GENERAL
TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL ±
2.0 °
SERIES MATERIAL NUMBER CUSTOMER
GENERAL MARKET
170475
SEE TABLE
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.13
1 PLACE
±
0.25
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
1 OF 3
DIMENSION UNITS SCALE
MM 4:1
DRWN BY DATE
JBINGHAM 2010/05/19
CHK'D BY DATE
JLAURX 2010/05/19
APPR BY DATE
JLAURX 2013/05/21
DOCUMENT NUMBER
DOC TYPE
DOC PART
SD-170475-0002 PSD 001
DRAWING SIZE
THIRD ANGLE PROJECTION
C
IMPACT 5-PAIR 85-OHM
LEFT GUIDED BACKPLANE SALES ASSEMBLY
DRAWING
PRODUCT CUSTOMER DRAWING
MIGRATED TO NX
2017/10/25
2017/11/30
2017/12/01
168852
NVELUSAMY
CD
GGA
EC NO:
DRWN:
CHK'D:
APPR:
D3
REV
FORMAT: master-tb-prod-C
REVISION: G
DATE: 2015/02/06
RELEASE STATUS P1 RELEASE DATE 01.12.2017 12:29:05
Z
Z
SECTION Z-Z
UNPLATED
SCREW HOLE
3.56
0.08
LEFT GUIDED
BACKPLANE HOLE PATTERN
(CONNECTOR SIDE)
SEE NOTE 5
24.8 +0.2
-0.5
1.90
SEE PART NUMBER CHART
AND
PART NUMBER LOGIC
(15 HOLES PER COLUMN)
14X
1.35
ROW A
0.15
SEE NOTE #7
0.10
11.95
KEEP OUT ZONE
2.95
2.64
18.90
NOTCH DESIGNATES
ROW A
20.4
P
PIN LENGTH
0.20
28.6
NOTES:
1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP)
GLASS-FILLED, UL94V-0
TERMINALS - HIGH PERFORMANCE COPPER ALLOY
2. FINISH: 30µ INCH MIN GOLD IN CONTACT AREA, SELECTIVE MATTE TIN ON PCB TAILS, NICKEL OVERALL.
3. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS.
4. CONNECTORS SUPPLIED WITH A 2-56 UNC-2A SCREW.
5. "THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMMODATE CONNECTOR
INSERTION AND REPAIR ON THE PC BOARD. THIS IS REFERRED TO AS THE "CONNECTOR
KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE
CONNECTOR. WHEN LAYING OUT A PC BOARD FOR CONNECTORS STACK TOGETHER,
USE A 1.9mm PROGRESSION."'
6. SEE SHEETS 2 & 3 FOR PART NUMBERS AND BOARD RELATIONSHIPS.
7. FOR GROUNDED GUIDE PINS USE
3.56
0.08 (PTH),
3.66 (DRILL) &
6.5 (PAD).
8. MINIMUM CIRCUIT BOARD THICKNESS: 1.0mm.
9. REFER TO MOLEX PRODUCT SPECIFICATION PS-170540-999
FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION.
10. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF
MOLEX COSMETIC SPEC PS-45499-002.
11. PARTS PACKAGED PER PK-70873-759.
TAIL LENGTH
1.4
A
B
B
8.50 0.95
ADD FOR END WALL
1.35
1.90
PIN A1
4.75
24.8 18.90
13.21
2.95
14X
1.35
SIGNAL HOLES
REF.
GROUND HOLES
REF.
