LTC2285 Dual 14-Bit, 125Msps Low Power 3V ADC DESCRIPTION FEATURES n n n n n n n n n n n n n Integrated Dual 14-Bit ADCs Sample Rate: 125Msps Single 3V Supply (2.85V to 3.4V) Low Power: 790mW 72.4dB SNR, 88dB SFDR 110dB Channel Isolation at 100MHz Flexible Input: 1VP-P to 2VP-P Range 640MHz Full Power Bandwidth S/H Clock Duty Cycle Stabilizer Shutdown and Nap Modes Data Ready Output Clock Pin Compatible Family 125Msps: LTC2283 (12-Bit), LTC2285 (14-Bit) 105Msps: LTC2282 (12-Bit), LTC2284 (14-Bit) 80Msps: LTC2294 (12-Bit), LTC2299 (14-Bit) 65Msps: LTC2293 (12-Bit), LTC2298 (14-Bit) 40Msps: LTC2292 (12-Bit), LTC2297 (14-Bit) 64-Pin (9mm x 9mm) QFN Package The LTC(R)2285 is a 14-bit 125Msps, low power dual 3V A/D converter designed for digitizing high frequency, wide dynamic range signals. The LTC2285 is perfect for demanding imaging and communications applications with AC performance that includes 72.2dB SNR and 82dB SFDR for signals at the Nyquist frequency. Typical DC specs include 1.5LSB INL, 0.6LSB DNL. The transition noise is a low 1.3LSBRMS. A single 3V supply allows low power operation. A separate output supply allows the outputs to drive 0.5V to 3.6V logic. A single-ended CLK input controls converter operation. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles. A data ready output clock (CLKOUT) can be used to latch the output data. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. APPLICATIONS n n n n Wireless and Wired Broadband Communication Imaging Systems Spectral Analysis Portable Instrumentation TYPICAL APPLICATION + ANALOG INPUT A INPUT S/H - SNR vs Input Frequency, -1dB, 2V Range OVDD 14-BIT PIPELINED ADC CORE OUTPUT DRIVERS D13A 75 ** * 74 D0A 73 OGND CLK A OF CLOCK/DUTY CYCLE CONTROL MUX CLK B CLOCK/DUTY CYCLE CONTROL CLKOUT SNR (dBFS) 72 71 70 69 68 67 66 OVDD + ANALOG INPUT B INPUT S/H - 14-BIT PIPELINED ADC CORE OUTPUT DRIVERS D13B ** * 65 0 50 100 150 200 250 300 350 2285 TA01b INPUT FREQUENCY (MHz) D0B OGND 2285 TA01 2285fb 1 LTC2285 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION OVDD = VDD (Notes 1, 2) 64 GND 63 VDD 62 SENSEA 61 VCMA 60 MODE 59 SHDNA 58 OEA 57 OF 56 DA13 55 DA12 54 DA11 53 DA10 52 DA9 51 DA8 50 OGND 49 OVDD TOP VIEW AINA+ 1 AINA- 2 REFHA 3 REFHA 4 REFLA 5 REFLA 6 VDD 7 CLKA 8 CLKB 9 VDD 10 REFLB 11 REFLB 12 REFHB 13 REFHB 14 AINB- 15 AINB+ 16 48 DA7 47 DA6 46 DA5 45 DA4 44 DA3 43 DA2 42 DA1 41 DA0 40 CLKOUT 39 DB13 38 DB12 37 DB11 36 DB10 35 DB9 34 DB8 33 DB7 65 GND 17 VDD 18 SENSEB 19 VCMB 20 MUX 21 SHDNB 22 OEB 23 DB0 24 DB1 25 DB2 26 DB3 27 DB4 28 DB5 29 DB6 30 OGND 31 OVDD 32 Supply Voltage (VDD) ..................................................4V Digital Output Ground Voltage (OGND) ........ -0.3V to 1V Analog Input Voltage (Note 3) .......-0.3V to (VDD + 0.3V) Digital Input Voltage......................-0.3V to (VDD + 0.3V) Digital Output Voltage ................ -0.3V to (OVDD + 0.3V) Power Dissipation .............................................1500mW Operating Temperature Range LTC2285C ................................................ 0C to 70C LTC2285I.............................................. -40C to 85C Storage Temperature Range................... -65C to 150C UP PACKAGE 64-LEAD (9mm x 9mm) PLASTIC QFN TJMAX = 150C, JA = 20C/W EXPOSED PAD (PIN 65) IS GND AND MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2285CUP#PBF LTC2285CUP#TRPBF LTC2285UP 64-Lead (9mm x 9mm) Plastic QFN 0C to 70C LTC2285IUP#PBF LTC2285IUP#TRPBF LTC2285UP 64-Lead (9mm x 9mm) Plastic QFN -40C to 85C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2285CUP LTC2285CUP#TR LTC2285UP 64-Lead (9mm x 9mm) Plastic QFN 0C to 70C LTC2285IUP LTC2285IUP#TR LTC2285UP 64-Lead (9mm x 9mm) Plastic QFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) PARAMETER CONDITIONS MIN Resolution (No Missing Codes) TYP MAX 14 UNITS Bits Integral Linearity Error Differential Analog Input (Note 5) Differential Linearity Error Differential Analog Input -1 0.6 1.1 LSB Offset Error (Note 6) -12 2 12 mV Gain Error External Reference -2.5 0.5 2.5 Offset Drift Full-Scale Drift 1.5 LSB %FS 10 V/C Internal Reference 30 ppm/C External Reference 5 ppm/C 2285fb 2 LTC2285 CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) PARAMETER CONDITIONS Gain Matching External Reference MIN TYP SENSE = 1V UNITS %FS 2 mV 1.3 LSBRMS Offset Matching Transition Noise MAX 0.3 ANALOG INPUT The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) SYMBOL PARAMETER CONDITIONS VIN Analog Input Range (AIN+ -AIN-) MIN 2.85V < VDD < 3.4V (Note 7) VIN,CM Analog Input Common Mode (AIN+ +AIN-)/2 Differential Input Drive (Note 7) Single Ended Input Drive (Note 7) 1 0.5 IIN Analog Input Leakage Current 0V < AIN+, AIN- < VDD ISENSE SENSEA, SENSEB Input Leakage 0V < SENSEA, SENSEB < 1V IMODE MODE Input Leakage Current 0V < MODE < VDD TYP MAX UNITS 0.5V to 1V 1.5 1.5 V 1.9 2 V V -1 1 A -3 3 A -3 3 A tAP Sample-and-Hold Acquisition Delay Time tJITTER Sample-and-Hold Acquisition Delay Time Jitter 0.2 psRMS CMRR Analog Input Common Mode Rejection Ratio 80 dB 640 MHz Full Power Bandwidth 0 Figure 8 Test Circuit ns DYNAMIC ACCURACY The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. AIN = -1dBFS. (Note 4) SYMBOL PARAMETER CONDITIONS SNR Signal-to-Noise Ratio 5MHz Input MIN 30MHz Input Spurious Free Dynamic Range 4th Harmonic or Higher dB 71.7 dB 5MHz Input 88 dB 30MHz Input 85 dB 82 dB 68.9 70 140MHz Input 78 dB 5MHz Input 90 dB 30MHz Input 90 dB 90 dB 90 dB 5MHz Input 72.2 dB 30MHz Input 72 dB 71.9 dB 70.2 dB 85 dB -110 dB 70MHz Input 77 140MHz Input S/(N+D) Signal-to-Noise Plus Distortion Ratio 70MHz Input 140MHz Input IMD dB dB 70MHz Input SFDR UNITS 72.3 140MHz Input Spurious Free Dynamic Range 2nd or 3rd Harmonic MAX 72.2 70MHz Input SFDR TYP 72.4 Intermodulation Distortion fIN = 40MHz, 41MHz Crosstalk fIN = 100MHz 67 2285fb 3 LTC2285 INTERNAL REFERENCE CHARACTERISTICS (Note 4) PARAMETER CONDITIONS MIN TYP MAX UNITS VCM Output Voltage IOUT = 0 1.475 1.500 1.525 V VCM Output Tempco 25 ppm/C VCM Line Regulation 2.85V < VDD < 3.4V 3 mV/V VCM Output Resistance |IOUT| < 1mA 4 DIGITAL INPUTS AND DIGITAL OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS LOGIC INPUTS (CLK, OE, SHDN, MUX) VIH High Level Input Voltage VDD = 3V VIL Low Level Input Voltage VDD = 3V IIN Input Current VIN = 0V to VDD CIN Input Capacitance (Note 7) COZ Hi-Z Output Capacitance OE = High (Note 7) 3 pF ISOURCE Output Source Current VOUT = 0V 50 mA ISINK Output Sink Current VOUT = 3V 50 mA VOH High Level Output Voltage IO = -10A IO = -200A IO = 10A IO = 1.6mA 2 V -10 0.8 V 10 A 3 pF LOGIC OUTPUTS OVDD = 3V VOL Low Level Output Voltage 2.7 2.995 2.99 0.005 0.09 V V 0.4 V V OVDD = 2.5V VOH High Level Output Voltage IO = -200A 2.49 V VOL Low Level Output Voltage IO = 1.6mA 0.09 V VOH High Level Output Voltage IO = -200A 