TS8GCF133 - Transcend - Datasheet.Live

133X CompactFlash Card

Transcend Information Inc.

Description

The Transcend CF 133X is a High Speed Compact

Flash Card with high quality Flash Memory assembled

on a printed circuit board.

Placement

Features

• CompactFlash Specification Version 4.1 Complaint

• RoHS compliant products

• Single Power Supply: 3.3V±5% or 5V±10%

• Operating Temperature: -25oC to 85oC

• Storage Temperature: -40oC to 85oC

• Operating Humidity (Non condensation): 0% to 95%

• Storage Humidity (Non condensation): 0% to 95%

• Operation Modes:

9 PC Card Memory Mode

9 PC Card IO Mode

9 True IDE Mode

• True IDE Mode supports:

9 Ultra DMA Mode 0 to Mode 4

9 MultiWord DMA Mode 0 to Mode 4

9 PIO mode 0 to mode 6

• True IDE mode: Removable Disk (Standard)

• PC Card Mode: Removable Disk (Standard)

• Durability of Connector: 10,000 times

• Support S.M.A.R.T (Self-defined)

• Support Security Command

• Support Wear-Leveling to extend product life

• Compliant to CompactFlash, PCMCIA, and ATA

standards

Dimensions

133X CompactFlash Card

Transcend Information Inc.

Transcend

133X CompactFlash Card

Transcend Information Inc.

Block Diagram

133X CompactFlash Card

Transcend Information Inc.

Pin Assignments and Pin Type

133X CompactFlash Card

Transcend Information Inc.

Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit

system s. Devices should allow for 3-state signals not to consume current.

2) The signal should be grounded by the host.

3) The signal should be tied to VCC by the host.

4) The mode is required for CompactFlash Storage Cards.

5) The -CSEL signal is ignored by the card in PC Card modes. However, because it is not

pulled upon t he card in these modes, it should not be left floating by the host in PC Card

modes. In these modes, the pin should be connected by the host to PC Card A25 or

grounded by the host.

6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. For

proper operation in older hosts: while DMA operations are not active, the card shall ignore

this signal,including a floating condition

7) Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.

8) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.

9) Signal usag e in True IDE Mode when Ul tra DMA mode protocol DMA Read is active.

10) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.

11) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.

12) Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.

133X CompactFlash Card

Transcend Information Inc.

Signal Description

Signal Name Dir. Pin Description

A10 – A00

(PC Card Memory Mode)

A10 – A00

(PC Card I/O Mode)

A02 - A00

(True IDE Mode)

8,10,11,12,

14,15,16,17,

18,19,20

These address lines alo ng with the -REG signal are used to select the following:

The I/O port address registers within the CompactFlash Storage Card , the

memory mapped port address registers within the CompactFlash Storage Card,

a byte in the card's information structure and its configuration control and status

registers.

This signal is the same as the PC Card Memory Mode signal.

In True IDE Mode, only A[02:00] are used to select the one of eight registers

in the Task File, the remaining address lines should b e grounded by the host.

BVD1

(PC Card Memory Mode)

-STSCHG

(PC Card I/O Mode)

Status Changed

-PDIAG

(True IDE Mode)

I/O 46 This signal is asserted high, as BVD1 is not supported.

This signal is asserted low to alert the host to changes in the READY and Write

Protect states, while the I/O interface is configured. Its use is controlled by the

Card Config and Status Register.

In the True IDE Mode, this input / output is the Pass Diagnostic signal in the

Master / Slave handshake protocol.

BVD2

(PC Card Memory Mode)

-SPKR

(PC Card I/O Mode)

-DASP

(True IDE Mode)

I/O 45 This signal is asserted high, as BVD2 is not supported.

This line is the Binary Audio output from the card. If the Card does not support

the Binary Audio function, this line should be held negated.

In the True IDE Mode, this input/output is th e Disk Active/Slave Present signal in

the Master/Slave handshake protocol.

-CD1, -CD2

(PC Card Memory Mode)

-CD1, -CD2

(PC Card I/O Mode)

-CD1, -CD2

(True IDE Mode)

O 26,25 These Card Detect pins are connected to ground on the CompactFlash Storage

Card. They are used by the host to determine that the CompactFlash Storage

Card is fully inserted into its socket.

This signal is the same for all modes.

133X CompactFlash Card

Transcend Information Inc.

Signal Name Dir. Pin Description

-CE1, -CE2

(PC Card Memory Mode)

Card Enable

-CE1, -CE2

(PC Card I/O Mode)

Card Enable

-CS0, -CS1

(True IDE Mode)

I 7,32 These input signals are used both to select the card and to indicate to the card

whether a byte or a word operation is being performed. -CE2 always accesses

the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the

word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1,

-CE2 allows 8 bit hosts to access all data on D0-D7. See Table 27, Table 29,

Table 31, Table 35, Table 36 and Table 37.

This signal is the same as the PC Card Memory Mode signal.

In the True IDE Mode, -CS0 is the address range select for the task file

registers while -CS1 is used to select the Alternate Status Register and the

Device Control Register.

While –DMACK is asserted, -CS0 and –CS1 shall be held negated and the

width of the transfers shall be 16 bits.

-CSEL

(PC Card Memory Mode)

-CSEL

(PC Card I/O Mode)

-CSEL

(True IDE Mode)

I 39 This signal is not used for this mode , but shou ld be conne cted by the host to PC

Card A25 or grounded by the host.

This signal is not used for this mode, but shou ld be connected by the host to PC

Card A25 or grounded by the host.

This internally pulled up signal is used to configure this device as a Master or a

Slave when configured in the True IDE Mode.

When this pin is grounded, this device is configured as a Master.

When the pin is open, this device is configured as a Slave.

D15 - D00

(PC Card Memory Mode)

D15 - D00

(PC Card I/O Mode)

D15 - D00

(True IDE Mode)

I/O 31,30,29,28,

27,49,48,47,

6,5,4,3,2,

23, 22, 21

These lines carry th e Data, Commands and Status information between the host

and the controller. D00 is the LSB of the Even Byte of the Word. D08 is th e LSB

of the Odd Byte of the Word.

This signal is the same as the PC Card Memory Mode signal.

In True IDE Mode, all Task File operations occur in byte mode on the low order

bus D[7:0] while all data transfers are 16 bit using D[15:0].

GND

(PC Card Memory Mode)

GND

(PC Card I/O Mode)

GND

(True IDE Mode)

-- 1,50 Ground.

This signal is the same for all modes.

133X CompactFlash Card

Transcend Information Inc.

Signal Name Dir. Pin Description

-INPACK

(PC Card Memory Mode)

-INPACK

(PC Card I/O Mode)

Input Acknowledge

DMARQ

(True IDE Mode)

O 43 This signal is not used in this mode.

The Input Acknowledge signal is asserted by the CompactFlash Storage Card

when the card is selected and respondin g to an I/O read cycle at the address th at

is on the address bus. This signal is u sed by the host to control the enable of any

input data buffers between the CompactFlash Storage Card and the CPU.

This signal is a DMA Request that is used for DMA data transfers between host

and device. It shall be asse rted by the device when it is ready to transfer data to

or from the host. For Multiword DMA transfers, the direction of data transfer is

controlled by -IORD and -IOWR. This signal is used in a hand shake manner with

-DMACK, i.e., the device shall wait until the host asserts -DMACK before

negating DMARQ, and reasserting DMARQ if there is more data to transfer.

DMARQ shall not be driven when the device is not selected.

While a DMA operation is in progress, -CS0 and –C S1 shall be held negated and

the width of the transfers shall be 16 bits.

If there is no h ardware support for DMA mode in the host, this outpu t signal is not

used and should no t be connected at the host. In this case , the BIOS must report

that DMA mode is not supported by the host so that device drivers will not

attempt DMA mode.

A host that does not support DMA mode and implements both PCMCIA and

True-IDE modes of operation need not alter the PCMCIA mode connections

while in True-IDE mode as long a s this does n ot prevent proper operation in any

mode.

-IORD

(PC Card Memory Mode)

-IORD

(PC Card I/O Mode)

-IORD

(True IDE Mode – Except

Ultra DMA Protocol Active)

-HDMARDY

(True IDE Mode – In Ultra

DMA Protocol DMA Read)

HSTROBE

(True IDE Mode – In Ultra

DMA Protocol DMA Write)

I 34 This signal is not used in this mode.

This is an I/O Read strobe generate d by the host. This signal g ates I/O data onto

the bus from the CompactFla sh Storage Card when th e card is configured to use

the I/O interface.

In True IDE Mode, while Ultra DMA mode is not active, this signal has the same

function as in PC Card I/O Mode.

In True IDE Mode when Ultra DMA mode DMA Read is active, this signal is

asserted by the host to indicate that th e host is read to receive Ultra DMA data-in

bursts. The host may negate -HDMARDY to pause an Ultra DMA transfer.

In True IDE Mode when Ultra DMA mode DMA Write is active, this signal is the

data out strobe generated by the host. Both the rising and falling edge of

HSTROBE cause data to be latched by the device. The host may stop

generating HSTROBE edges to pause an Ultra DMA data-out burst.

133X CompactFlash Card

Transcend Information Inc.

Signal Name Dir. Pin Description

-IOWR

(PC Card Memory Mode)

-IOWR

(PC Card I/O Mode)

-IOWR

(True IDE Mode – Except

Ultra DMA Protocol Active)

STOP

(True IDE Mode – Ultra DMA

Protocol Active)

I 35 This signal is not used in this mode.

The I/O Write strobe pulse is used to clock I/O data on the Card Data bus into th e

CompactFlash Storage Card controller registers when the CompactFlash

Storage Card is configured to use the I/O interface.

The clocking shall occur on the negative to positive edge of t he signal ( tr a iling

edge).

In True IDE Mode, while Ultra DMA mode protocol is not active, this signal has

the same function as in PC Card I/O Mode. When Ultra DMA mode protocol is

supported, this signal must be negated before entering Ultra DMA mode

protocol.

In True IDE Mode, while Ultra DMA mode protocol is active, the a ssertio n of this

signal causes the termination of the Ultra DMA burst.

-OE

(PC Card Memory Mode)

-OE

(PC Card I/O Mode)

-ATA SEL

(True IDE Mode)

I 9 This is an Output Enable strobe generated by the host interface. It is used to read

data from the CompactFlash Stora ge Card in Memory Mode and to read the CIS

and configuration registers.

