Document 864 Flyback Transformers * Designed for input range of 10 - 14 V. * 1500 Vrms isolation from primary and bias to secondary; 500 Vrms isolation from primary to bias, tested for one minute * The bias winding provides power to the chipset Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 3.9 to 4.1 g Ambient temperature -40C to +85C Storage temperature Component: -40C to +85C. Packaging: -40C to +80C Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250 per 13 reel Plastic tape: 32 mm wide, 0.5 mm thick, 20 mm pocket spacing, 11.2 mm pocket depth PCB washing Only pure water or alcohol recommended Inductance Part at 0 A2 1 number 10% (H) GA3430-BL_ 25.0 GA3431-BL_ 25.0 Inductance at Ipk3 min (H) 22.5 22.5 DCR max (mOhms)4 pri sec bias 90 15 95 90 5.0 70 Leakage inductance Turns ratio6 max (H)5 pri : sec : bias 0.685 5:1:1 0.945 7:1:1 1. When ordering, please specify packaging code: 0.450 max 11,43 0.004 /0,10 0.041 1,05 0.600 max 15,24 0.413 10,50 4 2 0.024 0,60 8 1 0.080 2,03 0.460 11,68 0.050 1,27 0.50 max 12,7 1 4 Pri Output7 5.0 V, 1.0 A 3.3 V, 1.5 A Dot above pin1 GA3431-BLD Packaging: D = 13 machine-ready reel. EIA-481 embossed plastic tape (250 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 250 kHz, 0.3 Vrms, 0 Adc. 3. Ipk is peak primary current drawn at minimum input voltage. 4. DCR for the secondary is per winding. 5. Leakage inductance measured between pins 3 and 4 with all secondary pins shorted. 6. Turns ratio is with the secondary windings connected in parallel. 7. Output is with the secondary windings connected in parallel. Bias winding output: 5.0 V, 20 mA (GA3430); 3.3 V, 20 mA (GA3431). 8. Electrical specifications at 25C. Refer to Doc 362 "Soldering Surface Mount Components" before soldering. 3 Input voltage (V) 10 - 14 10 - 14 Ipk3 (A) 2.1 2.1 5 6 5 0.098 2,50 Recommended 0.098 2,50 Land Pattern Sec 7 8 Dimensions are in inches mm Bias 1 Secondary windings to be connected in parallel on PC board Specifications subject to change without notice. Please check our website for latest information. (c) Coilcraft, Inc. 2010 Document 864 Revised 05/04/10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Coilcraft: GA3431-BLB GA3430-BLD GA3430-BLB GA3431-BLD