PRELIMINARY INFORMATION ICS627-01 HDTV Set-Top Clock Source Description Features The ICS627-01 is a low cost, low jitter, high performance clock synthesizer which can generate frequencies required for HDTV receivers and settop boxes. Using ICS's patented analog/digital Phase-Locked Loop (PLL) techniques, the device uses an inexpensive fundamental 27 MHz crystal input to produce low jitter HDTV pixel clocks. It has a separate input for a 1001/1000 or 2(1001/1000) conversion from a 13.5 MHz, 27 MHz or 54 MHz input. * Packaged in 28 pin SSOP (QSOP) * HDTV frequencies of 74.25 and 74.175824 MHz * Provides selectable B clock for 27.027 MHz or other 1001/1000 * Uses a fundamental 27 MHz crystal or clock input * All frequencies are generated exactly (zero ppm synthesis error) * Full CMOS output swings with 12 mA output drive capability at TTL levels * Advanced, low power, sub-micron CMOS process * 3.3 V 5% operating supply Block Diagram VDD CLKIN x1001/1000 PLL SB SA2:0 GND 6 PLL Clock Synthesis Circuitry Output Buffer CLKB Output Buffer CLKA Output Buffer CLKC (54 MHz) Output Buffer CLKC/2 (27 MHz) Output Buffer REFOUT (27 MHz) /2 X1/ICLK 27.0 MHz crystal or X2 clock input MDS 627-01 B Crystal Oscillator 1 Revision 051600 Integrated Circuit Systems, Inc. * 525 Race Street * San Jose *CA*95126*(408) 295-9800tel * www.icst.com PRELIMINARY INFORMATION ICS627-01 HDTV Set-Top Clock Source Pin Assignment SA2 X2 X1 VDD VDD CLKIN VDD VDD VDD GND GND CLKC/2 CLKC CLKB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CLKA/CLKC Select Table (MHz) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 SA2 SA0 SA0 REFOUT GND CLKA VDD GND GND GND GND SB SA1 SA1 SA2 SA1 SA0 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Input 27.0 27.0 27.0 27.0 TEST 27.0 TEST 27.0 CLKA 108.0 74.175824* 54.0 74.25* CLKC 54.0 TEST 54.0 54.0 CLKC/2 27.0 TEST 27.0 27.0 74.175824 54.0 27.0 74.250 54.0 27.0 * These selections are recommended for the lowest jitter CLKB Select Table (MHz) SB 0 1 CLKIN 13.5 27 - 54 CLKB 27.027 27.027 - 54.054 Multiplier 2002/1000 1001/1000 0 = connect directly to GND 1 = connect directl to VDD Pin Descriptions Number Name 1, 28 SA2 2 X2 3 X1/ICLK 4, 5, 7-9, 22 VDD 6 CLKIN 10, 11, 18, 19 GND 12 CLKC/2 13 CLKC 14 CLKB 15, 16 SA1 17 SB 20, 21, 24 GND 23 CLKA 25 REFOUT 26, 27 SA0 Type I XO XI P CI P O O O I I P O O I Description Pins 1, 28 should be connected together. Selects CLKA and CLKC frequencies. Internal p-u. Connect to a fundamental 27.0 MHz crystal or leave unconnected for clock. Connect to a fundamental 27.0 MHz crystal or clock input. Connect to 3.3V. Clock input to produce 1001/1000 or 2(1001/1000) at CLKB. See table above. Connect to ground. C Clock output divided-by-2. See table above. C Clock output. See above table. B Clock output. See above table. Pins 15, 16 should be connected together. Selects CLKA and CLKC frequencies. Internal p-u. B Clock Select. Selects CLKB frequency. See above table. Internal pull-up. Connect to ground. A Clock output. See above table. 