POLY-FUSE(R) Resettable PTCs Surface Mount > 2016L Series 2016L Series RoHS Description The 2016L Series PTC provides surface mount overcurrent protection for low voltage (60V) applications where resettable protection is desired. Features * RoHS compliant, lead-free and halogen-free * Fast response to fault currents Agency Approvals AGENCY * High voltage * Low-profile Applications * Low voltage telecom equipment protection * IEEE 1394 port protection *P owered ethernet port protection (IEEE 802.3 af) * Automotive electronic control module protection AGENCY FILE NUMBER E183209 R50119118 Electrical Characteristics Part Number Marking I hold (A) 2016L030 LF030 0.30 0.60 60 20 2016L050 LF050 0.55 1.10 60 20 I trip (A) V max (Vdc) I max (A) P d typ. (W) Maximum Time To Trip Resistance Agency Approvals Current (A) Time (Sec.) R min () R 1max () 1.40 1.5 3.0 0.500 2.300 X X 1.40 2.5 5.0 0.200 1.000 X X X 2016L075/60 LF075 0.75 1.50 60 20 1.40 8.0 0.5 0.130 0.900 X 2016L100 LF100 1.10 2.20 15 40 1.40 8.0 0.5 0.100 0.400 X X 2016L100/33 LF100-33 1.10 2.20 33 40 1.40 8.0 0.5 0.100 0.400 X X 2016L150 LF150 1.50 3.00 15 40 1.40 8.0 1.0 0.070 0.180 X X 2016L150/33 LF150-33 1.50 3.00 33 40 2.0 8.00 1.00 0.070 0.180 X X X 2016L200 LF200 2.00 4.20 6 40 1.40 8.0 3.0 0.048 0.100 X 2016L260/24 LF260-24 2.60 5.00 24 40 1.6 8.00 5.00 0.025 0.075 X X 2016L300/16 LF0300 3.00 5.00 16 40 1.6 8.00 10.00 0.015 0.048 X X 0.025 X X 2016L500 LF500 5.00 10.00 6 100 2.0 25.00 2.00 0.005 I hold = Hold current: maximum current device will pass without tripping in 20C still air. I trip = Trip current: minimum current at which the device will trip in 20C still air. V max = Maximum voltage device can withstand without damage at rated current (I max) I max = Maximum fault current device can withstand without damage at rated voltage (Vmax) P d = Power dissipated from device when in the tripped state at 20C still air. R min = Minimum resistance of device in initial (un-soldered) state. R typ = Typical resistance of device in initial (un-soldered) state. R 1max = M aximum resistance of device at 20C measured one hour after tripping or reflow soldering of 260C for 20 sec. Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. * Agency Approval is Pending WARNING * Users shall independently assess the suitability of these devices for each of their applications * Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fire * These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such conditions are expected to be repetitive or prolonged in duration * Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices * These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses * Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device. (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/22/17 POLY-FUSE(R) Resettable PTCs Surface Mount > 2016L Series Temperature Rerating Ambient Operation Temperature -40C -20C 0C 20C 40C 50C 60C 70C 85C Hold Current (A) Part Number 2016L030 0.45 0.40 0.35 0.30 0.25 0.23 0.20 0.18 0.14 2016L050 0.93 0.80 0.65 0.50 0.42 0.38 0.33 