Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called"TAIYO YUDEN' s official sales channel"). It is only applicable to the products purchased from any of TAIYO YUDEN's official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to"Foreign Exchange and Foreign Trade Control Law"of Japan,"U.S. Export Administration Regulations", and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 12 notice_e-01 LEADED COMMON MODE CHOKE COILS FOR AC LINES WAVE FEATURES APPLICATIONS TLH10UAH TYPEThin configuration Hybrid chokeHeight 10mmMAX As a preventive measure against noise terminal voltage or power supply noise in TV's SW power supplies, NC machines, computer systems, peripheral units, measuring instruments, and controllers. TLH10UA BTYPEOrdinary configurationHybrid choke TLF10UAH TYPEThin configurationHeight 10mmMAX TLF9UA H K1 TYPESmall-sized configuration OPERATING TEMP. TLF14CB H K1 TYPEOrdinary configuration 25105Including self-generated heat TLF24HB HK1TYPELarge current capacity for power supply line use ORDERING CODE T L F 1 C B 1 4 Type TLF Common mode choke TLH Hybrid choke Core dimensionsmm 9 9 10 10 14 14 24 24 UA UAH UB CB CBH HB HBH Shape U core, vertical type U core, horizontal type core,vertically split wound Square type core vertically split wound Square type core horizontally split wound Double-square type core vertically split wound Double-square type core horizontally split wound 0 3 0 R Nominal Inductance (H) example 102 103 1000 10000 7 K 1 Rated current (A) R54 0.54 0R8 0.8 Inductance tolerance (%) Nominal Values or higher W 100/10 R=decimal point Blank space K1 Internal code Adhesive fixation Blank space Blank space EXTERNAL DIMENSIONS/MINIMUM QUANTITY TLH10UA Type 0.70.1 0.0280.004 3.50.5 0.1380.020 17.5max 0.689max 100.5 0.3940.020 0.70.1 0.0280.004 3.50.5 0.1380.020 10max 0.394max 24.5max 0.965max TLH10UB Type 18.0max 0.708max 16.0max 0.630max 18.0max 0.709max 16.0max 0.630max 17.5max 0.689max 28.0max 3.50.5 0.1380.020 TLH10UAH Type 0.70.1 0.0280.004 130.5 0.5120.020 TLF10UAH Type TLF 9UAH Type TLF14CBH Type TLF24HB Type 3.50.5 0.1380.020 10max 0.394max 100.5 0.3940.020 0.70.1 0.0280.004 TLF 9UA Type 28.0max 24.5max 0.965max 130.5 0.5120.020 0.8 0.031 19.0max 0.748max 26.0max 1.024max 13.00.5 0.5120.020 41 100.5 0.1570.039 0.3940.020 30max 1.181max TLF14CB Type Unit : mm (inch) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 162 12 coil04_e-02 25max 0.984max 0.8 0.031 21max 41 150.5 0.827max 0.5910.020 0.1570.039 TLF24 HBH Type 25max 0.984max Type Minimum Quantity (pcs.) Box TLH Type TLF Type 500 210.5 0.8270.020 Unit : mm (inch) PART NUMBERS TLH10UAH Type Hybrid choke TLH10UAH872 0R7 TLH10UAH992 0R6 TLH10UAH123 0R5 EHS RoHS RoHS RoHS Common Mode Inductance [mH] 8.7 9.9 12.0 Inductance Tolerance min. Normal Mode Inductance [mH] Typ. 0.70 0.85 1.06 DC Resistance [] (max.) 1.00 1.35 1.60 Normal Mode Inductance [mH] Typ. 0.067 0.087 0.126 0.160 0.215 0.330 0.430 0.644 0.836 1.256 DC Resistance [] (max.) 0.089 0.126 0.171 0.222 0.272 0.398 0.578 0.878 1.138 1.567 Normal Mode Inductance [mH] Typ. 0.056 0.068 0.113 0.150 0.232 0.328 0.580 0.735 0.877 DC Resistance [] (max.) 0.097 0.133 0.214 0.274 0.422 0.624 0.982 1.314 1.577 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 0.7 0.6 0.5 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.7 0.6 0.5 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 2.0 1.7 1.4 1.2 1.0 0.8 0.7 0.6 0.5 AC250 0.110 TLH10UA Type Hybrid choke Ordering code TLH10UA 901 2R0 TLH10UA 112 1R8 TLH10UA 152 1R6 TLH10UA 212 1R4 TLH10UA 282 1R2 TLH10UA 432 1R0 TLH10UA 622 0R8 TLH10UA 872 0R7 TLH10UA 992 0R6 TLH10UA 143 0R5 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 0.9 1.1 1.5 2.1 2.8 4.3 6.2 8.7 9.9 14.0 Inductance Tolerance