ZFV
C-1ZFV
Smart Vision Sensors
ZFV Color Series
Ordering Information
Models
Sensor Heads
Amplifier Units ZFV Color Series
Accessories ZFV Color Series (order separately)
Data Storage Units
Controller Link Unit
Sensor Head Extension Cable
Panel-mounting Adapter
External Lighting
Appearance Type Setting distance Sensing area Model
Narrow View 34 to 49 mm (variable) 5 × 4.6 mm to 9 × 8.3 mm (variable) ZFV-SC10
Standard View 31 to 187 mm (variable) 10 × 9.2 mm to 50 × 46 mm (variable) ZFV-SC50
Wide View 66 to 141 mm (variable) 50 × 46 mm to 90 × 83 mm (variable) ZFV-SC90
Ultra-wide View 114 to 226 mm (variable) 90 × 83 mm to 150 × 138 mm (variable) ZFV-SC150
Appearance Power supply Output type Model
24 VDC
NPN ZFV-CA40
PNP ZFV-CA45
Appearance Power supply Output type Model
24 VDC
NPN ZS-DSU11
PNP ZS-DSU41
Appearance Model
ZS-XCN
Cable length Model
3 m ZFV-XC3B *1
*1. ZFV-XC3BR Robot Cable is also available.
8 m ZFV-XC8B
Appearance
Model ZS-XOM1 ZS-XPM2
First Unit Additional Units
(for expansion)
Type Model
Bar Lighting ZFV-LTL01
Bar Double Lighting ZFV-LTL02
Bar Low-angle Lighting ZFV-LTL04
Light Source for Through-beam Lighting ZFV-LTF01
C-2 Vision Systems
Specifications
Sensor Heads
Item ZFV-SC10
(Narrow View) ZFV-SC50/SC50W
(Standard View) ZFV-SC90/SC90W
(Wide View) ZFV-SC150/SC150W
(Ultra Wide View)
Setting distance (L) 34 to 49 mm (variable) 31 to 187 mm (variable) 67 to 142 mm (variable) 115 to 227 mm (variable)
Detection range (H × V) 5 × 4.6 mm to 9 × 8.3 mm
(variable)
10 × 9.2 mm to 50 × 46 mm
(variable)
50 × 46 mm to 90 × 83 mm
(variable)
90× 83 mm to 150 × 138 mm
(variable)
Relation between setting
distance and
detection range
Built-in lens Focus: f15.65 Focus: f13.47 Focus: f6.1
Object lighting method Pulse lighting
Object light source 8 white LEDs 36 LEDs 20 white LEDs 72 white LEDs
Lightning I/F (Option) None Yes None
Sensing element 1/3-inch CCD
Shutter Electronic shutter, shutter time: 1/500 to 1/8,000
Power supply voltage 15 VDC (Supplied from
Amplifier Unit.)
15 VDC, 48 VDC (Supplied from Amplifier Unit.)
Current consumption Approx. 200 mA Approx. 350 mA [15 V: approx. 150 mA, 48 V: approx. 200 mA]
(Including the current consumed when external light is connected)
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance
(destructive)
10 to 150 Hz, 0.35 mm single amplitude, 10 times each in X, Y, and Z directions for 8 min
Shock resistance
(destructive) 150 m/s2, three times each in six directions (up/down, left/right, forward/backward)
Ambient temperature Operating: 0 to +40 °C, Storage: -25 to +65 °C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% (with no condensation)
Ambient atmosphere Must be free of corrosive gas.
