MC10EL34, MC100EL34 5V ECL P2, P4, P8 Clock Generation Chip Description The MC10/100EL34 is a low skew /2, /4, /8 clock generation chip designed explicitly for low skew clock generation applications. The internal dividers are synchronous to each other, therefore, the common output edges are all precisely aligned. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. The common enable (EN) is synchronous so that the internal dividers will only be enabled/disabled when the internal clock is already in the LOW state. This avoids any chance of generating a runt clock pulse on the internal clock when the device is enabled/disabled as can happen with an asynchronous control. An internal runt pulse could lead to losing synchronization between the internal divider stages. The internal enable flip-flop is clocked on the falling edge of the input clock, therefore, all associated specification limits are referenced to the negative edge of the clock input. Upon startup, the internal flip-flops will attain a random state; the master reset (MR) input allows for the synchronization of the internal dividers, as well as multiple EL34s in a system. The 100 Series contains temperature compensation. www.onsemi.com 16 1 SOIC-16 D SUFFIX CASE 751B-05 MARKING DIAGRAMS* 16 10EL34G AWLYWW 1 16 100EL34G AWLYWW Features * * * * * * * 50 ps Output-to-Output Skew Synchronous Enable/Disable Master Reset for Synchronization PECL Mode Operating Range: VCC = 4.2 V to 5.7 V with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = -4.2 V to -5.7 V Internal Input 75 kW Pulldown Resistors on CLK(s), EN, and MR These Devices are Pb-Free, Halogen Free and are RoHS Compliant 1 A WL YY WW G *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION Device (c) Semiconductor Components Industries, LLC, 2016 July, 2016 - Rev. 11 1 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package Package Shipping MC10EL34DG SOIC-16 Pb-Free) 48 Units/Tube MC100EL34DG SOIC-16 (Pb-Free) 48 Units/Tube Publication Order Number: MC10EL34/D MC10EL34, MC100EL34 VCC EN NC CLK 16 15 14 D Q 13 CLK VBB 12 MR VEE 10 9 11 Table 1. FUNCTION TABLE R /2 Q R /4 Q R Q /8 2 3 4 5 6 7 8 Q0 Q0 VCC Q1 Q1 VCC Q2 Q2 EN* MR* Function Z ZZ X L H X L L H Divide Hold Q0-3 Reset Q0-3 *Pins will default low when left open. Z = Low-to-High Transition ZZ = High-to-Low Transition R 1 CLK* Table 2. PIN DESCRIPTION Pin *All VCC pins are tied together on the die. Warning: All VCC and VEE pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. Logic Diagram and Pinout Assignment Function CLK, CLK ECL Diff Clock Inputs EN ECL Sync Enable MR ECL Master Reset Q0, Q0 ECL Diff /2 Outputs Q1, Q1 ECL Diff /4 Outputs Q2, Q2 ECL Diff /8 Outputs VBB Reference Voltage Output VCC Positive Supply VEE Negative Supply NC No Connect Table 3. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 KW Internal Input Pullup Resistor N/A ESD Protection Human Body Model Machine Model Charge Device Model > 1 KV > 100 V > 2 KV Moisture Sensitivity (Note 1) Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Transistor Count 191 Devices Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional Moisture Sensitivity information, refer to Application Note AND8003/D. www.onsemi.com 2 MC10EL34, MC100EL34 Table 4. MAXIMUM RATINGS Symbol Rating Unit VCC PECL Mode Power Supply Parameter VEE = 0 V Condition 1 Condition 2 8 V VEE NECL Mode Power Supply VCC = 0 V -8 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 -6 V Iout Output Current Continuous Surge 50 100 mA IBB VBB Sink/Source 0.5 mA TA Operating Temperature Range -40 to +85 C Tstg Storage Temperature Range -65 to +150 C qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm SOIC-16 130 75 C/W qJC Thermal Resistance (Junction-to-Case) Standard Board SOIC-16 33 to 36 C/W Tsol Wave Solder (Pb-Free) <2 to 3 sec @ 260C 265 C VI VCC VI VEE Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 5. 10EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0 V (Note 1)) -40C Symbol Characteristic 25C Min Typ Max 85C Min Typ Max Typ Max Unit IEE Power Supply Current 39 mA VOH Output HIGH Voltage (Note 2) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mV VOL Output LOW Voltage (Note 2) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mV VIH Input HIGH Voltage (Single-Ended) 3770 4110 3870 4190 3940 4280 mV VIL Input LOW Voltage (Single-Ended) 3050 3500 3050 3520 3050 3555 mV VBB Output Voltage Reference 3.57 3.7 3.65 3.75 3.69 3.81 V Input HIGH Voltage Common Mode Range (Differential) (Note 3) 3.0 4.6 3.0 4.6 3.0 4.6 V 150 mA VIHCMR IIH Input HIGH Current IIL Input LOW Current 39 Min 39 150 0.5 150 0.5 0.3 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.06 V / -0.5 V. 2. Outputs are terminated through a 50 W resistor to VCC - 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. www.onsemi.com 3 MC10EL34, MC100EL34 Table 6. 10EL SERIES NECL DC CHARACTERISTICS (VCC = 0 V; VEE = -5.0 V (Note 1)) -40C Symbol Characteristic Min Typ 25C Max Min 85C Typ Max Typ Unit 39 mA Power Supply Current VOH Output HIGH Voltage (Note 2) -1080 -990 -890 -980 -895 -810 -910 -815 -720 mV VOL Output LOW Voltage (Note 2) -1950 -1800 -1650 -1950 -1790 -1630 -1950 -1773 -1595 mV VIH Input HIGH Voltage (Single-Ended) -1230 -890 -1130 -810 -1060 -720 mV VIL Input LOW Voltage (Single-Ended) -1950 -1500 -1950 -1480 -1950 -1445 mV VBB Output Voltage Reference -1.43 -1.30 -1.35 -1.25 -1.31 -1.19 V Input HIGH Voltage Common Mode Range (Differential) (Note 3) -2.0 -0.4 -2.0 -0.4 -2.0 -0.4 V 150 mA IIH Input HIGH Current IIL Input LOW Current 39 Max IEE VIHCMR 39 Min 150 0.5 150 0.5 0.3 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.06 V / -0.5 V. 2. Outputs are terminated through a 50W resistor to VCC - 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 7. 100EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0 V (Note 1)) -40C Symbol Characteristic Min Typ 25C Max Min Typ Max Min Typ Unit 42 mA Power Supply Current VOH Output HIGH Voltage (Note 2) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mV VOL Output LOW Voltage (Note 2) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mV VIH Input HIGH Voltage (Single-Ended) 3835 4120 3835 4120 3835 4120 mV VIL Input LOW Voltage (Single-Ended) 3190 3525 3190 3525 3190 3525 mV VBB Output Voltage Reference 3.62 3.74 3.62 3.74 3.62 3.74 V Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) 2.2 4.6 2.2 4.6 2.2 4.6 V 150 mA IIH Input HIGH Current IIL Input LOW Current 39 Max IEE VIHCMR 39 85C 150 0.5 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / -0.5 V. 2. Outputs are terminated through a 50W resistor to VCC - 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. www.onsemi.com 4 MC10EL34, MC100EL34 Table 8. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0 V; VEE = -5.0 V (Note 1)) -40C Symbol Characteristic Min Typ 25C Max Min Typ Max Min Typ Unit 42 mA Power Supply Current VOH Output HIGH Voltage (Note 2) -1085 -1005 -880 -1025 -955 -880 -1025 -955 -880 mV VOL Output LOW Voltage (Note 2) -1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 mV VIH Input HIGH Voltage (Single-Ended) -1165 -880 -1165 -880 -1165 -880 mV VIL Input LOW Voltage (Single-Ended) -1810 -1475 -1810 -1475 -1810 -1475 mV VBB Output Voltage Reference -1.38 -1.26 -1.38 -1.26 -1.38 -1.26 V Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) -2.8 -0.4 -2.8 -0.4 -2.8 -0.4 V 150 mA IIH Input HIGH Current IIL Input LOW Current 39 Max IEE VIHCMR 39 85C 150 150 0.5 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / -0.5 V. 2. Outputs are terminated through a 50W resistor to VCC - 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 9. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = -5.0 V (Note 1)) -40C Characteristic Min fmax Maximum Toggle Frequency 1.1 tPLH tPHL Propagation CLK to Q0 Delay to CLK to Q1,2 Output MR to Q Symbol Typ 25C Max Min Typ 85C Max 1.1 Min Typ Max 1.1 Unit GHz 960 1200 960 1200 970 1210 900 1140 900 1140 910 1150 750 1060 750 1060 790 1090 ps tSKEW Within-Device Skew (Note 2) 100 100 100 ps tJITTER Cycle-to-Cycle Jitter 1.0 1.0 1.0 ps tS Setup Time EN 400 400 400 ps tH Hold Time EN 250 250 250 ps tRR Set/Reset Recovery 400 VPP Input Swing (Note 3) 150 1000 150 1000 150 1000 mV Output Rise/Fall Times Q (20% - 80%) 225 475 225 475 225 475 ps tr tf 200 400 200 400 200 ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. 