GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS DESCRIPTION The 4N29, 4N30, 4N31, 4N32, 4N33 have a gallium arsenide infrared emitter optically coupled to a silicon planar photodarlington. 4N29 4N30 4N31 4N32 4N33 FEATURES * High sensitivity to low input drive current * Meets or exceeds all JEDEC Registered Specifications * VDE 0884 approval available as a test option -add option .300. (e.g., 4N29.300) SCHEMATIC ANODE 1 6 BASE APPLICATIONS * * * * * Low power logic circuits Telecommunications equipment Portable electronics Solid state relays Interfacing coupling systems of different potentials and impedances. ABSOLUTE MAXIMUM RATINGS CATHODE 2 5 COLLECTOR N/C 3 4 EMITTER (TA = 25C Unless otherwise specified.) Parameter Symbol Value Units TSTG -55 to +150 C Operating Temperature TOPR -55 to +100 C Lead Solder Temperature TSOL 260 for 10 sec C 250 mW 3.3 mW/C IF 80 mA VR 3 V TOTAL DEVICE Storage Temperature Total Device Power Dissipation @ TA = 25C Derate above 25C EMITTER Continuous Forward Current Reverse Voltage Forward Current - Peak (300 s, 2% Duty Cycle) PD 3.0 A 150 mW 2.0 mW/C BVCEO 30 V Collector-Base Breakdown Voltage BVCBO 30 V Emitter-Collector Breakdown Voltage BVECO LED Power Dissipation @ TA = 25C Derate above 25C DETECTOR Collector-Emitter Breakdown Voltage Detector Power Dissipation @ TA = 25C Derate above 25C Continuous Collector Current IF(pk) PD PD IC 5 V 150 mW 2.0 mW/C 150 mA 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS 4N29 ELECTRICAL CHARACTERISTICS 4N30 4N31 4N32 4N33 (TA = 25C Unless otherwise specified.) INDIVIDUAL COMPONENT CHARACTERISTICS Parameter Test Conditions EMITTER V V (VR = 3.0 V) IR 0.001 100 A (VF = 0 V, f = 1.0 MHz) C 150 *Collector-Base Breakdown Voltage (IC = 100 A, IE = 0) *Emitter-Collector Breakdown Voltage (IE = 100 A, IB = 0) DC Current Gain Unit 1.5 BVCEO *Collector-Emitter Dark Current Max 1.2 (IC = 100 A, IB = 0) *Collector-Emitter Breakdown Voltage Typ VF *Reverse Leakage Current DETECTOR Min (IF = 10 mA) *Input Forward Voltage *Capacitance Symbol pF 30 60 BVCBO 30 100 V BVECO 5.0 8 V (VCE = 10 V, Base Open) ICEO 1 (VCE = 5.0 V, IC = 500 A) hFE 5000 100 nA Max Units TRANSFER CHARACTERISTICS DC Characteristic Test Conditions Symbol *Collector Output Current(1,2) (4N32, 4N33) Min Typ 50 (500) (4N29, 4N30) (IF = 10 mA, VCE = 10 V, IB = 0) IC (CTR) (4N31) 10 (100) mA (%) 5 (50) *Saturation Voltage(2) (4N29, 4N30, 4N32, 4N33) (4N31) (IF = 8.0 mA, IC = 2.0 mA) 1.0 VCE(sat) 1.2 V TRANSFER CHARACTERISTICS AC Characteristic Turn-on Test Conditions Time(3) Turn-off Time(3) (4N32, 4N33) (IF = 200 mA, IC = 50 mA, VCC = 10 V) (Fig.7) (4N29, 4N30, 4N31) Symbol Min Typ Units 5.0 ton 100 toff Bandwidth(4,5) Max s 40 BW 30 KHz ISOLATION CHARACTERISTICS Characteristic Test Conditions Input-Output Isolation Voltage(6) (4N29, 4N30, 4N31, 4N32, 4N33) Isolation Resistance(6) Isolation Capacitance(6) Symbol (II-O 61 A, Vrms, t = 1 min.) *(4N32) VDC *(4N33) VDC Min Typ Max 5300 VISO Units Vac(rms) 2500 V 1500 (VI-O = 500 VDC) RISO 1011 1 (VI-O = , f = 1 MHz) CISO 0.8 pf 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS 4N29 TA = 0C, 25C TA = 70C TA = 100C TA = -55C 1 NORMALIZED TO: CTR @ IF = 10 mA TA = 25C VCE = 5 V 0.1 0.1 1 10 100 NORMALIZED TO: CTR @ IF = 10 mA TA = 25C VCE = 10 V 0.1 -80 IF = 10 mA 10 IF = 5 mA 6 IF = 2 mA 2 IF = 1 mA 0 0 1 2 3 4 5 6 7 8 -40 -20 0 20 40 60 80 100 120 Fig. 4 Dark Current vs. Ambient Temperature ICEO - COLLECTOR-EMITTER DARK CURRENT (nA) IC - COLLECTOR CURRENT (NORMALIZED) NORMALIZED TO: IF = 1 mA VCE = 5 V 4 -60 TA - AMBIENT TEMPERATURE (C) 16 8 4N33 1 Fig. 3 Collector Current vs. Collector-Emitter Voltage 12 4N32 10 IF - LED INPUT CURRENT (mA) 14 4N31 Fig. 2 Current Transfer Ratio vs. Ambient Temperature CTR - CURRENT TRANSFER RATIO (NORMALIZED) CTR - CURRENT TRANSFER RATIO (NORMALIZED) Fig. 1 