DEMO MANUAL DC1710A-C LTC5592 Dual 1.6GHz to 2.7GHz High Dynamic Range Downconverting Mixer Description Demonstration circuit 1710A-C is a dual 1.6GHz to 2.7GHz high dynamic range downconverting mixer featuring the LTC(R)5592. The LTC5592 is part of a family of dualchannel high dynamic range, high gain downconverting mixers covering the 600MHz to 4.5GHz frequency range. The demo circuit 1710A-C and the LTC5592 are optimized for 1.6GHz to 2.7GHz RF applications. The LO frequency must fall within the 1.7GHz to 2.5GHz range for optimum performance. A typical application is a LTE or WiMAX receiver with a 2.3GHz to 2.7GHz RF input and low side LO. The LTC5592 is designed for 3.3V operation, however the IF amplifiers can be powered by 5V for the highest P1dB. A low current mode is provided for power savings, and each of the mixer channels has independent shutdown control. The LTC5592's high conversion gain and high dynamic range enable the use of lossy IF filters in high-selective receiver designs, while minimizing the total solution cost, board space and system-level variation. High Dynamic Range Dual Downconverting Mixer Family DEMO # IC PART # RF RANGE LO RANGE DC1710A-A LTC5590 600MHz to 1.7GHz 700MHz to 1.5GHz DC1710A-B LTC5591 1.3GHz to 2.3GHz 1.4GHz to 2.1GHz DC1710A-C LTC5592 1.6GHz to 2.7GHz 1.7GHz to 2.5GHz DC1710A-D LTC5593 2.3GHz to 4.5GHz 2.1GHz to 4.2GHz Design files for this circuit board are available at http://www.linear.com/demo L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Performance Summary TC = 25C, VCC = VCCIF = 3.3V, ENA = ENB = High, ISEL = Low, PLO = 0dBm, PRF = -3dBm (f = 2MHz for two-tone IIP3 tests), unless otherwise noted. (Note 1) PARAMETER CONDITIONS VALUE UNITS VCC Supply Voltage Range 3.1 to 3.5 V VCCIF Supply Voltage Range 3.1 to 5.3 V Total Supply Current (VCC + VCCIF), Normal Power Mode Both Mixer Channels Enabled 401 mA Total Supply Current (VCC + VCCIF), Low Power Mode Both Mixer Channels Enabled, ISEL = High 252 mA Total Supply Current During Shutdown ENA = ENB = Low 500 A ENA, ENB Input High Voltage (Channel Enabled) >2.5 V ENA, ENB Input Low Voltage (Channel Disabled) <0.3 V ENA, ENB Input Current -20 to 30 A ISEL Input High Voltage (Low Power Mode) >2.5 V ISEL Input Low Voltage (Normal Power Mode) <0.3 V -20 to 30 A ISEL Input Current -0.3V to VCC + 0.3V -0.3V to VCC + 0.3V dc1710acf 1 DEMO MANUAL DC1710A-C PERFORMANCE SUMMARY TC = 25C, VCC = VCCIF = 3.3V, ENA = ENB = High, ISEL = Low, PLO = 0dBm, PRF = -3dBm (f = 2MHz for two-tone IIP3 tests), unless otherwise noted. (Note 1) PARAMETER CONDITIONS LO Input Frequency Range VALUE 1700 to 2500 LO Input Return Loss Z0 = 50, fLO = 1700MHz to 2500MHz LO Input Power Range fLO = 1700MHz to 2500MHz RF Input Frequency Range Low Side LO High Side LO RF Input Return Loss Z0 = 50, fRF = 1600MHz to 2700MHz IF Output Frequency IF Output Return Loss >17 UNITS MHz dB -4 to 6 dBm 1900 to 2700 1600 to 2300 MHz MHz >13 dB Can be re-matched for other frequencies 190 MHz Z0 = 50 >12 dB LO to RF Leakage fLO = 1700MHz to 2500MHz < -34 dBm LO to IF Leakage fLO = 1700MHz to 2500MHz < -37 dBm RF to LO Isolation fRF = 1600MHz to 2700MHz >57 dB RF to IF Isolation fRF = 1600MHz to 2700MHz >37 dB Channel-to-Channel Isolation fRF = 1600MHz to 2700MHz >47 dB Low Side LO Downmixer Application: ISEL = Low, RF = 1900MHz to 2700MHz, IF = 190MHz, fLO = fRF - fIF Conversion Gain RF = 1950MHz RF = 2350MHz RF = 2550MHz 9.5 8.3 8.1 dB dB dB Input 3rd Order Intercept RF = 1950MHz RF = 2350MHz RF = 2550MHz 26.3 27.3 26.3 dBm dBm dBm SSB Noise Figure RF = 1950MHz RF = 2350MHz RF = 2550MHz 9.4 9.8 9.9 dB dB dB SSB Noise Figure Under Blocking fRF = 2400MHz, fLO = 2210MHz, fBLOCK = 2500MHz, PBLOCK = 5dBm PBLOCK = 10dBm 15.3 21.2 dB dB 2RF - 2LO Output Spurious Product (fRF = fLO + fIF/2) fRF = 2255MHz at -10dBm, fLO = 2160MHz, fIF = 190MHz -68 dBc 3RF - 3LO Output Spurious Product (fRF = fLO + fIF/3) fRF = 2223.33MHz at -10dBm, fLO = 2160MHz, fIF = 190MHz -74 dBc Input 1dB Compression fRF = 2350MHz, VCCIF = 3.3V fRF = 2350MHz, VCCIF = 5V 11 14.6 dBm dBm Low Power Mode, Low Side LO Downmixer Application: ISEL = High, RF = 1900MHz to 2700MHz, IF = 190MHz, fLO = fRF - fIF Conversion Gain RF = 2350MHz 7.1 dB Input 3rd Order Intercept RF = 2350MHz 22.3 dBm SSB Noise Figure RF = 2350MHz 10.2 dB Input 1dB Compression fRF = 2350MHz, VCCIF = 3.3V fRF = 2350MHz, VCCIF = 5V 11.3 12.6 dBm dBm dc1710acf 2 DEMO MANUAL DC1710A-C PERFORMANCE SUMMARY TC = 25C, VCC = VCCIF = 3.3V, ENA = ENB = High, ISEL = Low, PLO = 0dBm, PRF = -3dBm (f = 2MHz for two-tone IIP3 tests), unless otherwise noted. (Note 1) PARAMETER CONDITIONS VALUE UNITS High Side LO Downmixer Application: ISEL = Low, RF = 1600MHz to 2300MHz, IF = 190MHz, fLO = fRF + fIF Conversion Gain RF = 1750MHz RF = 1950MHz RF = 2150MHz 9.1 8.7 8.3 dB dB dB Input 3rd Order Intercept RF = 1750MHz RF = 1950MHz RF = 2150MHz 25.3 25.4 25.1 dBm dBm dBm SSB Noise Figure RF = 1750MHz RF = 1950MHz RF = 2150MHz 9.2 9.8 10.4 dB dB dB SSB Noise Figure Under Blocking fRF = 1950MHz, fLO = 2140MHz, fBLOCK = 1850MHz, PBLOCK = 5dBm PBLOCK = 10dBm 16.5 22.7 dB dB 2LO - 2RF Output Spurious Product (fRF = fLO - fIF/2) fRF = 2045MHz at -10dBm, fLO = 2140MHz, fIF = 190MHz -68 dBc 3LO - 3RF Output Spurious Product (fRF = fLO - fIF/3) fRF = 2076.67MHz at -10dBm, fLO = 2140MHz, fIF = 190MHz -75 dBc Input 1dB Compression fRF = 1950MHz, VCCIF = 3.3V fRF = 1950MHz, VCCIF = 5V 10.6 14 dBm dBm Note 1: Subject to change without notice. Refer to the latest LTC5592 data sheet for most-up-to-date specifications. Detailed Description ABSOLUTE MAXIMUM RATINGS NOTE. Stresses beyond Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Supply Voltage (VCC)................................................4.0V IF Supply Voltage (VCCIF).........................................5.5V Enable Voltage (ENA, ENB)..............-0.3V to VCC + 0.3V Bias Adjust Voltage (IFBA, IFBB)......-0.3V to VCC + 0.3V Power Select Voltage (ISEL)............-0.3V to VCC + 0.3V LO Input Power (1GHz to 3GHz)..............................9dBm RFA, RFB Input Power (1GHz to 3GHz).................15dBm Operating Temperature Range (TC)......... -40C to 105C SUPPLY VOLTAGE RAMPING Fast ramping of the supply voltage can cause a current glitch in the internal ESD protection circuits. Depending on the supply inductance, this could result in a supply voltage transient that exceeds the maximum rating. A supply voltage ramp time of greater than 1ms is recommended. Do not clip powered test leads directly onto the demonstration circuit's VCC and VCCIF turrets. Instead, make all necessary connections with power supplies turned off, then increase to operating voltage. ENABLE FUNCTION The LTC5592's two mixer channels can be independently enabled or disabled. When the Enable voltage (ENA or ENB) is logic high (>2.5V), the corresponding mixer channel is enabled. When the Enable voltage is logic low (<0.3V), the mixer channel is disabled. The voltages at the enable pins should never fall below -0.3V or exceed the power supply voltage by more than 0.3V. The Enable pins must be pulled high or low. If left floating, the on/off state of the IC will be indeterminate. A logic table for the Enable control (ENA, ENB) is shown in Table 1. Table 1. Enable Control Logic Table ENA, ENB MIXER CHANNEL STATE Low Disabled High Enabled dc1710acf 3 DEMO MANUAL DC1710A-C detailed description LOW POWER MODE IF OUTPUTS The LTC5592 features a low power mode, which allows the flexibility to choose a 37% total power saving when lower RF performance is acceptable. When the ISEL voltage is logic low (<0.3V), both mixer channels operate at nominal power and best performance. When the ISEL voltage is logic high (>2.5V), both mixer channels are in low power mode and operate with reduced performance. The ISEL voltage