In PC Card I/O Mode, this signal is used to read the CIS and configuration

registers.

To enable True IDE Mode this input should be grounded by the host.

READY

(PC Card Memory Mode)

-IREQ

(PC Card I/O Mode)

INTRQ

(True IDE Mode)

O 37 In Memory Mode, this signal is set hig h when the CompactFlash Storage Card is

ready to accept a new data transfer operation and is held low when the card is

busy.

At power up and at Reset, the READY signal is held low (busy) until the

CompactFlash Storage Card has completed its power up or reset function. No

access of any type should be made to the CompactFlash Storage Card during

this time.

Note, however, that when a card is powered up and used with RESET

continuously disconnected or asserted, the Reset function of the RESET pin is

disabled. Conse quently, the contin uous assertion of RESET from the application

of power shall not cause the READY signal to remain continuously in the busy

state.

I/O Operation – After the CompactFlash Storage Card Card ha s been configured

for I/O operation, this signal is used as -Interrupt Request. This line is strobed

low to generate a pulse mode interrupt or held low for a level mode interrupt.

In True IDE Mode signal is the active high Interrupt Request to the host.

133X CompactFlash Card

Transcend Information Inc.

Signal Name Dir. Pin Description

-REG

(PC Card Memory Mode)

Attribute Memory Select

-REG

(PC Card I/O Mode)

I 44 This signal is used during Memory Cycles to distinguish between Common

Memory and Register (Attribute) Memory accesses. High for Common Memory,

Low for Attribute Memory.

The signal shall also be active (low) du ring I/O Cycles when the I/O address is on

the Bus.

-DMACK

(True IDE Mode) This is a DMA Acknowledge signal that is asserted by the host in response to

DMARQ to initiate DMA transfers.

While DMA operations are not active, the card shall ignore the -DMACK signal,

including a floating condition.

If DMA operation is not supported by a True IDE Mode only host, this signal

should be driven high or connected to VCC by the host.

A host that does not support DMA mode and implements both PCMCIA and

True-IDE modes of operation need not alter the PCMCIA mode connections

while in True-IDE mode as long as this does not prevent proper operation all

modes.

RESET

(PC Card Memory Mode)

RESET

(PC Card I/O Mode)

-RESET

(True IDE Mode)

I 41 The CompactFlash Storage Card is Reset when the RESET pin is high with the

following important exception:

The host may leave the RESET pin open or keep it continually high from the

application of power without causing a continuous Reset of the card. Under

either of these conditions, the card shall emerge from power-up having

completed an initial Reset.

The CompactFlash Storage Card is also Reset when the Soft Reset bit in the

Card Configuration Option Register is set.

This signal is the same as the PC Card Memory Mode signal.

In the True IDE Mode, this input pin is the active low hardware reset from the

host.

VCC

(PC Card Memory Mode)

VCC

(PC Card I/O Mode)

VCC

(True IDE Mode)

-- 13,38 +5 V, +3.3 V power.

This signal is the same for all mo des.

This signal is the same for all modes.

133X CompactFlash Card

Transcend Information Inc.

Signal Name Dir. Pin Description

-VS1

-VS2

(PC Card Memory Mode)

-VS1

-VS2

(PC Card I/O Mode)

-VS1

-VS2

(True IDE Mode)

O 33

40 Voltage Sense Signals. -VS1 is grounded on the Card and sensed by the Host so

that the CompactFlash Storage Card CIS can be read at 3.3 volts and -VS2 is

reserved by PCMCIA for a sec onda ry voltage and is not conne cted o n th e Card.

This signal is the same for all modes.

-WAIT

(PC Card Memory Mode)

-WAIT

(PC Card I/O Mode)

IORDY

(True IDE Mode – Except

Ultra DMA Mode)

-DDMARDY

(True IDE Mode – Ultra DMA

Write Mode)

DSTROBE

(True IDE Mode – Ultra

DMA Read Mode)

O 42 The -WAIT signal is driven low by the CompactFlash Storage Card to signal th e

host to delay completion of a memory or I/O cycle that is in progress.

This signal is the same as the PC Card Memory Mode signal.

In True IDE Mode, except in Ultra DMA modes, this outp ut signal may be used as

IORDY.

In True IDE Mode, when Ultra DMA mode DMA Write is active, this signal is

asserted by the host to indicate that the device is read to receive Ultra DMA

data-in bursts. The device may negate -DDMARDY to pause an Ultra DMA

transfer.

In True IDE Mode, when Ultra DMA mode DMA Write is active, this signal is the

data out strobe generated by the device. Both the rising and falling edge of

DSTROBE cause data to be latched by the host. The device may stop

generating DSTROBE edges to pause an Ultra DMA data-out burst.

-WE

(PC Card Memory Mode)

-WE

(PC Card I/O Mode)

-WE

(True IDE Mode)

I 36 This is a signal driven by the h ost and used for strobing memory write data to the

registers of the CompactFlash Storage Card when the card is configured in the

memory interface mode. It is also used for writing the configuration registers.

In PC Card I/O Mode, this signal is used for writing the configuration registers.

In True IDE Mode, this input signal is not used an d should be connected to VCC

by the host.

(PC Card Memory Mode)

Write Protect

-IOIS16

(PC Card I/O Mode)

-IOCS16

(True IDE Mode)

O 24 Memory Mode – The CompactFlash Storage Card does not have a write protect

switch. This signal is held low after the completion of the reset initialization

sequence.

I/O Operation – When the CompactFlash Storage Card is configured for I/O

Operation Pin 24 is used for the -I/O Selected is 16 Bit Port (-IOIS16) function. A

Low signal indicates that a 16 bit or odd byte only opera tion can be performed at

the addressed port.

In True IDE Mode this outp ut signal is asserted low when this device is ex pecting

a word data transfer cycle.

133X CompactFlash Card

Transcend Information Inc.

Electrical Specification

The following tables indicate all D.C. Characteristics for the CompactFlash Storage Card. Unless

otherwise stated, conditions are:

Vcc = 5V ±10%

Vcc = 3.3V ± 5%

 Absolute Maximum Conditions

 Input Power

 Input Leakage Current

 Input Characteristics

133X CompactFlash Card

Transcend Information Inc.

 Output Drive Type

 Output Drive Characteristics



133X CompactFlash Card

Transcend Information Inc.

 Signal Interface

133X CompactFlash Card

Transcend Information Inc.

Notes: 1) Control Signa ls: each card shall present a load to the so cket no larger than 50 pF 10 at a DC current of 700 μA low

state and 150 μA high state, includ ing pull-resistor. The socket shall be able to drive at least the following load

10 while meeting all AC timing requirements: (the number of sockets wired in parallel) multiplied by (50 pF with

DC current 700 μA low state and 150 μA high state per socket).

2) Resistor is optional.

3) Status Signals: the socket shall present a loa d to the card no larger than 50 pF 10 at a DC current of 400 μA low

state and 100 μA high state, in cluding pull-up re sistor. The card shall be ab le to drive a t least the following load

10 while meeting all AC timing re quire ments: 5 0 pF at a DC current of 4 00 μA low state a nd 100 μA h i gh state.

4) Status Signals: the socket shall present a loa d to the card no larger than 50 pF 10 at a DC current of 400 μA low

state and 100 μA high state, in cluding pull-up re sistor. The card shall be ab le to drive at leas t the following lo ad

10 while meeting all AC timing re quire ments: 5 0 pF at a DC current of 4 00 μA low state a nd 100 μA h i gh state.

5) Status Signals: the socket shall presen t a load to the card no larger than 50 pF 10 at a DC current of 40 0 μA low

state and 100 μA high state, in cluding pull-up re sistor. The card shall be ab le to drive at leas t the following lo ad

10 while meeting all AC timing requirements: 50 pF at a DC current o f 400 μA low state and 1100 μA high state.

6) BVD2 was not defined in the JEIDA 3.0 release. Systems fully supporting JEIDA release 3 SRAM cards shall

pull-up pin 45 (BVD2) to avoid sensing their batteries as “Low.”

7) Address Signals : each card shall present a load of no more than 100pF 10 at a DC current of 450μA low state and

150μA high state. The host shall be able to drive at least the following load 10 while meeting all AC tim ing

requirements: (the number of sockets wired in parallel) multiplied by (100pF with DC current 450 μA low st ate

and 150μA high state per socket).

8) Data Signals: the host and each card shall present a load no larger than 50pF 10 at a DC current of 450μA and

150μA high state. The host and each card sh all be able to drive at least the following load 10 while meeting all AC

timing requirements: 100 pF with DC current 1.6mA low state and 300μA hi gh state. This permits the host to wire

two sockets in parallel without derating the card access speeds.

9) Reset Signal: This signal is pulled up to pre vent the input from floating when a CFA to PCMCIA adapter is used in

a PCMCIA revision 1 host. However, to minimize DC current drain through the pull-up resistor in normal

operation the pull-up should be turned off once the Reset signal has been actively driven low by the host.

Consequently, the input is specified as an I2Z because the resistor is not necessarily detectable in the input

current leakage test.

10) Host and card restrictions for CF Advanced Timing Modes and Ultra DMA modes: Additional Requirements for

CF Advanced Timing Modes and Ultra DMA Electrical Requirements for additional required limitations on the

implementation of CF Advanced Timing modes and Ultra DMA modes respectively.

 Additi onal Requirements for CF Advanced Timing Modes

The CF Advanced Timing modes include PCMCIA I/O and Memory modes that are 100ns or faster and True

IDE PIO Modes 5,6 and Multiword DMA Modes 3,4.

When operating in CF Advanced timing modes, the host shall conform to the following requirements:

1) Only one CF device shall be attached to the CF Bus.

2) The host shall not present a load of more than 40pF to the device for all signals, including any cabling.

3) The maximum cable length is 0.1 5 m (6 in). The cable length is measured from the card co nnector to the host

controller. 0.46 m (18 in) cables are not supported.

4) The -WAIT and IORDY signals shall be ignored by the host.

Devices supporting CF Advanced timing modes shall also support slower timing modes, to ensure operability with

systems that do not support CF Advanced timing modes

133X CompactFlash Card

Transcend Information Inc.

