SDV-FL1-DC12 - Omron - Datasheet.Live

CSM_SDV_DS_E_6_1

Voltage Sensor

SDV

Overvoltage/Undervoltage Monitoring

Relay for AC and DC Input

• Detect overvoltages or undervoltages (switch select-

able) from 4 mV to 300 V.

• Detect undercurrent, reverse current, or overcurrent in

DC circuits using shunt (SDV-FL).

• Detect three-phase AC current for under and/or overcur-

rent using current converter.

• Available in 7 supply voltage configurations.

• Single-function model with ON-delay, OFF-delay, or star-

tup lock settings (SDV-FH@T).

• Select either AC or DC voltage input.

• Polarity can be specified (SDV-FL) to enable easy re-

verse current detection.

• Selectable reset value range from 2% to 30% of operat-

ing value (SDV-F).

• LED operation indicator.

• UL/CSA approval (single-function models).

Model Number Structure

■Model Number Legend

1. Voltage Sensor

2. Operation

F: Single-function (overvoltage or undervoltage detection)

D: Dual-function (overvoltage and undervoltage detection)

3. Operating Voltage Range

L: 4 to 240 mV (DC input only) (For SDV-F only)

M: 0.2 to 12 V (AC or DC input)

H: 10 to 300 V (AC or DC input)

4, 5. Control Power Supply Voltage

2: 24 VDC

3: 48 VDC

4: 100/110 VDC

5: 125 VDC

51: 200/220 VDC (Single-function models)

6: 100/110 VAC

61: 120 VAC (Single-function models)

7: 200/220 VAC

71: 240 VAC (Single-function models)

6. Timing Function (SDV-FH Only (See Note))

None: Not provided

T: Provided

Note: SDV-FL and SDV-FM models can also be equipped with the

timing function as a special specification. Ask your OMRON

representative for details.

Note: Not possible for the SDV equipped with the timing function

(SDV-FH@T).

SDV-@@@@@

123456

SDV

1. Shunt (For SDV-FL Only)

2, 3, 4, 5. Rated Current

Available Models

Note: All the above listed shunts have an accuracy in the 1.0 class.

Connecting Socket (Order Separately)

Ordering Information

Single-function Models

Overvoltage or Undervoltage Detection (Switch Selectable)

Dual-function Models

Overvoltage and Undervoltage Detection

Note: 1. Inquire about production of models with 120- and 240-VAC control power supply.

2. Inquire about models with special processing for high-temperature, high-humidity applications.

3. The ripple factor must be 5% or less for DC power supplies.

SDV-SH @@@@ (Order Separately)

12345

Rated current Rated voltage Model Rated current Rated voltage Model

5 A 60 mV SDV-SH5 75 A 60 mV SDV-SH75

7.5 A SDV-SH7.5 100 A SDV-SH100

7.5 A 100 mV SDV-SH7.5 100MV 150 A SDV-SH150

10 A 60 mV SDV-SH10 200 A SDV-SH200

15 A SDV-SH15 300 A SDV-SH300

20 A SDV-SH20 500 A SDV-SH500

30 A SDV-SH30 750 A SDV-SH750

50 A SDV-SH50 1,000 A SDV-SH1000

Applicable models Socket

Type Model

SDV-F@@/-FH@T Front Connecting Socket 8PFA1

Back Connecting Socket PL08

SDV-D@@ Front Connecting Socket 14PFA

Back Connecting Socket PL15

Control power supply voltage Input

DC DC or AC (selectable)

Input voltage range

4 to 240 mV 0.2 to 12 V 10 to 300 V

24 VDC SDV-FL2 SDV-FM2 SDV-FH2

48 VDC SDV-FL3 SDV-FM3 SDV-FH3

100/110 VDC SDV-FL4 SDV-FM4 SDV-FH4

125 VDC SDV-FL5 SDV-FM5 SDV-FH5

200/220 VDC --- --- SDV-FH51

100/110 VAC SDV-FL6 SDV-FM6 SDV-FH6

120 VAC --- --- SDV-FH61

200/220 VAC SDV-FL7 SDV-FM7 SDV-FH7

240 VAC --- --- SDV-FH71

Control power supply voltage Input: DC or AC (selectable)

Input voltage range

0.2 to 12 V 10 to 300 V

24 VDC SDV-DM2 SDV-DH2

48 VDC SDV-DM3 SDV-DH3

100/110 VDC SDV-DM4 SDV-DH4

125 VDC SDV-DM5 SDV-DH5

100/110 VAC SDV-DM6 SDV-DH6

200/220 VAC SDV-DM7 SDV-DH7

240 VAC SDV-DM71 SDV-DH71

SDV

Single-function Models with Timing Function

Note: SDV-FL and SDV-FM models can also be equipped with the timing function as a special specification. Ask your OMRON representative for

details.