Output Current vs. Input Current 4N30 9 10000 VCE = 10 V 1000 100 10 1 0.1 0.01 10 0 20 40 60 80 100 TA - AMBIENT TEMPERATURE (C) VCE- COLLECTOR -EMITTER VOLTAGE (V) Fig. 5 Turn-On Time vs. Input Current Fig. 6 Turn-Off Time vs. Input Current 1000 1000 RL = 1 k1 VCC = 10 V 100 10 TOFF - TIME (s) TON - TIME (s) RL = 100 1 RL = 10 1 RL = 1 k1 100 RL = 100 1 10 RL = 10 1 1 VCC = 10 V 1 0.1 0.1 1 10 IF - LED INPUT CURRENT (mA) 100 0.1 1 10 100 IF - LED INPUT CURRENT (mA) 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS 4N29 4N30 4N31 4N32 4N33 TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES (25C Free air temperature unless otherwise specified) (Cont.) Test Circuit Waveforms VCC = 10 V INPUT PULSE I C = 50 mA INPUT RL I F = 200 mA INPUT PULSE WIDTH OUTPUT 10% OUTPUT PULSE 90% <1 ms tr ton tf toff Fig. 7 Switching Time Test Circuit and Waveforms Notes * Indicates JEDEC registered data. 1. The current transfer ratio(IC/IF) is the ratio of the detector collector current to the LED input current with VCE @ 10 V. 2. Pulse test: pulse width = 300s, duty cycle 62.0% . 3. For test circuit setup and waveforms, refer to figure 7.. 4. IF adjusted to IC = 2.0 mA and IC = 0.7 mA rms. 5. The frequency at which IC is 3dB down from the 1 KHz value. 6. For this test, LED pins 1 and 2 are common, and phototransistor pins 4,5 and 6 are common. 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS 4N29 Package Dimensions (Through Hole) 4N30 4N31 4N32 4N33 Package Dimensions (Surface Mount) PIN 1 ID. 0.350 (8.89) 0.330 (8.38) 3 2 PIN 1 ID. 1 0.270 (6.86) 0.240 (6.10) SEATING PLANE 0.270 (6.86) 0.240 (6.10) 0.350 (8.89) 0.330 (8.38) 4 5 0.070 (1.78) 0.045 (1.14) 6 0.300 (7.62) TYP 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.115 (2.92) 0.200 (5.08) 0.165 (4.18) 0.016 (0.41) 0.008 (0.20) 0.020 (0.51) MIN 0.154 (3.90) 0.100 (2.54) 0.016 (0.40) 0.008 (0.20) 0.022 (0.56) 0.016 (0.41) 0 to 15 0.020 (0.51) MIN 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.300 (7.62) TYP 0.100 (2.54) TYP 0.016 (0.40) MIN 0.315 (8.00) MIN 0.405 (10.30) MAX Lead Coplanarity : 0.004 (0.10) MAX Package Dimensions (0.4"Lead Spacing) Recommended Pad Layout for Surface Mount Leadform 0.270 (6.86) 0.240 (6.10) 0.070 (1.78) 0.060 (1.52) SEATING PLANE 0.350 (8.89) 0.330 (8.38) 0.415 (10.54) 0.070 (1.78) 0.045 (1.14) 0.100 (2.54) 0.295 (7.49) 0.030 (0.76) 0.200 (5.08) 0.115 (2.92) 0.154 (3.90) 0.100 (2.54) 0.004 (0.10) MIN 0.016 (0.40) 0.008 (0.20) 0 to 15 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.400 (10.16) TYP NOTE All dimensions are in inches (millimeters) Call QT Optoelectronics for more information or the phone number of your nearest distributor. United States 800-533-6786 * France 33 [0] 1.45.18.78.78 * Germany 49 [0] 89/96.30.51 * United Kingdom 44 [0] 1296 394499 * Asia/Pacific 603-7248193 www.qtopto.com 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS 4N29 4N30 4N31 4N32 4N33 ORDERING INFORMATION Order Entry Identifier Option S .S Description Surface Mount Lead Bend SD .SD Surface Mount; Tape and reel W .W 0.4" Lead Spacing 300 .300 VDE 0884 300W .300W VDE 0884, 0.4" Lead Spacing 3S .3S VDE 0884, Surface Mount 3SD .3SD VDE 0884, Surface Mount, Tape & Reel QT Carrier Tape Specifications ("D" Taping Orientation) 12.0 0.1 4.85 0.20 4.0 0.1 0.30 0.05 4.0 0.1 O1.55 0.05 1.75 0.10 7.5 0.1 16.0 0.3 13.2 0.2 9.55 0.20 0.1 MAX 10.30 0.20 O1.6 0.1 User Direction of Feed NOTE All dimensions are in millimeters Call QT Optoelectronics for more information or the phone number of your nearest distributor. United States 800-533-6786 * France 33 [0] 1.45.18.78.78 * Germany 49 [0] 89/96.30.51 * United Kingdom 44 [0] 1296 394499 * Asia/Pacific 603-7248793 www.qtopto.com 4/25/00 200038B GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. (c) 2000 Fairchild Semiconductor Corporation 4/25/00 200038B