2455R01000072 - HONEYWELL - Datasheet.Live

POLY-FUSE® Resettable PTCs

Speciﬁcations are subject to change without notice.

Revised: 03/22/17

Surface Mount > 2016L Series

The 2016L Series PTC provides surface mount overcurrent

protection for low voltage (≤60V) applications where

resettable protection is desired.

Electrical Characteristics

Part Number Marking I hold

(A)

I trip

(A)

V max

(Vdc)

I max

(A)

P d typ.

(W)

Maximum Time

To Trip Resistance Agency

Approvals

Current

(A)

Time

(Sec.)

R min

(Ω)

R 1max

(Ω)

2016L030 LF030 0.30 0.60 60 20 1.40 1. 5 3.0 0.500 2.300 X X

2016L050 LF050 0.55 1. 10 60 20 1.40 2.5 5.0 0.200 1.000 X X

2016L075/60 LF075 0.75 1.50 60 20 1.40 8.0 0.5 0.130 0.900 X X

2016L100 LF100 1. 10 2.20 15 40 1.40 8.0 0.5 0.100 0.400 X X

2016L100/33 LF100-33 1. 10 2.20 33 40 1.40 8.0 0.5 0.100 0.400 X X

2016L150 LF150 1.50 3.00 15 40 1.40 8.0 1. 0 0.070 0.180 X X

2016L150/33 LF150-33 1.50 3.00 33 40 2.0 8.00 1. 0 0 0.070 0.180 X X

2016L200 LF200 2.00 4.20 6 40 1.40 8.0 3.0 0.048 0.100 X X

2016L260/24 LF260-24 2.60 5.00 24 40 1. 6 8.00 5.00 0.025 0.075 X X

2016L300/16 LF0300 3.00 5.00 16 40 1. 6 8.00 10.00 0.015 0.048 X X

2016L500 LF500 5.00 10.00 6 10 0 2.0 25.00 2.00 0.005 0.025 X X

I hold = Hold current: maximum current device will pass without tripping in 20°C still air.

I trip = Trip current: minimum current at which the device will trip in 20°C still air.

V max = Maximum voltage device can withstand without damage at rated current (I max)

I max = Maximum fault current device can withstand without damage at rated voltage (Vmax)

P d = Power dissipated from device when in the tripped state at 20°C still air.

R min = Minimum resistance of device in initial (un-soldered) state.

R typ = Typical resistance of device in initial (un-soldered) state.

R 1max = Maximum resistance of device at 20°C measured one hour after tripping or reﬂow soldering of 260°C for 20 sec.

Caution: Operation beyond the speciﬁed rating may result in damage and possible arcing and ﬂame.

* Agency Approval is Pending

Description

Features

Applications

• RoHS compliant, lead-free

and halogen-free

• Fast response to fault

currents

• High voltage

• Low-proﬁle

• IEEE 1394 port protection

• Powered ethernet port

protection (IEEE 802.3 af)

• Automotive electronic

control module protection

• Low voltage telecom

equipment protection

Agency Approvals

2016L Series RoHS

WARNING

• Users shall independently assess the suitability of these devices for each of their applications

• Operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or ﬁre

• These devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such

conditions are expected to be repetitive or prolonged in duration

• Exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these PPTC devices

• These devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses

• Circuits with inductance may generate a voltage (L di/dt) above the rated voltage of the PPTC device.

AGENCY AGENCY FILE NUMBER

E183209

R50119118

POLY-FUSE® Resettable PTCs

Speciﬁcations are subject to change without notice.

Revised: 03/22/17

Surface Mount > 2016L Series

Ambient Operation Temperature

-40°C -20°C 0°C 20°C 40°C 50°C 60°C 70°C 85°C

Part Number Hold Current (A)