1.79 V VOL Low Level Output Voltage IO = 1.6mA 0.09 V OVDD = 1.8V 2285fb 4 LTC2285 POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 8) SYMBOL PARAMETER CONDITIONS MIN TYP MAX VDD Analog Supply Voltage (Note 9) 2.85 3 3.4 0.5 UNITS V OVDD Output Supply Voltage (Note 9) 3 3.6 V IVDD Supply Current Both ADCs at fS(MAX) 263 305 mA PDISS Power Dissipation Both ADCs at fS(MAX) 790 915 mW PSHDN Shutdown Power (Each Channel) SHDN = H, OE = H, No CLK 2 mW PNAP Nap Mode Power (Each Channel) SHDN = H, OE = L, No CLK 15 mW TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4) SYMBOL PARAMETER CONDITIONS MIN fs Sampling Frequency (Note 9) 1 tL CLK Low Time Duty Cycle Stabilizer Off (Note 7) Duty Cycle Stabilizer On (Note 7) 3.8 3 tH CLK High Time Duty Cycle Stabilizer Off (Note 7) Duty Cycle Stabilizer On (Note 7) 3.8 3 tAP Sample-and-Hold Aperture Delay TYP MAX UNITS 125 MHz 4 4 500 500 ns ns 4 4 500 500 ns ns 0 ns tD CLK to DATA Delay CL = 5pF (Note 7) 1.4 2.7 5.4 ns tC CLK to CLKOUT Delay CL = 5pF (Note 7) 1.4 2.7 5.4 ns DATA to CLKOUT Skew (tD - tC) (Note 7) -0.6 0 0.6 ns tMD MUX to DATA Delay CL = 5pF (Note 7) 1.4 2.7 5.4 ns Data Access Time After OE CL = 5pF (Note 7) 4.3 10 ns BUS Relinquish Time (Note 7) 3.3 8.5 Pipeline Latency Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: VDD = 3V, fSAMPLE = 125MHz, input range = 2VP-P with differential drive, unless otherwise noted. 5 ns Cycles Note 5: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 6: Offset error is the offset voltage measured from -0.5 LSB when the output code flickers between 00 0000 0000 0000 and 11 1111 1111 1111. Note 7: Guaranteed by design, not subject to test. Note 8: VDD = 3V, fSAMPLE = 125MHz, input range = 1VP-P with differential drive. The supply current and power dissipation are the sum total for both channels with both channels active. Note 9: Recommended operating conditions. 2285fb 5 LTC2285 TYPICAL PERFORMANCE CHARACTERISTICS Crosstalk vs Input Frequency Typical INL, 2V Range, 125Msps -100 0.8 1.5 -105 0.6 -110 -115 -120 DNL ERROR (LSB) INL ERROR (LSB) 1.0 CROSSTALK (dB) Typical DNL, 2V Range, 125Msps 1.0 2.0 0.5 0 -0.5 -1.0 -125 20 40 60 80 INPUT FREQUENCY (MHz) 100 2285 G01 12288 0 16384 0 -10 -20 -20 -20 -30 -30 -30 -60 -70 -80 AMPLITUDE (dB) 0 -10 -50 -40 -50 -60 -70 -80 -60 -70 -80 -90 -100 -100 -100 -110 -110 -110 -120 -120 20 30 40 FREQUENCY (MHz) 50 60 0 10 2285 G04 20 30 40 FREQUENCY (MHz) 50 -120 60 0 20000 -10 18000 -20 -20 -30 -30 -70 -80 -50 -60 -70 -100 -100 -120 0 60 2285 G07 3380 4000 -110 50 10516 6000 -120 20 30 40 FREQUENCY (MHz) 11299 10000 -110 10 17646 18027 12000 2000 0 60 2285 G06 8000 -80 -90 50 14000 -40 -90 20 30 40 FREQUENCY (MHz) 16000 COUNT AMPLITUDE (dB) 0 -60 10 Grounded Input Histogram, 125Msps -10 -50 0 2285 G05 8192 Point 2-Tone FFT, fIN = 28.2MHz and 26.8MHz, -1dB, 2V Range, 125Msps -40 16384 2285 G03 -50 -90 10 12288 -40 -90 0 8192 CODE 8192 Point FFT, fIN = 70MHz, -1dB, 2V Range, 125Msps 0 -40 4096 2285 G02 -10 AMPLITUDE (dB) AMPLITUDE (dB) 8192 CODE 8192 Point FFT, fIN = 30MHz, -1dB, 2V Range, 125Msps 8192 Point FFT, fIN = 140MHz, -1dB, 2V Range, 125Msps AMPLITUDE (dB) -0.4 -1.0 4096 0 8192 Point FFT, fIN = 5MHz, -1dB, 2V Range, 125Msps 0 -0.2 -0.8 -2.0 0 0.2 -0.6 -1.5 -130 0.4 0 10 20 30 40 FREQUENCY (MHz) 50 60 2285 G08 3316 3 54 581 8183 8185 637 68 1 8187 8189 CODE 8191 8193 2285 G09 2285fb 6 LTC2285 TYPICAL PERFORMANCE CHARACTERISTICS SNR vs Input Frequency, -1dB, 2V Range, 125Msps SFDR vs Input Frequency, -1dB, 2V Range, 125Msps 75 SNR and SFDR vs Sample Rate, 2V Range, fIN = 5MHz, -1dB 100 74 90 SFDR 95 90 SFDR (dBRS) 71 70 69 85 80 68 75 67 80 SNR 70 60 70 66 65 65 0 50 0 100 150 200 250 300 350 2285 G10 INPUT FREQUENCY (MHz) 0 SFDR (dBc AND dBFS) dBc 40 30 20 10 -40 -30 -20 INPUT LEVEL (dBFS) -50 -10 0 2285 G13 280 dBFS 90 50 40 60 80 100 120 140 160 2285 G12 SAMPLE RATE (Msps) 290 100 60 20 IVDD vs Sample Rate, 5MHz Sine Wave Input, -1dB 110 dBFS 70 270 80 260 70 60 dBc 50 40 250 2V RANGE 240 1V RANGE 230 220 30 20 210 10 200 0 -80 -70 -60 -50 -40 -30 -20 -10 0 2285 G14 INPUT LEVEL (dBFS) IOVDD vs Sample Rate, 5MHz Sine Wave Input, -1dB, 0VDD = 1.8V 190 0 20 60 80 100 40 SAMPLE RATE (Msps) 120 140 2285 G15 SNR vs SENSE, fIN = 5MHz, -1dB 74 16 73 14 72 12 71 10 SNR (dBFS) IOVDD (mA) 0 -70 -60 50 100 150 200 250 300 350 2285 G11 INPUT FREQUENCY (MHz) SFDR vs Input Level, fIN = 70MHz, 2V Range, 125Msps SNR vs Input Level, fIN = 70MHz, 2V Range, 125Msps 80 50 IVDD (mA) SNR (dBFS) 72 SNR (dBc AND dBFS) SNR AND SFDR (dBFS) 73 8 6 70 69 68 67 4 66 2 65 0 64 0 20 80 100 60 SAMPLE RATE (Msps) 40 120 140 2285 G16 0.4 0.5 0.6 0.7 0.8 0.9 SENSE PIN (V) 1.0 1.1 2285 G17 2285fb 7 LTC2285 PIN FUNCTIONS AINA+ (Pin 1): Channel A Positive Differential Analog Input. AINA- (Pin 2): Channel A Negative Differential Analog Input. REFHA (Pins 3, 4): Channel A High Reference. Short together and bypass to Pins 5, 6 with a 0.1F ceramic chip capacitor as close to the pin as possible. Also bypass to Pins 5, 6 with an additional 2.2F ceramic chip capacitor and to ground with a 1F ceramic chip capacitor. REFLA (Pins 5, 6): Channel A Low Reference. Short together and bypass to Pins 3, 4 with a 0.1F ceramic chip capacitor as close to the pin as possible. Also bypass to Pins 3, 4 with an additional 2.2F ceramic chip capacitor and to ground with a 1F ceramic chip capacitor. VDD (Pins 7, 10, 18, 63): Analog 3V Supply. Bypass to GND with 0.1F ceramic chip capacitors. CLKA (Pin 8): Channel A Clock Input. The input sample starts on the positive edge. CLKB (Pin 9): Channel B Clock Input. The input sample starts on the positive edge. REFLB (Pins 11, 12): Channel B Low Reference. Short together and bypass to Pins 13, 14 with a 0.1F ceramic chip capacitor as close to the pin as possible. Also bypass to Pins 13, 14 with an additional 2.2F ceramic chip capacitor and to ground with a 1F ceramic chip capacitor. REFHB (Pins 13, 14): Channel B High Reference. Short together and bypass to Pins 11, 12 with a 0.1F ceramic chip capacitor as close to the pin as possible. Also bypass to Pins 11, 12 with an additional 2.2F ceramic chip capacitor and to ground with a 1F ceramic chip capacitor. AINB- (Pin 15): Channel B Negative Differential Analog Input. AINB+ (Pin 16): Channel B Positive Differential Analog Input. and a 1V input range. An external reference greater than 0.5V and less than 1V applied to SENSEB selects an input range of VSENSEB. 