Connection type Prewired, Standard cable length: 2 m
Degree of protection
(IEC 60529)
IP65 ZFV-SC___: IP65
ZFV-SC___W: IP67
Material Case: ABS, Mounting bracket: PBT
Weight Approx. 200 g
(including mounting bracket
and cord; packaged
condition: approx. 300 g)
Approx. 270 g
(including mounting bracket
and cord; packaged
condition: approx. 350 g)
Approx. 300 g
(including mounting bracket
and cord; packaged
condition: approx. 380 g)
Approx. 600 g
(including mounting bracket
and cord; packaged
condition: approx. 780 g)
Accessories Mounting bracket
ZFV-XMF (1),
Ferrite core (1),
Instruction sheet
Mounting bracket
ZFV-XMF2 (1),
Ferrite core (2),
Warning label (1)
Instruction sheet
Mounting bracket
ZFV-XMF2 (1),
Ferrite core (2),
Warning label (1)
Instruction sheet
Ferrite core (2),
Instruction sheet
LED class *1 Class 1 Class 2 Class 2 Class 1
*1. Applicable standards: IEC60825-1: 1993 +A1:1997 +A2:2001, EN60825-1:1994 +A:2002 +A:2001
Detection
range (V)
(H)
Setting distance (L)
49 mm
34 mm
5 mm 9 mm
Detection range(H)
10 mm
187 mm
31 mm
50 mm
Setting distance (L)
Detection range (H)
50 mm
142 mm
67 mm
90 mm
Detection range (H)
90 mm
227 mm
115 mm
150 mm
Detection range (H)
ZFV
C-3ZFV
Amplifier Units
Item ZFV-CA40 ZFV-CA45
Output specifications NPN open collector, 30 VDC 50 mA max.,
residual voltage 1.2 V max.
PNP open collector, 50 mA max.,
residual voltage 1.2 V max.
Input
specifications
ON Short-circuited with 0 V terminal or 1.5 V or less Supply voltage short-circuited or within supply
voltage -1.5 V max.
OFF
Serial I/O USB2.0 1 port, full-speed (12 Mbps) MINI-B
RS-232C 1 port, 115,200 bps max.
Inspection items PATTERN, AREA, HUE (Color), WIDTH, POSITION, COUNT, BRIGHT, CHARA
Teaching area Rectangular, one area
Teaching area size • PATTERN, BRIGHT: Any rectangular area (256 × 256 max.)
• AREA, HUE (Color), WIDTH, POSITION, COUNT, CHARA: Any rectangular area (full screen max.)
Sensing area Full screen
Resolution 468 x 432 (H x V) max.
Bank switching Supported for 8 banks.
Image input interval 13 ms (Standard), 8 ms (1/2 for partial scan), 5 ms (1/4 for partial scan)
Other functions Control output switching: ON for OK / ON for NG, ON delay / OFF delay, One-shot output, "ECO" mode
Output signals (1) Control output (OUTPUT)
(2) Enable output (ENABLE)
(3) Error output (ERROR)
Input signals (1) Sync measurement input (TRIG)/Continuous measurement input (TRIG); switched by menu
(2) Bank selection inputs (BANK1-3)
(3) Workpiece still teaching (TEACH)/ Workpiece moving teaching (TEACH); switched by menu
Sensor head interface Digital interface
Image display 1.8 inch TFT ccolor LCD (Display dots: 557 x 234 pix)
Indicators • Judgment result indicator (OUTPUT, Color: orange)
• Inspection mode indicator (RUN, Color: green)
• Error indicator (ERR, Color: red)
• Ready status indicator (READY, Color: blue)
Operation interface • Cursor keys (up, down, left, right)
• Setting key (SET)
• Escape key (ESC)
• Operating mode switching (slide switch)
• Menu switching (slide switch)
• Teaching/Display switching key (TEACH/VIEW)
• Function keys (A to D 4 input)
Power supply voltage 20.4 to 26.4 VDC (including ripple)
Current consumption 800 mA max. (with Sensor Head connected)
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between leads and Amplifier Unit case
Noise resistance 1 kV, Pulse rise: 5 ns, Pulse width: 50 ns, Burst duration: 15 ms, Cycle: 300 ms
Vibration resistance (destructive)10 to 150 Hz, 0.1 mm single amplitude, 10 times each in X, Y, and Z directions for 8 min
Shock resistance (destructive)150 m/s2, three times each in six directions (up/down, left/right, forward/backward)
Ambient temperature range Operating: 0 to 50 °C
Storage: -25 to 65 °C (with no icing or condensation)
Ambient humidity range Operating and storage: 35% to 85% (with no condensation)
Ambient atmosphere Must be free of corrosive gas.
