IDT5V991A-2JGI - Integrated Device Technology, Inc.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

SEPTEMBER 2001

2001 Integrated Device Technology, Inc. DSC 5963/3c

IDT5V991A

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

3.3V PROGRAMMABLE

SKEW PLL CLOCK DRIVER

TURBOCLOCK™

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

FEATURES:

• REF is 5V tolerant

• 4 pairs of programmable skew outputs

• Low skew: 200ps same pair, 250ps all outputs

• Selectable positive or negative edge synchronization:

Excellent for DSP applications

• Synchronous output enable

• Output frequency: 3.75MHz to 85MHz

• 2x, 4x, 1/2, and 1/4 outputs

• 3 skew grades:

IDT5V991A-2: tSKEW0<250ps

IDT5V991A-5: tSKEW0<500ps

IDT5V991A-7: tSKEW0<750ps

• 3-level inputs for skew and PLL range control

• PLL bypass for DC testing

• External feedback, internal loop filter

• 12mA balanced drive outputs

• Low Jitter: <200ps peak-to-peak

• Available in 32-pin PLCC Package

DESCRIPTION:

The IDT5V991A is a high fanout 3.3V PLL based clock driver intended

for high performance computing and data-communications applications. A

key feature of the programmable skew is the ability of outputs to lead or lag

the REF input signal. The IDT5V991A has eight programmable skew

outputs in four banks of 2. Skew is controlled by 3-level input signals that

may be hard-wired to appropriate HIGH-MID-LOW levels.

When the GND/sOE pin is held low, all the outputs are synchronously

enabled. However, if GND/sOE is held high, all the outputs except 3Q0 and

3Q1 are synchronously disabled.

Furthermore, when the VCCQ/PE is held high, all the outputs are

synchronized with the positive edge of the REF clock input. When VCCQ/

PE is held low, all the outputs are synchronized with the negative edge of

REF. Both devices have LVTTL outputs with 12mA balanced drive outputs.

FUNCTIONAL BLOCK DIAGRAM

GND/sOE

1Q0

Skew

Select

1Q1

1F1:0

2Q0

Skew

Select

2Q1

2F1:0

REF

PLL

3Q0

Skew

Select

3Q1

3F1:0

4Q0

4Q1

Skew

Select

4F1:0

VCCQ/PE

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

PIN CONFIGURATION

NOTE:

1. Stresses beyond those listed under ABSOLUTE MAXIMUM RATINGS may cause

permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions above those indicated in the

operational sections of this specification is not implied. Exposure to absolute-

maximum-rated conditions for extended periods may affect device reliability.

3F1

4F0

4F1

VCCQ/PE

4Q1

4Q0

GND

2F0

GND/sOE

1F1

1F0

1Q0

1Q1

GND

4 3 2 1 32 31 30

14 15 16 17 18 19 20

REF

GND

TEST

VCCN

CCN

CCQ

VCCN

PLCC

TOP VIEW

Output skew with respect to the REF input is adjustable to compensate

for PCB trace delays, backplane propagation delays or to accommodate

requirements for special timing relationships between clocked compo-

nents. Skew is selectable as a multiple of a time unit tU which is of the

order of a nanosecond (see PLL Programmable Skew Range and Resolution

Table). There are nine skew configurations available for each output

pair. These configurations are chosen by the nF1:0 control pins. In order

to minimize the number of control pins, 3-level inputs (HIGH-MID-LOW)

are used, they are intended for but not restricted to hard-wiring. Undriven

3-level inputs default to the MID level. Where programmable skew is

not a requirement, the control pins can be left open for the zero skew

default setting. The Control Summary Table shows how to select specific

skew taps by using the nF1:0 control pins.

PROGRAMMABLE SKEW

ABSOLUTE MAXIMUM RATINGS(1)

Symbol Description Max Unit

Supply Voltage to Ground –0.5 to +7 V

VIDC Input Voltage –0.5 to VCC+0.5 V

REF Input Voltage –0.5 to +5.5 V

TJJunction Temperature 1 5 0 °C

TSTG Storage Temperature –65 to +150 °C

NOTE:

1. Capacitance applies to all inputs except TEST, FS, and nF1:0.

CAPACITANCE(TA = +25°C, f = 1MHz, VIN = 0V)

Parameter Description Typ. Max. Unit

CIN Input Capacitance 5 7 pF

PIN DESCRIPTION

Pin Name Type Description

REF IN Reference Clock Input

FB IN Feedback Input

TEST (1) IN When MID or HIGH, disables PLL (except for conditions of Note 1). REF goes to all outputs. Skew selections (see Control

Summary Table) remain in effect. Set LOW for normal operation.

