SPEC.No.MIS-DG60B28A SPECIFICATION FOR MAGNETIC CARD READER ( Manual Insertion and 2 Sensors type ) Z U - M 2 1 2 1 S 3 5 2 MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD. MATSUSHITA INDUSTRIAL EQUIPMENT CO., LTD. OSAKA JAPAN CONTENTS 1. INTRODUCTION -------------------------------------------------------------- 1 2 PRODUCT NAME -------------------------------------------------------------- 1 3 FUNCTION ------------------------------------------------------------------- 1 4 EQUIPMENT SPECIFICATION ---------------------------------------------- 1 5 BASIC FEATURES ----------------------------------------------------------- 1 6CARD STANDARD ----------------------------------------------------------- 2 7CIRCUIT CONSTRUCTION ------------------------------------------------- 3 8ENVIRONMENTAL CHARACTERISTICS 9UNIT LIFE AND RELIABILITY -------------------------------- 5 ---------------------------------------------- 6 10GUARANTEE ---------------------------------------------------------- 6 11MAINTENANCE ---------------------------------------------------------- 6 12CAUTION ON THE USE 13APPEARANCE ------------------------------------------------ 6 ----------------------------------------------------------- 8 1. INTRODUCTION This specification describes about manual Insertion type magnetic card reader, featuring small size, light weight and high performance which enable to read card data encoded by following ISO 2 standard. 2. PRODUCT NAME 2.1 Product Name 2.2 Model No. 3. Manual Insertion type magnetic card reader ZU-M2121S352 FUNCTION 3.1 Card operation 3.2 Read/Write 3.3 Read direction 4. Insertion & Ejection Read only Insertion EQUIPMENT SPECIFICATION 4.1 Out dimension 4.2 Mass (W) 102 mm x (D) 100 mm x (H) 26 mm Approx. 55 g 4.3 Supplied voltage (1) Supplied voltage DC 5 V 0.5 V / Ripple (Less than 50 mVp~p) (2) Current consumption TYP. 20 mA, MAX.25 mA (3) Absolute maximum applied voltage +7 VDC 4.4 Connector IRISO Electronics Corporation 4.5 Environment requirement 4.6 Material of bezel 5. IMSA-9204B-2-13Z080-T (Refer to 7.5) At indoor Conductive material BASIC FEATURES 5.1 Card operating speed 10 cm/sec ~ 120 cm/sec 5.2 Magnetic head (1) Numbers of channel (2) Core width (3) Core material 1 1.5 mm Permalloy -1- 6.CARD STANDARD 6.1 Card standard ISO2 Card Standard Track 2nd Recording density Recording capacity Recording method 6.2 75 BPI 23 Characters (5bit code) F2F Location of tracks ISO (2nd trackISO 7810, ISO 7811 Coercive force(Hc) :2.4x10 A/m ~2.4x10 A/m (300 Oe ~ 3000 Oe) 85.47 85.72 7.44 0.51 (Track1, 2) 7.44 1.0 (Track 3) 5.66 max. 8.46 8.97 8.97 8.46 11.76 12.27 12.52 12.01 15.32 15.82 Track1 Track2 Track3 Mag stripe 53.92 54.18 center line of first data bit (Unit : mm) 0.68 ~ 0.84 Figure 6.2 Location of Tracks -2- 7. CIRCUIT CONSTRUCTION 7.1 Block diagram Sensor1 Sensor2 A Card detection Circuit ZU-M2121S Note) Output signal: 35* F2F /CLD1 Magnetic M Decoding Head P /CLD2 /CLD /CLD /RCL /RCL ISO /RDT /RDT + 5VDC circuit GND Fig 7.1 Block diagram 7.2 Interface requirement (1) Signal Level (2) Signal Logic CMOS level Low active (3) Connection condition CMOS(MN6543S) 74HC Equivalent (Card Reader side) (System side) Fig 7.2 Connection of output circuit (4) Output voltage Table 7.2 Output voltage Min(V) Max(V) Conditions H level "0" 4.0 Vcc I = -1.0mA L level "1" - 0.4 I = -3- 4.0mA 7.3 Explanation of input/output signal Input/output signals are /CLD1, /CLD2, /CLD, /RCL, /RDT and effective operation mode for each of these signals shall be "L" level for all. (1) /CLD1 (CARD LOAD) The /CLD line will be Low when a Magnetic Card inserts in the Magnetic Card Reader. The /CLD line will be High at all other times. (2) /CLD2 (CARD LOAD) The /CLD line will be Low when a Magnetic Card is inserted in the end (3) /CLD(CARD LOAD) of Magnetic Card Reader. The /CLD line will be High at all other times. When the /CLD line will be Low when a encorded Magnetic Card Reader,and when a encoded Magnetic Card inserts in the end of Magnetic Card Reader the /CLD line will be High. (4) /RCL(READ CLOCK) This is used to sample the data line by it's falling edges. The time (5) /RDT(READ DATA) relationship of the clock with respect to the order signals is shown in Figure 7.4 