Product Specification 108-60034 AMP Connector USB Consortium, Plug & Receptacle Lead Free Version 1. Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality requirements of AMP* Universal Serial Bus(USB) consortium plug and receptacle connectors. These connectors are mounted plug and printed circuit board mounted receptacle connectors. 1.2 Qualification: When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. Applicable Documents The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and referenced documents, this specification shall take precedence. 2.1 AMP Specifications: A. 109-1: General Requirements for Test Specifications B. 109 Series : Test Specifications as indicated in Figure 1. (Comply with MIL-STD-202, MIL-STD-1344 and EIA RS-364) C. Corporate Bulletin 401-76: Cross-reference between AMP Test Specifications and Government or Commercial Documents D. 114-40054: Application Specification. E. 501-60007: Qualification Test Report DR DIST O LTR RELEASED FB00-0155-04 C.W REVISION RECORD ASHL-0004-ES REV A DR 20JUN 04 DATE C. WANG CHK S. YAO APP I. ENOMOTO PAGE 1 of 7 Tyco Electronics AMP Shanghai Ltd NO 108-60034 REV O LOC ES TITLE AMP Connector, USB Consortium, Plug & Receptacle Lead Free Version 3. Requirements: 3.1 Design and Construction: Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2 Materials: A. Contact: (1) Plug: Copper alloy: gold over palladium nickel plating on contact area, tin plating on solder area, all over nickel plating or gold plating on contact area, tin plating on solder area, all over nickel plating (2) Receptacle: Copper alloy: gold over palladium nickel plating on contact area, tin plating on solder area, all over nickel plating or gold plating on contact area, tin plating on solder area, all over nickel plating B. Housing: Plug : Thermoplastic, black, 130 C, UL94V-0 Receptacle: Thermoplastic, black, 130 C, UL94V-0 Plug: Steel ,bright tin over copper Receptacle: Copper alloy , bright tin C. Shell: 3.3 3.4 Ratings: A. Voltage Rating : 30 vac (rms) B. Current Rating : Signal application only,1 ampere maximum per contact C. Temperature Rating: -55C to +85C unless limited by cable or overmold Performance Requirements and Test Descriptions: The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.1. Unless otherwise specified all tests shall be performed at ambient environmental conditions per AMP Specification 109-1 Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 2 108-60034 REV LOC O ES 3.5 Para. 3.5.1 Test Requirements and Procedures Summary: Test Items Examination of Product Requirements Procedures Meets requirements of product drawing and AMP Spec 114-40054. Visually, dimensionally and functionally inspected per applicable inspection plan Electrical Requirements 3.5.2 Termination Resistance 3.5.3 Insulation Resistance 1000 M Min. AMP Spec 109-28-4 Test between the adjacent contacts of mating and unmating samples 3.5.4 Dielectric Withstanding voltage 750 vac at sea level 1 minute hold with no breakdown or flashover AMP Spec 109-29-1 Test between the adjacent contacts of mating and unmating samples 3.5.5 Capacitance 2 picofarads maximum AMP Spec 109-47 Test between the adjacent contacts of unmating samples at 1KHZ 3.5.6 Vibration Random Mechanical Requirements No electrical discontinuities greater than 1 microsecond shall occur. See Note 3.5.7 Physical Shock No electrical discontinuity greater than 1 microsecond shall occur. See Note 3.5.8 Mating Force 35 N maximum Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A AMP Spec 109-6-6 Subject mated contact assembled in housing to 20 mv maximum open circuit at 100 ma maximum See figure 3 R=10 m Max. AMP Spec 109-21-5 Subject mated connectors to 5.35 G's rms .15 minutes in each of 3 mutually perpendicular planes See Figure 4 AMP Spec 109-26-1 Except 30 G's Subject mated connectors to 30 G's half-sine shock pulses of 11 millisecond duration; 3 shocks in each direction applied along the 3 mutually perpendicular planes, total 18 shocks; See figure 4 AMP Spec 109-42 Condition A Measure force necessary to mate samples at maximum rate of 12.5 mm a minute. PAGE NO 3 108-60034 REV LOC O ES Para. 3.5.9 Test Items Unmating Force Requirements 10 N minimum Procedures AMP Spec 109-42 Condition A Measure force necessary to unmate samples at maximum rate of 12.5 mm per minute. 