Specifications

Single-function Models

Overvoltage or Undervoltage Detection (Switch Selectable)

Note: Ripple is 5% max. with DC power supplies.

Dual-function Models

Overvoltage and Undervoltage Detection

Note: 1. Inquire about production of models with 120- and 240-VAC control power supply.

2. The ripple factor must be 5% or less for DC power supplies.

Control power supply voltage Input: DC or AC (selectable); input voltage range: 10 to 300 V

Operating mode

ON-delay OFF-delay Startup lock

24 VDC SDV-FH2T

48 VDC SDV-FH3T

100/110 VDC SDV-FH4T

125 VDC SDV-FH5T

200/220 VDC SDV-FH51T

100/110 VAC SDV-FH6T

120 VAC SDV-FH61T

200/220 VAC SDV-FH7T

240 VAC SDV-FH71T

Model Input voltage Selectable operating range Selectable reset value range Control power supply

SDV-FL@DC 4 to 240 mV

(4 to 12 mV, 10 to 30 mV,

20 to 60 mV, 40 to 120 mV,

80 to 240 mV)

2% to 30% (related to

operating value)

24, 48, 100/110, 125, 200/220 VDC

(see note);

100/110, 200/220/240 VAC

(50/60 Hz)

SDV-FM@DC or AC

(selectable)

0.2 to 12 V

(0.2 to 0.6 V, 0.5 to 1.5 V, 1 to 3 V,

2 to 6 V, 4 to 12 V)

SDV-FH@

SDV-FH@T

10 to 300 V

(10 to 30 V, 25 to 75 V, 50 to 150 V,

100 to 300 V)

Model Input voltage Selectable operating range Reset value Control power supply

Intermediate voltage of

dead band

Dead band

voltage

SDV-DM@DC or AC

(selectable)

0.2 to 12 V 0.2 to 0.6 V 0.02 to 0.1 V Overvoltage:

(Intermediate voltage of

dead band + dead band

voltage) – (dead band volt-

age x 2/3) min.

Undervoltage:

(Intermediate voltage of

dead band – dead band

voltage) + (dead band volt-

age x 2/3) max.

24, 48, 100/110, 125 VDC;

100/110, 200/220/240 VAC

(50/60 Hz)

0.5 to 1.5 V 0.05 to 0.25 V

1 to 3 V 0.1 to 0.5 V

2 to 6 V 0.2 to 1 V

4 to 12 V 0.4 to 2 V

SDV-DH@10 to 300 V 10 to 30 V 1 to 5 V

25 to 75 V 2.5 to 12.5 V

50 to 150 V 5 to 25 V

100 to 300 V 10 to 50 V

SDV

■Ratings

Note: The impedance value is a reference value; actual values may vary.

■Characteristics

Note: Overvoltage: Operation when voltage is changed from 80% to 120% of the operating value.

Undervoltage: Operation when voltage is changed from 120% to 80% of the operating value.

Item SDV-FL@SDV-FM@SDV-FH@/FH@TSDV-DM@SDV-DH@

Allowable continuous

input overvoltage range

±10 VDC ±150 VDC

150 VAC

±350 VDC

(±500 VDC for 1 min)

350 VAC

(500 VAC for 1 min)

±150 VDC

150 VAC

±350 VDC

(±500VDC for 1min)

350 VAC

(500 VAC for 1 min)

Input impedance 1 kΩ50 kΩ2,500 kΩ50 kΩ2,500 kΩ

Control output SPDT SPST-NO and SPST-NC

Rated load: 5 A at 220 VAC (cosφ = 1),

5 A at 24 VDC (cosφ = 1),

2 A at 220 VAC (cosφ = 0.4),

2 A at 24 VDC (L/R = 7 ms)

Max. contact voltage: 250 VAC, 125 VDC

Max. contact current: 5 A

Max. switching capacity: 1,100 VA (cosφ = 1), 120 W (cosφ = 1),

440 VA (cosφ = 0.4), 48 W (L/R = 7 ms)

Power consumption DC: 5 W max.; AC: 5 VA max.

Ambient temperature –10 to 55°C (with no icing)

Control supply voltage

(see note)

24, 48, 100/110, 125, 200/220 VDC; DC operating voltage range: 80% to 130% of control power supply

100/110/120, 200/220/240 VAC (50/60 Hz); AC operating voltage range: 85% to 110% of control power supply

Item SDV-F@@ SDV-FH@TSDV-D@@

Operating value 100% operation for voltage setting

Setting error Operating value: ±2% of operating value

(This is the ratio for the setting value.)

Reset value: ±7% of reset value

(This is the ratio for the setting value.)

