4/98
ES1A THRU ES1D
SURFACE MOUNT ULTRAFAST EFFICIENT PLASTIC RECTIFIER
Reverse Voltage - 50 to 200 Volts Forward Current - 1.0 Ampere
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ For surface mount applications
♦ Low profile package
♦ Ideally suited for use in
very high frequency switching power supplies,
inver ters and as a free wheeling diodes
♦ Ultrafast recover y times for high efficiency
♦ Low forward voltage
♦ Low leakage current
♦ Glass passivated chip junction
♦ High temperature soldering guaranteed:
250°C/10 seconds on terminals
MECHANICAL DATA
Case: JEDEC DO-214AC molded plastic body over
passivated chip
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Weight: 0.002 ounces, 0.064 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS ES1A ES1B ES1C ES1D UNITS
Device mar king code EA EB EC ED
Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts
Maximum RMS voltage VRMS 35 70 105 140 Volts
Maximum DC blocking voltage VDC 50 100 150 200 Volts
Maximum average forward rectified current
at TL=120°C I(AV) 1.0 Amp
Peak forward surge current
8.3ms single half sine-wave superimposed on IFSM 30.0 Amps
rated load (JEDEC Method)
Maximum instantaneous forward voltage at 0.6A 0.865
at 1.0A VF0.920 Volts
Maximum DC reverse current TA=25°C 5.0
at rated DC blocking voltage TA=100°C IR100 µA
Maximum reverse recover y time (NOTE 1) trr 15.0 ns
Maximum reverse recover y time TA=25°C 25.0
(NOTE 2) TA=100°C trr 35.0 ns
Maximum stored charge TA=25°C 10.0
(NOTE 2) TA=100°C Qrr 25.0 nC
Typical junction capacitance (NOTE 3) CJ7.0 pF
Maximum thermal resistance (NOTE 4) RΘJA 85.0 °C/W
RΘJL 35.0
Operating and storage temperature range TJ, TSTG -55 to +150 °C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) trr and Qrr measured at: IF=0.6A, VR=30V, di/dt=50A/µs, Irr =10% IRM for measurement of trr
(3) Measured at 1.0 MHZand applied reverse voltage of 4.0 volts
(4) P.C.B. mounted on 0.2 x 0.2” (5.0 x 5.0mm)copper pad area
0.157 (3.99)
0.177 (4.50)
0.006 (0.152)
0.012 (0.305)
0.030 (0.76)
0.060 (1.52) 0.008 (0.203) MAX.
0.194 (4.93)
0.208 (5.28)
0.100 (2.54)
0.110 (2.79)
0.078 (1.98)
0.090 (2.29)
0.049 (1.25)
0.065 (1.65)
DO-214AC
Dimensions in inches and (millimeters)
80 90 100 110 120 130 140 150
0
0.2
0.4
0.6
0.8
1.0
1.2
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
0.01
0.1
1
10
50
0.1 1 10 100
0
2.0
4.0
6.0
8.0
10
12
14
110100
5.0
10
15
20
25
30
0
0.1 1 10 100
1
10
100
020406080100
0.01
0.1
1
10
100
1,000
RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1D
FIG. 1 - MAXIMUM FORWARD CURRENT
DERATING CURVE
LEAD TEMPERATURE, °C
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 HZ
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT,
AMPERES
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
MICROAMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, pF
REVERSE V OLTAGE, V OLTS
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method) at TL=120°C
TJ=125°C
TJ=85°C
TJ=25°C
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
TJ=25°C
f=1.0 MHZ
Vsig=50mVp-p
RESISTIVE OR
INDUCTIVE LOAD
0.2 x 0.2” (5.0 x 5.0mm)
COPPER PAD AREAS
FIG. 5 - TYPICAL THERMAL IMPEDANCE
TRANSIENT THERMAL IMPED ANCE, °C/W
MOUNTED on 0.2 x 0.2”(5 x 7mm)
COPPER PAD AREAS
t, PULSE DURATION, SEC