0.30 0.23 2016L075/60 1.21 1.06 0.91 0.75 0.61 0.54 0.45 0.38 0.26 2016L100 1.66 1.47 1.29 1.10 0.91 0.83 0.73 0.64 0.50 2016L100/33 1.66 1.47 1.29 1.10 0.91 0.83 0.73 0.64 0.50 2016L150 2.26 2.00 1.76 1.50 1.24 1.13 1.00 0.87 0.68 2016L150/33 2.25 2.05 1.79 1.50 1.31 1.17 1.05 0.93 0.72 2016L200 2.80 2.50 2.19 2.00 1.84 1.74 1.50 1.34 1.14 2016L260/24 3.80 3.43 3.04 2.60 2.24 2.03 1.82 1.64 1.25 2016L300/16 4.32 3.93 3.57 3.00 2.58 2.40 2.22 1.89 1.68 2016L500 7.20 6.55 5.95 5.00 4.30 4.00 3.70 3.15 2.80 Temperature Rerating Curve Average Time Current Curves Time in Seconds 100 10 150% Percentage of Rated Current 1.50A/33 2.60A/24 3.00A/16 5.00A 0.30A 0.50A 0.75A/60 1.00A 1.00A/33 1.50A 2.00A 170% 130% 110% 90% 70% 50% 30% 10% -40 -30 -20 -10 0 1 10 20 30 40 Temperature (C) 50 60 70 80 85 Note: Typical Temperature rerating curve, refer to table for derating data 0.1 Additional Information 0.01 0.1 1 10 Current in Amperes The average time current curves and Temperature Rerating curve performance is affected by a number or variables, and these curves provided as guidance only. Customer must verify the performance in their application. Datasheet Resources Samples (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/22/17 POLY-FUSE(R) Resettable PTCs Surface Mount > 2016L Series Soldering Parameters Profile Feature Pb-Free Assembly Average Ramp-Up Rate (TS(max) to TP) 3C/second max 150C Temperature Max (Ts(max)) 200C Time (Min to Max) (ts) 60 - 180 secs Time Maintained Above: Temperature (tL) 217C Peak / Classification Temperature (TP) 260 Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Temperature (TL) 60 - 150 seconds +0/-5 C Physical Specifications Critical Zone tL to tP Ramp-up TL TS(max) Temperature Pre Heat: Temperature Min (Ts(min)) tP TP tL Ramp-do Ramp-down Preheat TS(min) 25 tS time to peak temperature Time -- All temperature refer to topside of the package, measured on the package body surface -- If reflow temperature exceeds the recommended profile, devices may not meet the performance requirements -- Recommended reflow methods: IR, vapor phase oven, hot air oven, N2 environment for lead -- Recommended maximum paste thickness is 0.25mm(0.010inch) -- Devices can be cleaned usingstandard industry methods and solvents -- Devices can be reworked using the standard industry practices Environmental Specifications Terminal Material Solder-Plated Copper (Solder Material: Matte Tin(Sn)) Operating/Storage Temperature -40C to +85C Lead Solderability Meets EIA Specification RS186-9E, ANSI/ J-STD-002 Category 3. Maximum Device Surface Temperature in Tripped State 125C Passive Aging +85C, 1000 hours -/+5% typical resistance change Humidity Aging +85C, 85%,R.H.,1000 hours -/+5% typical resistance change Thermal Shock MIL-STD-202, Method 107 +85C/-40C 20 times -30% typical resistance change Solvent Resistance MIL-STD-202, Method 215 No change Vibration MIL-STD-883, Method 2007, Condition A No change Moisture Sensitivity Level Level 1, J-STD-020 (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/22/17 