±2% of intermediate voltage of dead band,

±1% of dead band voltage

Operating time 0.5 s max. (see note)

Influence of temperature 0 to 40°C:

±2% max. of operating value

(SDV-FL (operating value range: 4 to 12 mV)

±4% max. of operating value)

–10 to 0°C, 40 to 55°C:

±4% max. of operating value

(SDV-FL (operating value range: 4 to 12 mV)

±8% max. of operating value)

0 to 40°C:

±2% max. of dead band voltage

–10 to 0°C, 40 to 55°C:

±4% max. of dead band voltage

Influence of control power ±1% max. of operating value

DC operating voltage range: 80% to 130%

AC operating voltage range: 85% to 110%

±1% max. of dead band voltage

DC operating voltage range: 80% to 130%

AC operating voltage range: 85% to 110%

Influence of frequency

(Input frequency changed

from 10 to 500 Hz for AC in-

put)

±1% max. of operating value ±1% max. of dead band voltage

Influence of waveform

(For commercial frequency,

single-phase, full-wave AC

input)

±3% max. of operating value ±3% max. of dead band voltage

Insulation resistance 10 MΩ min. (at 500 VDC) between the entire electric circuitry and external case, and between the input terminal

and power terminal

Dielectric strength 2,000 VAC for 1 min between the entire electric circuitry and external case, and between the input terminal and

power terminal

Impulse withstand voltage ±1.2 x 50 μs, 4,500 V between the entire electric circuitry and external case

±1.2 x 50 μs, 3,000 V between power terminals

Vibration resistance Destruction: 10 to 25 Hz, 2-mm double amplitude (2G max.) for 2 hrs each in 3 directions

Malfunction: 16.7 Hz, 1-mm double amplitude for 10 min each in 3 directions

Shock resistance Destruction: 294 m/s2 (30G)

Malfunction: 98 m/s2 (10G)

Weight Approx. 290 g Approx. 350 g Approx. 310 g

SDV

Timing Function

Note: The time setting range when the startup lock is selected for the operating mode is approximately 1 to 30 s.

Nomenclature

Item SDV-FH@T

Setting time 0.5 to 30.0 s (see note)

Operating time accuracy ±5% FS max.

Setting error ±15% FS max.

Reset time 5 s min.

Influence of temperature ±10% FS max.

Operating mode (set via DIP switch) ON-delay, OFF-delay, Startup lock

SDV-F@/-FH@T

Location of DIP switch to

set operating modes

Setting Operating

Value

Operation Indicator (LED)

Function Sticker

Voltage Multiplying

Factor Sticker

Setting Reset Value

Setting Operating Time

Setting Intermediate

Voltage of Dead Band Setting Dead

Band Voltage

Operation Indicator

SDV-D@

The diagram on

the right shows

the SDV-FH6T

when used for

undervoltage

detection for

DC input.

Function Sticker Voltage Multiplying

Factor Sticker

Location of DIP switch to

set operating modes

The diagram above shows the

SDV-DH3 when used for AC input

in the range 100 to 300 V.

Note: The SDV-F@ is not equipped with a time setting knob.

SDV

Operation

■Timing Charts

Single-function Models

Overvoltage Detection Undervoltage Detection

Operating

value

Input

Reset value

Output relay

Input

Reset value

Operating

value

Output relay

OFF ON

OFF

Note

The reset time must be 5 s or longer to ensure accuracy of the timing operation.

Single-function Model with Timing Function

SDV-FH@T

ON-delay Overvoltage Detection

Operating

value

Input

Output relay

Setting timeSetting time Setting time

Reset value

Output relay

Input

Operating

value Reset value

Reset time

(5 s min.)

ON-delay Undervoltage Detection

Output relay

Input

Operating

value

Reset value

Reset time

(5 s min.)

Setting timeSetting time Setting time

Input

Operating

value

Output relay

Reset value

OFF

Setting time

SDV

Note: The output relays will be forced OFF from the control power supply is turned ON until the set time has expired.

OFF-delay Overvoltage Detection

OFF-delay Undervoltage Detection

Output relay

Input

Operating

value

Reset value

Reset time

(5 s min.)

Operating

value

Input

Output relay

Setting timeSetting time Setting time

Reset value

Operating

value

Input

Output relay

Setting timeSetting time Setting time

Reset value

Output relay

Input

Operating

value

Reset value

Reset time

(5 s min.)

Startup Lock

Power

Output operation

Setting time

Power

Reset time

(5 s min.)

OFF

Setting time

Dual-function Models

SDV-D

Input

Intermediate

voltage of

dead band

Dead band voltage

Undervoltage

relay

Overvoltage

relay

ONON

SDV

■Setting

(Refer to Examples of Mode Settings for details on individual models.)