 Ultra DMA Electrical Requirements

¾ Host and Card signal capacitance limits for Ultra DMA operation

The host interface signal capacitance a t the host connector shall b e a maximum of 25 pF for each signal as measured at

1 MHz. The card interface signal capacitance at the card connector shall be a maximum of 20 pF for each signal as

measured at 1 MHz.

¾ Series termination required for Ultra DMA operation

Series termination resistors are required at both the h ost and the card for operation in any of the Ultra DMA modes. Table

13 describes typical values for series termination at the host and the device.

Table: Typical Series Termination for Ultra DMA

133X CompactFlash Card

Transcend Information Inc.

¾ Printed Circuit Board (PCB) Trace Requirements for Ultra DMA

On any PCB for a host or device supporting Ultra DMA:

9 The longest D[15:00] trace shall be no more than 0.5" longer than either STROBE trace as measured from the

IC pin to the connector.

9 The shortest D[15:00] trace shall be no more than 0.5" shorter than either STROBE trace as measured from

the IC pin to the connector.

¾ Ultra DMA Mode Cabling Requirement

9 Operation in U ltra D M A mode re qu ires a c ross t alk s upp re ss in g ca ble . Th e cab le s hall hav e a grou nd ed line

between each signal line.

9 For True IDE mode operation using a cable with IDE (ATA) type 40 pin connectors it is recommended that the

host sense the cable type using the method described in the ANSI INCITS 361-2002 AT Attachment - 6

standard, to prevent use of Ultra DMA with a 40 conductor cable.

Table: Ultra DMA Termination with Pull-up or Pull down Example

133X CompactFlash Card

Transcend Information Inc.

 Attribute Memory Read Timing Specification

133X CompactFlash Card

Transcend Information Inc.

 Configuration Register (Attribute Memory) Write Timing Specification

133X CompactFlash Card

Transcend Information Inc.

 Common Memory Read Timing Specification

133X CompactFlash Card

Transcend Information Inc.

 Common Memory Write Timing Specification

133X CompactFlash Card

Transcend Information Inc.

 I/O Input (Read) Timing Specification

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

 I/O Output (Write) Timing Specification

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

 True IDE PIO Mode Read/Write Tim i ng Specificati on

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

 True IDE Ultra DMA Mod e Read/Wri te Timing Speci fication

Table: Ultra DMA Data Bu rst Timin

133X CompactFlash Card

Transcend Information Inc.

Notes: 1) All timing measurement switching points (low to high and high to low) shall be taken at 1.5 V.

2) All signal transitions for a timing parameter shall be measured at the connector specified in the

measurement location column. For example, in the case of tRFS, both STROBE and –DMARDY

transitions are measured a t the sender connector.

3) The parameter tCYC shall be measured at the recipient’s connector farthest from the sender.

4)The parameter tLI shall be measured at the connector of the sender or recipient that is

responding to an incoming transition from the re cipient or sende r respectively. Both the in coming

signal and the outgoing response shall be measured at the same connector.

5)The parameter tAZ shall be measured at the connector of the sender or recipient that is driving

the bus but must release the bus the allow for a bus turnaround.

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

Notes: 1) The paramete rs tUI, tMLI : (Ultra DMA Data-In Burst Device T ermination Timing and Ultra DMA

Data-In Burst Host Termination Timing), and tLI indicate sender-to-recipient or recipient-to-sender

interlocks, i.e., one agent (eithe r sender or recipient) is waiting for the other agen t to respond with a

signal before proceeding. tUI is an unlimited interlock that has no maximum time value. tMLI is a

limited time-out that has a defined minimum. tLI is a limited time-out that has a defined maximum.

2) 80-conduc tor cabling shall be required in orde r to meet setup (t DS, tCS) and hold (tDH, tCH) times

in modes greater than 2.

3) Timing for tDVS, tDVH, tCVS and tCVH shall be met for lumped capacitive loads of 15 and 40 pF

at the connector where the Data an d STROBE signa l s have the same capa citive load value. Due to

reflections on the cable, these timing measurements are not valid in a normally functioning system.

4)For all modes the pa rameter tZIORDY may b e greater than tENV due t o the fact that the host h as a

pull-up on IORDY- giving it a known state when released.

5)The parameters tDS, and tDH for mode 5 are defined for a recipient at the end of the cable only in

a configuration with a single device located at the end of the cable. This could result in the minimum

values for tDS and tDH for mode 5 at the middle connector being 3.0 and 3.9 ns respectively.

Notes: 1) All timing measurement switching points(low to high and high to low) shall be taken at 1.5 V.

2) The correct data value shall be captured by the recipient given input data with a slew rate of 0.4

V/ns rising and falling and th e input STROBE with a slew rate of 0 .4 V/ns rising and falling a t tDSIC

and tDHIC timing (as measured through 1.5 V).

3) The parameters tDVSIC and tDVHIC shall be met for lumped capacitive loads of 15 and 40 pF at

the IC where all signals have the same capacitive load value. Noise that may couple onto the output

signals from external sources has not been included in these values.

133X CompactFlash Card

Transcend Information Inc.

Note: 1) The sender shall be tested while driving an 18 inch lon g, 80 conductor cable with PVC insulation

material. The signal under te st shall be cut at a test point so that it has not trace, cab le or recipient

loading after the test point. All other signals should remain connected through to the recipient. The

test point may be located at an y point between the sender’s series termination re sistor and one half

inch or less of conductor exiting the connector. If the test point is on a cable conductor rather than the

PCB, an adjacent ground conductor shall also be cut within one half inch of the connector.

The test load and test points should then be soldered directly to the exposed source side connectors.

The test loads consist of a 15 pF or a 40 pF, 5%, 0.08 inch by 0.05 inch surface mount or smaller size

capacitor from the test point to ground. Slew rates shall be met for both capacitor values.

Measurements shall be taken at the test point using a <1 pF, >100 Kohm, 1 Ghz or faster probe and

a 500 MHz or faster oscillosc ope. The average rate shall be measured from 20% to 80% of the set tled

VOH level with data transitions at least 120 nsec apart. The settled VOH level shall be measu red as

the average output high lev el under the defi ned testing c onditions from 100 nsec after 80% of a rising

edge until 20% of the subsequent falling edge.

133X CompactFlash Card

Transcend Information Inc.

Card Configuration

The CompactFlash Storage Cards is identified by appropriate information in the Card Information Structure

(CIS). The following configuration registers are used to coordinate the I/O spaces and the Interrupt level of cards

that are located in the system. In addition, these registers provide a method for accessing status information

about the CompactFlash Storage Car d that may be used to ar bitrate be tween multiple inte rr upt sources on the

same interrup t le vel or to re pla ce status info rma tion tha t appe ars on dedicated pins in memor y cards th at ha ve

alternate use in I/O cards.

 Multiple Function CompactFlash Storage Cards

Table: CompactFlash Storage Card Configuration Registers Decoding

Table: CompactFlash Storage Card Registers and Memory Space Decoding

133X CompactFlash Card

Transcend Information Inc.

 Attribute Memory Function

Attribute memory is a space where CompactF lash Stor age Card identification a nd co nfigu r a tion infor mation

are stored, and is limited to 8 bit wide accesses only at even addresses. The card configuration registers are

also located here. Fo r CompactFlash Stor ag e Cards, the base ad dress of the ar d con figuration reg isters is

200h.

Table 31: Attribute Memory Function

133X CompactFlash Card

Transcend Information Inc.

 Configuration Option Register (Base + 00h in Attribute Memory)

133X CompactFlash Card

Transcend Information Inc.

 Card Configuration and Status Register (Base + 02h in Attribute Memory)

133X CompactFlash Card

Transcend Information Inc.

 Pin Replacement Register (Base + 04h in Attribute Memory)

133X CompactFlash Card

Transcend Information Inc.

 Socket and Copy Register (Base + 06h in Attribute Memory)

133X CompactFlash Card

Transcend Information Inc.

I/O Transfer Function

The I/O transfer to or from the CompactFlash Storage can be either 8 or 16 bits. When a 16 bit accessible

port is addressed, the signal -IOIS16 is asserted by the CompactFlash Storage. Otherwise, the -IOIS16

signal is de-asserted. When a 16 bit transfer is attempted, and the -IOIS16 signal is not asserted by the

CompactFlash Storage, the system shall generate a pair of 8 bit references to access the word‘s even byte

and odd byte. The CompactFlash Storage Card permits both 8 and 16 bit accesses to all of its I/O addresses,

so -IOIS16 is asserted for all addr esses to which the CompactFlash Storage responds. The CompactFlash

Storage Card may request the host to extend the length of an input cycle until data is ready by asserting the

-WAIT signal at the start of the cycle.

Table : PCMCIA Mode I/O Function

133X CompactFlash Card

Transcend Information Inc.

Common Memory Transfer Function

The Common Memory transfer to or from the CompactFlash St orage can be either 8 or 16 bits.

Table: Common Memory Function

133X CompactFlash Card

Transcend Information Inc.

True IDE Mode I/O Transfer Function

The CompactFlash Storage Card can be configured in a True IDE Mode of operation. The CompactFlash Storage

Card is configured in this mode only when the - OE input signal is grounded by the host during the power off to

power on cycle. Optionally, CompactFlash Storage Cards may support the following optional detection methods:

1. The card is permitted to monitor the – OE (-ATA SEL) signa l at any time(s) and switch to PCMCIA mode u pon

detecting a high level on the pin.

2. The card is permitted to re-arbitrate the interface mode determination following a transition of the (-)RESET pin.

3. The card is permitte d to mon ito r the –OE (-ATA SEL) signal at any time(s) and switch to True IDE mo de u pon

detection of a contin uo us low level on pin for an extended period of time.

Table: True IDE Mode I/O Function defines the function of the operations for the True IDE Mode.

133X CompactFlash Card

Transcend Information Inc.

Metaformat Overview

The goal of the Metaformat is to de scribe the requirements and capabilities of the CompactFlash Storage C ard as

thoroughly as p ossible. Th is includes des cribing the pow er requirements, IO require ments, memory re quirements,

manufacturer information and details about the services provided.