GND/ sOE (1) IN Synchronous Output Enable. When HIGH, it stops clock outputs (except 3Q0 and 3Q1) in a LOW state - 3Q0 and 3Q1 may be used

as the feedback signal to maintain phase lock. When TEST is held at MID level and GND/sOE is HIGH, the nF[1:0] pins act as

output disable controls for individual banks when nF[1:0] = LL. Set GND/sOE LOW for normal operation.

VCCQ/PE IN Selectable positive or negative edge control. When LOW/HIGH the outputs are synchronized with the negative/positive edge of the

reference clock.

nF[1:0] IN 3-level inputs for selecting 1 of 9 skew taps or frequency functions

FS IN Selects appropriate oscillator circuit based on anticipated frequency range. (See PLL Programmable Skew Range.)

nQ[1:0] OUT Four banks of two outputs with programmable skew

VCCN PWR Power supply for output buffers

VCCQ PWR Power supply for phase locked loop and other internal circuitry

GND PWR Ground

NOTE:

1.When TEST = MID and GND/sOE = HIGH, PLL remains active with nF[1:0] = LL functioning as an output disable control for individual output banks. Skew selections remain

in effect unless nF[1:0] = LL.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

EXTERNAL FEEDBACK

By providing external feedback, the IDT5V991A gives users flexibility

with regard to skew adjustment. The FB signal is compared with the

input REF signal at the phase detector in order to drive the VCO. Phase

differences cause the VCO of the PLL to adjust upwards or downwards

accordingly.

NOTES:

1. The device may be operated outside recommended frequency ranges without damage, but functional operation is not guaranteed. Selecting the appropriate FS value based on

input frequency range allows the PLL to operate in its ‘sweet spot’ where jitter is lowest.

2. The level to be set on FS is determined by the nominal operating frequency of the VCO and Time Unit Generator. The VCO frequency always appears at 1Q 1:0, 2Q1:0, and the

higher outputs when they are operated in their undivided modes. The frequency appearing at the REF and FB inputs will be the same as the VCO when the output connected

to FB is undivided. The frequency of the REF and FB inputs will be 1/2 or 1/4 the VCO frequency when the part is configured for a frequency multiplication by using a divided

output as the FB input.

3. Skew adjustment range assumes that a zero skew output is used for feedback. If a skewed Q output is used for feedback, then adjustment range will be greater. For example

if a 4tU skewed output is used for feedback, all other outputs will be skewed –4tU in addition to whatever skew value is programmed for those outputs. ‘Max adjustment’ range

applies to output pairs 3 and 4 where ± 6tU skew adjustment is possible and at the lowest FNOM value.

An internal loop filter moderates the response of the VCO to the

phase detector. The loop filter transfer function has been chosen to

provide minimal jitter (or frequency variation) while still providing accu-

rate responses to input frequency changes.

FS = LOW FS = MID FS = HIGH Comments

Timing Unit Calculation (tU) 1/(44 x FNOM) 1/(26 x FNOM) 1/(16 x FNOM)

VCO Frequency Range (FNOM)(1,2) 15 to 35MHz 25 to 60MHz 40 to 85 MHz

Skew Adjustment Range(3)

Max Adjustment: ±9.09ns ±9.23ns ±9.38ns ns

±49º ±83º ±135º Phase Degrees

±14% ±23% ±37% % of Cycle Time

Example 1, FNOM = 15MHz tU = 1.52ns — —

Example 2, FNOM = 25MHz tU = 0.91ns tU = 1.54ns —

Example 3, FNOM = 30MHz tU = 0.76ns tU = 1.28ns —

Example 4, FNOM = 40MHz — tU = 0.96ns tU = 1.56ns

Example 5, FNOM = 50MHz — tU = 0.77ns tU = 1.25ns

Example 6, FNOM = 80MHz — — tU = 0.78ns

PLL PROGRAMMABLE SKEW RANGE AND RESOLUTION TABLE

CONTROL SUMMARY TABLE FOR FEEDBACK SIGNALS

nF 1 : 0 Skew (Pair #1, #2) Skew (Pair #3) Skew (Pair #4)

LL(1) –4tUDivide by 2 Divide by 2

LM –3tU–6tU–6tU

LH –2tU–4tU–4tU

ML –1tU–2tU–2tU

MM Zero Skew Zero Skew Zero Skew

MH 1tU2tU2tU

HL 2tU4tU4tU

HM 3tU6tU6tU

HH 4tUDivide by 4 Inverted(2)

NOTES:

1. LL disables outputs if TEST = MID and GND/sOE = HIGH.

2. When pair #4 is set to HH (inverted), GND/sOE disables pair #4 HIGH when VCCQ/PE = HIGH, GND/sOE disables pair #4 LOW when VCCQ/PE = LOW.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE

Symbol Parameter Conditions Min. Max. Unit

VIH Input HIGH Voltage Guaranteed Logic HIGH (REF, FB Inputs Only) 2 — V

VIL Input LOW Voltage Guaranteed Logic LOW (REF, FB Inputs Only) — 0.8 V

VIHH Input HIGH Voltage(1) 3-Level Inputs Only VCC−0.6 — V

VIMM Input MID Voltage(1) 3-Level Inputs Only VCC/2−0.3 VCC/2+0.3 V

VILL Input LOW Voltage(1) 3-Level Inputs Only — 0.6 V

IIN Input Leakage Current VIN = VCC or GND — ±5 µA

(REF, FB Inputs Only) VCC = Max.

VIN = VCC HIGH Level — ±200

I33-Level Input DC Current (TEST, FS, nF1:0)VIN = VCC/2 MID Level — ± 50 µA

VIN = GND LOW Level — ±200

IPU Input Pull-Up Current (VCCQ/PE) VCC = Max., VIN = GND — ±100 µA

IPD Input Pull-Down Current (GND/sOE)VCC = Max., VIN = VCC — ±100 µA

VOH Output HIGH Voltage VCC = Min., IOH = −12mA 2.4 — V

VOL Output LOW Voltage VCC = Min., IOL = 12mA — 0.55 V

NOTE:

1. These inputs are normally wired to VCC, GND, or unconnected. Internal termination resistors bias unconnected inputs to VCC/2. If these inputs are switched, the function and

timing of the outputs may be glitched, and the PLL may require an additional tLOCK time before all datasheet limits are achieved.

RECOMMENDED OPERATING RANGE IDT5V991A-2, -5, -7 IDT5V991A-2

(Industrial) (Commercial)

Symbol Description Min. Max. Min. Max. Unit

Vcc Power Supply Voltage 3 3.6 3 3.6 V

TAAmbient Operating Temperature -40 +85 0 +70 °C

POWER SUPPLY CHARACTERISTICS

Symbol Parameter Test Conditions(1) Typ.(2) Max. Unit

ICCQ Quiescent Power Supply Current VCC = Max., TEST = MID, REF = LOW, 8 25 mA

VCCQ/PE = LOW, GND/sOE = LOW

All outputs unloaded

ΔICC Power Supply Current per Input HIGH VCC = Max., VIN = 3V 1 30 μA

ICCD Dynamic Power Supply Current per Output VCC = Max., CL = 0pF 55 90 μA/MHz

ITOT Total Power Supply Current VCC = 3.3V, FREF = 20MHz, CL = 160pF(1) 29 —

VCC = 3.3V, FREF = 33MHz, CL = 160pF(1) 42 — mA

VCC = 3.3V, FREF = 66MHz, CL = 160pF(1) 76 —

NOTE:

1. For eight outputs, each loaded with 20pF.

INPUT TIMING REQUIREMENTS

Symbol Description (1) Min. Max. Unit

tR, tFMaximum input rise and fall times, 0.8V to 2V — 10 ns/V

tPWC Input clock pulse, HIGH or LOW 3 — n s

DHInput duty cycle 1 0 9 0 %

REF Reference Clock Input 3.75 85 MHz

NOTE:

1. Where pulse width implied by DH is less than tPWC limit, tPWC limit applies.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

SWITCHING CHARACTERISTICS OVER OPERATING RANGE

IDT5V991A-2 IDT5V991A-5 IDT5V991A-7

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit

FNOM VCO Frequency Range See PLL Programmable Skew Range and Resolution Table

tRPWH REF Pulse Width HIGH(11) 3—— 3——3——ns

tRPWL REF Pulse Width LOW(11) 3—— 3——3——ns

tUProgrammable Skew Time Unit See Control Summary Table

tSKEWPR Zero Output Matched-Pair Skew (xQ0, xQ1)(1,2,3) — 0.05 0.2 — 0.1 0.25 — 0.1 0.25 ns

tSKEW0 Zero Output Skew (All Outputs)(1,4,5) — 0.1 0.25 — 0.25 0.5 — 0.3 0.75 ns

tSKEW1 Output Skew — 0.25 0.5 — 0.6 0.7 — 0.6 1 ns

(Rise-Rise, Fall-Fall, Same Class Outputs)(1,6)

tSKEW2 Output Skew — 0.3 1.2 — 0.5 1.2 — 1 1.5 ns

(Rise-Fall, Nominal-Inverted, Divided-Divided)(1,6)

tSKEW3 Output Skew — 0.25 0.5 — 0.5 0.7 — 0.7 1.2 ns

(Rise-Rise, Fall-Fall, Different Class Outputs)(1,6)

