VACUUMSCHMELZE
SPECIFICATION
Item-No.:
T60404-M4645-X601
K-No.:
25152 6-15-25A Current-Sensor-Module
Date:
02.10.2007
Customer:
Standard Type Cutomers Part No.: Page 1 of 3
Hrsg.: KB-E
editor Bearb:
designer
SA KB-E: Le
check KB-PM: KRe.
check freig.: Heu.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
For the electronic measurement of currents:
DC, AC, pulsed, mixed ..., with a galvanic
Isolation between the primary circuit
(high power) and the secondary circuit
Description
• Closed loop (compensation)
Current Sensor with magnetic
field probe
• Printed circuit board mounting
• Casing and materials UL-listed
Characteristics
• Excellent accuracy
• Very low offset current
• Very low temperature dependency and offset
current drift
• Very low hysteresis of offset current
• Short response time
• Wide frequency bandwidth
• Compact design
Applications
Mainly used for stationary operation in industrial
applications:
• AC variabel speed drives and servo motor
drives
• Static converters for for DC motor drives
• Battery supplied applications
• Switched Mode Power Supplies (SMPS)
• Power Supplies for welding applications
• Uninterruptable Power Supplies (UPS)
Electrical Data – Ratings
IPN Primary rated current, r.m.s 25 A
R
M
Load resistance 0 ... 200 Ω
ISN Output rated current, r.m.s 12.5 mA
K
N
Turns ratio 1…3 : 2000
Accuracy – Dynamic performance data (with DRV401 @ VC = 5V ±5%) min. typ max. Unit
I
P,max Max. measuring range @ RM = 12,5 Ω ±85 A
X(T) Measuring accuracy @ IPN, TA= -40… +85°C 0.5 %
ε
L
Linearity 0.1 %
I
0
(T) Offset current @ IP=0, TA= -40… +85°C 0.02 0.05 mA
I0H Hysteresis 0.02 0.05 mA
t
r
Response time 0.3 µs
∆t(Ip,max) Delay time at di/dt = 100 A/µs 0.2 µs
f Frequency range DC...100 kHz
General Data min. typ. max. Unit
T
A
Ambient temperature -40 +85 °C
T
S
Storage temperature -40 +90 °C
m Mass 12 g
R
S
Secondary coil resistance @ TA=85°C 67 Ω
RP Primary coil resistance per turn @ TA=25°C 1 mΩ
C
k
Coupling capacity 5 pF
Mechanical Stress according to M3209/3 10g
Settings: 10 – 2000 Hz, 1 min/Decade, 2 hours
Constructed and manufactored and tested in accordance with EN 61800-5-1 (Pin 1 - 6 to Pin 7 – 10)
Reinforced insulation, Insulation material group 3a, Pollution degree 2
sclear clearance (component without solder pad) 7 mm
s
creep creepage (component without solder pad) 7 mm
Vsys System voltage overvoltage category 3 RMS 300 V
V
work Working voltage (table 7 acc. to EN61800-5-1) RMS 350 V
UPD Rated discharge voltage peak value 1040 V
Type Testing according EN 61800-5-1 (Pin 1 - 6 to Pin 7 - 10)
VW HV transient test according to M3064 (1,2 µs / 50 µs-wave form) 6 kV
V
d
Testing voltage to M3014 (5 s) 3 kV
V
e
Partial discharge voltage acc.M3024 (RMS) 1100 V
with Vvor (RMS) 1375 V
Datum Name Index Änderung
81
VACUUMSCHMELZE
SPECIFICATION
Item-No.:
T60404-M4645-X601
K-No.:
25152 6-15-25A Current-Sensor-Module
Date:
02.10.2007
Customer:
Standard Type Cutomers Part No.: Page 2 of 3
Hrsg.: KB-E
editor Bearb:
designer
SA KB-E: Le
check KB-PM: KRe.
check freig.: Heu.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
For the electronic measurement of currents:
DC, AC, pulsed, mixed ..., with a galvanic
Isolation between the primary circuit
(high power) and the secondary circuit
Mechanical outline (mm): General tolerances DIN ISO 2768-c
Toleranz der Stiftabstände
±0,2 mm
(Tolerances grid distance)
DC = Date Code
F = Factory
F DC
22,2
6,24
24
15,1
0,5
4,1
1,1
7,62
12
1,84
2,54
12,7
2,14
1,905 5,72
Ø1,0
0,46x0,46
≤14
3,5±0,5
10
7
64
3
1
10
Schematic diagram
Inspection (Measurements after temperature balance of the samples at room temperature.)