1V is the largest valid input range. VCMB (Pin 20): Channel B 1.5V Output and Input Common Mode Bias. Bypass to ground with 2.2F ceramic chip capacitor. Do not connect to VCMA. MUX (Pin 21): Digital Output Multiplexer Control. If MUX is High, Channel A comes out on DA0-DA13; Channel B comes out on DB0-DB13. If MUX is Low, the output busses are swapped and Channel A comes out on DB0-DB13; Channel B comes out on DA0-DA13. To multiplex both channels onto a single output bus, connect MUX, CLKA and CLKB together. (This is not recommended at clock frequencies above 80Msps.) SHDNB (Pin 22): Channel B Shutdown Mode Selection Pin. Connecting SHDNB to GND and OEB to GND results in normal operation with the outputs enabled. Connecting SHDNB to GND and OEB to VDD results in normal operation with the outputs at high impedance. Connecting SHDNB to VDD and OEB to GND results in nap mode with the outputs at high impedance. Connecting SHDNB to VDD and OEB to VDD results in sleep mode with the outputs at high impedance. OEB (Pin 23): Channel B Output Enable Pin. Refer to SHDNB pin function. DB0 - DB13 (Pins 24 to 30, 33 to 39): Channel B Digital Outputs. DB13 is the MSB. OGND (Pins 31, 50): Output Driver Ground. OVDD (Pins 32, 49): Positive Supply for the Output Drivers. Bypass to ground with 0.1F ceramic chip capacitor. CLKOUT (Pin 40): Data Ready Clock Output. Latch data on the falling edge of CLKOUT. CLKOUT is derived from CLKB. Tie CLKA to CLKB for simultaneous operation. DA0 - DA13 (Pins 41 to 48, 51 to 56): Channel A Digital Outputs. DA13 is the MSB. GND (Pins 17, 64): ADC Power Ground. OF (Pin 57): Overflow/Underflow Output. High when an overflow or underflow has occurred on either channel A or channel B. SENSEB (Pin 19): Channel B Reference Programming Pin. Connecting SENSEB to VCMB selects the internal reference and a 0.5V input range. VDD selects the internal reference OEA (Pin 58): Channel A Output Enable Pin. Refer to SHDNA pin function. 8 2285fb LTC2285 PIN FUNCTIONS SHDNA (Pin 59): Channel A Shutdown Mode Selection Pin. Connecting SHDNA to GND and OEA to GND results in normal operation with the outputs enabled. Connecting SHDNA to GND and OEA to VDD results in normal operation with the outputs at high impedance. Connecting SHDNA to VDD and OEA to GND results in nap mode with the outputs at high impedance. Connecting SHDNA to VDD and OEA to VDD results in sleep mode with the outputs at high impedance. stabilizer on. VDD selects 2's complement output format and turns the clock duty cycle stabilizer off. VCMA (Pin 61): Channel A 1.5V Output and Input Common Mode Bias. Bypass to ground with 2.2F ceramic chip capacitor. Do not connect to VCMB. SENSEA (Pin 62): Channel A Reference Programming Pin. Connecting SENSEA to VCMA selects the internal reference and a 0.5V input range. VDD selects the internal reference and a 1V input range. An external reference greater than 0.5V and less than 1V applied to SENSEA selects an input range of VSENSEA. 1V is the largest valid input range. MODE (Pin 60): Output Format and Clock Duty Cycle Stabilizer Selection Pin. Note that MODE controls both channels. Connecting MODE to GND selects offset binary output format and turns the clock duty cycle stabilizer off. 1/3 VDD selects offset binary output format and turns the clock duty cycle stabilizer on. 2/3 VDD selects 2's complement output format and turns the clock duty cycle GND (Exposed Pad) (Pin 65): ADC Power Ground. The Exposed Pad on the bottom of the package needs to be soldered to ground. FUNCTIONAL BLOCK DIAGRAM AIN+ AIN- VCM INPUT S/H FIRST PIPELINED ADC STAGE SECOND PIPELINED ADC STAGE THIRD PIPELINED ADC STAGE FOURTH PIPELINED ADC STAGE FIFTH PIPELINED ADC STAGE 1.5V REFERENCE SIXTH PIPELINED ADC STAGE SHIFT REGISTER AND CORRECTION 2.2F RANGE SELECT REFH SENSE REFL INTERNAL CLOCK SIGNALS OVDD REF BUF OF* D13 CLOCK/DUTY CYCLE CONTROL DIFF REF AMP CONTROL LOGIC * * * OUTPUT DRIVERS D0 CLKOUT* REFH 0.1F 2285 F01 REFL OGND CLK MODE SHDN OE 2.2F *OF AND CLKOUT ARE SHARED BETWEEN BOTH CHANNELS. 1F 1F Figure 1. Functional Block Diagram (Only One Channel is Shown) 2285fb 9 LTC2285 TIMING DIAGRAMS Dual Digital Output Bus Timing (Only One Channel is Shown) tAP ANALOG INPUT N+4 N+2 N N+1 tH N+3 N+5 tL CLKA = CLKB tD N-4 N-5 D0-D13, OF N-3 N-2 N-1 N 2284 TD01 tC CLKOUT Multiplexed Digital Output Bus Timing tAPA ANALOG INPUT A A+4 A+2 A A+1 A+3 tAPB ANALOG INPUT B B+4 B+2 B B+1 tH tL A-5 B-5 B+3 CLKA = CLKB = MUX D0A-D13A A-4 tD D0B-D13B B-5 tC B-4 A-3 B-3 A-2 B-2 B-3 A-3 B-2 A-2 A-1 tMD A-5 B-4 A-4 B-1 2284 TD02 CLKOUT 2285fb 10 LTC2285 APPLICATIONS INFORMATION DYNAMIC PERFORMANCE Signal-to-Noise Plus Distortion Ratio The signal-to-noise plus distortion ratio [S/(N + D)] is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the ADC output. The output is band limited to frequencies above DC to below half the sampling frequency. 2fa + fb, 2fb + fa, 2fa - fb and 2fb - fa. The intermodulation distortion is defined as the ratio of the RMS value of either input tone to the RMS value of the largest 3rd order intermodulation product. Spurious Free Dynamic Range (SFDR) Spurious free dynamic range is the peak harmonic or spurious noise that is the largest spectral component excluding the input signal and DC. This value is expressed in decibels relative to the RMS value of a full-scale input signal. Signal-to-Noise Ratio The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components except the first five harmonics and DC. Input Bandwidth Total Harmonic Distortion Aperture Delay Time Total harmonic distortion is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency. THD is expressed as: The time from when CLK reaches midsupply to the instant that the input signal is held by the sample and hold circuit. THD = 20log (V22 + V32 + V42 + ...Vn2 )/V1 where V1 is the RMS amplitude of the fundamental frequency and V2 through Vn are the amplitudes of the second through nth harmonics. The THD calculated in this data sheet uses all the harmonics up to the fifth. Intermodulation Distortion If the ADC input signal consists of more than one spectral component, the ADC transfer function nonlinearity can produce intermodulation distortion (IMD) in addition to THD. IMD is the change in one sinusoidal input caused by the presence of another sinusoidal input at a different frequency. If two pure sine waves of frequencies fa and fb are applied to the ADC input, nonlinearities in the ADC transfer function can create distortion products at the sum and difference frequencies of mfa nfb, where m and n = 0, 1, 2, 3, etc. The 3rd order intermodulation products are The input bandwidth is that input frequency at which the amplitude of the reconstructed fundamental is reduced by 3dB for a full scale input signal. Aperture Delay Jitter The variation in the aperture delay time from conversion to conversion. This random variation will result in noise when sampling an AC input. The signal to noise ratio due to the jitter alone will be: SNRJITTER = -20log (2 * fIN * tJITTER) Crosstalk Crosstalk is the coupling from one channel (being driven by a full-scale signal) onto the other channel (being driven