Set the desired values using the DIP switch and setting knobs on the front panel.

Opening the DIP Switch Cover

Remove the cover of the compartment containing the DIP switch for various mode settings, and then set the DIP switch according to the SWITCH

SELECTION table affixed to the side of the voltage sensor.

Setting the DIP Switch

Set the DIP switch on the front panel for the required functions, operation inputs, and voltages. Set the switch to the top for ON settings and to the

bottom for OFF settings.

•Function (SDV-F): Set to either overvoltage or undervoltage detection.

•Input: Set to either AC or DC input.

•Polarity (SDV-FL@ only): Set polarity or not to specify polarity.

“8(+), 7(–)”: Use polarity as shown for pin number.

“FREE”: Do not use polarity.

•Multiplying Factor: Set the voltage scale multiplying factor for the required operating voltage setting range.

•TIMER (SDV-FH@T): Select the timing function.

Set ON-delay, OFF-delay, lock timer (start lock timer), or TIMER OFF.

If TIMER OFF is set, the timing function will not be effective, and the single-function operation will be performed.

Setting of Time (SDV-FH@T Only)

Use the time setting knob to set the desired time.

Closing the DIP Switch Cover

Attach the cover to the compartment housing the DIP switch. Select the stickers for the settings that have been made and attach them to the cover.

Setting Flowchart

Cover

Flat-blade

screwdriver

Flat-blade screwdriver

Cover

Select model based on operation and type of input.

Single-function Model Dual-function Model

Determine detection method, polarity setting, operating value,

and reset value.

Determine intermediate voltage of dead band and dead band

voltage.

Determine reset value according to dead band voltage.

Obtain the PICK UP index scale value, HOLD index scale

value, and voltage multiplying factor.

Set the knob and the DIP switch, and attach stickers.

Set the desired operating mode for the SDV-FH@T.

Obtain the BALANCE index scale value, BAND WIDTH index

scale value, and voltage multiplying factor.

Set the knob and the DIP switch, and attach stickers.

SDV

SDV-FL@

Switch Selection Table

Accessory Labels

SDV-FM@

Switch Selection Table

Accessory Labels

SDV-FH@

Switch Selection Table

Note: “NO USE” indicates that DIP switch setting is not required and

the positions of these switches are irrelevant to the operation of

the voltage sensor.

Accessory Labels

Switch

Function Under

Over

Polarity 8 (+) 7 (–)

Free

Multiplying

factor

x 4 mV →

x 10 mV →

x 20 mV →

x 40 mV →

x 80 mV →

ON ●1234 5 6

OFF

●

OVER

POL FREE

×4 mV

10 mV

20 mV

40 mV

80 mV

OVER

8 (+)

POL7 (−)

UNDER

8 (+)

POL7 (−)

UNDER

POL FREE

Switch

Function Under

Over

Input AC (20 to 500 Hz)

Multiplying

factor

x 0.2 V →

x 0.5 V →

x 1 V →

x 2 V →

x 4 V →

ON ●1234 5 6

OFF

●

OVER

INPUT DC

INPUT AC

×0.2 V

×0.5 V

1 V

2 V

4 V

OVER

UNDER

Switch

Function Under

Over

Input AC (20 to 500 Hz)

Multiplying

factor

x 10 V →

x 25 V →

x 50 V →

x 100 V →

ON ●1234 5 6

OFF

●

NO USE

(see note)

●

OVER

INPUT DC

INPUT AC

×10 V

×25 V

×50 V

100 V

OVER

UNDER

SDV

SDV-FH@T

Switch Selection Table

Note: “NO USE” indicates that DIP switch setting is not required and the positions of these switches are irrelevant to the operation of the voltage

sensor.

SDV-DM@

Switch Selection Table

Accessory Labels

SDV-DH@

Switch Selection Table

Note: “NO USE” indicates that DIP switch setting is not required and

the positions of these switches are irrelevant to the operation of

the voltage sensor.

Accessory Labels

Switch

Function Under

Over

Input AC (20 to 500 Hz)

Multiplying

factor

x 10 V →

x 25 V →

x 50 V →

x 100 V →

Timer ON-delay →

OFF-delay →

Lock timer →

Timer OFF →

Accessory Labels

OVER

INPUT DC

INPUT AC

×10 V

×25 V

×50 V

100 V

OVER

UNDER

ON ●1234 5 6 7 89 10

OFF

●

NO USE

(see note)

NO USE

(see note)

●

● ● ●

● ●

●

Switch

Input AC (20 to

500 Hz)

Multiplying

factor

x 0.2 V →

x 0.5 V →

x 1 V →

x 2 V →

x 4 V →

ON ●1234 5

OFF

●

OVER&

UNDER

OVER&

UNDER

INPUT DC

INPUT AC

×0.2 V

×0.5 V

1 V

2 V

4 V

Switch

Input AC (20 to

500 Hz)

Multiplying

factor

x 10 V →

x 25 V →

x 50 V →

x 100 V →

ON ●1234 5

OFF

●

NO USE

(see note)

●

OVER&

UNDER

OVER&

UNDER

INPUT DC

INPUT AC

×10 V

×25 V

×50 V

100 V

SDV

■Examples of Mode Setting

Example 1

Example 2

For the single-function SDV-FH6, the setting method given below would be used to detect overvol-

tages with a DC voltage input. The operating value is 15 V and the reset value is 12 V.