Table: Sample Device Info Tuple Information for Extended Speeds

Note: The value “1” defined for D3 of the N+0 words indicates that no write-protect switch controls writing the ATA

regist ers. The v alue “ 0” def ined f or D7 in t he N+2 w ords indicates that there is not more than a single speed

extension byte.

133X CompactFlash Card

Transcend Information Inc.

CF-ATA Drive Register Set Definition and Protocol

The CompactFlash Storage Card can be configured as a high performance I/O device through:

a) The standard PC -A T dis k I/O ad dress spaces 1F0h-1F7 h, 3F6h-3F7h (prima ry ) or 170h- 17 7h , 376h -377 h

(secondary) with IRQ 14 (or other available IRQ).

b) Any system decoded 16 byte I/O block using any available IRQ.

c) Memory space.

The communication to or from the CompactFlash Storage Card is done using the Task File registers, which

provide all the necessary registers for control and status information related to the storage medium. The PCMCIA

interface connects peripherals to the host using four register mapping methods. Table 39 is a detailed description

of these methods:

133X CompactFlash Card

Transcend Information Inc.

 I/O Prim ary and Secondary Address Configurations

Table: Primary and Secondary I/O Decoding

133X CompactFlash Card

Transcend Information Inc.

 Contiguous I/O Mapped Addressing

When the system decodes a contiguous block of I/O registers to select the CompactFlash Storage Card, the

registers are accessed in the block of I/O space decoded by the system as follows:

Table: Contiguous I/O Decoding

133X CompactFlash Card

Transcend Information Inc.

 Memory Mapped Addressing

When the CompactFlash Storage Card registers are accessed via memory references, the registers appear in the

common memory space window: 0-2K bytes as follows:

 True IDE Mode Addressing

When the CompactFlash Storage Card is configured in the True IDE Mode, the I/O decoding is as follows:

133X CompactFlash Card

Transcend Information Inc.

 CF-ATA Registers

The following section describes the hardware registers used by the host software to issue commands to the

CompactFlash device. These registers are often collectively referred to as the “task file.”

¾ Data Register (Address - 1F0h[170h];Offset 0,8,9)

The Data Register is a 16 bit register, and it is used to transfer data blocks between the CompactFlash

Storage Card data buffer and the Host. This register overlaps the Error Register.

Error Register (Address - 1F1h[171h]; Offset 1, 0Dh Read Only)

This register contains additional information about the source of an error when an error is indicated in bit 0

of the Status register.

This register is also accessed in PC Card Modes on data bits D15-D8 during a read operation to offset 0

with -CE2 low and -CE1 high.

Bit 7 (BBK/ICRC): this bit is set when a Bad Block is detected. This bit is also set when an interface CRC

error is detected in True IDE Ultra DMA modes of operation.

Bit 6 (UNC): this bit is set when an Uncorrectable Error is encountered.

Bit 5: this bit is 0.

Bit 4 (IDNF): the requested sector ID is in error or cannot be found.

Bit 3: this bit is 0.

Bit 2 (Abort) This bit is set if the comman d has been a borted because of a CompactFlash Storag e Card

status condition: (Not Ready, Write Fault, etc.) or when an invalid command has been issued.

Bit 1 This bit is 0.

Bit 0 (AMNF) This bit is set in case of a general error.

133X CompactFlash Card

Transcend Information Inc.

¾ Feature Register (Address - 1F1h[171h]; Offset 1, 0Dh Write Only)

This register provides information regarding features of the CompactFlash Storage Card that the host can

utilize. This register is also accessed in PC Card modes on data bits D15-D8 during a write operation to

Offset 0 with -CE2 low and -CE1 high.

¾ Sector Count Register (Address - 1F2h[172h]; Offset 2)

This register contains the numbers of sectors of data requested to be transferred on a read or write

operation between the host and the CompactFlash Storage Card. If the value in this register is zero, a count

of 256 sectors is specified. If the command was successful, this register is zero at command completion. If

not successfully completed, the register contains the number of sectors that need to be transferred in order

to complete the request.

¾ Sector Number (LBA 7-0) Register (Address - 1F3h[173h]; Offset 3)

This register contains the starting sector number or bits 7-0 of the Logical Block Address (LBA) for any

CompactFlash Storage Card data access for the subsequent command.

¾ 6.1.5.5 Cylinder Low (LBA 15-8) Register (Address - 1F4h[174h]; Offset 4)

This register contains the low order 8 bits of the starting cylinder address or bits 15-8 of th e Logical Block

Address.

¾ Cylinder High (LBA 23-16) Register (Address - 1F5h[175h]; Offset 5)

This register contains the high order bits of the starting cylinder add ress or bits 23-16 of th e Logical Block

Address.

¾ Drive/Head (LBA 27-24) Register (Address 1F6h[176h]; Offset 6)

The Drive/Head register is used to select the drive and head. It is also used to select LBA addressing

instead of cylinder/head/sector addressing.

Bit 7: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become

obsolete in a future revision of the specification. This bit is ignored by some controllers in some

commands.

Bit 6: LBA is a flag to select either Cylinder/Head/Sector (CHS) or Logical Block Address Mode (LBA).

When LBA=0, Cylinder/Head/Sector mode is selected. When LBA=1, Logical Block Address is

selected. In Logical Block Mode, the Logical Block Address is interpreted as follows:

LBA7-LBA0: Sector Number Register D7-D0.

LBA15-LBA8: Cylinder Low Register D7-D0.

LBA23-LBA16: Cylinder High Register D7-D0.

LBA27-LBA24: Drive/Head Register bits HS3-HS0.

Bit 5: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become

obsolete in a future revisions of the specification. This bit is ignored by some controllers in some

commands.

Bit 4 (DRV): DRV is the drive number. When DRV=0, drive (card) 0 is selected. When DRV=1, drive (card)

1 is selected. Setting this bit to 1 is obsolete in PCMCIA modes of operation. If the obsolete

functionality is support by a C F Storage Card , the CompactF lash Storage C ard is set to be Card 0 or 1

using the copy field (Drive #) of the PCMCIA Socket & Copy configuration register.

133X CompactFlash Card

Transcend Information Inc.

Bit 3 (HS3): when operating in th e Cylinde r, Head , Sector mode, this is b it 3 o f the h ea d nu mber. It is Bit

27 in the Logical Block Address mode.

Bit 2 (HS2): when operating in th e Cylinde r, Head, Sector mode, this is bit 2 o f the h ead number. It is Bit

26 in the Logical Block Address mode.

Bit 1 (HS1): when operating in th e Cylinde r, Head, Sector mode, this is bit 1 o f the h ead number. It is Bit

25 in the Logical Block Address mode.

Bit 0 (HS0): when operating in th e Cylinde r, Head, Sector mode, this is bit 0 o f the h ead number. It is Bit

24 in the Logical Block Address mode.

¾ Status & Alternate Status Registers (Address 1F7h[177h]& 3F6h[376h]; Offsets 7 & Eh)

These registers return the CompactFlash Storage Card status when read by the host. Reading

the Status register does clear a pending interrupt w hile reading the Auxiliary Status register does

not. The status bits are described as follows:

Bit 7 (BUSY): the busy bit is s et when the CompactFlash Storage Card has access to the command buffer

and registers and the host is locked out from accessing the command register and buffer. No other bits

in this register are valid when this bit is set to a 1. During the data transfer of DMA commands, the Card

shall not assert DMARQ unless either the BUSY bit, the DRQ bit, or both are set to one.

Bit 6 (RDY): RDY indicates whether the device is capable of performing CompactFlash Storage Card

operations. This bit is cleared at power up and remains cleared until th e Comp actFlash Stor ag e Card

is ready to accept a command.

Bit 5 (DWF): This bit, if set, indicates a write fault has occurred.

Bit 4 (DSC): This bit is set when the CompactF lash Storag e Card is ready.

Bit 3 (DRQ): The Data Request is set when the CompactFlash Storage Card requires that information be

transferred either to or from the host through the Data register. During the data transfer of DMA

commands, the Card shall not assert DMARQ unless either the BUSY bit, the DRQ bit, or both are set

to one.

Bit 2 (CORR): This bit is set when a Correctable data error has been encountered and the data has been

corrected. This condition does not terminate a multi-sector read operation.

Bit 1 (IDX): This bit is always set to 0.

Bit 0 (ERR): This bit is set when the previou s command has ende d in some type of err or. The bits in the

Error register contain additional information describing the error. It is recommended that media access

commands (such as Read Sectors and Write Sectors) that end with an error condition should have the

address of the first sector in error in the command block registers.

133X CompactFlash Card

Transcend Information Inc.

¾ Device Control Register (Address - 3F6h[376h]; Offset Eh)

This register is used to control the CompactFlash Storage Card inter r u pt req ue st and to issue an ATA soft

reset to the card. This register can be written even if the device is BUSY. The bits are defined as follows:

Bit 7: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.

Bit 6: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.

Bit 5: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.

Bit 4: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.

Bit 3: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.

Bit 2 (SW R st): t his bit is s et to 1 i n orde r to f orce the CompactFlas h S t orag e C ard to pe rf orm an AT D i sk

controller Soft Reset operation. This does not change the PCMCIA Card Configuration Registers as a

hardware Reset does. The Card remains in Reset until this bit is reset to ‘0.’

Bit 1 (-IEn): the Interrupt Enable bit enables interrupts when the bit is 0. When the bit is 1, interrupts from

the CompactFlash Storage Card are disabled. This bit also controls the Int bit in the Configuration and

Status Register. This bit is set to 0 at power on and Reset.

Bit 0: this bit is ignored by the CompactFlash Storage Card.

133X CompactFlash Card

Transcend Information Inc.

¾ Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh)

This register is provided for compatibility with the AT disk drive interface. It is recommended that this

Bit 7: this bit is unknown.

Implementation Note:

Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller

operating at th e same addre sses as the CompactFlash Stor age Card. Fo llowing are som e possible

solutions to this problem for the PCMCIA implementat ion:

1) Locate the CompactFlash Storage Card at a non-conflicting address, i.e. Secondary address

(377) or in an independently decoded Address Space when a Floppy Disk Controller is located at

the Primary addresses.

2) Do not install a Floppy and a CompactFlash Storage Card in the system at the same time.