27 MHz Reference Output. Pins 26, 27 should be connected together. Selects CLKA and CLKC frequencies. Internal p-u. Key: I = Input; O = output; P = power supply connection; XI, XO = crystal connections; CI = clock input MDS 627-01 B 2 Revision 051600 Integrated Circuit Systems, Inc. * 525 Race Street * San Jose *CA*95126*(408) 295-9800tel * www.icst.com PRELIMINARY INFORMATION ICS627-01 HDTV Set-Top Clock Source Electrical Specifications Parameter Conditions Minimum Typical Maximum Units 7 VDD+0.5 70 260 150 V V C C C 3.45 V V V V V V V V mA mA pF ppm ABSOLUTE MAXIMUM RATINGS (n note 1) Supply voltage, VDD Inputs and Clock Outputs Ambient Operating Temperature Soldering Temperature Storage temperature Referenced to GND Referenced to GND -0.5 0 Max of 10 seconds -65 DC CHARACTERISTICS (VDD = 3.3V V unless noted) Operating Voltage, VDD Input High Voltage, VIH Input Low Voltage, VIL Input High Voltage, VIH, ICLK and CLKIN Input Low Voltage, VIL, ICLK and CLKIN Output High Voltage, VOH Output Low Voltage, VOL Output High Voltage, VOH, CMOS level Operating Supply Current, IDD Short Circuit Current Input Capacitance Frequency synthesis error 3.15 2 3.30 0.8 (VDD/2)+1 IOH=-12mA IOL=12mA IOH=-8mA No Load, note 2 Each output VDD/2 VDD/2 (VDD/2)-1 2.4 0.4 VDD-0.4 TBD 50 7 All clocks 0 AC CHARACTERISTICS (VDD = 3.3V V unless noted) Input Frequency Output Clock Rise Time Output Clock Fall Time Output Clock Duty Cycle Maximum Absolute Jitter, short term Notes: 27.0 0.8 to 2.0V 2.0 to 0.8V At VDD/2 1.5 1.5 60 40 TBD MHz ns ns % ps 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. With all clocks at highest MHz. External Components The ICS627-01 requires a minimum number of external components for proper operation. Use a low inductance ground plane, connect all GNDs to this. Connect 0.01F decoupling caps across pins 5 and 10, 8 and 10, and 22 and 20, as close to the ICS627-01 as possible. A series termination resistor of 33 may be used for each clock output. The 27.000 MHz crystal must be connected as close to the chip as possible. The crystal should be a fundamental mode, parallel resonant. Crystal capacitors should be connected from pins X1 to ground and X2 to ground. The value of these capacitors is given by the following equation, where CL is the crystal load capacitance: Crystal caps (pF) = (CL-6) x 2. So for a crystal with 16pF load capacitance, two 20pF caps should be used. If a clock input is used, drive it into X1 and leave X2 unconnected. MDS 627-01 B 3 Revision 051600 Integrated Circuit Systems, Inc. * 525 Race Street * San Jose *CA*95126*(408) 295-9800tel * www.icst.com PRELIMINARY INFORMATION ICS627-01 HDTV Set-Top Clock Source Package Outline and Package Dimensions (For current dimensional specifications, see JEDEC Publication No. 95.) 28 pin SSOP E1 INDEX AREA 1 Symbol A A1 b c D e E E1 L E 2 D e Millim meters Min Max 1.35 1.75 0.10 0.25 0.20 0.30 0.19 0.25 9.80 10.01 0.635 BSC 5.79 6.20 3.81 3.99 0.41 1.27 A c A1 Inchees Min Max 0.053 0.069 0.004 0.010 0.008 0.012 0.007 0.010 0.386 0.394 .025 BSSC 0.228 0.244 0.150 0.157 0.016 0.050 b L Ordering Information Part/Order Number ICS627R-01 ICS627R-01T Marking ICS627R-01 ICS627R-01 Shipping packaging tubes tape and reel Package Temperature 28 pin SSOP (QSOP) 0-70 C 28 pin SSOP (QSOP) 0-70 C While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. MDS 627-01 B 4 Revision 051600 Integrated Circuit Systems, Inc. * 525 Race Street * San Jose *CA*95126*(408) 295-9800tel * www.icst.com