Step 1. To set the detection method and type of input on the DIP switch.

Turn OFF pin 1 (function) to specify overvoltage detection.

Turn OFF pin 2 (input) to specify a DC input.

Attach the OVER INPUT DC stickers.

Voltage multiplying factor setting: The voltage multiplying factor is selected according to the

maximum and minimum factors and a sticker is attached.

The calculation method is as follows:

The PICK UP index scale value is between 1.0 and 3.0, so calculate the voltage multiplying

factor for both 1.0 and 3.0.

15 V (Operating value)/1 (PICK UP index scale value) = 15 (Maximum multiplying factor)

15 V (Operating value)/3 (PICK UP index scale value) = 5 (Minimum multiplying factor)

In this example, pins 3 to 5 are turned OFF and the x10V sticker is attached.

PICK UP index scale value setting: The calculation method is as follows (X = index scale):

10 (Voltage multiplying factor) x X = 15 V (Operating value)

Therefore, X = 1.5

Turn the PICK UP knob to 1.5.

12 V (reset value) = 15 V (operating value) x (1 − Y) Therefore, Y = 0.2

Set the HOLD knob to 20 (%).

SDV-F@@

Step 3. To set the reset value (Y = HOLD index scale value): Calculate the HOLD percentage as

follows:

Step 2. To set the operating value according to the voltage multiplying factor and the PICK UP

index scale value.

For the single-function SDV-FH6T, the setting method given below would be used to detect undervol-

tages with a DC voltage input. The operating value is 20 V and the reset value is 20.4 V. An ON-delay

operation is specified and the setting time is 30 s.

Step 1. To set the detection method and type of input on the DIP switch.

Turn ON pin 1 (function) to specify undervoltage detection.

Turn OFF pin 2 (input) to specify a DC input.

Attach the UNDER INPUT DC stickers.

Step 2. To set the operating value according to the voltage multiplying factor and the PICK UP

index scale value.

Voltage multiplying factor setting: The multiplying factor is selected according to the maxi-

mum and minimum factors and a sticker is attached. The calculation method is as follows:

The PICK UP index scale value is between 1.0 and 3.0, so calculate the voltage multiplying

factor for both 1.0 and 3.0.

20 V (Operating value)/1 (PICK UP index scale value) = 20 (Maximum multiplying factor)

20 V (Operating value)/3 (PICK UP index scale value) = 6.7 (Minimum multiplying factor)

In this example, pins 3 to 5 are turned OFF and the x10V sticker is attached.

PICK UP index scale value setting: The calculation method is as follows (X = index scale):

10 (Voltage multiplying factor) x X = 20 V (Operating value)

Therefore, X = 2

Turn the PICK UP knob to 2.0.

Step 3. To set the reset value (Y = HOLD index scale value): Calculate the HOLD percentage as

follows:

20.4 V (reset value) = 20 V (operating value) x (1 + Y) Therefore, Y = 0.02

Set the HOLD knob to 2 (%).

Step 4. To set setting time and operating mode.

Set the time setting knob to 30 s and turn the pins 7 to 9 ON to specify ON-delay operation.

SDV-FH@T

SDV

Example 3

■Shunts (Order Separately)

A shunt is a resistor to convert a DC current into a DC voltage. Use

the shunt in combination with SDV-FL to detect undercurrent, reverse

current and overcurrent in DC circuits.

Note: Select a shunt whose rated current is more than 120% of the

current normally flowing in a circuit. The characteristics of the

shunt may change or fusing of a resistor element may occur if

an overload that is 1,000% of the rated current is applied.

Therefore, determine the rated current of the shunt to be used,

by taking the circuit conditions into account.

For the dual-function SDV-DH3, the setting method given below would be used to detect over and

undervoltage with an AC voltage input. The intermediate voltage of dead band is 250 V and the dead

band voltage is 20 V.

Step 1. To set the detection method and type of input on the DIP switch.

Turn ON pin 1 (input) to specify a AC input.

Attach the OVER and UNDER INPUT AC stickers.

Step 2. To set the intermediate voltage of dead band according to the BALANCE index scale

value and the voltage multiplying factor.

