PDSP16330/A/B Pythagoras Processor Supersedes version in December 1993 Digital Video & DSP IC Handbook, HB3923-1 DS3884 - 1.3 September 1996 The PDSP16330 is a high speed digital CMOS IC that converts Cartesian data (Real and Imaginary) into Polar form (Magnitude and Phase), at rates up to 20MHz. Cartesian 16+16 bit 2's complement or Sign-Magnitude data is converted into 16 bit Phase format. The Magnitude output may be scaled in amplitude by powers of 2. The Phase output represents a full 2 x field to eliminate phase ambiguities. PIN 1A INDEX MARK ON TOP SURFACE A B C Polyimide is used as an inter-layer dielectric and as glassivation. D E F The PDSP16330 is offered in three speed grades: a basic 10MHz part (PDSP16330), a 20MHz version (PDSP16330A) and a 25MHz version (PDSP16330). A MILSTD-883 version is also detailed in a separate datasheet. G H J K L FEATURES 25MHz Cartesian to Polar Conversion 16-Bit Cartesian Inputs 16-Bit Magnitude Output 12-Bit Phase Output 2's Complement or Sign-Magnitude Input Formats Three-state Outputs and Independent Data Enables Simplify System Interfacing Magnitude Scaling Facility with Overflow Flag Less than 400 mW Power Dissipation at 10MHz 84-pin PGA or 100 pin QFP Package or 84 LCC 11 10 9 8 7 6 5 4 3 2 1 AC84 Fig.1 Pin connections - bottom view (PGA) APPLICATIONS Digital Signal Processing Digital Radio Radar Processing Sonar Processing Robotics ASSOCIATED PPODUCTS PDSP16112 PDSP16116 PDSP16318 PDSP16350 PDSP16510A 16 X 12 Complex Multiplier 16 X 16 Complex Multiplier Complex Accumulator I/Q Splitter and NCO Stand Alone FFT Processor GG100/R Fig.2 Pin connections - QFP Package PDSP16330/A/B Fig.2 Block diagram FUNCTIONAL DESCRIPTION The PDSP16330 converts incoming Cartesian Data into the equivalent Polar Values. The device accepts new 16 + 16 bit complex data every cycle, and delivers a 16 bit + 12 bit Polar equivalent after 24 clock cycles.The input data can be in 2s' Complement or Sign Magnitude format selected via the FORM input. The output is in a magnitude format for both the Magnitude output and the Phase. Phase data is zero for data with a zero Y input and positive X, and is 400 hex for zero X data and positive Y, is 800 hex for zero Y data and negative X, and is C00 hex for zero X and negative Y. The LSB weighting (bit 0) is 2 x /4096 radians. The 16 bit Magnitude result may be scaled by shifting one, two, or three places in the more significant direction, effectively multiplying the Magnitude result by 2,4 or 8 respectively. Any of these shifts can under certain conditions cause an invalid result to be output from the device. Under these circumstances the OVR output will become active. The PDSP16330 has independent clock enables and three state output controls for all ports. S1-0 These inputs select the scaling factor to be applied to the Magnitude output. They are latched by the rising edge of CLK and determine the scaling of the output in the cycle after they are loaded into the device. The scale factor applied is determined by the table. Should the scaling factor applied cause an invalid Magnitude result to be output on the M Port, then the OVR Flag will become active for the period that the M Port output is invalid. S1 S0 Scaling Factor 0 0 x1 0 1 x2 1 0 x4 1 1 x8 FORM This input selects the format of the X and Y input data. A low level on FORM indlcates that the Input data is twos' complement format (Note: input data 8000 hex is not valid in 2s' complement mode). This input refers to the format of the current Input data and may be changed on a per cycle basis if desired. The level of FORM is latched at the same time as the data to which it refers. 