3) Implement a socket adapter that ca n be programmed to (conditionally ) tri-state D7 of I/0 address

3F7h/377 h when a CompactFlash Stora ge Card is installed and con versely to tristate D6-D0 of

I/O address 3F7h/377h when a floppy controller is installed.

4) Do not use the CompactFlash Storage Card’s Drive Address register. This may be accomplished

by either a) If p ossible, progra m the host adapt er to enable only I /O addresses 1F0h-1F7h, 3F 6h

(or 170h-177h, 176h) to the CompactFlash Storage Card or b) if provided use an additional

Primary / Secondary configuration in the CompactFlash Storage Card which does not respond to

accesses to I/O locations 3F7h and 377h. With either of these implementations, the host

software shall not attempt to use information in the Drive Address Register.

Bit 6 (-WTG): this bit is 0 when a write operation is in progress; otherwise, it is 1.

Bit 5 (-HS3): this bit is the negation of bit 3 in the Drive/Head register.

Bit 4 (-HS2): this bit is the negation of bit 2 in the Drive/Head register.

Bit 3 (-HS1): this bit is the negation of bit 1 in the Drive/Head register.

Bit 2 (-HS0): this bit is the negation of bit 0 in the Drive/Head register.

Bit 1 (-nDS1): this bit is 0 when drive 1 is active and selected.

Bit 0 (-nDS0): this bit is 0 when the drive 0 is active and selected.

133X CompactFlash Card

Transcend Information Inc.

CF-ATA Command Set

CF-ATA Command Set summarizes the CF-ATA command set with the paragraphs that follow describing the

individual commands and the task file for each.

Command Code FR SC SN CY DH LBA Status Note

1 Check Power Mode E5 or 98h – – – – Y – Support

2 Execute Drive Diagnostic 90h – – – – Y – Support

3 Erase Sector C0h – Y Y Y Y Y Support

4 Flush Cache E7h – – – – Y – NOT Support #3

5 Format Track 50h – Y – Y Y Y Support

6 Identify Device ECh – – – – Y – Support

7 Idle E3h or 97h – Y – – Y – Support

8 Idle Immediate E1h or 95h – – – – Y – Support

9 Initialize Drive Parameters 91h – Y – – Y – Support

10 Key Management

Structure Read B9 (Feature

0-127) Y Y Y Y Y – NOT Support #1

11 Key Management Read

Keying Material B9 (Feature

80) Y Y Y Y Y – NOT Support #1

12 Key Management Change

Key Management Value B9 (Feature

81) Y Y Y Y Y – NOT Support #1

13 NOP 00h – – – – Y – NOT Support

14 Read Buffer E4h – – – – Y – Support

15 Read DMA C8h – Y Y Y Y Y Support

16 Read Long Sector 22h or 23h – Y Y Y Y NOT Support #3

17 Read Multiple C4h – Y Y Y Y Y Support

18 Read Sector(s) 20h or 21h – Y Y Y Y Y Support

19 Read Verify Sector(s) 40h or 41h – Y Y Y Y Y Support

20 Recalibrate 1Xh – – – – Y – Support

21 Request Sense 03h – – – – Y – Support

22 Security Disable Password F6h – – – – Y – Support #2

23 Security Erase Prepare F3h – – – – Y – Support #2

24 Security Erase Unit F4h – – – – Y – Support #2

25 Security Freeze Lock F5h – – – – Y – Support #2

26 Security Set Password F1h – – – – Y – Support #2

27 Security Unlock F2h – – – – Y – Support #2

28 Seek 7Xh – – Y Y Y Y Support

133X CompactFlash Card

Transcend Information Inc.

29 Set Feature EFh Y – – – Y – Support

30 Set Multiple Mode C6h – Y – – Y – Support

31 Set Sleep Mode E6h or 99h – – – – Y – Support

32 Standby E2 or 96h – – – – Y – Support

33 Standby Immediate E0 or 94h – – – – Y – Support

34 Translate Sector 87h – Y Y Y Y Y Support

35 Wear Level F5h – – – – Y – Support

36 Write Buffer E8h – – – – Y – Support

37 Write DMA CAh – Y Y Y Y Y Support

38 Write Long Sector 32h or 33h – – Y Y Y Y Not Support #3

39 Write Multiple C5h – Y Y Y Y Y Support

40 Write Multiple w/o Erase CDh – Y Y Y Y Y Support

41 Write Sector(s) 30h or 31h – Y Y Y Y Y Support

42 Write Sector(s) w/o Erase 38h – Y Y Y Y Y Support

43 Write Verify 3Ch – Y Y Y Y Y Support

#1: This command is optional, depending on the key Management scheme in use.

#2: Use of this command is not recommended by CFA

#3: Use of this command is not recommended.

#4: When the controller gets this command, it will skip this command and return 0x50.

Definitions

FR = Features Register

SC =Sector Count register (00H to FFH, 00H means 256 sectors)

SN = Sector Number register

CY = Cylinder Low/Hig h register

DH = Head No. (0 to 15) of Drive/Head register

LBA = Logic Block Address Mode Support

– = Not used for the command

Y = Used for the command

133X CompactFlash Card

Transcend Information Inc.

Definitions:

FR = Features Register

SC = Sector Count RegisterS

SN = Sector Number Register

CY = Cylinder Registers

DH = Card/Drive/Head Register

LBA = Logical Block Address Mode Supported (see command descriptions for use).

Y - The register contains a valid parameter for this command. For the Drive/Head Register Y means

both the CompactFlash Storage Card and head parameters are used; D - only the

CompactFlash Storage Card parameter is valid and not the head parameter; C – The register

contains command specific data (see command descriptions for use).

 Check Power Mode - 98h or E5h

If the CompactFlash Storage Card is in, going to, or recovering from the sleep mode, the Compact Flash Storage

Card sets BSY, sets the Sector Count Register to 00h, clears BSY and generates an interrupt.

If the CompactFlash Storage Card is in Idle mode, the CompactFlash Storage Card sets BSY, sets the Sector

Count Register to FFh, clears BSY and generates an interrupt.

133X CompactFlash Card

Transcend Information Inc.

 Execute Drive Diagnostic - 90h

When the diagnostic command is issued in a PCMCIA configuration mode, this command runs only on the

CompactFlash Storage Card that is addressed by the Drive/Head register. This is because PCMCIA card

interface does not allows for direct inter-drive communication (such as the ATA PDIAG and DASP signals). When

the diagnostic command is issued in the True IDE Mode, the Drive bit is ignored a nd the diag nostic comman d is

executed by both the Master and the Slave with the Master responding with status for both devices.

Diagnostic Codes are returned in the Error Register at the end of the command.

 Erase Sector(s) - C0h

This command is used to pre-erase and condition data sectors in advance of a Write without Erase or Write

Multiple without Erase command. Ther e is no da ta transfer associated with this command but a Write Fault err or

status can occur.

133X CompactFlash Card

Transcend Information Inc.

 Flush Cache – E7h

This command causes the card to complete writing data from its cache. The card returns status with RDY=1 and

DSC=1 after the data in the write c ache buffer is written to the media. If the Compact Flash Storage Card does not

support the Flush Cache command, the Compact Flash Storage Card shall return command aborted.

 Format Track - 50h

This command writes the desired head and cylinder of the selected drive with a vendor unique data pattern

(typically FFh or 00h). To rem ain host backward compatible, the CompactFlash Storage Card expects a sector

buffer of data from the host to follow the command with the same protocol as the Write Sector(s) command

although the information in the buffer is not used by the CompactFlash Storage Card. If LBA=1 then the number of

sectors to format is taken from the Sec Cnt register (0=256). The use of this command is not recommended.

133X CompactFlash Card

Transcend Information Inc.

 Identify Device – Ech

The Identify Device command enables the host to receive parameter information from the

CompactFlash Storage Card. This command has the same protocol as the Read Sector(s) command. The

parameter words in the buffer have the arrangement and meanings defined in Table as below. All reserved

bits or words are zero. Hosts should not depend on Obsolete words in Identify Device conta ining 0. T able

47 spec ifies each fie ld in the data return ed by the Ident ify Devic e Command. In Tab le as below , X indic ates

a numeric nibble value specific to the card and aaaa indicates an ASCII string specific to the particular

drive.

Word

Address Default

Value Total

Bytes Data Field Type Information

848Ah 2 General configuration - signature for the CompactFlash 0 lash Storage Card

0 0XXX 2 General configuration – Bit Significant with ATA-4 definitions.

1 XXXXh 2 Default number of cylinders

2 0000h 2 Reserved

3 00XXh 2 Default number of heads

4 0000h 2 Obsolete

5 0000h 2 Obsolete

6 XXXXh 2 Default number of sectors per track

7-8 XXXXh 4 Number of sectors per card (Word 7 = MSW, Word 8 = LSW)

9 XXXXh 2 Obsolete

10-19 aaaa 20 Serial number in ASCII (Right Justified)

20 0000h 2 Obsolete

21 0000h 2 Obsolete

22 0004h 2 Number of ECC bytes passed on Read/Write Long Commands

23-26 aaaa 8 Firmware revision in ASCII. Big Endian Byte Order in Word

27-46 aaaa 40 Model number in ASCII (Left Justifie d) Big Endian Byte Order in Word

47 XXXXh 2 Maximum number of sectors on Read/Write Multiple command

48 0000h 2 Reserved

49 XX00h 2 Capabilities

50 0000h 2 Reserved

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

Word

Address Default

Value Total

Bytes Data Field Type Information

51 0X00h 2 P IO data transfer cycle timing mode

52 0000h 2 Obsolete

53 000Xh 2 Field Validity

54 XXXXh 2 Current numbers of cylinders

55 XXXXh 2 Current numbers of heads

56 XXXXh 2 Current sectors per track

57-58 XXXXh 4 Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW)

59 01XXh 2 Multiple sector setting

60-61 XXXXh 4 Total number of sectors addressable in LBA Mode

62 0000h 2 Reserved

63 0X0Xh 2 Multiword DMA transfer. In PC Card modes this value shall be 0h

64 00XXh 2 Advanced PIO modes supported

65 XXXXh 2

Minimum Multiword DMA transfer cycle time per word. In PC Card modes this value

shall be 0h

66 XXXXh 2

Recommended Multiword DMA transfer cycle time. In PC Card modes this

value shall be 0h

67 XXXXh 2 Minimum PI O transfer cycle time without flow control

68 XXXXh 2 Minimum PI O t ransfer cycle time with IORDY flow control

69-79 0000h 20 Reserved

80-81 0000h 4 Reserved – CF cards do not return an ATA version

82-84 XXXXh 6 Features/command sets supported

85-87 XXXXh 6 Features/command sets enabled

88 XXXXh 2 Ultra DMA M ode Supported and Selected

89 XXXXh 2 T ime required for Security erase unit completion

90 XXXXh 2 T ime required for Enhanced security erase unit completion

91 XXXXh 2 Current Advanced power management value

92-127 0000h 72 Reserved

128 XXXXh 2 Security status

129-159 0000h 64 Vendor unique bytes

160 XXXXh 2 Power requirement description

161 0000h 2 Reserved for assignment by the CFA

162 0000h 2 K ey management schemes supported

163 XXXXh 2 CF Advanced True IDE Timing Mode Capability and Setting

164 XXXXh 2 CF Advanced PC Card I/O and Memory Timing Mode Capability

165-167 0000h 6 Reserved for assignment by the CFA

168-255 0000h 158 Reserved

133X CompactFlash Card

Transcend Information Inc.