Degree of protection IEC 60529, IP20
Material Polycarbonate (PC)
Weight Approx. 300 g (including cord; packaged condition: 450 g)
Accessories Ferrite core (1), Instruction sheet, Label (1)
C-4 Vision Systems
External light units (optional)
Item ZFV-LTF01 ZFV-LT01 ZFV-LTL01 ZFV-LTL04
Applicable sensor head ZFV-SC50/SC50W/SC90/SC90W
Lighting method Pulse lighting
Lighting interval Fixed (1.1 to 1.4 ms)
Light source (Qty.) White LEDs
60 20 40 80
Power supply voltage 48 VDC (Supplied from sensor head)
Current consumption Appprox. 160 mA Appprox. 80 mA Appprox. 120 mA Appprox. 210 mA
Dielectric strength 300 VAC, 50/60 Hz for 1 min
Vibration resistance
(destructive)
10 to 150 Hz, 0.35 mm single amplitude, 10 times each in X, Y and Z directions for 8 min
Shock resistance
(destructive) 150 m/s2, 3 times each in six directions (up/down, left/right, forward/backward)
Ambient temperature Operating: 0 to 40 °C Storage: -20 to 65 °C (with no icing or condensation)
Ambient humidity Operating and storage: 35% to 85% RH (with no condensation)
Ambient atmosphere Must be free of corrosive gas
Connection type Prewired, Standard cable length: 2 m
Degree of protection IEC6D529 IP20
Material SPCC SPCC, aluminium
Weight Approx. 500 g (when
packaged: Approx. 550 g)
Approx. 250 g (when
packaged: Approx. 300 g)
Approx. 650 g (when
packaged: Approx. 900 g)
Approx. 900 g (when
packaged: Approx. 1,150 g)
LED class Class 1
Applicable standards IEC6D825-1: 1993 +A1:1997 +A2:2001
EN60825-1: 1994 +A1:2002 +A2:2001
ZFV
C-5ZFV
Dimensions (Units: mm)
20±0.1
Two, M4
Mounting Hole Dimensions
23.30
33.6
32
4.5 4.5
4.54.5
32
Optical axis
5.6
17.900.80
67.90
8.50
18.7 34
30.10
33
Connector
4
6.36
30
30 (6.36)
Focus adjustment dial
34
20
33.6
12.8 dia.
Heat-resistive vinyl-insulated cable
5.8 dia, standard length: 2 m
Two, M4
Depth: 6
1/4-20UNC
Depth: 6
Mounting Bracket can be attached to any side.
Sensor Heads
ZFV-SC10 (Narrow view)
5.6
9.8
8.5
6.2 dia.
Heat-resistive vinyl-insulated cable
6.2 dia, standard length: 2 m
Mounting Bracket can be attached to any side.
3
5
(6.36)
Mounting Hole
Dimensions
86
26.5
8
35.2
35.5
20±0.1
Tw o, M 4
30.1
34
34
26.5
(6.36)
39 52.5
52.5
30.3
Two, M4
Depth: 6
1/4-UNC
Depth: 6
34
38.9
20
ZFV-SC50/SC50W (Standard view)
20
±
0.1
2-M4
30.25
52.5
52.5
39
Mounting hole dimensions
Heat-resistant PVC shielded cable
6.2 Standard length 2 m
20
34
38.9
34
83.7
4
8.5
8.5
7
8.5
35.5
35.5
33
33
5.6
9.8
6.2
33
30.1
A mounting bracket can be
mounted to each side
1/4-20UNC
Depth 6
2-M4
Depth 6
ZFV-SC90/SC90W (Wide view)
C-6 Vision Systems
Amplifier Units
20 ± 0.1
2-M4
140
140
110.2
59.5
8.5
98
57
3512
5
29
8.5 4
8.5
8.5
33
7
73.2
Mounting hole dimensions
Heat-resistant PVC shielded cable
6.2 Standard length 2 m
Mounting surface
ZFV-SC150/SC150W (Ultra wide view)
3.90
4.30
4.61
10.80
1013
52.50
23.2
60
90
32.90
18
24.20
11.7 dia.