by a -1dBFS signal). CONVERTER OPERATION As shown in Figure 1, the LTC2285 is a dual CMOS pipelined multistep converter. The converter has six pipelined ADC stages; a sampled analog input will result in a digitized value five cycles later (see the Timing Diagram section). For optimal AC performance the analog inputs should be driven differentially. For cost sensitive applications, the analog inputs can be driven single-ended 2285fb 11 LTC2285 APPLICATIONS INFORMATION with slightly worse harmonic distortion. The CLK input is single-ended. The LTC2285 has two phases of operation, determined by the state of the CLK input pin. third stage. An identical process is repeated for the third, fourth and fifth stages, resulting in a fifth stage residue that is sent to the sixth stage ADC for final evaluation. Each pipelined stage shown in Figure 1 contains an ADC, a reconstruction DAC and an interstage residue amplifier. In operation, the ADC quantizes the input to the stage and the quantized value is subtracted from the input by the DAC to produce a residue. The residue is amplified and output by the residue amplifier. Successive stages operate out of phase so that when the odd stages are outputting their residue, the even stages are acquiring that residue and vice versa. Each ADC stage following the first has additional range to accommodate flash and amplifier offset errors. Results from all of the ADC stages are digitally synchronized such that the results can be properly combined in the correction logic before being sent to the output buffer. When CLK is low, the analog input is sampled differentially directly onto the input sample-and-hold capacitors, inside the "Input S/H" shown in the Block Diagram. At the instant that CLK transitions from low to high, the sampled input is held. While CLK is high, the held input voltage is buffered by the S/H amplifier which drives the first pipelined ADC stage. The first stage acquires the output of the S/H during this high phase of CLK. When CLK goes back low, the first stage produces its residue which is acquired by the second stage. At the same time, the input S/H goes back to acquiring the analog input. When CLK goes back high, the second stage produces its residue which is acquired by the Figure 2 shows an equivalent circuit for the LTC2285 CMOS differential sample-and-hold. The analog inputs are connected to the sampling capacitors (CSAMPLE) through NMOS transistors. The capacitors shown attached to each input (CPARASITIC) are the summation of all other capacitance associated with each input. SAMPLE/HOLD OPERATION AND INPUT DRIVE Sample/Hold Operation During the sample phase when CLK is low, the transistors connect the analog inputs to the sampling capacitors and they charge to and track the differential input voltage. When CLK transitions from low to high, the sampled input voltage is held on the sampling capacitors. During the hold phase when CLK is high, the sampling capacitors are disconnected LTC2285 VDD AIN+ CSAMPLE 3.5pF 15 CPARASITIC 1pF VDD AIN- CSAMPLE 3.5pF 15 CPARASITIC 1pF VDD CLK 2285 F02 Figure 2. Equivalent Input Circuit 2285fb 12 LTC2285 APPLICATIONS INFORMATION from the input and the held voltage is passed to the ADC core for processing. As CLK transitions from high to low, the inputs are reconnected to the sampling capacitors to acquire a new sample. Since the sampling capacitors still hold the previous sample, a charging glitch proportional to the change in voltage between samples will be seen at this time. If the change between the last sample and the new sample is small, the charging glitch seen at the input will be small. If the input change is large, such as the change seen with input frequencies near Nyquist, then a larger charging glitch will be seen. Single-Ended Input For cost sensitive applications, the analog inputs can be driven single-ended. With a single-ended input the harmonic distortion and INL will degrade, but the SNR and DNL will remain unchanged. For a single-ended input, AIN+ should be driven with the input signal and AIN- should be connected to 1.5V or VCM. Common Mode Bias For optimal performance the analog inputs should be driven differentially. Each input should swing 0.5V for the 2V range or 0.25V for the 1V range, around a common mode voltage of 1.5V. The VCM output pin may be used to provide the common mode bias level. VCM can be tied directly to the center tap of a transformer to set the DC input level or as a reference level to an op amp differential driver circuit. The VCM pin must be bypassed to ground close to the ADC with a 2.2F or greater capacitor. Input Drive Impedance As with all high performance, high speed ADCs, the dynamic performance of the LTC2285 can be influenced by the input drive circuitry, particularly the second and third harmonics. Source impedance and reactance can influence SFDR. At the falling edge of CLK, the sample-and-hold circuit will connect the 3.5pF sampling capacitor to the input pin and start the sampling period. The sampling period ends when CLK rises, holding the sampled input on the sampling capacitor. Ideally the input circuitry should be fast enough to fully charge the sampling capacitor during the sampling period 1/(2FENCODE); however, this is not always possible and the incomplete settling may degrade the SFDR. The sampling glitch has been designed to be as linear as possible to minimize the effects of incomplete settling. For the best performance, it is recommended to have a source impedance of 100 or less for each input. The source impedance should be matched for the differential inputs. Poor matching will result in higher even order harmonics, especially the second. Input Drive Circuits Figure 3 shows the LTC2285 being driven by an RF transformer with a center tapped secondary. The secondary center tap is DC biased with VCM, setting the ADC input signal at its optimum DC level. Terminating on the transformer secondary is desirable, as this provides a common mode path for charging glitches caused by the sample and hold. Figure 3 shows a 1:1 turns ratio transformer. Other turns ratios can be used if the source impedance seen by the ADC does not exceed 100 for each ADC input. A disadvantage of using a transformer is the loss of low frequency response. Most small RF transformers have poor performance at frequencies below 1MHz. VCM 2.2F 0.1F ANALOG INPUT T1 1:1 25 25 AIN+ LTC2285 0.1F 12pF 25 AIN- T1 = MA/COM ETC1-1T 25 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 2285 F03 Figure 3. Single-Ended to Differential Conversion Using a Transformer 2285fb 13 LTC2285 APPLICATIONS INFORMATION VCM HIGH SPEED DIFFERENTIAL 25 AMPLIFIER ANALOG INPUT + 2.2F 2.2F 0.1F + AIN LTC2285 12 ANALOG INPUT 25 + CM - VCM - 25 0.1F AIN- LTC2285 0.1F T1 12pF AIN+ 8pF 25 12 AIN- T1 = MA/COM, ETC 1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 2285 F04 2285 F06 Figure 4. Differential Drive with an Amplifier Figure 6. Recommended Front End Circuit for Input Frequencies Between 70MHz and 170MHz VCM 1k 0.1F ANALOG INPUT 2.2F 1k 25 AIN+ VCM LTC2285 2.2F 0.1F 12pF 25 AIN- 0.1F AIN+ ANALOG INPUT 25 T1 2285 F05 0.1F Figure 5 shows a single-ended input circuit. The impedance seen by the analog inputs should be matched. This circuit is not recommended if low distortion is required. The 25 resistors and 12pF capacitor on the analog inputs serve two purposes: isolating the drive circuitry from the sample-and-hold charging glitches and limiting the wideband noise at the converter input. For input frequencies above 70MHz, the input circuits of Figure 6, 7 and 8 are recommended. The balun transformer gives better high frequency response than a flux coupled center tapped transformer. The coupling capacitors allow the analog inputs to be DC biased at 1.5V. In Figure 8, the series inductors are impedance matching elements that maximize the ADC bandwidth. 25 T1 = MA/COM, ETC 1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE Figure 5. Single-Ended Drive Figure 4 demonstrates the use of a differential amplifier to convert a single ended input signal into a differential input signal. The advantage of this method is that it provides low frequency input response; however, the limited gain bandwidth of most op amps will limit the SFDR at high input frequencies. LTC2285 0.1F AIN- 2285 F07 Figure 7. Recommended Front End Circuit for Input Frequencies Between 170MHz and 300MHz VCM 2.2F 0.1F 8.2nH ANALOG INPUT 25 AIN+ LTC2285 0.1F T1 0.1F 25 8.2nH - AIN T1 = MA/COM, ETC 1-1-13 RESISTORS, CAPACITORS, INDUCTORS ARE 0402 PACKAGE SIZE 2285 F08 Figure 8. Recommended Front End Circuit for Input Frequencies Above 300MHz 2285fb 14 LTC2285 APPLICATIONS INFORMATION Reference Operation Figure 9 shows the LTC2285 reference circuitry consisting of a 1.5V bandgap reference, a difference amplifier and switching and control circuit. The internal voltage reference can be configured for two pin selectable input ranges of 2V (1V differential) or 1V (0.5V differential). Tying the SENSE pin to VDD selects the 2V range; tying the SENSE pin to VCM selects the 1V range. The 1.5V bandgap reference serves two functions: its output provides a DC bias point for setting the common mode voltage of any external input circuitry; additionally, the reference is used with a difference amplifier to generate the differential reference levels needed by the internal ADC circuitry. An external bypass capacitor is required for the 1.5V reference output, VCM. This provides a high frequency low impedance path to ground for internal and external circuitry. LTC2285 1.5V VCM 4 The difference amplifier generates the high and low reference for the ADC. High speed switching circuits are connected to these outputs and they must be externally bypassed. Each output has two pins. The multiple output pins are needed to reduce package inductance. Bypass capacitors must be connected as shown in Figure 9. Each ADC channel has an independent reference with its own bypass capacitors. The two channels can be used with the same or different input ranges. Other voltage ranges between the pin selectable ranges can be programmed with two external resistors as shown in Figure 10. An external reference can be used by applying its output directly or through a resistor divider to SENSE. It is not recommended to drive the SENSE pin with a logic device. The SENSE pin should be tied to the appropriate level as close to the converter as possible. If the SENSE pin is driven externally, it should be bypassed to ground as close to the device as possible with a 1F ceramic capacitor. For the best channel matching, connect an external reference to SENSEA and SENSEB. 1.5V BANDGAP REFERENCE 1.5V 2.2F 1V 0.5V VCM 2.2F 12k TIE TO VDD FOR 2V RANGE; TIE TO VCM FOR 1V RANGE; RANGE = 2 * VSENSE FOR 0.5V < VSENSE < 1V RANGE DETECT AND CONTROL 0.75V 12k 1F SENSE 2285 F10 BUFFER Figure 10. 1.5V Range ADC INTERNAL ADC HIGH REFERENCE 1F REFH 2.2F LTC2285 SENSE 0.1F Input Range The input range can be set based on the application. The 2V input range will provide the best signal-to-noise performance while maintaining excellent SFDR. The 1V input range will have better SFDR performance, but the SNR will degrade by 5.7dB. See the Typical Performance Characteristics section. DIFF AMP 1F REFL INTERNAL ADC LOW REFERENCE 2285 F09 Figure 9. Equivalent Reference Circuit Driving the Clock Input The CLK inputs can be driven directly with a CMOS or TTL level signal. A sinusoidal clock can also be used along with a low jitter squaring circuit before the CLK pin (Figure 11). 2285fb 15 LTC2285 APPLICATIONS INFORMATION CLEAN SUPPLY 4.7F CLEAN SUPPLY 4.7F FERRITE BEAD FERRITE BEAD 0.1F 0.1F SINUSOIDAL CLOCK INPUT CLK 1k 0.1F CLK 50 1k LTC2285 LTC2285 100 NC7SVU04 2285 F12 2285 F11 Figure 11. Sinusoidal Single-Ended CLK Drive The noise performance of the LTC2285 can depend on the clock signal quality as much as on the analog input. Any noise present on the clock signal will result in additional aperture jitter that will be RMS summed with the inherent ADC aperture jitter. In applications where jitter is critical, such as when digitizing high input frequencies, use as large an amplitude as possible. Also, if the ADC is clocked with a sinusoidal signal, filter the CLK signal to reduce wideband noise and distortion products generated by the source. It is recommended that CLKA and CLKB are shorted together and driven by the same clock source. If a small time delay is desired between when the two channels sample the analog inputs, CLKA and CLKB can be driven by two different signals. If this delay exceeds 1ns, the performance of the part may degrade. CLKA and CLKB should not be driven by asynchronous signals. Figures 12 and 13 show alternatives for converting a differential clock to the single-ended CLK input. The use of a transformer provides no incremental contribution to phase noise. The LVDS or PECL to CMOS translators provide little degradation below 70MHz, but at 140MHz will degrade the SNR compared to the transformer solution. The nature of the received signals also has a large bearing on how much SNR degradation will be experienced. For high crest factor signals such as WCDMA or OFDM, where the nominal power level must be at least 6dB to 8dB below full scale, the use of these translators will have a lesser impact. IF LVDS USE FIN1002 OR FIN1018. FOR PECL, USE AZ1000ELT21 OR SIMILAR Figure 12. CLK Drive Using an LVDS or PECL to CMOS Converter ETC1-1T CLK LTC2285 5pF-30pF DIFFERENTIAL CLOCK INPUT 2285 F13 0.1F FERRITE BEAD VCM Figure 13. LVDS or PECL CLK Drive Using a Transformer