The moment /RCL change from High to Low ; /RDT is "1" when the /RDT line is Low , and /RDT is "0" when the /RDT line is High. 7.4 Output signal timing chart Detail the /RCL & /RDT timing chart t3: 75BPI AE 9.5S t4: 75BPI AE 19.0S Fig 7.4 Timing chart When the jitter of the magnetic head output is 0% , the following equation is satisfied. T=T1=T2=T3 , t1=t2 -5- T(sec)= 7.5 2.54 cm/inch x Recording density (BPI) Terminal No. of connector (1) Maker : IRISO Electronics Corporation (2) Model No: IMSA-9204B-2-13Z080-T (3) Pin No. & Signal Name (Card reader side) Connector Signal Pin No. Name 1 Card speed(cm/sec) Connector Pin No. Signal Name 1 /RDT 2 NC 3 /RCL 4 NC 5 /CLD1 6 NC 7 /CLD2 8 9 +5VDC 10 GND 11 NC 12 NC 13 /CLD 14 NC (Note) : Make sure to use the connection cable of less than 300 mm length for the card reader. 8. ENVIRONMENTAL CHARACTERISTICS 8.1 Operating temperature Range -20 ~ 60 8.2 Operating humidity Range 10 % ~ 90 % RH (No condensation allowed) 8.3 Storage temperature Range -30 ~ 70 8.4 Storage humidity Range 10 % ~ 95 % RH (No condensation allowed) z *Place the card reader in the standard environment (temperature: 20 5 , humidity: 35 % ~ 60 %RH). z Leave it for 12 hours, and measure the functions. Make sure no abnormality is found. 8.5 Vibration Vibration sweep 10 H/z ~ 50 H/z, 10 m/s2, 0.5 oct/min 8.6 Shock durability X,Y,Z directions 294 m/s2(30 G) 8.7 Others Make sure any source of noise that may deteriorate the characteristics of the card reader is not present around the card reader. -5- 9. UNIT LIFE AND RELIABILITY 9.1 Life Magnetic head 300,000 times pass (conditions) In a clean office room. In damp or dirty atmosphere, the life may be 1/3 to 1/5 of the above figure. 9.2 Error rate Less than 0.1 % (conditions) This error rate is obtained when a new normal card (data"1010") is horizontally passed at the standard speed (30 cm/sec ~ 60cm/sec) by manual operatrion in the clean environment at delivery from our company. 10. GUARANTEE If defects should occur within one year after the delivery of the card reader due to improper material or bad workmanship, the defective parts shall be replaced or repaired, free of charge. 11. MAINTENANCE Because of difficulty in changing components on the P.C Board, replacement of whole unit is recommended for service and maintenance. 12. CAUTIONS ON THE USE Please be noted that we do not guarantee proper performance of the card reader if it is used other than the indicated specification range. 12.1 At the installation (1)Do not drop or bump anything against a card reader. Otherwise, failure may be the result. (2) Do not touch the P.C.B. with bear hands. (3) Be sure to install on a flat surface so as to prevent any force to be applied to the Card reader at the installation. (4) Do not drop or bump anything against a card reader. Otherwise, failure may be the result. (5) The card reader should avoid installation of the following environment. Watery, humid or dusty place. Near machines which generate magnetic field or inducted noise. (Printer ,LED display, CRT etc.) Place which gets direct sunlight. -6- 12.2 At the use (1) Be sure to use a card which conforms ISO standard. Coercive force of the applied card should be 2.4x104 A/m ~ 2.4x105 A/m (300 Oe ~ 3000 Oe) of ISO standard. (2) Card operation speed should be within the specification range. Forced stop or change of speed during the card operation may cause a read error. Appropriate speed to maintain stable operation is 30 cm/sec ~ 60 cm/sec. (3) Store the card with caution to prevent dirt, scratch and distortion. Especially, no foreign matter shall be stuck on the magnetic stripe surface. Use of such card may result in a read error. (4) Insert a cleaning card and clean the head periodically to prevent wearing of the magnetic head. Head cleaning using the cleaning card should be performed about once a week if the room is not dusty. (5) Depends on installation environment (incorporation condition) or operation condition, external noise or electrostatics and so on may affect the machine, and which may cause an error or a wrong operation. Check the level of noise resistance and electrostatic resistance of your factory before using the card reader. -7- 13. APPEARANCE -8-