10 Series: VEE can vary +0.06 V / -0.5 V. 100 Series: VEE can vary +0.8 V / -0.5 V. 2. Within-device skew is defined as identical transitions on similar paths through a device. 3. VPPmin is minimum input swing for which AC parameters guaranteed. The device has a DC gain of 40. www.onsemi.com 5 MC10EL34, MC100EL34 There are two distinct functional relationships between the Master Reset and Clock: Internal Clock Disabled Internal Clock Enabled MR CLK Q0 Q1 Q2 EN CASE 1: If the MR is De-asserted (H-L), While the Clock is Still High, the Outputs will Follow the First Ensuing Clock Rising Edge. Internal Clock Disabled Internal Clock Enabled MR CLK Q0 Q1 Q2 EN CASE 2: If the MR is De-asserted (H-L), After the Clock has Transitioned Low, the Outputs will Follow the Second Ensuing Clock Rising Edge. Figure 2. Timing Diagrams The EN signal will "freeze" the internal divider flip-flops on the first falling edge of CLK after its assertion. The internal divider flip-flops will maintain their state during the freeze. The EN is deasserted (LOW), and after the next falling edge of CLK, then the internal divider flip-flops will "unfreeze" and continue to their next state count with proper phase relationships. TRR TRR CLOCK CLOCK MR MR OUTPUT OUTPUT CASE 1 CASE 2 Figure 3. Reset Recovery Time www.onsemi.com 6 MC10EL34, MC100EL34 Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC - 2.0 V Figure 4. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D - Termination of ECL Logic Devices.) Resource Reference of Application Notes AN1405/D - ECL Clock Distribution Techniques AN1406/D - Designing with PECL (ECL at +5.0 V) AN1503/D - ECLinPSt I/O SPiCE Modeling Kit AN1504/D - Metastability and the ECLinPS Family AN1568/D - Interfacing Between LVDS and ECL AN1672/D - The ECL Translator Guide AND8001/D - Odd Number Counters Design AND8002/D - Marking and Date Codes AND8020/D - Termination of ECL Logic Devices AND8066/D - Interfacing with ECLinPS AND8090/D - AC Characteristics of ECL Devices www.onsemi.com 7 MC10EL34, MC100EL34 PACKAGE DIMENSIONS SOIC-16 CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S DIM A B C D F G J K M P R G R K F X 45 _ C -T- SEATING PLANE J M D MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 16 PL 0.25 (0.010) M T B S A S STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. COLLECTOR BASE EMITTER NO CONNECTION EMITTER BASE COLLECTOR COLLECTOR BASE EMITTER NO CONNECTION EMITTER BASE COLLECTOR EMITTER COLLECTOR STYLE 2: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. CATHODE ANODE NO CONNECTION CATHODE CATHODE NO CONNECTION ANODE CATHODE CATHODE ANODE NO CONNECTION CATHODE CATHODE NO CONNECTION ANODE CATHODE STYLE 3: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. COLLECTOR, DYE #1 BASE, #1 EMITTER, #1 COLLECTOR, #1 COLLECTOR, #2 BASE, #2 EMITTER, #2 COLLECTOR, #2 COLLECTOR, #3 BASE, #3 EMITTER, #3 COLLECTOR, #3 COLLECTOR, #4 BASE, #4 EMITTER, #4 COLLECTOR, #4 STYLE 5: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. DRAIN, DYE #1 DRAIN, #1 DRAIN, #2 DRAIN, #2 DRAIN, #3 DRAIN, #3 DRAIN, #4 DRAIN, #4 GATE, #4 SOURCE, #4 GATE, #3 SOURCE, #3 GATE, #2 SOURCE, #2 GATE, #1 SOURCE, #1 STYLE 6: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE ANODE ANODE ANODE ANODE ANODE ANODE ANODE ANODE STYLE 7: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. SOURCE NCH COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) GATE PCH COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) SOURCE PCH SOURCE PCH COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) GATE NCH COMMON DRAIN (OUTPUT) COMMON DRAIN (OUTPUT) SOURCE NCH STYLE 4: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. SOLDERING FOOTPRINT COLLECTOR, DYE #1 COLLECTOR, #1 COLLECTOR, #2 COLLECTOR, #2 COLLECTOR, #3 COLLECTOR, #3 COLLECTOR, #4 COLLECTOR, #4 BASE, #4 16X EMITTER, #4 0.58 BASE, #3 EMITTER, #3 BASE, #2 EMITTER, #2 BASE, #1 EMITTER, #1 www.onsemi.com 8 8X 6.40 16X 1 1.12 16 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MC10EL34, MC100EL34 ECLinPS is a registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EL34/D