The transformer in the example may be terminated with the appropriate termination for the signaling in use. The use of a transformer with a 1:4 impedance ratio may be desirable in cases where lower voltage differential signals are considered. The center tap may be bypassed to ground through a capacitor close to the ADC if the differential signals originate on a different plane. The use of a capacitor at the input may result in peaking, and depending on transmission line length may require a 10 to 20 ohm series resistor to act as both a low pass filter for high frequency noise that may be induced into the clock line by neighboring digital signals, as well as a damping mechanism for reflections. Maximum and Minimum Conversion Rates The maximum conversion rate for the LTC2285 is 125Msps. The lower limit of the LTC2285 sample rate is determined by droop of the sample-and-hold circuits. The pipelined architecture of this ADC relies on storing analog signals on 2285fb 16 LTC2285 APPLICATIONS INFORMATION small valued capacitors. Junction leakage will discharge the capacitors. The specified minimum operating frequency for the LTC2285 is 1Msps. Clock Duty Cycle Stabilizer An optional clock duty cycle stabilizer circuit ensures high performance even if the input clock has a non 50% duty cycle. Using the clock duty cycle stabilizer is recommended for most applications. To use the clock duty cycle stabilizer, the MODE pin should be connected to 1/3VDD or 2/3VDD using external resistors. This circuit uses the rising edge of the CLK pin to sample the analog input. The falling edge of CLK is ignored and the internal falling edge is generated by a phase-locked loop. The input clock duty cycle can vary from 40% to 60% and the clock duty cycle stabilizer will maintain a constant 50% internal duty cycle. If the clock is turned off for a long period of time, the duty cycle stabilizer circuit will require a hundred clock cycles for the PLL to lock onto the input clock. For applications where the sample rate needs to be changed quickly, the clock duty cycle stabilizer can be disabled. If the duty cycle stabilizer is disabled, care should be taken to make the sampling clock have a 50% (5%) duty cycle. Digital Output Buffers Figure 14 shows an equivalent circuit for a single output buffer. Each buffer is powered by OVDD and OGND, isolated from the ADC power and ground. The additional N-channel transistor in the output driver allows operation down to low voltages. The internal resistor in series with the output makes the output appear as 50 to external circuitry and may eliminate the need for external damping resistors. As with all high speed/high resolution converters, the digital output loading can affect the performance. The digital outputs of the LTC2285 should drive a minimal capacitive load to avoid possible interaction between the digital outputs and sensitive input circuitry. For full speed operation the capacitive load should be kept under 10pF. Lower OVDD voltages will also help reduce interference from the digital outputs. LTC2283 OVDD VDD 0.5V TO 3.6V VDD 0.1F OVDD DATA FROM LATCH PREDRIVER LOGIC 43 TYPICAL DATA OUTPUT OE DIGITAL OUTPUTS OGND Table 1 shows the relationship between the analog input voltage, the digital data bits, and the overflow bit. Note that OF is high when an overflow or underflow has occurred on either channel A or channel B. 2283 F14 Figure 14. Digital Output Buffer Data Format Table 1. Output Codes vs Input Voltage AIN+ - AIN- (2V Range) OF D13 - D0 (Offset Binary) D13 - D0 (2's Complement) >+1.000000V +0.999878V +0.999756V 1 0 0 11 1111 1111 1111 11 1111 1111 1111 11 1111 1111 1110 01 1111 1111 1111 01 1111 1111 1111 01 1111 1111 1110 +0.000122V 0.000000V -0.000122V -0.000244V 0 0 0 0 10 0000 0000 0001 10 0000 0000 0000 01 1111 1111 1111 01 1111 1111 1110 00 0000 0000 0001 00 0000 0000 0000 11 1111 1111 1111 11 1111 1111 1110 -0.999878V -1.000000V <-1.000000V 0 0 1 00 0000 0000 0001 00 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0001 10 0000 0000 0000 10 0000 0000 0000 Using the MODE pin, the LTC2285 parallel digital output can be selected for offset binary or 2's complement format. Connecting MODE to GND or 1/3VDD selects offset binary output format. Connecting MODE to 2/3VDD or VDD selects 2's complement output format. An external resistor divider can be used to set the 1/3VDD or 2/3VDD logic values. Table 2 shows the logic states for the MODE pin. 2285fb 17 LTC2285 APPLICATIONS INFORMATION Sleep and Nap Modes Table 2. MODE Pin Function OUTPUT FORMAT CLOCK DUTY CYCLE STABILIZER 0 Offset Binary Off 1/3VDD Offset Binary On 2/3VDD 2's Complement On VDD 2's Complement Off MODE PIN Overflow Bit When OF outputs a logic high the converter is either overranged or underranged on channel A or channel B. Note that both channels share a common OF pin, which is not the case for slower pin compatible parts such as the LTC2284 or LTC2299. OF is disabled when channel A is in sleep or nap mode. Output Clock The ADC has a delayed version of the CLKB input available as a digital output, CLKOUT. The falling edge of the CLKOUT pin can be used to latch the digital output data. CLKOUT is disabled when channel B is in sleep or nap mode. Output Driver Power Separate output power and ground pins allow the output drivers to be isolated from the analog circuitry. The power supply for the digital output buffers, OVDD, should be tied to the same power supply as for the logic being driven. For example, if the converter is driving a DSP powered by a 1.8V supply, then OVDD should be tied to that same 1.8V supply. OVDD can be powered with any voltage from 500mV up to 3.6V. OGND can be powered with any voltage from GND up to 1V and must be less than OVDD. The logic outputs will swing between OGND and OVDD. Output Enable The outputs may be disabled with the output enable pin, OE. OE high disables all data outputs including OF. The data access and bus relinquish times are too slow to allow the outputs to be enabled and disabled during full speed operation. The output Hi-Z state is intended for use during long periods of inactivity. Channels A and B have independent output enable pins (OEA, OEB). The converter may be placed in shutdown or nap modes to conserve power. Connecting SHDN to GND results in normal operation. Connecting SHDN to VDD and OE to VDD results in sleep mode, which powers down all circuitry including the reference and typically dissipates 1mW. When exiting sleep mode it will take milliseconds for the output data to become valid because the reference capacitors have to recharge and stabilize. Connecting SHDN to VDD and OE to GND results in nap mode, which typically dissipates 30mW. In nap mode, the on-chip reference circuit is kept on, so that recovery from nap mode is faster than that from sleep mode, typically taking 100 clock cycles. In both sleep and nap modes, all digital outputs are disabled and enter the Hi-Z state. Channels A and B have independent SHDN pins (SHDNA, SHDNB). Channel A is controlled by SHDNA and OEA, and channel B is controlled by SHDNB and OEB. The nap, sleep and output enable modes of the two channels are completely independent, so it is possible to have one channel operating while the other channel is in nap or sleep mode. Digital Output Multiplexer The digital outputs of the LTC2285 can be multiplexed onto a single data bus if the sample rate is 80Msps or less. The MUX pin is a digital input that swaps the two data busses. If MUX is High, channel A comes out on DA0-DA13; channel B comes out on DB0-DB13. If MUX is Low, the output busses are swapped and channel A comes out on DB0-DB13; channel B comes out on DA0-DA13. To multiplex both channels onto a single output bus, connect MUX, CLKA and CLKB together (see the Timing Diagram for the multiplexed mode). The multiplexed data is available on either data bus--the unused data bus can be disabled with its OE pin. Grounding and Bypassing The LTC2285 requires a printed circuit board with a clean, unbroken ground plane. A multilayer board with an internal ground plane is recommended. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care 2285fb 18 LTC2285 APPLICATIONS INFORMATION should be taken not to run any digital track alongside an analog signal track or underneath the ADC. High quality ceramic bypass capacitors should be used at the VDD, OVDD, VCM, REFH, and REFL pins. Bypass capacitors must be located as close to the pins as possible. Of particular importance is the 0.1F capacitor between REFH and REFL. This capacitor should be placed as close to the device as possible (1.5mm or less). A size 0402 ceramic capacitor is recommended. The large 2.2F capacitor between REFH and REFL can be somewhat further away. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. The LTC2285 differential inputs should run parallel and close to each other. The input traces should be as short as possible to minimize capacitance and to minimize noise pickup. Heat Transfer Most of the heat generated by the LTC2285 is transferred from the die through the bottom-side Exposed Pad and package leads onto the printed circuit board. For good electrical and thermal performance, the Exposed Pad should be soldered to a large grounded pad on the PC board. It is critical that all ground pins are connected to a ground plane of sufficient area. Clock Sources for Undersampling Undersampling is especially demanding on the clock source, and the higher the input frequency, the greater the sensitivity to clock jitter or phase noise. A clock source that degrades SNR of a full-scale signal by 1dB at 70MHz will degrade SNR by 3dB at 140MHz, and 4.5dB at 190MHz. In cases where absolute clock frequency accuracy is relatively unimportant and only a single ADC is required, a 3V canned oscillator from vendors such as Saronix or Vectron can be placed close to the ADC and simply connected directly to the ADC. If there is any distance to the ADC, some source termination to reduce ringing that may occur even over a fraction of an inch is advisable. You must not allow the clock to overshoot the supplies or performance will suffer. Do not filter the clock signal with a narrow band filter unless you have a sinusoidal clock source, as the rise and fall time artifacts present in typical digital clock signals will be translated into phase noise. The lowest phase noise oscillators have single-ended sinusoidal outputs, and for these devices the use of a filter close to the ADC may be beneficial. This filter should be close to the ADC to both reduce roundtrip reflection times, as well as reduce the susceptibility of the traces between the filter and the ADC. If the circuit is sensitive to closein phase noise, the power supply for oscillators and any buffers must be very stable, or propagation delay variation with supply will translate into phase noise. Even though these clock sources may be regarded as digital devices, do not operate them on a digital supply. If your clock is also used to drive digital devices such as an FPGA, you should locate the oscillator, and any clock fan-out devices close to the ADC, and give the routing to the ADC precedence. The clock signals to the FPGA should have series termination at the driver to prevent high frequency noise from the FPGA disturbing the substrate of the clock fan-out device. If you use an FPGA as a programmable divider, you must re-time the signal using the original oscillator, and the re-timing flip-flop as well as the oscillator should be close to the ADC, and powered with a very quiet supply. For cases where there are multiple ADCs, or where the clock source originates some distance away, differential clock distribution is advisable. This is advisable both from the perspective of EMI, but also to avoid receiving noise from digital sources both radiated, as well as propagated in the waveguides that exist between the layers of multilayer PCBs. The differential pairs must be close together and distanced from other signals. The differential pair should be guarded on both sides with copper distanced at least 3x the distance between the traces, and grounded with vias no more than 1/4 inch apart. 2285fb 19 ASSEMBLY TYPE DC1098A-A DC1098A-B DC1098A-C DC1098A-D DC1098A-E DC1098A-F 5 4 C15 0.1F VCMA C7 0.1F C3 0.1F BITS 10 12 14 10 12 14 + 4 5 Msps 125 125 125 125 125 125 C45 100F 6.3V OPT J4 R17 ANALOG OPT INPUT B R15 3 1k U3 NC7SVU04 2 R10 1k U1 LTC2281IUP LTC2283IUP LTC2285IUP LTC2281IUP LTC2283IUP LTC2285IUP R14 49.9 C19 0.1F C12 4.7F 6.3V VDD VCM 4 2 2 1 *3 5 4 2 1 *3 E5 PWR GND E3 VDD 3V R23 51 T2 * VDD R5, R9, R18, R24 24.9 24.9 24.9 12.4 12.4 12.4 * R9 * R7 24.9 C17 0.1F R32 OPT C6 * C52 0.1F C40 0.1F E2 EXT REF B VCMB VDD OVDD C53 0.1F QDVDD C41 0.1F VDD VCM VDD 4 2 C54 0.1F U1 LTC2285 E4 GND C35 0.1F C28 2.2F DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CLKOUT DB13 DB12 DB11 DB10 DB9 DB8 DB7 U13 VDD LT1761ES5-BYP 1 5 OUT IN 3 C51 BYP 1F 4 ADJ GND 2 C25 0.1F 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 C5 0.1F C49 0.01F OVDD C37 10F 6.3V R41 100k R40 105k C50 10F 6.3V QDVDD R25 105k R25 105k OVDD C38 0.01F OVDD U12 VDD LT1761ES5-BYP 1 5 OUT IN 3 C39 BYP 1F 4 ADJ GND 2 INPUT FREQUENCY 1MHz < AIN < 70MHz 1MHz < AIN < 70MHz 1MHz < AIN < 70MHz 70MHz < AIN < 140MHz 70MHz < AIN < 140MHz 70MHz < AIN < 140MHz C55 0.1F C48 0.1F EXT REF 5 6 3 1 C2 2.2F C27 0.1F JP3 SENSEB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AINA+ AINA- REFHA REFHA REFLA REFLA VDD CLKA CLKB VDD REFLB REFLB REFHB REFHB AINB- AINB+ C1 0.1F VDD C47 0.1F C21 0.1F C11 0.1F C4 0.1F VCMB 8 6 4 T1, T2 MABAES0060 