DENSEI-LAMBDA HWS15/A SPECIFICATIONS A224-01-01/A-B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 MODEL ITEMS Nominal Output Voltage Maximum Output Current Maximum Output Power Efficiency (Typ) (*1) 100VAC 200VAC Input Voltage Range (*2) Input Current (100/200VAC)(Typ) (*1) Inrush Current(Typ) (*3) PFHC Output Voltage Range 0<Ta<60C Maximum Ripple & Noise (*4) -10<Ta<0C Maximum Line Regulation (*5) Maximum Load Regulation (*6) Temperature Coefficient Over Current Protection (*7) Over Voltage Protection (*8) Hold-up Time (Typ) (*9) Leakage Current (*10) Remote Sensing Parallel Operation Series Operation Operating Temperature (*11) Operating Humidity Storage Temperature Storage Humidity Cooling Withstand Voltage 27 Isolation Resistance 28 Vibration 29 Shock (In package) 30 Safety 31 32 33 34 Line DIP Conducted Emission Radiated Emission Immunity 35 Weight(Typ.) 36 Size (W x H x D) V A W % % A V mV mV mV mV A V - (*12) mm HWS15 -3/A 3.3 3 10 68 71 HWS15 HWS15 HWS15 HWS15 HWS15 -5/A -12/A -15/A -24/A -48/A 5 12 15 24 48 3 1.3 1 0.65 0.33 15 15.6 15 15.6 15.8 77 80 80 82 80 79 81 81 83 80 85 ~ 265VAC (47 ~ 63Hz) or 120 ~ 370VDC 0.3/0.15 0.4/0.2 14A at 100VAC, 28A at 200VAC, Ta=25C, Cold Start Built to meet IEC61000-3-2 2.97~3.96 4.0~6.0 9.6~14.4 12.0~18.0 19.2~28.8 38.4~52.8 120 120 150 150 200 200 160 160 180 180 240 240 20 20 48 60 96 192 40 40 96 120 192 384 Less than 0.02% / C 3.15 ~ 3.15 ~ 1.36 ~ 1.05 ~ 0.68 ~ 0.34 ~ 4.13~4.95 6.25~7.25 15.0~17.4 18.8~21.8 30.0~34.8 55.2~64.8 20ms Less than 0.5mA. 0.2mA(Typ) at 100VAC / 0.4mA(Typ) at 230VAC Possible -10 ~+60C (-10 ~+40C:100%,+50C:60%,+60C:20%) 30 ~ 90%RH (No dewdrop) -30 ~ +85C 10 ~ 95%RH (No dewdrop) Convection Cooling Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA) Output - FG : 500VAC (100mA) for 1min More than 100M at 25C and 70%RH Output - FG : 500VDC At no operating, 10 ~ 55Hz (Sweep for 1min) 19.6m/s2 Constant, X,Y,Z 1hour each. Less than 196.1m/s2 Approved by UL60950-1, CSA60950-1, EN60950-1, EN50178 Built to meet UL508, DENAN Built to meet SEMI-F47 (200VAC Line only) Built to meet EN55011/EN55022-B, FCC-B, VCCI-B Built to meet EN55011/EN55022-B, FCC-B, VCCI-B Built to meet IEC61000-4-2(Level 2,3), -3(Level 3), -4(Level 3), -5(Level 3,4), -6(Level 3), -8(Level 4), -11 210g 31.5 x 82 x 80 ( Refer to Outline Drawing ) *Read instruction manual carefully, before using the power supply unit. =NOTES= *1. At 100/200VAC, Ta=25C and maximum output power. *2. For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 ~ 240VAC(50/60Hz). *3. Not applicable for the in-rush current to Noise Filter for less than 0.2ms. *4. Measure with JEITA RC-9131A probe, Bandwidth of scope :100MHz. For start up at low ambient temperature and low input voltage, output ripple noise might not meet specification. However, there is no overshoot at start up and output ripple noise specification can be met after one second. *5. 85 ~ 265VAC , constant load. *6. No load-Full load, constant input voltage. *7. Foldback current limit with automatic recovery. Not operate at over load or dead short condition for more than 30seconds. *8. OVP circuit will shutdown output, manual reset (Re power on). *9. At 100/200VAC , Ta=25C, nominal output voltage and maximum output current. *10. Measured by the each measuring method of UL,CSA,EN and DENAN(at 60Hz). *11. Ratings - Derating at standard mounting. - Load (%) is percent of maximum output power or maximum output current, whichever is greater. - As for other mountings, refer to derating curve (A224-01-02/A_). *12. As for DENAN, built to meet at 100VAC. DENSEI-LAMBDA HWS15/A OUTPUT DERATING A224-01-02/A LOAD(%) MOUNTING A,B,C,D 100 60 20 Ta(C) -10 ~+40 50 60 OUTPUT DERATING CURVE 120 LOAD(%) 100 80 MOUNTING A,B,C,D 60 40 20 0 -10 0 10 20 30 40 50 60 70 Ta(C) MOUNTING A (STANDARD MOUNTING) MOUNTING B MOUNTING C MOUNTING D DON'T USE