Item-No.: SPECIFICATION T60404-M4645-X601 V AC U UM SC H M ELZE K-No.: 25152 Date: 6-15-25A Current-Sensor-Module 02.10.2007 For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Customer: Standard Type Cutomers Part No.: Page 1 of 3 Description Characteristics Applications * Closed loop (compensation) Current Sensor with magnetic field probe * Printed circuit board mounting * Casing and materials UL-listed * Excellent accuracy * Very low offset current * Very low temperature dependency and offset current drift * Very low hysteresis of offset current * Short response time * Wide frequency bandwidth * Compact design Mainly used for stationary operation in industrial applications: * AC variabel speed drives and servo motor drives * Static converters for for DC motor drives * Battery supplied applications * Switched Mode Power Supplies (SMPS) * Power Supplies for welding applications * Uninterruptable Power Supplies (UPS) Electrical Data - Ratings IPN RM ISN KN Primary rated current, r.m.s Load resistance Output rated current, r.m.s Turns ratio Accuracy - Dynamic performance data (with DRV401 @ VC = 5V 5%) IP,max Max. measuring range @ RM = 12,5 X(T) Measuring accuracy @ IPN, TA= -40... +85C L Linearity I0(T) Offset current @ IP=0, TA= -40... +85C I0H Hysteresis tr Response time t(Ip,max) Delay time at di/dt = 100 A/s f Frequency range General Data TA TS m RS RP Ck min. 85 typ 0.02 0.02 0.3 0.2 DC...100 min. typ. 25 0 ... 200 12.5 1...3 : 2000 A mA max. Unit A % % mA mA s s kHz Unit 0.5 0.1 0.05 0.05 max. Ambient temperature -40 +85 C Storage temperature -40 +90 C Mass 12 g Secondary coil resistance @ TA=85C 67 Primary coil resistance per turn @ TA=25C 1 m Coupling capacity 5 pF Mechanical Stress according to M3209/3 10g Settings: 10 - 2000 Hz, 1 min/Decade, 2 hours Constructed and manufactored and tested in accordance with EN 61800-5-1 (Pin 1 - 6 to Pin 7 - 10) Reinforced insulation, Insulation material group 3a, Pollution degree 2 clearance (component without solder pad) 7 mm creepage (component without solder pad) 7 mm System voltage overvoltage category 3 RMS 300 V Working voltage (table 7 acc. to EN61800-5-1) RMS 350 V Rated discharge voltage peak value 1040 V sclear screep Vsys Vwork UPD Type Testing according EN 61800-5-1 (Pin 1 - 6 to Pin 7 - 10) VW Vd Ve Datum Hrsg.: HV transient test according to M3064 (1,2 s / 50 s-wave form) Testing voltage to M3014 (5 s) Partial discharge voltage acc.M3024 (RMS) with Vvor (RMS) Name KB-E Index 81 6 3 1100 1375 kV kV V V Anderung Bearb: SA KB-E: Le KB-PM: KRe. freig.: Heu. released designer check check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten editor Item-No.: SPECIFICATION T60404-M4645-X601 V AC U UM SC H M ELZE K-No.: 25152 Date: 6-15-25A Current-Sensor-Module 02.10.2007 For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Customer: Standard Type Cutomers Part No.: Mechanical outline (mm): Page 4 Toleranz der Stiftabstande 0,2 mm (Tolerances grid distance) 7 14 12,7 of 3 Connections: 1...6: 1 mm 7..10: 0,46*0,46 mm General tolerances DIN ISO 2768-c 6 2 10 1 22,2 3 6,24 4,1 10 Marking: F 24 DC 1,1 15,1 4645X601 F DC 0,5 3,50,5 O1,0 1,84 2,14 1,905 7,62 12 2,54 0,46x0,46 5,72 DC = Date Code F = Factory Schematic diagram NS ip + i iS 1...3 10 9 + Sensor Winding } Compensation Winding 8 NK 4...6 } Pin 10 : S2 Pin 9 : S1 Pin 8 : K2 Pin 7 : K1 7 Inspection (Measurements after temperature balance of the samples at room temperature.) KN (N1/N2) I0 (K1-K2) (S1-S2) RS (K1-K2) R (S1-S2) Vd (V) (V) (V) (V) (V) (V) M3011/6c: M3226: M3090: M3090: M3011/5: M3011/5: M3014: Turns ratio (IP=3*8A, 40...80 Hz) Offset current Magnetic Flux compensation core Magnetic Flux sensor Winding resistance compensation coil Winding resistance magnetic probe coil Testing voltage, rms, 1s M3024: Partial discharge voltage (RMS) with Vvor (RMS) 3 : 2000 0,5 < 0.05 4.5...7 20...35 44...52,5 2.3...3.0 1,5 % mA nVs nVs kV >1100 1375 V V Pin 1 - 6 to Pin 7 - 10 Ve (AQL1/S4) Applicable documents Current direction: A positive output current appears at point IS, by primary current in direction of the arrow. Temperature of the primary conductor should not exceed 110C Housing and bobbin material: UL-listed. Flammability class UL 94V-0. Enclosures according to IEC 60529: IP50. Additional data available on request. This specification is no declaration of warranty acc. BGB 443. Hrsg.: KB-E Bearb: SA KB-E: Le KB-PM: KRe. freig.: Heu. released designer check check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten editor Item-No.: SPECIFICATION T60404-M4645-X601 V AC U UM SC H M ELZE K-No.: 25152 Date: 6-15-25A Current-Sensor-Module 02.10.2007 For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Customer: Standard Type Cutomers Part No.: Page 3 of 3 Explanation of several of the terms used in the tablets (in alphabetical order) I0H: Zero variation of Io after overloading with a DC of tenfold the rated value (RM = RMN) I0t: Long term drift of Io after 100 temperature cycles in the range -40 bis 85 C. tr: Response time (describe the dynamic performance for the specified measurement range), measured as delay time at IP = 0,9 . IPmax between a rectangular current and the output current. t (IPmax): Delay time (describe the dynamic performance for the rapid current pulse rate e.g short circuit current) measured between IPmax and the output current ia with a primary current rise of di1/dt = 100 A/s. UPD Rated discharge voltage (recurring peak voltage separated by the insulation) proved with a sinusoidal voltage Ve UPD = 2 * Ve / 1,5 Vvor Defined voltage is the RMS valve of a sinusoidal voltage with peak value of 1,875 * UPD required for partial discharge test in IEC 61800-5-1 Vvor = 1,875 *UPD / 2 Vsys System voltage RMS value of rated voltage according to IEC 61800-5-1 Vwork Working voltage voltage according to IEC 61800-5-1 which occurs by design in a circuit or across insulation Xges(IPN): The sum of all possible errors over the temperature range by measuring a current IPN: I S (I PN ) -1 K N I PN X ges = 100 X: % Permissible measurement error in the final inspection at RT, defined by X = 100 ISB - 1 % ISN where ISB is the output DC value of an input DC current of the same magnitude as the (positive) rated current (Io = 0 ) XTi: Temperature drift of the rated value orientated output term. ISN (cf. Notes on Fi) in a specified temperature range, obtained by: X Ti = 100 L: I SB (TA2 ) - I SB (TA1 ) I SN Linearity fault defined by L = 100 % IP I - Sx I PN ISN % Where IP is any input DC and ISx the corresponding output term. ISN: see notes of Fi (Io = 0). This "Additional information" is no declaration of warranty according BGB $443. Hrsg.: KB-E Bearb: SA KB-E: Le KB-PM: KRe. freig.: Heu. released designer check check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten editor