POLY-FUSE(R) Resettable PTCs Surface Mount > 2016L Series Dimensions (mm) C A Top View 100 Bottom View 100 100 -33 B 3.40 mm (.133") Pad Layout D E 4.60 mm (.181") 1.50 mm (.059") A Part Number Inches MARKING CODE VARIES WITH AMPERAGE AND VOLTAGE RATING SEE ELECTRICAL CHARACTERISTICS CHART SHOWN ARE: - 1.1A/15V RATING (LEFT) - 1.1A/33V RATING (RIGHT) Side View B mm Inches C mm mm Min Max Min Max Min Max Min Max Min Max 2016L030 2016L050 2016L075/60 2016L100 2016L100/33 0.19 0.21 4.72 5.44 0.15 2016L150 2016L150/33 2016L200 2016L260/24 2016L300/16 2016L500 0.17 3.7 D Inches Inches Min Max Min 0.05 0.08 0.08 0.03 0.05 0.06 0.06 0.03 0.75 1.20 1.20 0.50 0.75 0.75 0.80 0.50 1.25 2.00 2.00 0.75 1.25 1.55 0.01 1.60 0.75 4.43 0.03 0.06 0.80 1.60 0.03 0.05 0.05 4.43 0.02 0.03 0.03 4.43 0.03 4.43 0.02 E mm Inches mm Max Min Max Min Max Min Max 0.06 0.3 1.5 0.01 0.03 0.25 0.65 Part Ordering Number System 2016 L xxx /xx D R - A SERIES -A: Automotive grade Blank: Standard version PACKAGING STYLE R: Tape & Reel QUANTITY CODE: D=1500 M=1000 P=2000 SPECIAL VOLTAGE RATING ITEM (Not applicable to all parts. Refer to Electrical Characteristics Table for additional information) I HOLD HOLD CURRENT CODE (Refer to Electrical Characteristics Table) L: LITTELFUSE SURFACE MOUNT PPTC DEVICE SIZE CODE (0.20 x 0.16 inch) Packaging Part Number Ordering Number Halogen Free I hold (A) I hold Code 2016L030 2016L050 2016L075/060 2016L100 2016L100/33 2016L150 2016L150/33 2016L200 2016L260/24 2016L300/16 2016L500 2016L030DR 2016L050MR 2016L075/60MR 2016L100PR 2016L100/33DR 2016L150DR 2016L150/33DR 2016L200PR 2016L260/24DR 2016L300/16MR 2016L500DR Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 0.30 0.55 0.75 1.10 1.10 1.50 1.50 2.00 2.60 3.00 5.00 030 050 075 110 110 150 150 200 260 300 500 Voltage Option /60 /33 /33 /24 /16 /6 Packaging Option Quantity Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel 1500 1000 1000 2000 1500 1500 1,500 2000 1,500 1,000 1,500 Quantity & Packaging Codes DR MR MR PR DR DR DR PR DR MR DR (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/22/17 POLY-FUSE(R) Resettable PTCs Surface Mount > 2016L Series Tape and Reel Specifications TAPE SPECIFICATIONS: EIA-481-1 (mm) 2016L030 2016L100/33 2016L150 2016L100 2016L150/33 2016L050 2016L200 2016L260/24 2016L075/60 2016L300/16 2016L500 W 12.0+/- 0.30 12.0+/- 0.30 12.0+/- 0.30 REEL DIMENSIONS: EIA-481-1 (mm) C O178.0+/-1.0 F 5.50+/- 0.05 5.50+/- 0.05 5.50+/- 0.05 D O60.2+/-0.5 E1 1.75+/- 0.10 1.75+/- 0.10 1.75+/- 0.10 H 16.0+/- 0.5 W 13.2+/- 1.5 D0 1.55+/- 0.05 1.55+/- 0.05 1.55+/- 0.05 D1 1.50 (MIN) 1.50 (MIN) 1.50 (MIN) P0 4.0+/- 0.10 4.0+/- 0.10 4.0+/- 0.10 P1 8.0+/- 0.10 8.0+/- 0.10 8.0+/- 0.10 P2 2.0+/- 0.05 2.0+/- 0.05 2.0+/- 0.05 A0 4.40+/- 0.10 4.48+/- 0.10 4.45+/- 0.10 B0 5.50+/- 0.10 5.40+/- 0.10 5.48+/- 0.10 T 0.25+/- 0.10 0.25+/- 0.10 0.25+/- 0.10 KO 0.80+/- 0.10 1.36+/- 0.10 1.86+/- 0.10 Leader Min. 390 390 390 Trailer Min. 160 160 160 Tape and Reel Diagram H D0 P0 P1 E1 P2 D F W T D1 D1 K0 W B0 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/22/17 C