should never fall below -0.3V or exceed the power supply voltage by more than 0.3V. The ISEL pin must be pulled low or high. If left floating, the operating state of the IC will be indeterminate. A logic table for ISEL is shown in Table 2. Demonstration circuit 1710A-C features single-ended, 50-matched IF outputs for 190MHz. The channel A and the channel B IF outputs are identical, and the impedance matching is realized with a bandpass topology using IF transformers as shown in Figure 1. Only channel A is shown for clarity and simplicity. Table 2. ISEL Logic Table ISEL OPERATING MODE Low Normal power, best performance High Low power, reduced performance RF INPUTS Demonstration circuit 1710A-C's RF inputs of channel A and channel B are identical. For the RF inputs to be matched, the appropriate LO signal must be applied. The RF inputs' impedance is dependent on LO frequency, but the demonstration circuit 1710A-C's RF inputs are well matched to 50 from 1.6GHz to 2.7GHz, with better than 13dB return loss, when a 1.7GHz to 2.5GHz LO signal is applied. LO INPUT The LTC5592's LO amplifier is optimized for the 1.7GHz to 2.5GHz LO frequency range. LO frequencies above and below this frequency range may be used with degraded performance. The LO input is always 50-matched when VCC is applied to the chip, even when one or both of the channels is disabled. The nominal LO input level is 0dBm. The LO input power range is between -4dBm and 6dBm. Figure 1. IF Output with Bandpass Matching Demonstration circuit 1710A-C can be easily reconfigured for other IF frequencies by simply replacing inductors L1A, L2A, L1B and L2B. Inductor values for several common IF frequencies are presented in Table 3, and return losses are plotted in Figure 2. An external load resistor, R2A, can be used to improve impedance matching if desired. Table 3. Inductor Values vs. IF Frequencies IF FREQUENCY (MHz) L1A, L2A, L1B, L2B (nH) 140 190 240 300 380 450 270 150 100 56 33 22 For IF frequencies below 90MHz, the values of the inductors become unreasonably high, and the lowpass topology shown in Figure 3 is preferred. See the LTC5592 data sheet for details. dc1710acf 4 DEMO MANUAL DC1710A-C DETAILED DESCRIPTION Demonstration circuit 1710A-C's IF outputs can be easily converted to lowpass matching. Follow the procedures below, and refer to Figure 3 and Figure 4 to modify the channel A IF output. Modifications for Channel B are similar. a. Remove existing L1A, L2A, and C7A. b. Cut the traces leading to the IF transformer close to the pads of L1A and L2A. c. Insert series inductors onto the cut traces. d. Install a 0 jumper between the pads of C5A and C7A. e. Install resistor at location R2A. Figure 3. IF Output with Lowpass Matching f. Install C9A next to, or on top of, R2A. Figure 2. IF Output Return Loss with Bandpass Matching Figure 4. IF Output with Lowpass Matching Measurement Equipment And Setup The LTC5592 is a dual high dynamic range downconverting mixer IC with very high input 3rd order intercept. Accuracy of its performance measurement is highly dependent on equipment setup and measurement technique. The recommended measurement setups are presented in Figure 5, Figure 6, and Figure 7. The following precautions should be observed: 1. Use high performance signal generators with low harmonic output and low phase noise, such as the Rohde & Schwarz SME06. Filters at the signal generators' outputs may also be used to suppress higher-order harmonics. 2. A high quality RF power combiner that provide broadband 50-termination on all ports and have good port-to-port isolation should be used, such as the MCLI PS2-17. 3. Use high performance amplifiers with high IP3 and high reverse isolation, such as the Mini-Circuits ZHL-1042J, on the outputs of the RF signal generators to improve source isolation to prevent the sources from modulating each other and generating intermodulation products. 