SFP modules LCP-8500B4QDRX1 X1: Temperature Blank: -5 to +70 degree C H: -10 to +85 degree C T: -40 to +85 degree C Appendix A. Document Revision Version No. Date S0 2010-06-04 Description Add the industrial temperature application. 14 DELTA ELECTRONICS, INC. Revision: S0 2010/6/4 www.deltaww.com