¾ Word 0: General Configuration

This field indicates the general characteristics of the device. When Word 0 of the Identify drive information

is 848Ah then the device is a CompactFlash Storage Card and com plies with the CFA specification and

CFA command set. It is recommended that PCMCIA modes of op eration r ep ort only the 848 Ah value a s

they are always intended as removable devices.

Bits 15-0: CF Standard Configuration Value

Word 0 is 848Ah. This is the recommended value of Word 0.

Some operating systems require Bit 6 of Word 0 to be set to 1 (Non-removable device) to use the card as

the root storage device. The Card must be the root storage device when a host completely replaces

conventional disk storage with a CompactFlash Card in True IDE mode. To support this requirement and

provide capability for any future removable media Cards, alternatehandling of Word 0 is permitted.

Bits 15-0: CF Preferred Alternate Configuration Values

044Ah: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and

Removable D e vic e w h ile pres ervi ng all Retired bits in the word.

0040h: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and

Removable Device w hile zeroing all Retired bits in the word

Bit 15-12: Configuration Flag

If bits 15:12 are set to 8h then Word 0 shall be 848Ah.

If bits 15:12 are set to 0h then Bits 11:0 are set using the definitions below and the Card is requ ired to

support for the CFA command set and report that in bit 2 of Word 83.

Bit 15:12 values other than 8h and 0h are prohibited.

Bits 11-8: Retired

These bits have retired ATA bit definitions. It is recommended that the value of these bits be either the

preferred value of 0h or the value of 4h that preserves the corresponding bits from the 848Ah CF

signature value.

Bit 7: Removable Media Device

If Bit 7 is set to 1, the Card contains media that can be removed during Card operation.

If Bit 7 is set to 0, the Card contains nonremovable media.

Bit 6: Not Removable Controller and/or Device

Alert! This bit will be considered for obsolescence in a future revision of this standard.

If Bit 6 is set to 1, the Card is intended to be nonremovable during operation.

If Bit 6 is set to 0, the Card is intended to be removable during operation.

Bits 5-0: Retired/Reserved

Alert! Bit 2 will be considered for definition in a future revision of this standard and shall be 0 at this

time.

Bits 5-1 have retired ATA bit definitions.

Bit 2 shall be 0.

Bit 0 is Reserved and shall be 0.

It is recommended that the value of bits 5-0 be either the preferred value of 00h or the value of 0Ah that

preserves the corresponding bits from the 848Ah CF signature value.

¾ Word 1: Default Number of Cylinders

This field contains the number of translated cylinders in the default translation mode. This value will be the

same as the number of cylinders.

¾ Word 3: Default Number of Heads

This field contains the number of translated heads in the default translation mode.

¾ Word 6: Default Number of Sectors per Track

This field contains the number of sectors per track in the default translation mode.

133X CompactFlash Card

Transcend Information Inc.

¾ Words 7-8: Number of Sectors per Card

This field contain s the num ber of sec to rs per C omp ac tF las h St orage Card. This double word

value is also the first invalid address in LBA translation mode.

¾ Words 10-19: Serial Number

This field contains the serial number for this CompactFlash Storage Card and is right justified and padded

with spaces (20h).

¾ Word 22: ECC Count

This field defines the number of ECC bytes used on each sector in the Read and Write Long commands.

This value shall be set to 0004h.

¾ Words 23-26: Firmware Revision

This field contains the revision of the firmware for this product.

¾ Words 27-4 6: Mod el Nu m ber

This field contains the model number for this product and is left justified and padded with spaces (20h).

¾ Word 47: Read/Write Multiple Sector Count

Bits 15-8 shall be the recommended value of 80h or the permitted value of 00h. Bits 7-0 of this word define

the maximum number of se ctors per block that the CompactFlash Storage Card supports for Read/Write

Multiple commands.

¾ Word 49: Capabilities

Bit 13: Standby Ti mer

If bit 13 is set to 1 then the Standby timer is supported as defined by the IDLE command

If bit 13 is set to 0 then the Standby timer operation is defined by the vendor.

Bit 11: IORDY Supported

If bit 11 is set to 1 then this CompactFlash Storage Card supports IORDY operation.

If bit 11 is set to 0 then this CompactFlash Storage Card may support IORDY operation.

Bit 10: IORDY may be disabled

Bit 10 shall be set to 0, indicating that IORDY may not be disabled.

Bit 9: LBA supported

Bit 9 shall be set to 1, indicating that this CompactFlash Storage Card supports LBA mode addressing. CF

devices shall support LBA addressing.

Bit 8: DMA Supported If bit 8 is set to 1 then Read DMA and Write DMA commands are suppor ted. Bit 8

shall be set to 0. Read/Write DMA commands are not currently permitted on CF cards.

¾ PIO Data Transfer Cycle Timing Mode

The PIO transfer timing for each CompactFlash Storage Card falls into modes that have unique

parametric timing specifications. The value re turned in Bits 1 5-8 shall be 00h f or mode 0, 01h f or mode 1,

or 02h for mode 2. Values 03h through FFh are reserved.

¾ Translation Parameters Valid

Bit 0 shall be set to 1 indicating that words 54 to 58 are valid and reflect the current numb er o f cylinde rs,

heads and sectors. If bit 1 of word 53 is set to 1, the values in words 64 th ro ug h 70 are valid. If th is b it is

cleared to 0, the values reported in words 64-70 are not valid. Any CompactFlash Storage Card that

supports PIO mode 3 or above shall set bit 1 of word 53 to one and support the fields contained in words

64 through 70.

¾ Current Number of Cylinders, Heads, Sectors/Track

These fields contain s the current num ber of user ad dressable Cylinders, Heads, and Sectors/Track in the

current translation mode.

¾ Current Capacity

This field contains the product of the current cylinders times heads times sectors.

133X CompactFlash Card

Transcend Information Inc.

¾ Multiple Sector Setting

Bits 15-9 are reserved and shall be set to 0.

Bit 8 shall be set to 1 indicating that the Multiple Sector Setting is valid.

Bits 7-0 are the current setting for the number of sectors that shall be transferred per interrupt on

Read/Write Multiple commands.

¾ Total Sectors Addressable in LBA Mode

This field contains the total number of user a ddressable sectors for the CompactFlash Storage Card in

LBA mode only.

¾ Multiword DMA transfer

Bits 15 through 8 of word 63 of the Identify Device parameter information is defined as the Multiword DMA

mode selected field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant.

Only one of bits may be set to one in this field by the CompactFlash Storage Card to indicate the

multiword DMA mode which is currently selected. Of these bits, bits 15 through 11 are reserved. Bit 8 , if

set to one, indicates that Multiword DMA mode 0 has been selected. Bit 9, if set to one, indicates that

Multiword DMA mode 1 has been selected. Bit 10, if set to one, indicates that Multiword DMA mode 2 has

been selected.

Selection of Multiword DMA modes 3 and above are specific to CompactFlash are r epo rte d in word 163 ,

Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings.

Bits 7 thro ugh 0 o f word 63 of the Identify Dev ice pa ramet er information is def ined as th e Multiw ord DMA

data tran sfer supp orted field. If this field is supporte d, bit 1 of word 53 shall be set to o ne. This field is bit

significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to

indicate the Multiword DMA modes it is capabl e of supporting.

Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage

Card supports Multiword DMA mode 0. Bit 1, if set to one, indicates that the CompactFlash Storage Card

supports Multiword DMA modes 1 and 0. Bit 2, if set to one, indicates that the CompactFlash Storage

Card supports Multiword DMA modes 2, 1 and 0. Support for Multiword DMA modes 3 and above are

specific to CompactFlash are reported in word 163, Word 163: CF Advanced True IDE Timing Mode

Capabilities and Settings.

¾ Word 64: Advanced PIO transfer modes supported

Bits 7 through 0 of word 64 of the Identify Device parameter informa tion is defined as th e advanced PIO

data tran sfer supp orted field. If this field is supporte d, bit 1 of word 53 shall be set to o ne. This field is bit

significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to

indicate the advanced PIO modes it is capable of supporting.

Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage

Card supports PIO mode 3. Bit 1, if set to one, indicates that the CompactFlash StorageCard supports

PIO mode 4.

Support for PIO modes 5 and above are specific to CompactFlash are reported in word 163.

¾ Word 65: Minimum Multiword DMA transfer cycle time

Word 65 of the parameter information of the Identify Device command is defined as the minimum

Multiword DMA transfer cycle time. This field defines, in nanoseconds, the minimum cycle time that, if

used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer.

If this field is supported, bit 1 of w ord 53 shall be set to one. The value in w ord 65 shall not be less th an the

minimum cycle time for the fastest DMA mode supported by the device. This field shall be supported by all

CompactFlash Storage Cards supp orting DMA m odes 1 and above. If bit 1 of word 53 is set to one, but

this field is not supported, the Card shall return a value of zero in this field.

¾ Recommended Multiword DMA transfer cycle time

Word 66 of the parameter information of the Identify Device command is defined as the recommended

Multiword DMA transfer cycle time. This field defines, in nanoseconds, the cycle time that, if used by the

host, may optimize the data transfer from by reducing the probability that the CompactFlash Storage Card

133X CompactFlash Card

Transcend Information Inc.

will need to negate the DMAR Q signal during the transfer of a sector.