2 The output number range is from 0 to 2 when the scaling factor is set at x1. PDSP16330/A/B PIN DESCRIPTIONS Symbol Pin Name and Description CLK Vcc Clock: Common Clock to device Registers. Register contents change on the rising edge of clock. Both pins must be connected. Clock Enable: Clock Enable for X Port. The clock to the X port is enabled by a low level. Clock Enable: Clock Enable for Y Port The clock to the Y port is enabled by a low level. X Data Input Data presented to this input is loaded into the device by the rising edge of CLK. X15 is the MSB Y Data Input Data presented to this input is loaded into the device by the rising edge of CLK. Y15 is the MSB M Data Output: Magnitude data generated by the device is output on this port. Data changes on the rising edge of CLK, M15 is the MSB. The weighting of M15 is determined by the Scale factor selected . P Data Output: Phase data generated by the device is output on this port. Data changes on the rising edge of CLK, P11 is the MSB. The weighting of P11 is radians. Output Enable: Output Enable for M Port. The M Port is in a high impedance state when this input is high. Output Enable: Output Enable for P Port. The P Port is in a high impedance state when this input is high. Format Select This input selects the format of the Cartesian Data input on the X and Y ports. This input is latched by the rising edge of CLK, and is applied at the same time as the data to which it refers. A low !evel indicates that two's complement data is applied, a high indicates Sign-Magnitude Scaling Control: Control input for scaling of Magnitude Data. This input is latched by the rising edge of CLK, and determines the scaling to be applied to the Magnitude result. The Scaling is applied to the output data in the cycle following the cycle in which the control was latched. Overflow: Overflow flag. This signal becomes active if the scaling currently selected causes an invalid value to be presented to the Magnitude output. +5V supply. All Vcc pins must be connected. GND 0V supply. All GND pins must be connected. CEX CEY X15-X0 Y15-Y0 M15-M0 P11-P0 OEM OEP FORM S1-S0 OVR INPUT DATA RANGE 2's Complement Sign Magnitude 7FFF . . . 0001 0000 FFFF . . . 8001 7FFF . . . 0001 0000 8000 . . . FFF 3 PDSP16330/A/B PIN FUNCTION Pin No. AC GG Function Pin No. AC GG Function Pin No. AC F3 G3 G1 G2 F1 H1 H2 J1 K1 J2 L1 K2 K3 L2 L3 K4 L4 J5 K5 L5 K6 J6 J7 L7 K7 L6 L8 K8 91 92 93 94 95 96 97 98 99 100 1 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 M7 M6 M5 M4 M3 M2 M1 M0 S0 S1 GND Vcc FORM Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8 Y7 Y6 Y5 Y4 Y3 Y2 Y1 L9 L10 K9 L11 K10 J10 K11 J11 H10 H11 F10 G10 G11 G9 F9 F11 E11 E10 E9 D11 D10 C11 B11 C10 A11 B10 B9 A10 23 24 25 26 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 57 58 YO CEY CLK Vcc GND GND GND GND GND GND GND OEP P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 GND Vcc CEX X0 A9 B8 A8 B6 B7 A7 C7 C6 A6 A5 B5 C5 A4 B4 A3 A2 B3 A1 B2 C2 B1 C1 D2 D1 E3 E2 E1 F2 GG Function 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 81 82 83 84 85 86 87 88 89 90 X1 X2 X3 X4 X5 X6 X7 X8 X9 X10 X11 X12 X13 X14 X15 CLK OVR Vcc GND OEM M15 M14 M13 M12 M11 M10 M9 M8 ELECTRICAL CHARACTERISTICS Test conditions (unless otherwise stated): Tamb (Commercial) = 0C to + 70C, Tamb (Industrial) = -40C to + 85C Vcc (Commercial) = 5.0V + 5%, Vcc (Industrial and Military) = 5.0V + 1%, GND = 0V STATIC CHARACTERISTICS Value Characteristic Min. * * * * * * * * Output high voltage Output low voltage Input high voltage (CMOS) Input low voltage (CMOS) Input high voltage (TTL) Input low voltage (TTL) Input leakage current (Note 1 ) Input capacitance Output leakage current Output SC current SubUnits group Symbol VOH VOL VIH VIL VIH VIL IIL CIN loz IOS Typ. 2.4 0.6 3.0 1.0 2.2 0.8 + 120 -10 10 -50 -50 Conditions Max. + 50 230 V V V V V V A pF A mA 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 IOH = 3.2mA lOL=-3.2mA Inputs CEX, CEY and CLK only Inputs CEX, CEY and CLK only All other inputs All other inputs GND < VIN<VCC 1,2,3 GND <VIN < VCC Vcc = Max NOTES 1. All inputs except clock inputs have high value pull-down resistors 2. All parameters marked * are tested during production. Parameters marked are guaranteed by design and characterisation. 