3.5.10 Cable Retention Force Cable shall not dislodge from crimp AMP Spec 109-46 Apply axial load 25 N to cable 3.5.11 Durability See Note AMP Spec 109-27 Mate and unmate samples for 1500 cycles at maximum rate of 200 cycles per hour 3.5.12 Solder ability Solderable area shall have minimum of 95%solder coverage AMP Spec 109-11-1 Subject surface mount samples to Solder ability. AMP Spec 109-11-1 Subject through hole samples to Solder ability. Environmental Requirements 3.5.13 Thermal Shock See Note AMP Spec 109-22 Subject mated samples to 25 cycles between -55 oC and +85 oC. 3.5.14 Temperature life See Note AMP Spec 109-43 Subject mated samples to temperature life at 85 oC for 315 hours 3.5.15 Humidity-Temperature Cycling See Note AMP Spec 109-23-3 Condition B Subject samples to 10 ,24 hours cycles between 25 oC and 65 oC at 95% R.H. 3.5.16 Mixed flowing Gas See Note AMP Spec 109-85-2 Subject mated samples to Environmental class for 14 days. NOTE Shall meet visual requirement, show no physical damage and shall meet requirement of additional tests as specified in Test Sequence in Figure 2. Figure 1 (end) Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 4 108-60034 REV LOC O ES 3.6 Product Qualification and Requalification Test Sequence Test Group(a) Test of Examination 1 2 3 4 5 Test Sequence (b) Examination of Product 1, 10 1, 5 1, 5 Termination Resistance 3,7 2.4 2.4 1, 9 Insulation Resistance 3, 7 Dielectric Withstanding Voltage 4, 8 Capacitance 2 2 Solder ability Vibration 5 Physical Shock 6 Durability 4 Mating Force 2 Unmating force 8 Cable Retention 9 Thermal Shock 5 Humidity-Temperature Cycling 6 Temperature Life 3(c) 3(c) Mixed flowing gas NOTE 1, 3 (a) See Para 4.1.A. (b) Numbers indicate sequence in which tests are performed (b) Precondition samples with 10 cycles durability Figure 2 4 4.1 QUALITY ASSURANCE PROVISIONS Qualification Testing A. Sample Selection Sample shall be prepared in accordance with applicable Instruction Sheet and shall be selected at random from current production Test group 1,2,3and 4 shall each consist of minimum of 8 connectors. Test group 5 shall consist of a minimum of 8 printed circuit board receptacles Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 5 108-60034 REV LOC O ES connectors. A minimum of 30 contacts shall be selected and identified for each test group. Unless otherwise specified, these contacts shall be used for all measurements. B. Test Sequence Qualification inspection shall be verified testing samples as specified in Figure 2. 4.2 Requalification Testing If changes significantly affecting form, fit or function is made to be product or manufacturing process, product assurance shall coordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering. 4.3 Acceptance Acceptance is based on verification that the product meets requirement of Figure 1.Failures attributed to equipment, test setup or operator deficiencies shall not disqualify the product. When product failure occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm corrective action is required before resubmitted. 4.4 Quality Conformance Inspection Applicable AMP quality inspection plan will specify the sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with the applicable product drawing and this specification. Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 6 108-60034 REV LOC O ES V X SERIAL BUS PLUG P.C.BOARD CABLE POINT OF WIRE TERMINATION CONTACT TAIL SERIAL BUS RECEPTACLE A Figure 3 Termination Resistance Measurement Point DISCONTINUITY MONITOR A UPPER CLAMP P.C.BOARD SERIAL BUS PLUG CABLE SERIAL BUS RECEPTACLE VIBRATION/SHOCK TABLE Figure 4 Vibration & Physical Shock Mounting Fixture Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 7 108-60034 REV LOC O ES