If this field is supported, bit 1 of w ord 53 shall be set to one. The value in w ord 66 shall not be less th an the

value in word 65. This field shall be supported by all CompactFlash Storage Cards supporting DMA

modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a

value of zero in this field.

¾ Word 67: Minimum PIO transfer cycle time without flow control

Word 67 of the parameter information of the Identify Device command is defined as the minimum PIO

transfer w ithout flow c ontrol cycle time. This fiel d defines, in nanoseconds, t he minimum cyc le time that, if

used by the host, the CompactFlash Storage Card guarante es data integrity during the transfer without

utilization of flow cont rol. If this field is supported, Bit 1 of w ord 53 shall be set to one. Any CompactFlash

Storage Card that supp orts PIO mode 3 or above shall support th is field, and the value in word 67 shall

not be less than the value repo rted in word 68. If bit 1 of word 53 is set to one because a Com pactFlash

Storage Card supports a field in words 64-70 other than this field and the CompactFlash Storage Card

does not support this field, the CompactFlash Storage Card sh all return a value of zero in this field.

¾ Word 68: Mini mum PIO transfer cycle time with IORDY

Word 68 of the parameter information of the Identify Device command is defined as the minimum PIO

transfer with IORDY flow control cycle time. This fie ld defines, in na noseconds, the min imum cycle time

that the CompactFlash Storage Card supports while perf orming data transfers while utilizing IORDY flow

control. If this field is supported, Bit 1 of word 53 shall be set to one. Any CompactFlash Storage Card that

supports PIO mode 3 or above shall support this field, and the value in word 68 shall be the fastest defined

PIO mode supported by the CompactFlash Storage Card. If bit 1 of word 53 is set to one because a

CompactFlash Storage Card supports a field in words 64-70 other than this field and the CompactFlash

Storage Card does no t support this field, the Comp actFlash Storage Card shall return a value of zero in

this field.

¾ Words 82-84: Features/command sets supported

Words 82, 83, and 84 shall indicate features/command sets supp orted. The value 0000h or FFF Fh was

placed in each of these words by CompactFlash Storage Cards prior to ATA-3 and shall be interpreted by

the host as meaning that featu res/command sets supp orted are not indicated . Bits 1 throu gh 13 of word

83 and bits 0 through 13 of word 84 are reserved. Bit 14 of word 83 and word 84 shall be set to one and bit

15 of word 83 and word 84 shall be cleared to zero to provide indication that the features/command sets

supported words are valid. The values in these words should not be depended on by host implementers.

Bit 0 of word 82 shall be set to zero; the SMART feature set is not supported.

If bit 1 of word 82 is set to one, the Security Mode feature set is supported.

Bit 2 of word 82 shall be set to ze ro; the Re mova bl e Media feat ure s et is not s upport ed.

Bit 3 of word 82 shall be set to one; the Powe r Management feat ure set is supported.

Bit 4 of word 82 shall be set to zero; the Packet Command feature set is not supported.

If bit 5 of word 82 is set to one, write cache is supported.

If bit 6 of word 82 is set to one, look-ahead is supported.

Bit 7 of word 82 shall be set to ze ro; releas e inte rrupt is not supp orted.

Bit 8 of word 82 shall be set to zero; Service interrupt is not supported.

Bit 9 of word 82 shall be set to zero; the Device Reset command is not supported.

Bit 10 of word 82 shall be set to zero; the Host Protected Area feature set is not supported.

Bit 11 of word 82 is obsolete.

Bit 12 of word 82 shall be set to one; the CompactFlash Storage Card supports the Write Buffer

command.

Bit 13 of word 82 shall be set to one; the CompactFlash Storage Card supports the Read Buffer

command.

Bit 14 of word 82 shall be set to one; the CompactFlash Storage Card supports the NOP command.

Bit 15 of word 82 is obsolete.

Bit 0 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Download

133X CompactFlash Card

Transcend Information Inc.

Microc od e com ma nd .

Bit 1 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA

Queued and Write DMA Queued commands.

Bit 2 of word 83 shall be set to one; the CompactFlash Storage Card supports the CFA feature set.

If bit 3 of word 83 is set to one, the CompactFlash Storage Card supports the Advanced Power

Management feature set.

Bit 4 of word 83 shall be set to zero; the CompactFlash Storage Card does not supp ort the Removable

Media Status feature set.

¾ Words 85-87: Features/command sets enabled

Words 85, 86, and 87 shall indicate features/command sets enabled. The value 0000h or FFFFh was

placed in each of these words by CompactFlash Storage Cards prior to ATA-4 and shall be interpreted by

the host as meaning that features/command sets enabled are not indicated. Bits 1 through 15 of word 86

are reserved. Bits 0-13 of word 87 are reserved. Bit 14 of word 87 shall be set to one and bit 15 of word 87

shall be cleared to zero to provide indication that the features/command sets enabled words are valid.

The values in thes e words should no t be depe nd ed on by ho s t im pleme nt ers.

Bit 0 of word 85 shall be set to zero; the SMART feature set is not enabled.

If bit 1 of word 85 is set to one, the Security Mode feature set has been enabled via the Security Set

Password command.

Bit 2 of word 85 shall be set to zero; the Removabl e Media feature set is not sup po rted.

Bit 3 of word 85 shall be set to one; the Powe r Management feat ure set is supported.

Bit 4 of word 85 shall be set to zero; the Packet Command feature set is not enabled.

If bit 5 of word 85 is set to one, write cache is enabled.

If bit 6 of word 85 is set to one, look-ahead is enabled.

Bit 7 of word 85 shall be set to zero; release interrupt is not enabled.

Bit 8 of word 85 shall be set to zero; Service interrupt is not enabled.

Bit 9 of word 85 shall be set to zero; the Device Reset command is not supported.

Bit 10 of word 85 shall be set to zero; the Host Protected Area feature set is not supported.

Bit 11 of word 85 is obsolete.

Bit 12 of word 85 shall be set to one; the CompactFlash Storage Card supports the Write Buffer

command.

Bit 13 of word 85 shall be set to one; the CompactFlash Storage Card supports the Read Buffer

command.

Bit 14 of word 85 shall be set to one; the CompactFlash Storage Card supports the NOP command.

Bit 15 of word 85 is obsolete.

Bit 0 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Download

Microc od e com ma nd .

Bit 1 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA

Queued and Write DMA Queued commands.

If bit 2 of word 86 shall be set to one, the CompactFlash Storage Card supports the CFA feature set.

If bit 3 of word 86 is set to one, the Advanced Power Management feature set has been en abled via the

Set Features command.

Bit 4 of word 86 shall be set to zero; the CompactFlash Storage Card does not supp ort the Removable

Media Status feature set.

¾ Word 88: Ultra DMA Modes Supported and Selected

Word 88 identifies the Ultra DMA transfe r mod es supp or ted by the device and indicates the mod e tha t is

currently selected. Only one DMA mode shall be selected at any given time. If an Ultra DMA mode is

selected, then no Multiword DMA mode shall be selected. If a Multiword DMA mode is selected, then no

Ultra DMA mode shall be selected. Support of this word is mandatory if Ultra DMA is supported.

Bits 15-13: Reserved

Bit 12: 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected

133X CompactFlash Card

Transcend Information Inc.

Bit 11: 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected

Bit 10: 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected

Bit 9: 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected

Bit 8: 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected

Bits 7-5: Reserved

Bit 4: 1 = Ultra DMA mode 4 and be low are supported. Bits 0-3 Sha ll be set to 1.

Bit 3: 1 = Ultra DMA mode 3 and be low are supported, Bits 0-2 Sha ll be set to 1.

Bit 2: 1 = Ultra DMA mode 2 and be low are supported. Bits 0-1 Sha ll be set to 1.

Bit 1: 1 = Ultra DMA mode 1 and below are supported. Bit 0 Shall be set to 1.

Bit 0: 1 = Ultra DMA mode 0 is supported

¾ Word 89: Time required for Security erase unit completion

Word 89 specifies the time required for the Security Erase Unit command to complete. This command

shall be supported on CompactFlash Storage Cards that support security.

Value Time

0 Value not specified

1-25

4 (Value * 2) minutes

255 >508 minutes

¾ Word 90: Time required for Enhanced security erase unit completion

Word 90 specifies the time required for the Enhanced Security Erase Unit command to complete.

This command shall be supported on CompactFlash Storage Cards that support security.

Value Time

0 Value not specified

1-25

4 (Value * 2) minutes

255 >508 minutes

¾ Word 91: Advanced power management level value

Bits 7-0 of word 91 contain the current Advanced Power Management level setting.

¾ Word 128: Security Status

Bit 8: Security Level

If set to 1, indicates that security mode is enabled and the security level is maximum.

If set to 0 and security mode is enabled, indicates that the security level is high.

Bit 5: Enhanced security erase unit feature supported

If set to 1, indicates that the Enhanced security erase unit feature set is supported.

Bit 4: Expire

If set to 1, indicates that the security count has expired and Security Un lock and Security Er ase Unit a re

command aborted until a power-on reset or hard reset.

Bit 3: Freeze

If set to 1, indicates that the security is Frozen.

Bit 2: Lock

If set to 1, indicates that the security is locked.

Bit 1: Enable/Disable

If set to 1, indicates that the security is enabled.

If set to 0, indicates that the security is disabled.

Bit 0: Capability

If set to 1, indicates that CompactFlash Storage Card supports security mode feature set.

If set to 0, indicates that CompactFlash Storage Card does not support security mode feature set.

¾ Word 160: Power Requirement Description

133X CompactFlash Card

Transcend Information Inc.

This word is required for CompactFlash Storage Cards that support power mode 1.

Bit 15: VLD

If set to 1, indicates that this word contains a valid power requirement description.

If set to 0, indicates that this word does not contain a power requirement description.

Bit 14: RSV

This bit is reserved an d shall be 0.

Bit 13: -XP

If set to 1, indicates that the CompactFlash Storage Card does not have Power Level 1 commands.

If set to 0, indicates that the CompactFlash Storage Card has Power Level 1 commands

Bit 12: -XE

If set to 1, indicates that Power Level 1 commands are disabled.