4 PDSP16330/A/B SWITCHING CHARACTERISTICS Value Characteristic PDSP16330 Min. * Input data setup to clock rising edge Input data Hold after clock rising edge CEX, CEY Setup to clock rising edge CEX, CEY Hold aher clock rising edge FORM, S1:0 Setup to clock rising edge FORM, S1:0 Hold after clock rising edge Clock rising edge to valid data Clock period Clock high time Clock low time Latency OEM, OEP low to data high data valid OEM, OEP low to data low data valid OEM, OEP high to data high impedance OEM, OEP low to data high impedance Vcc current (TTL input levels) Vcc current (CMOS input levels) 15 2 30 0 15 7 5 100 25 25 24 Max. 40 24 30 30 30 30 110 70 PDSP16330A PDSP16330B Min. 12 2 12 0 12 2 5 50 15 15 24 Max. Min. 24 25 25 25 25 180 12 2 12 0 12 2 5 40 15 15 24 25 25 25 25 225 120 150 25 Units Conditions Max. 25 24 ns ns ns ns ns ns ns ns ns ns cycles ns ns ns ns mA mA 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF VCC = Max Outputs unloaded Clock freq. = Max VCC = Max Outputs unloaded Clock freq. = Max NOTES 1. LSTTL is equivalent to IOH = 20A, I OL = -0.4mA 2. Current is defined as negative into the device 3. CMOS input levels are defined as: VIH = VDD - 0.5V, VIL = +0.5V 4. All parameters marked * are tested during production. Parameters marked are guaranteed by design and characterisation. 5. All timings are dependent on silicon speed. This speed is tested by measuring clock period. This guarantees all other timings by characterisation and design. ABSOLUTE MAXIMUM RATINGS Supply voltage, Vcc -0.5V to + 7.0V Input voltage, VIN -0.5V to VCC + 0.5V Output voltage, Vour -0.5V to VCC + 0.5V Clamp diode current per pin, IK (see Note 2) 18mA Static discharge voltage (HMB), VSTAT 500V Storage temperature. Tstg -65C to + 150C Ambient temperature with power applied Tamb: Commercial 0C to + 70C Industrial -40C to + 85C Military -55 C to + 125C Package power dissipation PTOT 1200mW Junction temperature 150C THERMAL CHARACTERISTICS Package Type AC GG JCC/W JAC/W 12 12 36 35 NOTES 1. Exceeding these ratings may cause permanent damage. Functional operatlon under these conditions is not implied. 2. Maximum dissipation or 1 second should not be exceeded; only one output to be tested at any one time. 3. Exposure to Absoulte Maximum Ratings for extended periods may affect device reliability. 5 PDSP16330/A/B ORDERING INFORMATION Commercial (0C to +70C) PDSP16330 CO AC PDSP16330A CO AC PDSP16330B CO AC (10MHZ - PGA Package) (20MHZ - PGA Package) (25MHZ - PGA Package) Industrial (-40C to +85C) PDSP16330 PDSP16330A PDSP16330A PDSP16330B BO BO BO BO AC AC GG AC 10MHZ 20MHZ 20MHZ 25MHZ - PGA Package PGA Package GG Package PGA Package 20MHZ 20MHZ 10MHz 20MHz - PGA Package GG Package GG Package Mil 883C Screened PGA Package Mil 883C Screened Military (-55C to +125C) PDSP16330A PDSP16330A PDSP16330 PDSP16330A 6 AO AO AC AC AC GG GG AC PDSP16330/A/B Fig.3 Three state delay measurement load 7 PDSP16330/A/B 8 PDSP16330/A/B 9 PDSP16330/A/B 10 PDSP16330/A/B 11 PDSP16330/A/B HEADQUARTERS OPERATIONS MITEL SEMICONDUCTOR Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (01793) 518000 Fax: (01793) 518411 MITEL SEMICONDUCTOR 1500 Green Hills Road, Scotts Valley, California 95066-4922 United States of America. Tel (408) 438 2900 Fax: (408) 438 5576/6231 Internet: http://www.gpsemi.com CUSTOMER SERVICE CENTRES FRANCE & BENELUX Les Ulis Cedex Tel: (1) 69 18 90 00 Fax : (1) 64 46 06 07 GERMANY Munich Tel: (089) 419508-20 Fax : (089) 419508-55 ITALY Milan Tel: (02) 6607151 Fax: (02) 66040993 JAPAN Tokyo Tel: (03) 5276-5501 Fax: (03) 5276-5510 KOREA Seoul Tel: (2) 5668141 Fax: (2) 5697933 NORTH AMERICA Scotts Valley, USA Tel: (408) 438 2900 Fax: (408) 438 5576/6231 SOUTH EAST ASIA Singapore Tel:(65) 3827708 Fax: (65) 3828872 SWEDEN Stockholm Tel: 46 8 702 97 70 Fax: 46 8 640 47 36 TAIWAN, ROC Taipei Tel: 886 2 25461260 Fax: 886 2 27190260 UK, EIRE, DENMARK, FINLAND & NORWAY Swindon Tel: (01793) 726666 Fax : (01793) 518582 These are supported by Agents and Distributors in major countries world-wide. (c) Mitel Corporation 1998 Publication No. DS3884 Issue No. 1.3 September 1996 TECHNICAL DOCUMENTATION - NOT FOR RESALE. PRINTED IN UNITED KINGDOM This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. 12