ZFV-CA4@
ZFV
C-7ZFV
External light units (optional)
ZFV-LTL01 (bar lighting)
ZFV-LTL02 (bar double-lighting)
37.4
69
69 ± 0.1
74
20
20 ± 0.1
8 ± 0.1
10.7
29
8
14
2000+100
0
62
20
P5.8 × 9 = 52.2
2 × 3-M3 Depth 5
2-M3 Depth 5
Mounting hole dimensions
Mounting hole dimensions
100 ± 0.1
100 ± 0.1
Mounting hole dimensions
59.9
85
85
140
3.233
100 2020
140
100
20 20
165.4
350+35
0
2000+100
0
90°
4-M4 (Thru)
20
62
P5.8 × 9 = 52.2
C-8 Vision Systems
ZFV-LTL04 (bar low-angle lighting)
ZFV-LTF01 (light source for through-beam lighting)
350+35
0
59.9
3.233
90°
140
165.4
100 2020
140
165.4
100
20 20
20
2000+100
0
85
85
62
4-M4(Thru)
P5.8 × 9 = 52.2
100 ± 0.1
100 ± 0.1
Mounting hole dimensions
74 ± 0.1
74 ± 0.1
Mounting hole dimensions
74
74
22
2000+100
0
103 1
70
109
4-M3 Depth 8
70
(Emitting surface)
(Emitting surface)
ZFV
C-9ZFV
About the I/O cable
The following shows the leads that comprise the I/O cable.
(1) Power Supply
This connects the power supply.
Use a DC power supply with safe extra-low-voltage circuits to prevent high voltage.
Wire the power supply separately from other devices. Wiring them together or placing them in the same duct may cause induction, resulting
in malfunction or damage.
(2) GND
The GND terminal is the 0 V power supply terminal.
(3) OUTPUT (control output)
This outputs judgment results. This lead is interlocked with OUTPUT LED.
(4) ENABLE (enable output)
This turns ON when error is generated. This leads is interlocked with ERR LED.
(5) ERROR (error output)
This turns ON when an error is generated. This lead is interlocked with ERR LED.
(6) TEACH (teching output)
There are two teaching modes, workpiece stop teaching and workpiece move teaching. These teaching modes can be selected in the menu.
(7) TRIG (measurement trigger input)
There are two measurement modes, synchronus measurement and continuos measurement. Which mode of measurement is to be per-
formed in is selected in the menu.
(8) BANK1 (bank swichting input 1)
(9) BANK2 (bank swichting input 2)
(10) BANK3 (bank swichting input 3)
The bank No. can be switched when the BANK1 to BANK3 are connected as follows
.
Bank No. BANK1 BANK2 BANK3
BANK1 OFF OFF OFF
BANK2 ON OFF OFF
BANK3 OFF ON OFF
BANK4 ON ON OFF
BANK5 OFF OFF ON
BANK6 ON OFF ON
BANK7 OFF ON ON
BANK8 ON ON ON
(1) Power supply
(3) OUTPUT*
(4) ENABLE
(5) ERROR
(6) TEACH*
(7) TRIG*
(8) BANK1*
(9) BANK2*
(10) BANK3*
(2) GND
Brown
Blue
Black
Orange
Light blue
Ye l lo w
Pink
Gray
Green
Red
* : Enabled only in the RUN mode
Purple
White
Unused
Unused
C-10 Vision Systems
I/O Circuit diagrams
NPN output type (ZFV-CA40)
PNP output type (ZFV-CA45)
Brown
Blue
Black
Orange
Light blue
Load
Load
Load
Power supply (24VDC)
24VDC
Yellow
Pink
Gray
Green
Red
OUTPUT
ENABLE
ERROR
GND(0V)
TEACH
TRIG
BANK1
BANK2
BANK3
Internal circuits
Brown
Blue
Black
Orange
Light blue
Load
Power supply (24VDC)
OUTPUT
ENABLE
ERROR
GND(0V)
24VDC
Yellow
Pink
Gray
Green
TEACH
TRIG
BANK1
BANK2
Red BANK3
Load
Load
Internal circuits
ZFV
C-11ZFV
Timing Charts
The following shows the timing charts when communication is performed with external devices.
Measurement
Continuos measurement
Measurement is performed continuosly for the duration that the TRIG signal is ON.
The measurement result is updated and output to external deveices at each measurement cycle.
Synchronuos measurement
Measurement is performed only once in synchrnous with the change in TRIG signal state from OFF to ON and the result is output.