If set to 0, indicates that Power Level 1 commands are enabled.

Bit 0-11: Maximu m c urren t

This field contains the CompactFlash Storage Card’s maximum current in mA.

¾ Word 162: Key Management Schemes Supported

Bit 0: CPRM support

If set to 1, the device supports CPRM Scheme (Content Protection for Recordable Media)

If set to 0, the device does not support CPRM.

Bits 1-15 are reserved for future additional Key Management schemes.

¾ Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings

This word describes the capabilities and current settings for CFA defined advanced timing modes using

the True IDE interface.

Notice! The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above

impose significant restrictions on the implementation of the host:

Additional Requirements for CF Advanced Timing Modes.

There are four separate fields defined that describe support and selection of Advanced PIO timing modes

and Advanced Multiword DMA timing modes. The older modes are reported in words 63 and 64.

Word 63: Multiword DMA transfer and 6.2.1.6.19: Word 64: Advanced PIO transfer modes supported.

Bits 2-0: Advanced True IDE PIO Mode Support Indicates the maximum True IDE PIO mode supported by

the card. Value Maximum PIO mode timing selected

0 Specified in word 64

1 PIO Mode 5

2 PIO Mode 6

3-7 Reserved

Bits 5-3: Advanced True IDE Multiword DMA Mo de Suppor t Indicates the maximum Tr ue IDE Multiword

DMA mode supported by the card.

Value Maximum Multiword DMA timing mode supported

0 Specified in word 63

1 Multiword DMA Mode 3

2 Multiword DMA Mode 4

3-7 Reserved

Bits 8-6: Advanced True IDE PIO Mode Selected Ind icates the current True IDE PIO mode selected on

the card. Value Current PIO timing mode selected

0 Specified in word 64

1 PIO Mode 5

133X CompactFlash Card

Transcend Information Inc.

2 PIO Mode 6

3-7 Reserved

Bits 11-9: Advanced True IDE Multiword DMA Mode Selected Indicates the curr ent True IDE Multiword

DMA Mode Selected on the card.

Value Current Multiword DMA timing mode selected

0 Specified in word 63

1 Multiword DMA Mode 3

2 Multiword DMA Mode 4

3-7 Reserved

Bits 15-12 are reserved.

¾ Word 164: CF Advanced PCMCIA I/O and Memory Timing Modes Capabilities and Settings

This word describes the capabilities and current settings for CFA defined advanced timing modes using

the Memory and PCMCIA I/O interface.

Notice! The use of PCMCIA I/O or Memory modes that are 100ns or faster impose significant

restrictions on the implementation of the host:

Additional Requirements for CF Advanced Timing Modes.

Bits 2-0: Maximum Advanced PCMCIA I/O Mode Support Indicates the maximum I/O timing mode

supported by the card.

Value Maximum PCMCIA IO timing mode Supported

0 255ns Cycle PCMCIA I/O Mode

1 120ns Cycle PCMCIA I/O Mode

2 100ns Cycle PCMCIA I/O Mode

3 80ns Cycle PCMCIA I/O Mode

4-7 Reserved

Bits 5-3: Maximum Memory timing mode supported

Indicates the Maximum Memory timing mode supported by the card.

Bits 15-6: Reserved.

Value Maximum Memory timing mode Supported

0 250ns Cycle Memory Mode

1 120ns Cycle Memory Mode

2 100ns Cycle Memory Mode

3 80ns Cycle Memory Mode

4-7 Reserved

 Idle - 97h or E3h

This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and

generate an in te rrupt. If t he s ec to r c ount is no n-ze ro, it is inte rp rete d as a t im er co unt with each count being 5

milliseconds and the automatic power down mode is enabled. If the sector count is zero, the automatic power

down mode is disabled. Note that this time base (5 msec) is different from the ATA specification.

133X CompactFlash Card

Transcend Information Inc.

 Idle Imm ediate - 95h or E1h

This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and

generate an interrupt.

 Initialize Drive Parameters - 91h

This command enables the host to set the number of sectors per track and the number of heads per cylinder.

Only the Sector Count and the Card/Drive/Head registers are used by this command.

 NOP - 00h

This command always fails with the CompactF lash Storage Card returning command aborted.

133X CompactFlash Card

Transcend Information Inc.

 Read Buffer - E4h

The Read Buffer command enables the host to read the current contents of the CompactFlash Storage Card’s

sector buffer. This command has the same protocol as the Read Sector(s) command.

 Read DMA – C8h

 Read Long Sector - 22h or 23h

133X CompactFlash Card

Transcend Information Inc.

 Read Multiple - C4h

 Read Sector(s) - 20h or 21h

 Read Verify Sector(s) - 40h or 41h

 Recalibrate - 1Xh

 Request Sense - 03h

133X CompactFlash Card

Transcend Information Inc.

The extended error code is returned to the host in the Error Register.

 Seek - 7Xh

 Set Features – EFh

133X CompactFlash Card

Transcend Information Inc.

Feature Supported

Features 01h and 81h are used to enable and clear 8 bit data transfer modes in True IDE Mode. If the 01h

feature command is issued all data transfers shall occur on the low order D[7:0] data bus and the -IOIS16

signal shall not be asserted for data register accesses. The host shall not enable this feature for DMA

transfers.

Features 02h and 82h allow the host to enable or disable write cache in CompactFlash Storage Cards that

implement write cache. When the subcommand disable w rite cache is issued, the CompactFlash Storage Card

shall initiate the sequence to flush cache to non-volatile memory before command completion.

133X CompactFlash Card

Transcend Information Inc.

Feature 03h allows the host to select the PIO or Multiword DMA transfer mode by specifying a value in the

Sector Count register. The up per 5 bits define the type of transfer and the lo w order 3 bits encode the mode

value. One PIO mode shall be selected at all times. For Cards which support DMA, one Multiword DMA mode

shall be selected at all times. The host may change the selected modes by the Set Features command.

 Set Multiple Mode - C6h

 Set Sleep Mode- 99h or E6h

 Standby - 96h or E2h

133X CompactFlash Card

Transcend Information Inc.

133X CompactFlash Card

Transcend Information Inc.

 Standby Immediate - 94h or E0h

 Translate Sector - 87h

Translate Sector Information

133X CompactFlash Card

Transcend Information Inc.

 Wear Level - F5h

 Write Buffer - E8h

 Write DMA – CAh

133X CompactFlash Card

Transcend Information Inc.

 Write Long Sector - 32h or 33h

 Write Multiple Command - C5h

 Write Multiple without Erase – CDh

133X CompactFlash Card

Transcend Information Inc.

 Write Sector(s) - 30h or 31h

 Write Sector(s) without Erase - 38h

 Write Verify - 3Ch

133X CompactFlash Card

Transcend Information Inc.

 Error Posting

133X CompactFlash Card

Transcend Information Inc.

Error and Status Register summarizes the valid status and error value for all the CF-ATA Command set.

C.H.S. Table

Capacity C H S

1GB 1942 16 63

2GB 3884 16 63

4GB 7769 16 63

8GB 15538 16 63

16GB 16383 15 63

32GB 16383 15 63

133X CompactFlash Card

Transcend Information Inc.

SMART Command Set

z SMART Command Set

SMART Feature Register Values

D0h Read Data D4h Execute OFF-LINE Immediate

D1h Read Attribute Threshold D8h Enable SMART Operations

D2h Enable/Disable Autosave D9h Disable SMART Operations

D3h Save Attribute Values DAh Return Status

1. If reserved size is below the Threshold, the status can be read from Cylinder register by Return Status command

(DAh).

z SMART Data Structure

BYTE F / V Decription

0-1 X Revision code

2-361 X Vendor specific

362 V Off line data collection status

363 X Self-test execution status byte

364-365 V Total time in seconds to complete off-line data collection activity

366 X Vendor specific

367 F Off-line data collection capability

368-369 F SMART capability

370 F Error logging capability

7-1 Reserved

0 1=Device error logging supported

371 X Vendor specific

372 F Short self-test routine recommended polling time (in minutes)

373 F Extended self-test routine recommended polling time (in minutes)

374 F Conveyance self-test routine recommended polling time (in minutes)

375-385 R Reserved

386-395 F Date Code

396 V Number of MU in dev ice (0~n)

397+(n*6) V MU number

398+(n*6) V MU data block

400+(n*6) V MU spare block

401+(n*6) V Init. Bad block

402+(n*6) V Last Defect Bad block ( Newest state)

133X CompactFlash Card

Transcend Information Inc.

511 V Data structure checksum

F=the content of the byte is fixed and does not change.

V=the content of the byte is variable and may change depending on the state of the device or

the commands executed by the device.

X=the content of the byte is vendor specific and may be fixed or variable.

R=the content of the byte is reserved and shall be zero.

* 4 Byte value : [MSB] [2] [1] [LSB]

The above technical information is based on industry standard data and has been tested to be reliable. However,

Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection

with the use of this product. Transcend reserves the right to make changes to the specifications at any time without

prior notice.

133X CompactFlash Card

Transcend Information Inc.

Ordering Information

JAPAN

E-mail: sales@transcend.co.jp

www.transcend.jp

CHINA

E-mail: sales@transcendchina.com

www.transcendchina.com

GERMANY

E-mail: vertrieb@transcend.de

www.transcend.de

HONG KONG

E-mail: sales@transcend.com.hk

www.transcendchina.com

TAIWAN

No.70, Xing Zhong Rd., NeiHu Dist., Ta ipei, Taiwan, R.O.C

TEL +886-2-2792-8000

Fax +886-2-2793-2222

E-mail: sales@transcend.com.tw

www.transcend.com.tw Korea

E-mail: sales@transcend.co.kr

www.transcend.co.kr

THE NETHERLANDS

E-mail: sales@transcend.nl

www.transcend.nl

USA

Los Angeles:

E-mail: sales@transcendusa.com

Maryland:

E-mail: sales_md@transcendusa.com

www.transcendusa.com United Kingdom

E-mail: sales@transcend-uk.com

www.transcend-uk.com

TS XG CF133 XX

Capacity:

1G-16G = 1GB up to 16GB Com

actFlash Card 133X

Transcend Product

Form Factor

-S = SLC

-M = MLC

-I = Industrial (SLC)