KN (N1/N2) (V) M3011/6c: Turns ratio (IP=3*8A, 40…80 Hz) 3 : 2000 ± 0,5 %
I
0
M3226: Offset current < 0.05 mA
∆Φ (K1-K2) (V) M3090: Magnetic Flux compensation core 4.5...7 nVs
∆Φ (S1-S2) (V) M3090: Magnetic Flux sensor 20...35 nVs
R
S (K1-K2) (V) M3011/5: Winding resistance compensation coil 44...52,5 Ω
R (S1-S2) (V) M3011/5: Winding resistance magnetic probe coil 2.3...3.0 Ω
V
d
(V) M3014: Testing voltage, rms, 1s 1,5 kV
Pin 1 - 6 to Pin 7 – 10
V
e
(AQL1/S4) M3024: Partial discharge voltage (RMS) >1100 V
with Vvor (RMS) 1375 V
Applicable documents
Current direction: A positive output current appears at point IS, by primary current in direction of the arrow.
Temperature of the primary conductor should not exceed 110°C
Housing and bobbin material: UL-listed. Flammability class UL 94V-0.
Enclosures according to IEC 60529: IP50.
Additional data available on request.
This specification is no declaration of warranty acc. BGB §443.
i
p
+
8
7
}
i
+
10
9
Pin 10 : S2
Pin 9 : S1
}
Pin 8 : K2
Pin 7 : K1
Sensor Winding
Compensation Winding
i
S
1...3
4...6
N
S
N
K
Connections:
1...6: ∅ 1 mm
7..10: 0,46*0,46 mm
4645X601
F DC
Marking:
VACUUMSCHMELZE
SPECIFICATION
Item-No.:
T60404-M4645-X601
K-No.:
25152 6-15-25A Current-Sensor-Module
Date:
02.10.2007
Customer:
Standard Type Cutomers Part No.: Page 3 of 3
Hrsg.: KB-E
editor Bearb:
designer
SA KB-E: Le
check KB-PM: KRe.
check freig.: Heu.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
For the electronic measurement of currents:
DC, AC, pulsed, mixed ..., with a galvanic
Isolation between the primary circuit
(high power) and the secondary circuit
Explanation of several of the terms used in the tablets (in alphabetical order)
I0H: Zero variation of Io after overloading with a DC of tenfold the rated value (RM = RMN)
I0t: Long term drift of Io after 100 temperature cycles in the range -40 bis 85 °C.
tr: Response time (describe the dynamic performance for the specified measurement range), measured as delay time
at IP = 0,9 . IPmax between a rectangular current and the output current.
∆t (IPmax): Delay time (describe the dynamic performance for the rapid current pulse rate e.g short circuit current)
measured between IPmax and the output current ia with a primary current rise of di1/dt = 100 A/µs.
UPD Rated discharge voltage (recurring peak voltage separated by the insulation) proved with a sinusoidal voltage Ve
UPD = √2 * Ve / 1,5
V
vor Defined voltage is the RMS valve of a sinusoidal voltage with peak value of 1,875 * UPD required for partial discharge
test in IEC 61800-5-1
V
vor = 1,875 *UPD / √2
V
sys System voltage RMS value of rated voltage according to IEC 61800-5-1
V
work Working voltage voltage according to IEC 61800-5-1 which occurs by design in a circuit or across insulation
Xges(IPN): The sum of all possible errors over the temperature range by measuring a current IPN:
(
)
1
IK
II
100X
PNN
PNS
ges −
⋅
⋅= %
X: Permissible measurement error in the final inspection at RT, defined by
1
I
I
100X SN
SB −⋅= %
where ISB is the output DC value of an input DC current of the same magnitude as the (positive) rated current (Io = 0 )
X
Ti: Temperature drift of the rated value orientated output term. ISN (cf. Notes on Fi) in a specified temperature range,
obtained by:
(
)
(
)
SN
A1SBA2SB
Ti I
TITI
100 −
⋅=X%
εL: Linearity fault defined by
SN
Sx
PN
P
LI
I
II
100 −⋅=ε%
Where IP is any input DC and ISx the corresponding output term. ISN: see notes of Fi (Io = 0).
This “Additional information“ is no declaration of warranty according BGB $443.