min. TLH10UB Type Hybrid choke Ordering code TLH10UB 701 2R0 TLH10UB 112 1R7 TLH10UB 142 1R4 TLH10UB 232 1R2 TLH10UB 352 1R0 TLH10UB 442 0R8 TLH10UB 872 0R7 TLH10UB 972 0R6 TLH10UB 113 0R5 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 0.7 1.1 1.4 2.3 3.5 4.4 8.7 9.7 11.0 Inductance Tolerance min. TLF10UAH Type Ordering code TLF10UAH872 0R7 TLF10UAH992 0R6 TLF10UAH123 0R5 EHS RoHS RoHS RoHS Common Mode Inductance [mH] 8.7 9.9 12.0 Inductance Tolerance min. DC Resistance [] (max.) 1.00 1.35 1.60 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 0.7 0.6 0.5 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 0.80 0.54 0.42 0.32 0.25 0.23 AC250 0.110 COMMON MODE FILTERS NOISE SUPPRESSION COMPONENTS Ordering code TLF 9UA Type Ordering code TLF 9UA 102W0R8K1 TLF 9UA 202WR54K1 TLF 9UA 302WR42K1 TLF 9UA 502WR32K1 TLF 9UA 802WR25K1 TLF 9UA 103WR23K1 EHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.0 2.0 3.0 5.0 8.0 10.0 Inductance Tolerance 100/10 DC Resistance [] (max.) 0.5 1.0 1.5 2.5 4.0 4.5 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. coil04_e-02 12 163 PART NUMBERS TLF 9UAH Type Ordering code EHS TLF 9UAH102W0R8K1 TLF 9UAH202WR54K1 TLF 9UAH302WR42K1 TLF 9UAH502WR32K1 TLF 9UAH802WR25K1 TLF 9UAH103WR23K1 RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.0 2.0 3.0 5.0 8.0 10.0 Inductance Tolerance 100/10 DC Resistance [] (max.) 0.5 1.0 1.5 2.5 4.0 4.5 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 0.80 0.54 0.42 0.32 0.25 0.23 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 1.5 1.2 1.0 1.0 0.8 0.8 0.7 0.4 0.3 0.2 0.2 0.2 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 1.5 1.2 1.0 1.0 0.8 0.8 0.7 0.4 0.3 0.2 0.2 0.2 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 3.0 2.2 2.0 1.8 1.5 1.4 1.2 1.0 1.0 0.9 0.8 0.6 0.5 AC250 0.110 Rated current [A] (max.) Rated voltage [V]max. Applicable frequency [MHz] Reference 3.0 2.2 2.0 1.8 1.5 1.4 1.2 1.0 1.0 0.9 0.8 0.6 0.5 AC250 0.110 TLF14CB Type Ordering code TLF14CB 102 1R5K1 TLF14CB 222 1R2K1 TLF14CB 332 1R0K1 TLF14CB 472 1R0K1 TLF14CB 562 0R8K1 TLF14CB 682 0R8K1 TLF14CB 103 0R7K1 TLF14CB 223 0R4K1 TLF14CB 333 0R3K1 TLF14CB 473 0R2K1 TLF14CB 563 0R2K1 TLF14CB 683 0R2K1 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.0 2.2 3.3 4.7 5.6 6.8 10.0 22.0 33.0 47.0 56.0 68.0 Inductance Tolerance min. DC Resistance [] (max.) 0.10 0.18 0.32 0.38 0.42 0.60 0.85 1.7 2.7 3.6 5.0 6.5 TLF14CBH Type Ordering code TLF14CBH102 1R5K1 TLF14CBH222 1R2K1 TLF14CBH332 1R0K1 TLF14CBH472 1R0K1 TLF14CBH562 0R8K1 TLF14CBH682 0R8K1 TLF14CBH103 0R7K1 TLF14CBH223 0R4K1 TLF14CBH333 0R3K1 TLF14CBH473 0R2K1 TLF14CBH563 0R2K1 TLF14CBH683 0R2K1 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.0 2.2 3.3 4.7 5.6 6.8 10.0 22.0 33.0 47.0 56.0 68.0 Inductance Tolerance min. DC Resistance [] (max.) 0.10 0.18 0.32 0.38 0.42 0.60 0.85 1.7 2.7 3.6 5.0 6.5 TLF24HB Type Ordering code TLF24HB 122 3R0K1 TLF24HB 222 2R2K1 TLF24HB 272 2R0K1 TLF24HB 332 1R8K1 TLF24HB 392 1R5K1 TLF24HB 562 1R4K1 TLF24HB 682 1R2K1 TLF24HB 822 1R0K1 TLF24HB 103 1R0K1 TLF24HB 123 0R9K1 TLF24HB 183 0R8K1 TLF24HB 273 0R6K1 TLF24HB 333 0R5K1 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.2 2.2 2.7 3.3 3.9 5.6 6.8 8.2 10.0 12.0 18.0 27.0 33.0 Inductance Tolerance min. DC Resistance [] (max.) 0.045 0.080 0.090 0.120 0.130 0.187 0.254 0.275 0.345 0.350 0.550 0.880 1.150 TLF24HBH Type Ordering code TLF24HBH122 3R0K1 TLF24HBH222 2R2K1 TLF24HBH272 2R0K1 TLF24HBH332 1R8K1 TLF24HBH392 1R5K1 TLF24HBH562 1R4K1 TLF24HBH682 1R2K1 TLF24HBH822 1R0K1 TLF24HBH103 1R0K1 TLF24HBH123 0R9K1 TLF24HBH183 0R8K1 TLF24HBH273 0R6K1 TLF24HBH333 0R5K1 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Common Mode Inductance [mH] 1.2 2.2 2.7 3.3 3.9 5.6 6.8 8.2 10.0 12.0 18.0 