4. Use attenuator pads with good VSWR on the demonstration circuit's input and output ports to improve dc1710acf 5 DEMO MANUAL DC1710A-C MEASUREMENT EQUIPMENT AND SETUP source and load match to reduce reflections, which may degrade measurement accuracy. b. The spectrum analyzer's internal distortion is minimized. 5. A high dynamic range spectrum analyzer, such as the Rohde & Schwarz FSEM30, should be used for linearity measurement. c. The spectrum analyzer has enough dynamic range and sensitivity. The measurement system's IIP3 should be at least 15dB better than the DUT's OIP3. 6. Use narrow resolution bandwidth (RBW) and engage video averaging on the spectrum analyzer to lower the displayed average noise level (DANL) in order to improve sensitivity and to increase dynamic range. However, the trade off is increased sweep time. d. The system is accurately calibrated for power and frequency. 7. Spectrum analyzers can produce significant internal distortion products if they are overdriven. Generally, spectrum analyzers are designed to operate at their best with about -30dBm at their input filter or preselector. Sufficient spectrum analyzer input attenuation should be used to avoid saturating the instrument, but too much attenuation reduces sensitivity and dynamic range. 8. Before taking measurements, the system performance should be evaluated to ensure that: a. Clean input signals can be produced. The two-tone signals' OIP3 should be at least 15dB better than the DUT's IIP3. A SPECIAL NOTE ABOUT RF TERMINATION The LTC5592 consists of high linearity passive doublebalanced mixer cores and IF buffer amplifiers. Due to the bidirectional nature of all passive mixers the LOIF mixing products, also referred to as pseudo-image spurs, are always present at the RF input, typically at a level 12dB below the RF input signal. Mismatched impedances at the pseudo-image spur frequencies, such as when filters are used for SSB NF measurements, can significantly impact the linearty and noise figure measurements. To avoid interference from the pseudo-image spurs, terminate the RF input port with an isolator, diplexer, or attenuator. In the recommended measurement setups presented in Figure 6 and Figure 7, the 6dB attenuator pad at the demonstration circuit's RF input serves this purpose. Quick Start Procedure Demonstration circuit 1710A-C is easy to set up to evaluate the performance of the LTC5592. Refer to Figure 5, Figure 6, and Figure 7 for proper equipment connections. The following procedures describe performing measurements on Mixer Channel A. The measurement procedures for Mixer Channel B are identical. NOTE. Care should be taken to never exceed absolute maximum input ratings. Make all connections with RF and DC power off. RETURN LOSS MEASUREMENTS 1. Configure the Network Analyzer for return loss measurement, set appropriate frequency range, and set the test signal to -3dBm. 2. Calibrate the Network Analyzer. 3. Connect all test equipment as shown in Figure 5 with the signal generator and the DC power supply turned off. 4. Increase the DC power supply voltage to 3.3V, and verify that the total current consumption is close to the figure listed in the Typical Demonstration Circuit Performance Summary. The supply voltage should be confirmed at the demo board VCC, VCCIF and GND terminals to account for lead ohmic losses. dc1710acf 6 DEMO MANUAL DC1710A-C quick start procedure 5. With the LO signal applied, and all unused demo board ports terminated in 50, measure return losses of the RFA input and IFA output ports. 6. Set the test signal to 0dBm, and re-calibrate the Network Analyzer. 7. Terminate all unused demo board ports in 50. Measure return losses of the LO input port. RF PERFORMANCE MEASUREMENTS 1. Connect all test equipment as shown in Figure 6 with the signal generators and the DC power supply turned off. 2. Increase the DC power supply voltage to 3.3V, and verify that the total current consumption is close to the figure listed in the Typical Demonstration Circuit Performance Summary. The supply voltage should be confirmed at the demo board VCC, VCCIF and GND terminals to account for lead ohmic losses. 