2016L030 0.45 0.40 0.35 0.30 0.25 0.23 0.20 0.18 0.14

2016L050 0.93 0.80 0.65 0.50 0.42 0.38 0.33 0.30 0.23

2016L075/60 1.21 1.06 0.91 0.75 0.61 0.54 0.45 0.38 0.26

2016L100 1.66 1.47 1.29 1. 10 0.91 0.83 0.73 0.64 0.50

2016L100/33 1.66 1.47 1.29 1. 10 0.91 0.83 0.73 0.64 0.50

2016L150 2.26 2.00 1. 76 1.50 1.24 1. 13 1. 0 0 0.87 0.68

2016L150/33 2.25 2.05 1.79 1.50 1.31 1. 17 1.05 0.93 0.72

2016L200 2.80 2.50 2.19 2.00 1.84 1. 74 1.50 1.34 1. 14

2016L260/24 3.80 3.43 3.04 2.60 2.24 2.03 1.82 1.64 1.25

2016L300/16 4.32 3.93 3.57 3.00 2.58 2.40 2.22 1.89 1.68

2016L500 7.20 6.55 5.95 5.00 4.30 4.00 3.70 3.15 2.80

Temperature Rerating

Temperature Rerating Curve

Average Time Current Curves

The average time current curves and Temperature Rerating curve performance is affected

by a number or variables, and these curves provided as guidance only. Customer must

verify the performance in their application.

Note:

Typical Temperature rerating curve, refer to table for derating data

-40 -30 -20 -10010 20 30 40 50 60 70 80 85

10%

30%

50%

70%

90%

110%

130%

150%

170%

Temperature (°C)

Percentage of Rated Current

0.01

0.1

100

0.1

Time in Seconds

Current in Amperes

0.30A

0.50A

0.75A/60

1. 00A

1. 00A/33

1.50A

2.00A

1.50A/33

2.60A/24

3.00A/16

5.00A

Additional Information

Datasheet Samples

Resources Samples

POLY-FUSE® Resettable PTCs

Speciﬁcations are subject to change without notice.

Revised: 03/22/17

Surface Mount > 2016L Series

Environmental Speciﬁcations

Soldering Parameters

Operating/Storage

Temperature -40°C to +85°C

Maximum Device Surface

Temperature in Tripped

State

125°C

Passive Aging +85°C, 1000 hours

-/+5% typical resistance change

Humidity Aging +85°C, 85%,R.H.,1000 hours

-/+5% typical resistance change

Thermal Shock

MIL–STD–202, Method 107

+85°C/-40°C 20 times

-30% typical resistance change

Solvent Resistance MIL–STD–202, Method 215

No change

Vibration

MIL–STD–883, Method 2007,

Condition A

No change

Moisture Sensitivity Level Level 1, J–STD–020

Physical Speciﬁcations

Terminal Material Solder-Plated Copper (Solder Material:

Matte Tin(Sn))

Lead Solderability Meets EIA Speciﬁcation RS186-9E, ANSI/

J-STD-002 Category 3.

Time

Temperature

TS(max)

TS(min)

time to peak temperature

Preheat

reheat

Ramp-up

amp-up

Ramp-down

amp-d

Critical Zone

tL to tP

Proﬁle Feature Pb-Free Assembly

Average Ramp-Up Rate (TS(max) to TP) 3°C/second max

Pre Heat:

Temperature Min (Ts(min))150°C

Temperature Max (Ts(max))200°C

Time (Min to Max) (ts)60 – 180 secs

Time Maintained

Above:

Temperature (TL)217°C

Temperature (tL)60 – 150 seconds

Peak / Classiﬁcation Temperature (TP) 260+0/-5 °C

Time within 5°C of actual peak

Temperature (tp)20 – 40 seconds

Ramp-down Rate 6°C/second max

Time 25°C to peak Temperature (TP) 8 minutes Max.

-- All temperature refer to topside of the package, measured on the package body surface

-- If reﬂow temperature exceeds the recommended proﬁle, devices may not meet the

performance requirements

-- Recommended reﬂow methods: IR, vapor phase oven, hot air oven, N2 environment

for lead

-- Recommended maximum paste thickness is 0.25mm (0.010 inch)

-- Devices can be cleaned using standard industry methods and solvents

-- Devices can be reworked using the standard industry practices

POLY-FUSE® Resettable PTCs

Speciﬁcations are subject to change without notice.