Voltage multiplying factor setting: The voltage multiplying factor is selected according to the

maximum and minimum factors and a sticker is attached. The calculation method is as fol-

lows:

250 V (Intermediate voltage of dead band)/1 (BALANCE index scale value)

= 250 (maximum multiplying factor)

250 V (Intermediate voltage of dead band)/3 (BALANCE index scale value)

= 83.3 (maximum multiplying factor)

In this example, pins 2 and 3 are turned OFF and pins 4 is turned ON, and the x100V sticker

is attached.

BALANCE index scale value setting: The calculation method is as follows for the BALANCE

index scale value (X = index scale):

100 (Voltage multiplying factor) x X = 250 V (intermediate voltage of dead band)

Therefore, X = 2.5

Turn the BALANCE knob to 2.5.

Step 3. To set dead band voltage according to the voltage multiplying factor and BAND WIDTH

index scale value.

BAND WIDTH index scale value setting:

Z (BAND WIDTH index scale value) x 100 V (voltage multiplying factor) = 20 V (dead band

voltage) Therefore, Z = 0.2

Set the DEAD WIDTH knob to 0.2.

Step 4. Reset value for each detection setting: Automatically set according to the dead band

voltage setting.

Reset values are calculated for overvoltage detection and undervoltage detection.

Overvoltage detection: Reset value = (250 V + 20 V) − (20 V x 2/3) = 256.7 min.

Undervoltage detection: Reset value = (250 V − 20 V) + (20 V x 2/3) = 243.3 max.

SDV-D@@

The BALANCE index scale value is between 1.0 and 3.0, so calculate the voltage multiply-

ing factor for both 1.0 and 3.0.

Output voltage (mV)

Input current (A)

Characteristics

SDV-SH5A (Rated Current: 5 A)

Shunt rated

at 60 mV

SDV

■Application Example

Current Detection Using the Shunt (SDV-FL)

Voltage Detection (SDV-FM/FH/FH@T/-DM/-DH)

Overload Detection (A) Overload Detection (B)

Example: Overload detection in a distribution switch

board installed in a power substation.

Example: Overload detection in equipment such as a motor in a

rolling mill when the polarity of the applied voltage to

the motor is reversed.

DC power

supply for

distribution

board

SDV-SH

shunt

SDV-FL

(with or without polarity)

Distribution

switchboard

SDV-SH

shunt

DC motor

SDV-FL

(without polarity)

(−)

(+)

(+) (−)

(−) (+)

Power

supply

Reverse Current Detection (A) Reverse Current Detection (B)

Example: Detection of an output current from a transmitter on

a control panel.

SDV-FL

(with or without polarity)

Power supply

for transmitter

4 to 20mA

Quantity of

low, airflow,

wattage, etc.

Transmitter

10 Ω or more

(−)

(+)

SDV-SH

shunt

DC motor

SDV-FL

(with polarity)

(−)

(+)

DC power

supply

Example:

Detection when a DC motor is used

as a generator (or a generator is

used as a motor).

Voltage Regulation Operation Lock Due to Voltage Drop (Alarm)

Example: Voltage regulation of a power supply unit in the dis-

tribution switchboard installed in a power substation.

Example: Function lock due to voltage drop in a machine or

equipment (alarm).

Thyristor

power

supply

Distribu-

tion

switch

board

Command

signal for

regulation

3 dia.

Machine

or equip-

ment

Command

signal for

operation

lock

SDV-FH/SDV-FH@T

with ON-delay operation

(undervoltage detection)

SDV-DH

(+)

(−)

SDV

Non-utility generator

Detection of

power failure

Engine

Drive command

(Starts/Stop)

Exciter

Voltage regula-

tion (rotation

control)

Power supply

Detection of power failure or trans-

former trouble (for the DC lighting

command in emergency illumination)

Detection of battery

overdischarge

Distribution board for general illumination

Detection of partial power

failure (for the lighting

command in emergency

illumination)

Distribution board for

emergency illumination Emergency illumination

output

SDV-FH (undervol-

tage detection)

SDV-FH (undervoltage

detection)

SDV-FH/SDV-FH@T

with ON-delay operation

(undervoltage detection)

SDV-FH (undervoltage

detection)

Emergency Power Supply (e.g. Standard Power Receiving/Distributing Facility)

SDV-DH

SDV

Three-phase AC Current Detection Using Current Converter

Current Converters (Order Separately)

Voltage Monitoring in Rectifiers (Chargers) with ON-delay Operation

Example: To detect only overvoltage and not detect voltages for instantaneous load changes (ON/OFF).

Example: Machine motor control, overload detection,

undercurrent detection.