3. Set the LO source (Signal Generator 1) to provide a 0dBm CW signal at appropriate LO frequency to the demo board LO input port. 4. Set the RF sources (Signal Generators 2 and 3) to provide two -3dBm CW signals, 2MHz apart, at the appropriate RF frequencies to the demo board RFA input port. 5. Measure the resulting IFA output on the Spectrum Analyzer: a. The wanted two-tone IF output signals are at: fIF1 = fRF1 - fLO, and fIF2 = fRF2 - fLO for low side LO, and fIF1 = fLO - fRF1, and fIF2 = fLO - fRF2 for high side LO b. The 3rd order intermodulation products which are closest to the wanted IF signals are used to calculate the Input 3rd Order Intercept: fIM3,1 = fRF1 - fLO - IF, and fIM3,2 = fRF2 - fLO + IF for low side LO, and fIM3,1 = fLO - fRF1 + IF, and fIM3,2 = fLO - fRF2 - IF for high side LO Where IF = fRF2 - fRF1. 6. Calculate Input 3rd Order Intercept: IIP3 = (IM3)/2 + PRF Where IM3 = PIF - PIM3. PIF is the lowest IF output signal power at either fIF1 or fIF2. PIM3 is the highest 3rd order intermodulation product power at either fIM3,1 or fIM3,2. PRF is the per tone RF input power. 7. Turn off one of the RF signal generators, and measure Conversion Gain, RF to IF isolation, LO to IF leakage, and Input 1dB compression point. NOISE FIGURE MEASUREMENT 1. Configure and calibrate the noise figure meter for mixer measurements. 2. Connect all test equipment as shown in Figure 7 with the signal generator and the DC power supply turned off. 3. Increase the DC power supply voltage to 3.3V, and verify that the total current consumption is close to the figure listed in the Typical Demonstration Circuit Performance Summary. The supply voltage should be confirmed at the demo board VCC, VCCIF and GND terminals to account for lead ohmic losses. 4. Measure the single-sideband noise figure. dc1710acf 7 DEMO MANUAL DC1710A-C quick start procedure Figure 5. Proper Equipment Setup for Return Loss Measurements Figure 6. Proper Equipment Setup for RF Performance Measurements dc1710acf 8 DEMO MANUAL DC1710A-C quick start procedure Figure 7. Proper Equipment Setup for Noise Figure Measurement Parts List ITEM QTY 1 6 2 1 3 REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER C1A, C1B, C3A, C3B, C5A, C5B CAP., C0G, 22pF, 1%, 50V, 0402 AVX, 04025A220FAT C2 CAP., C0G, 2.2pF, 0.1pF, 50V, 0402 AVX, 04025A2R2BAT 2 C4, C6 CAP., X5R, 1F, 10%, 10V, 0603 AVX, 0603ZD105KAT 4 2 C7A, C7B CAP., X7R, 1000pF, 5%, 50V, 0402 AVX, 04025C102JAT 5 2 C8A, C8B, CAP., C0G, 4.7pF, 0.1pF, 50V, 0402 AVX, 04025A4R7BAT 6 0 C9A, C9B (OPT) CAP., 0402, OPTION 7 7 E1, E2, E3, E4, E5, E6, E7 TESTPOINT, TURRET, 0.061" MILL-MAX, 2308-2-00-80-00-00-07-0 8 5 J1, J2, J3, J5, J6 CONN., SMA, 50, EDGE-LAUNCH AMPHENOL CONNEX, 132357 9 4 L1A, L1B, L2A, L2B IND., WIRE-WOUND, 150nH, 2%, 0603 COILCRAFT, 0603CS-R15XGLW 10 2 L3A, L3B RES., CHIP, 0, 0603 VISHAY, CRCW06030000Z0EA 11 0 R1A, R1B, R2A, R2B (OPT) RES., 0402, OPTION 12 2 T1A, T1B TRANSFORMER, SMT, RF WIDEBAND, 4:1 MINI-CIRCUITS, TC4-1W-7ALN+ 13 1 U1 IC., LTC5592IUH, QFN 5X5 LINEAR TECHNOLOGY, LTC5592IUH#PBF dc1710acf 9 D C B * * * 1 2 3 A 3 2 4 4 5 5 10 1 6 6 7 8 04-28-11 8 TECHNOLOGY 7 D C B A DEMO MANUAL DC1710A-C Schematic Diagram dc1710acf DEMO MANUAL DC1710A-C Pcb Layout Layer 1. Top Layer Layer 2. Ground Plane Layer 3. Power Plane Layer 4. Bottom Layer dc1710acf Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 DEMO MANUAL DC1710A-C DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 1630 McCarthy Blvd. Milpitas, CA 95035 Copyright (c) 2004, Linear Technology Corporation dc1710acf 12 Linear Technology Corporation LT 1011 * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2011