27.0 33.0 Inductance Tolerance min. DC Resistance [] (max.) 0.045 0.080 0.090 0.120 0.130 0.187 0.254 0.275 0.345 0.350 0.550 0.880 1.150 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 164 12 coil04_e-02 ELECTRICAL CHARACTERISTICS Impedance-Frequency characteristic TLH10UAH TypeCommon Mode Impedance TLH10UAH TypeNormal Mode Impedance 1000 TLH10UA TypeCommon Mode Impedance 1000 TLH10UA TypeNormal Mode Impedance 143 0R5 123 0R5 100 100 872 0R7 123 0R5 992 0R6 143 0R5 432 1R0 992 0R6 10 10 872 0R7 282 1R2 432 1R0 872 0R7 1 872 0R7 282 1R2 1 152 1R6 152 1R6 901 2R0 0.1 0.01 1000 TLH10UB TypeCommon Mode Impedance 1000 0.1 1 TLF10UAH Type TLH10UB TypeNormal Mode Impedance 10 100 0.1 0.01 901 2R0 0.1 1 10 100 TLF9UA/TLF9UAH Type 113 0R5 100 123 0R5 100 872 0R7 113 0R5 442 0R8 10 992 0R6 10 442 0R8 142 1R4 1 872 0R7 1 142 1R4 701 2R0 0.1 0.01 0.1 701 2R0 1 10 100 0.1 0.01 0.1 TLF14CB/TLF14CBH Type 1 10 100 TLF24HB/TLF24HBH Type 123 0R9 472 1R5 392 1R76 Test conditions Equipment : HP-4294A Test circuit : To impedance analyzer COMMON MODE FILTERS NOISE SUPPRESSION COMPONENTS 872 0R7 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. coil04_e-02 12 165 PACKAGING Minimum Quantity CM/BU Type Type CM05RA06 CM05RB CM08RA CM08RB CM12RA02 BU08RA Minimum Quantity (pcs.) Box Bulk -- 500 1000 -- -- 250 500 -- -- 100 -- 200 TL Type Type TLH10UA TLH10UB TLF10UAH TLF9UA TLF9UB TLF14CB TLF24HB Minimum Quantity (pcs.) Box 500 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. coil0304_pack_e-01 12 coil0304_pack-P1 RELIABILITY DATA 1. Operating Temperature Range CM-RA/BU-RA Type CM-RB Type 25105 TLH, TLF Type Test method and remarks Including temperature rise due to self-generated heat. 2. Storage temperature range CM-RA/BU-RA Type CM-RB Type TLH, TLF Type 4085 3. Rated current CM-RA/BU-RA Type CM-RB Type Within the specified range TLH, TLF Type Test method and remarks CM:The maximum value of DC current within a specified rise of temperature individually. TLH10U, TLF10UAH: The maximum value of AC current within the temperature rise of 60 TLF9UA, 14CB: The maximum value of AC current within the temperature rise of 45 TLF9UB: The maximum value of DC current within the temperature rise of 45 4. Inductance CM-RA/BU-RA Type CM-RB Type Within the specified tolerance TLH, TLF Type Test method and remarks CM : Measuring equipment : 4263A (HP) or its equivalent Measuring frequency : 1kHz TLF9U : Measuring equipment : Impedance analyzer (HP4192A) or its equivalent Measuring frequency : 1kHz Measuring voltage : 0.35Vosc TLH, TLF (except TLF9U) : Measuring equipment : LCR meter 4284A or its equivalent Measuring frequency : 1kHz Measuring voltage : 1.0V 5. DC resistance CM-RA/BU-RA Type CM-RB Type Within the specified tolerance TLH, TLF Type Test method and remarks CM, TLH, TLF : Measuring equipment : DC ohmmeter 6. Terminal strength tensile force CM-RA/BU-RA Type CM-RB Type No abnormality TLH, TLF Type Test method and remarks CM : Fix the component in the direction to draw terminal and gradually apply tensile force as detailed in indiviual specifications. TLF9U : Apply the stated tensile force gradually in the direction to draw terminal. Nominal wire diameter tensile d [mm] 0.6 force [N] duration [s] 5 305 TLH, TLF (except TLF9U): Apply the stated tensile force gradually in the direction to draw terminal. Nominal wire diameter tensile d [mm] 0.8 force [N] duration [s] 10 305 7. Insulation resistance between wires CM-RA/BU-RA Type CM-RB Type 100M min. TLH, TLF Type Test method and remarks CM, TLH, TLF : Applied voltage : Rated voltage (CM-RA/BU-RA, CM-RB : 500VDC (TLH, TLF (except TLF9UB)) : 250VDC (TLF9UB) Duration : 60sec. 8. Insulation resistance between wire and core CM-RA/BU-RA Type CM-RB Type except TLH, TLF10UAH Type 100M min. TLH, TLF Type Test method and remarks : Applied voltage : 500VDC (TLF (except TLF9UB)) TLF : 250VDC (TLF9UB) Duration : 60 sec. 9. Withstanding : between wires CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Test method and remarks CM, TLH, TLF : Applied voltage : : : Duration : No abnormality 250VDC (CM-RA/BU-RA, CM-RB 2000VAC (TLH, TLF (except TLF9UB) 500VDC (TLF9UB) 60sec. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. co0304_reli-RP1 12 co0304_reli_e-01 RELIABILITY DATA 10. Withstanding : between wires and core CM-RA/BU-RA Type CM-RB Type except TLH, TLF10UAH Type No abnormality TLH, TLF Type Test method and remarks : Applied voltage : 2000VAC (TLF (except TLF9UB)) TLF : 500VDC (TLF9UB) Duration : 60sec. 11. Rated voltage CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Test method and remarks TLH, TLF (except TLF9UB) : 250VAC TLF9UB : 50VDC Within the specified range 12. Resistance to vibration CM-RA/BU-RA Type Inductance change : Within 15% CM-RB Type Appearance : No abnormality TLH, TLF (except TLF9U) : Within the specified range TLH, TLF Type TLF9U : Inductance change : Within 5 Test method and remarks CM, TLH, TLF : According to JIS C 0040 Direction : 2hrs each in X, Y and Z direction Total : 6hrs Frequency range : 10 to 55 to 10Hz (1 min.) Amplitude : 1.5mm (shall not exceed acceleration 196m/s2) Mounting method : soldering onto PC board Recovery : 2 to 24 hrs of recovery under the standard condition after the test. (CM-RB) : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. (TLH, TLF) 13. Solderability CM-RA/BU-RA Type At least 75% of terminal electrode is covered by new solder. CM-RB Type TLH, TLF Type Solder shall be uniformly adhered onto immersed surfaces. Test method and remarks : Solder temperature : 2355 CM Duration : 20.5sec. Immersion depth : According to detailed specification. TLH, TLF : Solder temperature : 2455 Duration : 41sec. Immersion depth : Up to 1.0 to 1.5mm from PBC mounted level. 14. Resistance to soldering heat CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Test method and remarks : Solder temperature : CM Duration : Immersion depth : Recovery : TLH, TLF : Solder temperature : Duration : Immersion depth : Recovery : 15. Thermnal shock CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Appearance : No abnormality Inductance change : Refer to individual specification TLF9UA : Inductance change : Within 5% TLF14CB : Within the specified range 2605 50.5sec. Up to 22.5mm from terminal root. 1 to 2 hrs of recovery under the standard condition after the test. 2605 101sec. Up to 1.0 to 1.5mm from PBC mounted level. At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. Appearance : No abnormality Inductance change : Refer to individual specification : Inductance change : Within 15% TLF9UA TLH, TLF (except TLF9UA) : Withstanding voltage : No abnormality Insulation resistance : No abnormality Test method and remarks CM, TLH, TLF : According to JIS C 0025 Conditions for 1 cycle Step Temperature Durrationmin 1 253 303 2 Room Temperature Within 3 3 852 303 4 Room Temperature Within 3 Number of cycles : 10 Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2 hrs. 16. Damp heat CM-RA/BU-RA Type CM-RB Type TLH, TLF Type : Within 15% : Inductance change TLF9UA TLH, TLF (except TLF9UA) : Withstanding voltage : No abnormality Insulation resistance : No abnormality Test method and remarks TLH, TLF : Temperature : 602 402 (TLF14CB) Humidity : 9095RH Duration : 500 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. co0304_reli_e-01 12 co0304_reli-RP2 RELIABILITY DATA 17. Loading under damp heat CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Test method and remarks : Temperature : CM Humidity : Duration : Applied current : Recovery : Appearance : No abnormality Inductance change : Refer to individual specification Withstanding voltage : No abnormality Insulation resistance : No abnormality 402 9095%RH 500 (12, 0) hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from test chamber. TLH, TLF : Temperature : 602 402 (TLF14CB) Humidity : 9095%RH Duration : 100 hrs 500 hrs Apply rated current across windings (TLF14CB) Applied voltage : Apply the following specified voltage between windings. Recovery TLF9UA 250VAC TLF9UB 50VDC : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. 18. Low temperature life test CM-RA/BU-RA Type CM-RB Type Appearance : No abnormality Inductance change : Refer to individual specification : Inductance change : Within 15% TLF9U TLH, TLF (except TLF9U) : Withstanding voltage : No abnormality TLH, TLF Type Insulation resistance : No abnormality Test method and remarks : Temperature : 403 CM Duration : 500 (12, 0) hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from test chamber. TLH, TLF : Temperature : : Duration : Recovery : 252 402 (TLF14CB) 500 hrs At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. 19. High Temperature life test CM-RA/BU-RA Type CM-RB Type TLH, TLF Type Appearance : No abnormality Inductance change : Refer to individual specification : Within 15% : Inductance change TLF9U TLH, TLF (except TLF9U) : Withstanding voltage : No abnormality Insulation resistance : No abnormality Test method and remarks : Temperature : 852 CM Duration : 500 (12, 0) hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from test chamber. TLH, TLF : Temperature : : Duration : Recovery : 852 1053 (TLF14CB) 500 hrs At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. co0304_reli-RP3 12 co0304_reli_e-01 PRECAUTIONS CM-RA Type, CM-RB Type, TLH, TLF Type 1. Circuit Design Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. Technical Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of considerations the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. Precautions 3. Soldering Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, etc. sufficiently. Precautions Recommended conditions for using a soldering iron Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration - 3 seconds or less The soldering iron should not directly touch the product. Technical Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of considerations the products. 4. Cleaning Precautions Cleaning conditions 1. TLF type Please contact any of our offices for about a cleaning. 5. Handling Handling 1. Keep the product away from all magnets and magnetic objects. Mechanical considerations 1. Please do not give the product any excessive mechanical shocks. 2. TLF type Precautions Please do not add any shock or power to a product in transportation. Packing 1. Please do not give the product any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). Handling 1. There is a case that a characteristic varies with magnetic influence. Mechanical considerations Technical 1. There is a case to be damaged by a mechanical shock. consider2. TLF type ations There is a case to be broken by a fall. Packing 1. There is a case that a lead route turns at by a fall or an excessive shock. 6. Storage conditions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Precautions Recommended conditions Ambient temperature : 040 Humidity : Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, the solderbility of electrodes decreases gradually, so the products should be mounted within one year from the time of delivery. Technical considerations In case of storage over 6 months, solderability shall be checked before actual usage. Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. co0304_reli-RP4 12 co0304_reli_e-01