SET Current Converter

SDV-DH

SDV-FH

SDV-FH@T

SDV-FM

Model Current range

SET-3A 1 to 80 A

SET-3B 64 to 160 A

Three-phase AC Current Detection with Startup Lock Operation

(When Using Same Power Supply for Motor and Control Power Supply)

SET Current Converter

Control power supply

SDV-FH@T

Load

SDV-FH@T

undervoltage detection

Rectifier

SDV-FH@T

overvoltage detection

Note: Detection of excessive or insufficient charge in rectifiers (chargers).

SDV

■Q&A

Q: What is necessary to detect undervoltages when using the same power supply for the input voltage and the control

power supply?

A: The NO contact of the output relay is used for undervoltage detection. Even if the control voltage drops to 85% of

the rated voltage (AC power), the operation of the relay can be maintained. Set the mode setting on the DIP switch

to overvoltage detection and set the reset value to the value to be detected. Set the operating value of the SDV to

a value higher than the reset value.

Q: Will the SDV be damaged if the input setting (AC/DC) is incorrect. If not, what will happen?

A: The SDV will not be damaged, but the operating value and reset value will not be accurate. These values will be

about 10% less than the set values if DC is input for an AC setting and about 10% off to the positive side if AC is

input for a DC setting.

Q: Can the negative pole of a DC voltage be input to the SDV?

A: Yes. An absolute rectifier circuit is used in the SDV-F to enable negative pole input. The SDV-FL has a polarity

setting, which can be set to (+)(–) to disable operation with negative voltages. Positive/Negative settings cannot

be used for the dual-function SDV-D even if the intermediate voltage of dead band is set to 0. Negative inputs can-

not be used for the SDV-D.

Q: Is instantaneous detection faster than 0.5 s possible?

A: Use the S87A Power Interruption Detector for instantaneous detection (10 ms or 20 ms).

SDV-F (undervoltage detection)

Load

SDV

Dimensions

Note: All units are in millimeters unless otherwise indicated.

■Main Body

■Shunts

SDV-F@@/SDV-FH@T

SDV-D@@

Connecting Socket

3.5

60 89

100

7291

8.5

8PFA1 (order separately)

SDV-F

119

PL08 (order separately)

100

SDV-F

89 7

100

8.5

3.5

6079

14PFA (order separately)

SDV-D

128.5

PL15 (order separately)

100

SDV-D

Model A B C D E F G

SDV-SH75 140 120 25 10.5 6 18 36

SDV-SH100 140 120 25 10.5 6 18 36

SDV-SH150 140 120 25 10.5 6 18 43

SDV-SH200 140 120 25 10.5 6 18 43

SDV-SH5 to SDV-SH50 (60-mV Rating)

Current terminal: M6 screw

Voltage terminal: M4 screw

SDV-SH75 to SDV-SH200 (60-mV Rating)

Current terminal: M8 screw

Voltage terminal: M4 screw

10.5 dia.

5.5

dia. 5.5

dia.

140

120

SDV

Note: Inquire about models with a rated current of 1,500 A or larger.

■Accessories (Order Separately)

Front Connecting Socket

Model A B C D E Resistor

SDV-

SH300

130 30 110 4 36 4

SDV-

SH500

160 40 120 6 41 5

SDV-SH300/-SH500 (60-mV Rating)

Current terminal: M10 screw (SDV-SH300),

M12 screw (SDV-SH500)

Voltage terminal: M4 screw

Model A B C D E

SDV-

SH750

175 45 130 15 30

SDV-

SH1000

175 60 135 18 30

SDV-SH750/-SH1000 (60-mV Rating)

Current terminal: M12 screw

Voltage terminal: M5 screw

8PFA1

Terminal Arrangement

(Top View)

Mounting Holes

Two, M4 or 4.5-dia. holes

Eight, M3.5 x 7

sems

Two, 4.5-dia.

holes

93 max.

51 max.

24 max.

130 max.

14PFA

Fourteen,

M3.5 x 7 sems

81 max.

72 max.

Two,

4.5-dia.

holes

33.5 max.

118 max.

Two, M4 or 4.5-dia. holes

Terminal Arrangement

(Top View)

Mounting Holes

SDV

Back Connecting Socket (Solder Terminal)

PL08

Terminal Arrangement

(Bottom View)

Mounting Holes

PL15

Terminal Arrangement

(Bottom View)

Mounting Holes

Two, 3.5-dia. or

two, M3 socket

mounting holes

50.5 max.

35 max.

30 dia.

Approx. 20.5

Two, 2-dia. holes

Two, M3 or two, 3.5-dia.

voltage sensor mounting

holes

Two, M3 or Two, 3.5-dia.

socket mounting holes

42-dia. hole

22 max.

66 max. 41 max.

Two, 2-dia. holes

31-dia.

hole

45 max.

Mounting Track

PFP-100N

PFP-50N

4.5

15 25 25 25 25

10 10

1,000 (500)*

7.3+0.15

35+0.3 27+0.15

15 (5)*

*PFP-50N

4.5

15 25 25 25 25 15

10 10

1,000

35+0.3 27 24

29.2

1 1.5

PFP-100N2

End Plates

PFP-M

11.5

M4 x 8 pan

head screw

6.2 1.8

135.5 35.3

1.8

1.3

4.8

M4 spring

washer 5

44.3 34.8

16.5

Spacers

PFP-S

SDV

Installation

■Internal Circuit

Input and power supply circuits are electrically isolated as protection against mutual interference.

SDV-F@@/SDV-FH@T

SDV-D

Note: 1. There is no polarity setting for the SDV-FM or SDV-FH/-FH@T.

2. There is no power supply polarity setting when using a DC control power supply for the SDV.

3. The polarity selection switch (SW2) is on the SDV-FL.

4. The AC/DC switch (SW2) is on the SDV-FM and SDV-FH/-FH@T.

Note: 1. There is no power supply polarity setting when using a DC control power supply for the SDV.

2. There is no polarity setting for DC inputs.

voltage circuit

Reference

Range selector switches

Polarity selector switch

(SW2)

(see note 3)

Power

supply

circuit

Power

supply

circuit

each

circuit Chopper

circuit

Overvoltage/

Undervoltage

selector switch

SW1

Output relay

Comparator

circuit

Power circuit

Inverter circuit

Amplifier circuit

Releasing value

setting circuit

Timer time

setting circuit

Buffer circuit

Absolute value

rectifier circuit

Operating value

setting circuit

AC/DC selector

switch SW2

(see note 4)

Startup lock

reference

voltage circuit

Inverter circuit

Comparator

circuit

Buffer circuit

DC Power supply circuit

AC Power supply circuit

Input

Quick charge/

discharge circuit

each

circuit

Reference

voltage circuit

Power

supply

circuit

Power

supply

circuit

each

circuit

each

circuit

Dear band

setting circuit

Range selector switches

AC/DC selector

switch SW1

Amplifier circuit

Chopper

circuit

AC Power supply circuit

DC Power supply circuit

Smoothing

circuit

Power circuit

voltage circuit

Reference

Power circuit

voltage circuit

Reference

Input

Output relay for

overvoltage

detection

Addition circuit

Comparator

circuit(High)

Power

supply

Power

supply

Output relay for

overvoltage

detection

Output relay for

undervoltage

detection

Comparator

circuit(Low)

Absolute value

rectifier circuit

Note: The SDV-FH@T contains

the circuit outlined with the

dotted line.

SW6

SW7

SW9

SW5 SW4 SW3

X/c

SW8

Power

supply

Power

supply

SW5 SW4 SW3 SW2

XL/a

XL/b

XH/b

XH/a

SW1

Smoothing

circuit

SDV

Safety Precautions

Approximately 0.5 s is required for operation. When confirming the

operating value, gradually change the input voltage while checking

the value.

Power supply voltage fluctuations and the ambient operating temper-

ature must be maintained within the allowable ranges. Be particularly

careful not to apply an overvoltage beyond the specified range for the

voltage detection.

Do not use the SDV in locations subject to corrosive or explosive

gases.

The SDV cannot be used to detect momentary power interruptions

because of its response time. Use the S87A to detect momentary

power interruptions.

An SDV cannot be used with a circuit containing thyristors, or VVVF

inverters, because these elements can change the output waveform

to the point that the SDV will malfunction.

Mounting

When mounting with the PL08 or PL15 Back Connection Socket,

insert the Socket into a 1- to 4-mm panel from the back and secure it

with screws. Do not mount the SDV until the Socket has been

mounted firmly. Be sure that the key groove on the Socket is

mounted on the bottom, and also secure the SDV to the panel with

screws.

When mounting with the 8PFA or 14PFA Back Connection Socket,

insert the SDV into the Socket and secure it with the hooks. Leave

approximately 30 mm or more between Sockets to allow enough

space for the hooks.

When mounting more than one SDV, allow at least 30 mm or more

between them.

S87A Power Interruption Detector

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Read and Understand This Catalog

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or

comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)

from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR

FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS

DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS

IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT

LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS

OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT

SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's

application or use of the products.

At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the

products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,

machine, system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible

uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:



Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.



Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,

safety equipment, and installations subject to separate industry or government regulations.



Systems, machines, and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE

SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND

INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons.

It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or

establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual

specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the

result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON

Warranty and Limitations of Liability.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,

typographical, or proofreading errors, or omissions.

2011.12

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/