Specifications and information are subject to change without notice
TriQuint Semiconductor, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6633 • e-mail: info-sales@tqs.com • Web site: www. TriQuint.com May 2009
WJZ3030
Broadband Surface Mount Mixer
Product Features
• +20 dBm Input IP3
• RF: 10 – 500 MHz
• LO: 10 – 500 MHz
• IF: 10 – 500 MHz
• +7 dBm LO Drive Level
• No Internal Solder Connections
• Lead Free/RoHS-compliant
SMT package
• No External Bias Required
Applications
• Up/down frequency conversion
• Phase Detector
• Image Rejection
• Current Controlled Attenuator
Product Description
The WJZ3030 is a passive double-balanced diode-ring
mixer that provides high dynamic range performance in a
Lead Free/ RoHS-compliant surface mount package. The
mixer is nominally driven with a LO input power of +7
dBm to optimize its performance. Other WJZ models are
available for other LO drive levels.
Targeted applications include frequency up/down
conversion, modulation and demodulation for receivers and
transmitters used in VHF TV, GSM/ISM. The device can
also be used in Radar, Satellite, Test / Medical Instruments,
Avionics communications and Navigation markets.
Functional Diagram
Top View
Specifications
Parameter Units Min Typ Max Notes
SSB Conversion Loss
RF/LO = 10-500 MHz, IF = 30 MHz dB 6.8 8.3 See note 1
Port-to-Port Isolation
L-R = 10-500 MHz dB 45 60
L-I = 10-500 MHz dB 32 43
R-I = 10-500 MHz dB 36
3rd Order Input Intercept Point dBm +20.0 1MHz tone spacing, See note 1
1dB Input Compression Point dBm TBD
VSWR
RF Port = 10-1000 MHz 1.3:1 IF = 100 MHz
LO Port = 40-1000 MHz 2.7:1
IF Port 1.1:1
LO Drive Level dBm +7
1. Measured in a 50 ohm system with a nominal LO drive of +7 dBm, low side LO, in a downconversion application. With LO = 900MHz, RF=1000MHz, IF=100MHz.
Absolute Maximum Rating
Parameter Rating
Operating Case Temperature -40 to +85 °C
Storage Temperature -65 to +100 °C
RF Input Power +10 dBm
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No. Description
WJZ3030 Broadband Surface Mount Mixer
Standard T/R reel size = 500 pieces on a TBD reel.
1 2 3
6 54
RF
LO
IF
Specifications and information are subject to change without notice
TriQuint Semiconductor, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6633 • e-mail: info-sales@tqs.com • Web site: www. TriQuint.com May 2009
WJZ3030
Broadband Surface Mount Mixer
Performance Charts
Input IP 3 vs Fre quency
IF = 30 MHz, LO = 7 dBm, +25 0C
0
5
10
15
20
25
0 100 200 300 400 500
RF Frequency (MHz)
Input IP3 (dBm)
Conversion Loss vs Frequency
IF = 30 M Hz , LO = 7 dBm, +25 0C
5
6
7
8
9
10
0 100 200 300 400 500
RF Frequency (MHz)
Conversion Loss (dB)
LO VSWR vs Frequency
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
0 100 200 300 400 500
Frequency (MHz)
VSWR
RF VSWR vs Frequency
IF = 30 M Hz , LO = 7 dBm +25 0C
1
1.2
1.4
1.6
1.8
2
0 100 200 300 400 500
Frequency (MHz)
VSWR
Isolation vs LO Frequency
IF = 30 M Hz , LO = 7 dBm , +25 0C
0
15
30
45
60
75
90
0 100 200 300 400 500
LO Frequency (MHz)
Isolation (dB)
L-R L-I R-I
Specifications and information are subject to change without notice
TriQuint Semiconductor, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6633 • e-mail: info-sales@tqs.com • Web site: www. TriQuint.com May 2009
WJZ3030
Broadband Surface Mount Mixer
Mechanical Information
This package is lead-free/RoHS-compliant. The plating material is ENIG “ Electroless Nickel Immersion Gold”
It is compatible with leaded and lead-free (maximum 260°C reflow temperatures)
Also recommend adding active flux of 2% during solder reflow.
Outline Drawing
Land Pattern / Mounting Configuration
Notes:
1. Package unit weight is TBD grams max.
2. Dimensions are expressed in inches.
Dimensions in brackets are millimeter
equivalents.
3. Tolerance .XXX +/- .015, .XX +/- . 02
4. Package circuit board material: ceramic, .025”
total thickness.
5. Blocking capacitors are required on the ports
(pins 1, 4, 5) if any dc signal is present.
Product Marking
The component will be marked with a
“WJZ3030” designator followed by an
alphanumeric lot code on the top surface of the
package.
Tape and reel specifications for this part will be
located on the website in the “Application
Notes” section.
Functional Pin Layout
Pin No. Function
1 LO
4 RF
5 IF
2,3,6 GND
1 2 3
6 5 4
Top View Side View Bottom View
Inches(mm)