MABAES0060 MABAES0060 MABA-007159-000000 MABA-007159-000000 MABA-007159-000000 C31 * C23 1F C6, C31 12pF 12pF 12pF 8pF 8pF 8pF C34 0.1F R24 * GND 1/3VDD 2/3VDD C20 2.2F C18 1F R22 24.9 7 5 3 C10 2.2F C9 1F R3 1k R2 1k C13 1F R20 24.9 R18 * R39 1k VDD C44 0.1F R6 24.9 R5 * C8 0.1F VDD C14 0.1F C36 4.7F VCMB C33 0.1F C29 0.1F R8 51 VDD * T1 * EXT REF 5 6 3 1 R1 1k 2 22 10 9 7 8 6 5 3 4 22 10 9 7 8 5 6 4 3 22 10 9 7 8 6 5 3 4 22 10 9 7 8 6 5 3 4 12 QDVDD 13 25 11 12 13 25 GND GND GND GND 4 U4 NC7SV86P5X U11 1 24 23 FXLH42245MPX VCCA VCCB VCCB 21 B0 A0 20 B1 A1 19 A2 B2 18 B3 A3 EXPOSED 17 A4 B4 PAD 16 B5 A5 15 B6 A6 14 B7 A7 2 T/R OE OVDD 11 QDVDD 13 25 U10 1 24 23 FXLH42245MPX VCCA VCCB VCCB 21 B0 A0 20 B1 A1 19 A2 B2 18 B3 A3 EXPOSED 17 A4 B4 PAD 16 B5 A5 15 B6 A6 14 B7 A7 2 T/R OE GND GND GND GND 12 OVDD 11 QDVDD 13 25 U9 1 24 23 FXLH42245MPX VCCA VCCB VCCB 21 B0 A0 20 B1 A1 19 A2 B2 18 B3 A3 EXPOSED 17 A4 B4 PAD 16 B5 A5 15 B6 A6 14 B7 A7 2 T/R OE GND GND GND GND 12 OVDD 11 QDVDD OVDD U2 1 24 23 FXLH42245MPX R42 VCCA VCCB VCCB 1k 21 B0 A0 20 B1 A1 19 A2 B2 18 B3 A3 EXPOSED 17 A4 B4 PAD 16 B5 A5 15 B6 A6 14 B7 A7 2 T/R OE GND GND GND GND OVDD 3 5 1 2 QDVDD C24 0.1F R35 100k U5 24LC025 25 27 29 31 30 32 53 54 61 1 A0 2 A1 3 A2 4 A3 C46 0.1F R34 4.7k 100 98 94 96 92 84 86 88 90 76 78 80 82 72 74 68 70 8 VCC 7 WP 6 SCL 5 SDA R36 4.99k 99 97 93 95 91 83 85 87 89 75 77 79 81 71 73 67 69 63 65 59 62 64 66 60 55 57 45 47 49 51 46 48 50 52 56 58 37 39 41 43 38 40 42 44 33 35 23 34 36 21 26 28 17 19 18 20 24 15 16 22 7 9 11 13 1 3 5 J1 EDGE-CON-100 8 10 12 14 2 4 6 ENABLE SDA VCCIN SCL VSS R38 4.99k R37 4.99k R33 QDVDD 4.7k 2285 AI01 SDA SCL VSS VCCIN APPLICATIONS INFORMATION *VERSION TABLE J3 CLOCK INPUT VDD L1 BEAD J2 ANALOG R4 INPUT A OPT VCMA E1 EXT REF A VDD JP2 SENSEA VDD JP1 MODE 1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 GND VDD SENSEA VCMA MODE SHDNA OEA OF DA13 DA12 DA11 DA10 DA9 DA8 OGND OVDD GND VDD SENSEB VCMB MUX SHDNB OEB DB0 DB1 DB2 DB3 DB4 DB5 DB6 OGND OVDD 20 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 VDD Evaluation Circuit Schematic of the LTC2285 LTC2285 2285fb LTC2285 APPLICATIONS INFORMATION Silkscreen Top Top Side 2285fb 21 LTC2285 APPLICATIONS INFORMATION Inner Layer 2 GND Inner Layer 3 Power Bottom Side 2285fb 22 LTC2285 PACKAGE DESCRIPTION UP Package 64-Lead Plastic QFN (9mm x 9mm) (Reference LTC DWG # 05-08-1705) 0.70 0.05 7.15 0.05 7.50 REF 8.10 0.05 9.50 0.05 (4 SIDES) 7.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 9 .00 0.10 (4 SIDES) 0.75 0.05 R = 0.10 TYP R = 0.115 TYP 63 64 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 5) 1 2 PIN 1 CHAMFER C = 0.35 7.15 0.10 7.50 REF (4-SIDES) 7.15 0.10 (UP64) QFN 0406 REV C 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION WNJR-5 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 4. EXPOSED PAD SHALL BE SOLDER PLATED 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 6. DRAWING NOT TO SCALE 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD 2285fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 23 LTC2285 TYPICAL APPLICATION PART NUMBER DESCRIPTION COMMENTS LTC1748 14-Bit, 80Msps, 5V ADC 76.3dB SNR, 90dB SFDR, 48-Pin TSSOP Package LTC1750 14-Bit, 80Msps, 5V Wideband ADC Up to 500MHz IF Undersampling, 90dB SFDR LTC1993-2 High Speed Differential Op Amp 800MHz BW, 70dBc Distortion at 70MHz, 6dB Gain LTC1994 Low Noise, Low Distortion Fully Differential Input/Output Amplifier/Driver Low Distortion: -94dB at 1MHz LTC2208 16-Bit, 130Msps, 3.3V ADC, LVDS Outputs 1250mW, 77.1dB SNR, 100dB SFDR, 64-Pin QFN Package LTC2220 12-Bit, 170Msps, 3.3V ADC, LVDS Outputs 890mW, 67.7dB SNR, 84dB SFDR, 64-Pin QFN Package LTC2224 12-Bit, 135Msps, 3.3V ADC, High IF Sampling 630mW, 67.6dB SNR, 84dB SFDR, 48-Pin QFN Package LTC2242-12 12-Bit, 250Msps, 2.5V ADC, LVDS Outputs 740mW, 65.4dB SNR, 84dB SFDR, 64-Pin QFN Package LTC2254 14-Bit, 105Msps, 3V ADC, Lowest Power 320mW, 72.4dB SNR, 88dB SFDR, 32-Pin QFN Package LTC2255 14-Bit, 125Msps ADC, 3V ADC, Lowest Power 395mW, 72.5dB SNR, 88dB SFDR, 32-Pin QFN Package LTC2280 10-Bit, Dual, 105Msps, 3V ADC, Low Crosstalk 320mW, 61.6dB SNR, 85dB SFDR, 64-Pin QFN Package LTC2282 12-Bit, Dual, 105Msps, 3V ADC, Low Crosstalk 540mW, 70.1dB SNR, 88dB SFDR, 64-Pin QFN Package LTC2284 14-Bit, Dual, 105Msps, 3V ADC, Low Crosstalk 540mW, 72.4dB SNR, 88dB SFDR, 64-Pin QFN Package LTC2286 10-Bit, Dual, 25Msps, 3V ADC, Low Crosstalk 150mW, 61.8dB SNR, 85dB SFDR, 64-Pin QFN Package LTC2287 10-Bit, Dual, 40Msps, 3V ADC, Low Crosstalk 235mW, 61.8dB SNR, 85dB SFDR, 64-Pin QFN Package LTC2288 10-Bit, Dual, 65Msps, 3V ADC, Low Crosstalk 400mW, 61.8dB SNR, 85dB SFDR, 64-Pin QFN Package LTC2289 10-Bit, Dual, 80Msps, 3V ADC, Low Crosstalk 422mW, 61.6dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2290 12-Bit, Dual, 10Msps, 3V ADC, Low Crosstalk 120mW, 71.3dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2291 12-Bit, Dual, 25Msps, 3V ADC, Low Crosstalk 150mW, 71.4dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2292 12-Bit, Dual, 40Msps, 3V ADC, Low Crosstalk 235mW, 71.4dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2293 12-Bit, Dual, 65Msps, 3V ADC, Low Crosstalk 400mW, 71.3dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2294 12-Bit, Dual, 80Msps, 3V ADC, Low Crosstalk 422mW, 70.6dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2295 14-Bit, Dual, 10Msps, 3V ADC, Low Crosstalk 120mW, 74.4dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2296 14-Bit, Dual, 25Msps, 3V ADC, Low Crosstalk 150mW, 74.5dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2297 14-Bit, Dual, 40Msps, 3V ADC, Low Crosstalk 235mW, 74.4dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2298 14-Bit, Dual, 65Msps, 3V ADC, Low Crosstalk 400mW, 74.3dB SNR, 90dB SFDR, 64-Pin QFN Package LTC2299 14-Bit, Dual, 80Msps, 3V ADC, Low Crosstalk 444mW, 73dB SNR, 90dB SFDR, 64-Pin QFN Package LT5512 DC-3GHz High Signal Level Downconverting Mixer DC to 3GHz, 21dBm IIP3, Integrated LO Buffer LT5514 Ultralow Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain 450MHz to 1dB BW, 47dB OIP3, Digital Gain Control 10.5dB to 33dB in 1.5dB/Step LT5515 1.5GHz to 2.5GHz Direct Conversion Quadrature Demodulator High IIP3: 20dBm at 1.9GHz, Integrated LO Quadrature Generator LT5516 800MHz to 1.5GHz Direct Conversion Quadrature Demodulator High IIP3: 21.5dBm at 900MHz, Integrated LO Quadrature Generator LT5517 40MHz to 900MHz Direct Conversion Quadrature Demodulator High IIP3: 21dBm at 800MHz, Integrated LO Quadrature Generator LT5522 600MHz to 2.7GHz High Linearity Downconverting Mixer 4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB, 50 Single Ended RF and LO Ports 2285fb 24 Linear Technology Corporation LT 1207 REV B * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2006