• The minimum ON time width of the TRIG signal is 1 ms.
• The OUTPUT signal is helad until the measurement result is updated.
Note:However, when one-shot is set, the OUTPUT signal is held for the preset time.
Tout
TRIG
OUTPUT
ENABLE
OFF
ON
OFF
ON
OFF
ON
Tout: Measurement cycle
The measurement cycle changes
depending on the setting.
Tout
TRIG
OUTPUT
ENABLE
OFF
ON
OFF
ON
OFF
ON
Tout: Measurement time.
The measurement time changes
depending on the setting.
C-12 Vision Systems
Teaching
Workpiece stop teaching
Teaching processing is performed according to TRIG signal input after the TEACH signal input.
Measurement is not performed while teaching is being performed. Do not move the workpiece until teaching is completed.
(1) Turn the TEACH signal ON.
(2) Confirm that the ENABLE signal has turned OFF.
(3) Make sure that the workpiece to be taught is in the teaching area.
(4) Input the TRIG signal.
(5) The ENABLE signal turns ON after teaching is completed. At this timing, check the state of the ERROR signal.
(6) When teaching has been completed successfully, the ERROR signal stays OFF.
(7) When teaching fails, the ERROR signal turns ON.
(8) Turn the TEACH signal OFF and end teaching processing.
When teaching fails, the state before teaching was initiated is returned to. Performe teaching again.
If the TEACH signal is turned OFF midway, teaching is disabled.
Workpiece move teaching
Use this teaching mode when the object cannot be stopped. Teaching processing is divided up and performed in synchronous with the
TRIG signal input after the TEACH signal is input.
Teaching must be processewd eight times. Measurement is not performed while teaching is being performed.
(1) Turn the TEACH signal ON from the outside.
(2) Confirm that the ENABLE signal has turned OFF.
(3) Input the TRIG signal at the timing for measuring the workpiece to be taught.
(4) Repeat the input in step (3) eight times. (Trigger inputs from the ninth time onwars are ignored.)
(5) The ENABLE signal turns ON after teaching is completed. Check the state of the ERROR signal at this timing.
(6) When teaching has been completed successfully, the ERROR signal stays OFF.
(7) When teaching fails, the ERROR signal turns ON.
(8) Turn the TEACH signal OFF and end teaching processing.
When teaching fails, the state before teaching was initiated is return to. Perform teaching again.
If the TEACH signal is turned OFF midway, teaching is disabled.
During teaching processing
TRIG OFF
ON
TEACH OFF
ON
ENABLE OFF
ON
ERROR OFF
ON
(1)
(2)
(4)
(5)
(7)
(6)
(8)
During teaching processing
Min.150ms
TEACH OFF
ON (1) (8)
ERROR OFF
ON (6)
(7)
ENABLE OFF
ON (2) (5)
TRIG OFF
ON (3) (4)
In the interest of product improvement, specifications are subject to change without notice.Cat. No. E373-E2-01-X
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://oeweb.omron.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
2052121/,1(
*OREDOKWWSZZZRPURQFRP
86$KWWSZZZRPURQFRPRHL
&DQDGDKWWSZZZRPURQFD
Cat. No. E373-E2-01 8/06 Specifications subject to change without notice Printed in USA
20521&$1$'$,1&
0LOQHU$YHQXH
7RURQWR2QWDULR0%9
20521(/(&7521,&6//&
2QH&RPPHUFH'ULYH
6FKDXPEXUJ,/
)RU86WHFKQLFDOVXSSRUWRURWKHULQTXLULHV
&RPSOHWH¦7HUPVDQG&RQGLWLRQVRI6DOH§IRUSURGXFWSXUFKDVHDQGXVHDUHRQ2PURQ©VZHEVLWH
DWZZZRPURQFRPRHL¤XQGHUWKH¦$ERXW8V§WDELQWKH/HJDO0DWWHUVVHFWLRQ
$//',0(16,2166+2:1$5(,10,//,0(7(56
7RFRQYHUWPLOOLPHWHUVLQWRLQFKHVPXOWLSO\E\7RFRQYHUWJUDPVLQWRRXQFHVPXOWLSO\E\