Revised: 03/22/17

Surface Mount > 2016L Series

Part Ordering Number System

PACKAGING STYLE

L: LITTELFUSE SURFACE MOUNT PPTC

QUANTITY CODE: D=1500 M=1000 P=2000

R: Tape & Reel

2016 L xxx /xx D R

SERIES

DEVICE SIZE CODE (0.20 x 0.16 inch)

I HOLD HOLD CURRENT CODE

(Refer to Electrical Characteristics Table)

SPECIAL VOLTAGE RATING ITEM

(Not applicable to all parts. Refer to Electrical

Characteristics Table for additional information)

-A: Automotive grade

Blank: Standard version

- A

Packaging

Dimensions (mm)

Top

View

Pad

Layout

Side

View

Bottom

View

4.60 mm

(.181”)

3.40 mm

(.133”)

1.50 mm

(.059”)

MARKING CODE VARIES

WITH AMPERAGE AND VOLTAGE RATING

SEE ELECTRICAL CHARACTERISTICS CHART

SHOWN ARE:

- 1.1A/15V RATING (LEFT)

- 1.1A/33V RATING (RIGHT)

100

-33

Part

Number

A B C D E

Inches mm Inches mm Inches mm Inches mm Inches mm

Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max Min Max

2016L030

0.19 0.21 4.72 5.44 0.15 0.17 3.7

4.43

0.03 0.05 0.75 1.25

0.01 0.06 0.3 1. 5 0.01 0.03 0.25 0.65

2016L050 0.05 0.08 1.20 2.00

2016L075/60 0.05 0.08 1.20 2.00

2016L100 0.02 0.03 0.50 0.75

2016L100/33 0.03 0.05 0.75 1.25

2016L150 0.03 0.06 0.75 1.55

2016L150/33 4.43 0.03 0.06 0.80 1.60

2016L200 4.43 0.02 0.03 0.50 0.75

2016L260/24

4.43 0.03 0.06 0.80 1.602016L300/16

2016L500

Part Number Ordering Number Halogen

Free

I hold

(A) I hold Code Voltage

Option

Packaging

Option Quantity Quantity &

Packaging Codes

2016L030 2016L030DR Ye s 0.30 030 Tape and Reel 1500 DR

2016L050 2016L050MR Ye s 0.55 050 Tape and Reel 1000 MR

2016L075/060 2016L075/60MR Ye s 0.75 075 /60 Tape and Reel 1000 MR

2016L100 2016L100PR Ye s 1. 10 110 Tape and Reel 2000 PR

2016L100/33 2016L100/33DR Ye s 1. 10 110 /33 Tape and Reel 1500 DR

2016L150 2016L150DR Ye s 1.50 150 Tape and Reel 1500 DR

2016L150/33 2016L150/33DR Ye s 1.50 150 /33 Tape and Reel 1,500 DR

2016L200 2016L200PR Ye s 2.00 200 Tape and Reel 2000 PR

2016L260/24 2016L260/24DR Ye s 2.60 260 /24 Tape and Reel 1,500 DR

2016L300/16 2016L300/16MR Ye s 3.00 300 /16 Tape and Reel 1,000 MR

2016L500 2016L500DR Ye s 5.00 500 /6 Tape and Reel 1,500 DR

POLY-FUSE® Resettable PTCs

Speciﬁcations are subject to change without notice.

Revised: 03/22/17

Surface Mount > 2016L Series

TAPE SPECIFICATIONS: EIA-481-1 (mm)

REEL DIMENSIONS:

EIA-481-1 (mm)

2016L100

2016L200

2016L030

2016L100/33

2016L150

2016L150/33

2016L260/24

2016L300/16

2016L500

2016L050

2016L075/60

W12.0+/- 0.30 12.0+/- 0.30 12.0+/- 0.30 CØ178.0+/-1.0

F5.50+/- 0.05 5.50+/- 0.05 5.50+/- 0.05 DØ60.2+/-0.5

E11.75+/- 0.10 1.75+/- 0.10 1.75+/- 0.10 H16.0+/- 0.5

D01.55+/- 0.05 1.55+/- 0.05 1.55+/- 0.05 W13.2+/- 1.5

D11.50 (MIN) 1.50 (MIN) 1.50 (MIN)

P04.0+/- 0.10 4.0+/- 0.10 4.0+/- 0.10

P18.0+/- 0.10 8.0+/- 0.10 8.0+/- 0.10

P22.0+/- 0.05 2.0+/- 0.05 2.0+/- 0.05

A04.40+/- 0.10 4.48+/- 0.10 4.45+/- 0.10

B05.50+/- 0.10 5.40+/- 0.10 5.48+/- 0.10

T0.25+/- 0.10 0.25+/- 0.10 0.25+/- 0.10

KO0.80+/- 0.10 1.36+/- 0.10 1.86+/- 0.10

Leader Min. 390 390 390

Trailer Min. 160 160 160

Tape and Reel Speciﬁcations

Tape and Reel Diagram

K0B0

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and

test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.

Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics.