Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series TMOV(R)25S Varistor Series RoHS Description Metal Oxide Varistors (MOVs) are rated for specific AC line operating voltages, and exceeding these limits through the application of a sustained abnormal over-voltage condition could result in overheating and damage to the MOV. The Littelfuse TMOV(R)25S Varistor Series was designed to address this condition in a single integrated package. The TMOV(R)25S Varistor Series incorporates a patented integrated thermally responsive element within the body of the device which will open-circuit the varistor in case of overheating due to the abnormal over-voltage events. Agency Approvals Agency Agency Approval Agency File Number UL1449 E320116 IEC-CECC Spec: QC42201-C001, QC42201-A001, IEC 60950-1 (Annex Q) E1274/F IEC 61051-1, IEC 61051-2, IEC 60950-1 (Annex Q) 40021525 The TMOV(R)25S Varistor Series meets the surge suppressor component recognition requirements of UL1449 3rd edition for both cord connected and permanently connected SPD end products. Features Additional Information RoHS Compliant and Lead-free * Standard lead form and spacing option * Wave solderable * -55C to +85C operating temperature range * * Standard Operating Voltage Range Compatible with Common AC Line Voltages (115VAC to 750VAC * High peak surge current rating up to 20kA at single 8/20S impulse Applications Datasheet Resources Samples * SPD Products * AC Panel Protection Modules * AC/DC power supplies * UPS (Uninterruptible Power Supply) (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series Absolute Maximum Ratings * For ratings of individual members of a series, see Device Ratings and Specifications chart. TMOV(R)25S Varistor Series Units 115 to 750 V 20,000 A Continous AC Voltage Range (VM(AC)RMS) Transient Peak Pulse Current (ITM) For 8x20s Current Wave, single pulse Single-Pulse Energy Capability For 2ms Current Wave 170 to 670 J Operating Ambient Temperature Range (TA) -55 to +85 C Storage Temperature Range (TSTG) -55 to +125 C Temperature Coefficient (V) of Clamping Voltage (VC) at Specified Test Current <0.01 %/C Hi-Pot Encapsulation (COATING Isolation Voltage Capability) 2,500 V Thermal Protection Isolation Voltage Capability (when operated) *See notes under Device Ratings & Specifications section for more information 600* V COATING Insulation Resistance 1,000 M CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Device Ratings & Specifications Maximum Rating (85C) 2 Leaded Device Without Indicator Lead 3 Leaded Device With Indicator Lead Option Continuous Model Size Disc Diameter (mm) AC Volts VM(AC) DC Volts VM(DC) Transient Peak Energy Current 2ms 8/20s WTM ITM 1 x Pulse Specifications (25 C) Clamping Voltage Typical at 100A Capacitance Current (f=1MHz) 8/20s Varistor Voltage at 1mA Test Current VN(DC) Min VN(DC) Max VC C Part Number Branding Part Number Branding (V) (V) (J) (A) TMOV25SP115E P25T115E TMOV25SP115M P25T115M 25 115 150 170 20000 162 198 TMOV25SP130E P25T130E TMOV25SP130M P25T130M 25 130 170 190 20000 184.5 TMOV25SP140E P25T140E TMOV25SP140M P25T140M 25 140 180 210 20000 198 TMOV25SP150E P25T150E TMOV25SP150M P25T150M 25 150 200 220 20000 TMOV25SP175E P25T175E TMOV25SP175M P25T175M 25 175 225 250 20000 TMOV25SP200E P25T200E TMOV25SP200M P25T200M 25 200 265 270 20000 283 345 530 1700 TMOV25SP230E P25T230E TMOV25SP230M P25T230M 25 230 300 300 20000 324 396 585 1500 TMOV25SP250E P25T250E TMOV25SP250M P25T250M 25 250 320 330 20000 351 429 640 1400 TMOV25SP275E P25T275E TMOV25SP275M P25T275M 25 275 350 350 20000 387 473 700 1250 TMOV25SP300E P25T300E TMOV25SP300M P25T300M 25 300 385 370 20000 423 517 765 1150 TMOV25SP320E P25T320E TMOV25SP320M P25T320M 25 320 420 390 20000 459 561 825 1080 TMOV25SP385E P25T385E TMOV25SP385M P25T385M 25 385 505 430 20000 558 682 1010 900 TMOV25SP420E P25T420E TMOV25SP420M P25T420M 25 420 560 460 20000 612 748 1100 820 TMOV25SP440E P25T440E TMOV25SP440M P25T440M 25 440 585 470 20000 643.5 786.5 1160 790 TMOV25SP460E P25T460E TMOV25SP460M P25T460M 25 460 615 490 20000 675 825 1220 750 TMOV25SP510E P25T510E TMOV25SP510M P25T510M 25 510 670 520 20000 738 902 1335 680 TMOV25SP550E P25T550E TMOV25SP550M P25T550M 25 550 745 550 20000 819 1001 1475 630 TMOV25SP625E P25T625E TMOV25SP625M P25T625M 25 625 825 600 20000 900 1100 1625 550 TMOV25SP750E P25T750E TMOV25SP750M P25T750M 25 750 970 670 20000 1080 1320 1950 460 RMS (V) (V) (pF) 295 3200 225.5 335 2800 242 355 2500 216 264 390 2300 243 297 450 1900 Notes: Average power dissipation of transients should not exceed 1.5 watts. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series Thermal Characteristics Peak Current & Energy Derating Curve Typical time to open circuit under UL 1449 Abnormal Overvoltage Limited Current Test: For applications exceeding 85C ambient temperature, the peak surge current and energy ratings must be reduced as shown. 10 PERCENT OF RATED VALUE 100 Current (A) Typical 10 A 5A 1 2.5 A 0.5 A 80 60 40 20 0 -55 0.1 10 Figure 1 100 1000 10000 50 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (C) Figure 2 Time (secs) 60 Transient V-I Characteristic Curves 10000 750 Maximum Peak Voltage (V) 625 420 385 440 550 510 460 1000 275 115 130 140 150 175 230 300 320 250 100 10A Figure 3 100A 1mA 10mA 100mA 1A 10A 100A 1000A 10000A 100000A Peak Current (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series Pulse Rating Curve 100000 Number of Pulses 1 2 15 10000 Surge Current (A) 10 2 10 1000 3 4 10 5 10 10 100 6 10 1 20 100 Figure 4 Wave Solder Profile Because the TMOV(R)25S Varistor Series contains a thermally responsive device, care must be taken when soldering the device into place. Two soldering methods are possible. Firstly, hand soldering: We recommend the use of pliers to heat-sink the leads of the device. Secondly, wave-soldering: This is a strenuous process requiring pre-heat stages to reduce the stresses on devices. It is critically important that all preheat stage and the solder bath temperatures are rigidly controlled. The recommended solder for the TMOV(R) Varistor Series is a 62/36/2 (Sn/Pb/Ag), 60/40 (Sn/Pb) or 63/37 (Sn/ Pb). Littelfuse also recommends an RMA solder flux. SAC solders (SnAgCu) are recommended for Lead-free applications. 1000 10000 Impulse Duration (secs) Soldering Profile 300 MAXIMUM WAVE 260C 250 TEMPERATURE (C) 10 200 150 100 PREHEAT 50 0 0.0 Figure 5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 TIME (MINUTES) (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series Environmental Specifications Physical Specifications Lead Material Tin-coated Copper wire Operating/Storage Temperature -55C to +85C Soldering Characteristics Solderability per MIL-STD-202, Method 208 Humidity Aging +85C, 85%R.H., 1000 hours -/+10% typical voltage change Insulating Material Cured, flame retardant epoxy polymer meets UL94V-0 requirements Thermal Shock +85C to -40C 5 times -/+10% typical voltage change Device Labeling Marked with LF, voltage, UL logos, and date code Solvent Resistance MIL-STD-202, Method 215 Moisture Sensitivity Level 1, J-STD-020 Application Example Line Fuse 3 Monitor Lead Diode 2 LED R The application example left shows how the indicator lead on the TMOV(R) Varistor can be used to indicate that thermal element has been opened. This signifies that the circuit is no longer protected from transients by the MOV. TO PROTECTED CIRCUIT Line Neutral 1 1 2 3 Monitor Lead Dimensions 2 Leaded Device Without Indicator Lead (E part number suffix) 3 Leaded Device With Indicator Lead Option (M part number suffix) E D E D A A Indicator Lead L L b e W2 W2 e1 W W2 e W W2 b (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV(R)25S Varistor Series Product Dimensions (mm) Part Number Part Number WMIN WMAX W2 EMAX TMOV25SP115E TMOV25SP115M 1.5 2.7 3.6+/-1 11.7 TMOV25SP130E TMOV25SP130M 1.6 2.9 3.7+/-1 11.9 TMOV25SP140E TMOV25SP140M 1.7 3.0 3.8+/-1 12.0 TMOV25SP150E TMOV25SP150M 1.8 3.1 3.9+/-1 12.1 TMOV25SP175E TMOV25SP175M 1.9 3.3 4.1+/-1 12.3 TMOV25SP200E TMOV25SP200M 1.9 3.3 4.1+/-1 12.3 TMOV25SP230E TMOV25SP230M 2.0 3.4 4.2+/-1 12.4 TMOV25SP250E TMOV25SP250M 2.1 3.5 4.3+/-1 12.5 TMOV25SP275E TMOV25SP275M 2.3 3.7 4.5+/-1 12.7 TMOV25SP300E TMOV25SP300M 2.4 3.9 4.6+/-1 12.9 TMOV25SP320E TMOV25SP320M 2.6 4.1 4.8+/-1 13.1 TMOV25SP385E TMOV25SP385M 3.0 4.7 5.3+/-1 13.7 TMOV25SP420E TMOV25SP420M 3.3 5.0 5.6+/-1 14.0 TMOV25SP440E TMOV25SP440M 3.4 5.2 5.8+/-1 14.2 TMOV25SP460E TMOV25SP460M 3.6 5.4 6+/-1 14.4 TMOV25SP510E TMOV25SP510M 3.9 5.7 6.3+/-1 14.7 TMOV25SP550E TMOV25SP550M 4.2 6.2 6.7+/-1 15.2 TMOV25SP625E TMOV25SP625M 4.6 6.6 7.1+/-1 15.6 TMOV25SP750E TMOV25SP750M 5.4 7.7 8.0+/-1 16.7 AMAX bMIN bMAX DMAX e e1 L 34.5 0.95 1.05 28 19.2 +/-1 12.7 +/-1 12.7 Min. Part Numbering System TMOV 25 S P 150 M XXXXX DEVICE FAMILY NON-STANDARD OPTION CODES Littelfuse thermally responsive MOV SERIES DESIGNATOR DISC DIAMETER (mm) E: 2-Leaded Device - Without Indicator Lead M: 3-Leaded Device - With Indicator Lead Option 25mm CERAMIC SHAPE S: Square VM(AC)RMS 115V TO 750V P: LEAD-FREE AND RoHS COMPLIANT OPTION Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/19/19