ROW P
ROW O
ROW N
ROW M
ROW L
ROW K
ROW J
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
ROW B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
GENERAL
TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL ±
2.0 °
SERIES MATERIAL NUMBER CUSTOMER
GENERAL MARKET
170475
SEE TABLE
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.13
1 PLACE
±
0.25
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
2 OF 3
DIMENSION UNITS SCALE
MM 2:1
DRWN BY DATE
JBINGHAM 2010/05/19
CHK'D BY DATE
JLAURX 2010/05/19
APPR BY DATE
JLAURX 2013/05/21
DOCUMENT NUMBER
DOC TYPE
DOC PART
SD-170475-0002 PSD 001
DRAWING SIZE
THIRD ANGLE PROJECTION
C
IMPACT 5-PAIR 85-OHM
LEFT GUIDED BACKPLANE SALES ASSEMBLY
DRAWING
PRODUCT CUSTOMER DRAWING
MIGRATED TO NX
2017/10/25
2017/11/30
2017/12/01
168852
NVELUSAMY
CD
GGA
EC NO:
DRWN:
CHK'D:
APPR:
D3
REV
FORMAT: master-tb-prod-C
REVISION: G
DATE: 2015/02/06
RELEASE STATUS P1 RELEASE DATE 01.12.2017 12:29:05
MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B
GUIDE LEFT
OPEN WALL
OPTION
170475-38** 8 40 21.7 13.30
170475-31** 10 50 25.5 17.10
170475-32** 12 60 29.3 20.90
170475-36** 16 80 36.9 28.50
MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM. A DIM. B
GUIDE LEFT
END WALL
OPTION
170475-78** 8 40 23.1 13.30
170475-71** 10 50 26.9 17.10
170475-72** 12 60 30.7 20.90
170475-76** 16 80 38.3 28.50
GUIDE LEFT
OPEN WALL OPTION
GUIDE LEFT
END WALL OPTION
****
PART NUMBER LOGIC
170475-
3 = 4.50 (SHORT COMPLIANT, 0.46
0.05 PTH)
4 = 4.90 (SHORT COMPLIANT, 0.46
0.05 PTH)
5 = 5.50 (SHORT COMPLIANT, 0.46
0.05 PTH)
6 = 4.50 (MICRO COMPLIANT, 0.39
0.05 PTH)
7 = 4.90 (MICRO COMPLIANT, 0.39
0.05 PTH)
8 = 5.50 (MICRO COMPLIANT, 0.39
0.05 PTH)
# OF COLUMNS
1 = 10 COL
2 = 12 COL
6 = 16 COL
8 = 8 COL KEY ORIENTATION
0 = NO KEY
1 = A
2 = B
3 = C
4 = D
5 = E
6 = F
7 = G
8 = H
MODULE TYPE
3 = GUIDE LEFT, MATTE TIN
7 = GUIDE LEFT END WALL, MATTE TIN
P=PIN LENGTH
PART NUMBER CHART
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
GENERAL
TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL ±
2.0 °
SERIES MATERIAL NUMBER CUSTOMER
GENERAL MARKET
170475
SEE TABLE
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.13
1 PLACE
±
0.25
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
3 OF 3
DIMENSION UNITS SCALE
MM 3:1
DRWN BY DATE
JBINGHAM 2010/05/19
CHK'D BY DATE
JLAURX 2010/05/19
APPR BY DATE
JLAURX 2013/05/21
DOCUMENT NUMBER
DOC TYPE
DOC PART
SD-170475-0002 PSD 001
DRAWING SIZE
THIRD ANGLE PROJECTION
C
IMPACT 5-PAIR 85-OHM
LEFT GUIDED BACKPLANE SALES ASSEMBLY
DRAWING
PRODUCT CUSTOMER DRAWING
MIGRATED TO NX
2017/10/25
2017/11/30
2017/12/01
168852
NVELUSAMY
CD
GGA
EC NO:
DRWN:
CHK'D:
APPR:
D3
REV
FORMAT: master-tb-prod-C
REVISION: G
DATE: 2015/02/06
RELEASE STATUS P1 RELEASE DATE 01.12.2017 12:29:05
IMPACT 5 PAIR
BOARD RELATIONSHIPS
BP ROW A
BP ROW A
BPLANE PCB
DCARD PCB
DC HOLE COLUMN
(COLUMN 10 REF.)
BP HOLE COLUMN
(COLUMN 10 REF.)
DCARD ROW A
DCARD PCB
BPLANE PCB
24.8
DCARD ROW A
3.0
14.0
11.95
0.35
OFFSET BETWEEN DC AND
BP HOLE COLUMNS
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