tSKEW4 Output Skew — 0.5 0.9 — 0.5 1 — 1.2 1.7 ns

(Rise-Fall, Nominal-Divided, Divided-Inverted)(1,2)

tDEV Device-to-Device Skew(1,2,7) — — 0.75 — — 1.25 — — 1.65 ns

tPD REF Input to FB Propagation Delay(1,9) −0.25 0 0.25 −0.5 0 0.5 −0.7 0 0.7 ns

tODCV Output Duty Cycle Variation from 50%(1) −1.2 0 1.2 −1.2 0 1.2 −1.2 0 1.2 ns

tPWH Output HIGH Time Deviation from 50%(1,10) — — 2 — — 2.5 — — 3 ns

tPWL Output LOW Time Deviation from 50%(1,11) — — 1.5 — — 3 — — 3.5 ns

tORISE Output Rise Time(1) 0.15 1 1.2 0.15 1 1.5 0.15 1.5 2.5 ns

tOFALL Output Fall Time(1) 0.15 1 1.2 0.15 1 1.5 0.15 1.5 2.5 ns

tLOCK PLL Lock Time(1,8) — — 0.5 — — 0.5 — — 0.5 ms

tJR Cycle-to-Cycle Output Jitter(1) RMS — — 25 — — 25 — — 25 ps

Peak-to-Peak — — 200 — — 200 — — 200

NOTES:

1. All timing and jitter tolerances apply for FNOM > 25MHz.

2. Skew is the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with the specified

load.

3. tSKEWPR is the skew between a pair of outputs (xQ0 and xQ1) when all eight outputs are selected for 0tU.

4. tSKEW0 is the skew between outputs when they are selected for 0tU.

5. For IDT5V991A-2 tSKEW0 is measured with CL = 0pF; for CL = 30pF, tSKEW0 = 0.35ns Max.

6. There are 3 classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2 or Divide-

by-4 mode).

7. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC, ambient temperature, air flow, etc.)

8. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is

measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits.

9. tPD is measured with REF input rise and fall times (from 0.8V to 2V) of 1ns.

10. Measured at 2V.

11. Measured at 0.8V.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

AC TEST LOADS AND WAVEFORMS

2.0V

tPWL

tPWH

tORISE tOFALL

0.8V

≤1ns ≤1ns

2.0V

0.8V

3.0V

Vth = 1.5V

150Ω

VCC

Output

150Ω20pF

LVTTL Input Test Waveform

LVTTL Output Waveform

Test Load

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

REF

OTHER Q

INVERTED Q

REF DIVIDED BY 2

REF DIVIDED BY 4

tJR

tREF

tPD

tSKEW2

tSKEW3, 4

tSKEW1, 3, 4 tSKEW2, 4

tSKEW3, 4

tSKEW2

tSKEWPR

tSKEW0, 1

tODCV tODCV

tRPWH

tRPWL

tSKEWPR

tSKEW0, 1

AC TIMING DIAGRAM

NOTES:

VCCQ/PE: The AC Timing Diagram applies to VCCQ/PE=VCC. For VCCQ/PE=GND, the negative edge of FB aligns with the negative edge of REF, divided outputs change on the

negative edge of REF, and the positive edges of the divide-by-2 and the divide-by-4 signals align.

Skew: The time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are loaded with 20pF and terminated

with 75Ω to VCC/2.

tSKEWPR: The skew between a pair of outputs (xQ0 and xQ1) when all eight outputs are selected for 0tU.

tSKEW0: The skew between outputs when they are selected for 0tU.

tDEV: The output-to-output skew between any two devices operating under the same conditions (VCC, ambient temperature, air flow, etc.)

tODCV: The deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications.

tPWH is measured at 2V.

tPWL is measured at 0.8V.

tORISE and tOFALL are measured between 0.8V and 2V.

tLOCK: The time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is measured

from the application of a new signal or frequency at REF or FB until tPD is within specified limits.

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

IDT5V991A

3.3V PROGRAMMABLE SKEW PLL CLOCK DRIVER TURBOCLOCK

ORDERING INFORMATION

IDT XXXXX XX X

Package Process

Device Type

Blank

5V991A-2

5V991A-5

5V991A-7

3.3V Programmable Skew PLL Clock Driver TurboClock

Rectangular Plastic Leaded Chip Carrier

PLCC - Green

Commercial (0°C to +70°C)

Industrial (-40°C to +85°C)

CORPORATE HEADQUARTERS for SALES: for Tech Support:

6024 Silver Creek Valley Road 800-345-7015 or 408-284-8200 clockhelp@idt.com

San Jose, CA 95138 fax: 408-284-2775