RoHS Compliant Value Added ATA Disk Module Specifications for Standard ADM (40P/90D) September 5th, 2013 Version 1.7 Apacer Technology Inc. 1F, No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City, Taiwan, R.O.C Tel: +886-2-2267-8000 www.apacer.com Fax: +886-2-2267-2261 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX Features: Standard ATA/IDE Bus Interface - ATA command set compatible - ATA operating mode supports up to: PIO Mode-4 Multiword DMA Mode-2 Ultra DMA Mode-4 Temperature ranges - Operating: Standard: 0C to 70C Extended: -40C to 85C - Storage: -40C to 100C Connector type - 40-pin female connector Flash management - Advanced wear-leveling algorithms - S.M.A.R.T. technology - Built-in hardware ECC - Flash block management - Power failure management - ATA Security Erase Power consumption (typical)* - Supply voltage: 3.3V & 5V - Active mode: 85mA/95mA (3.3V/5V) - Sleep mode: 500A /600A (3.3V/5V) Performance* - Sustained read: Up to 21 MB/sec - Sustained write: Up to 15 MB/sec Form factor - ATA Disk Module (40-pin/90-degree ) Capacity - 128, 256, 512 MB - 1, 2, 4, 8, 16 GB Shock & Vibration** - Shock: 1,500 G - Vibration: 15 G Pin20 blocked/unblocked by options NAND flash type: SLC RoHS compliant Endurance (TBW: Terabytes Written) - 128 MB: 3.5 TBW - 256 MB: 6.9 TBW - 512 MB: 14.0 TBW - 1 GB: 27.4 TBW - 2 GB: 45.5 TBW - 4 GB: 54.7 TBW - 8 GB: 80.6 TBW - 16 GB: 129.8 TBW *Performance and power consumption may vary from flash configurations or host system settings. **Non-operating 1 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX Table of Contents 1. GENERAL DESCRIPTION .................................................................................................... 3 2. FUNCTIONAL BLOCK .......................................................................................................... 3 3. PIN ASSIGNMENTS ............................................................................................................... 4 4. PRODUCT SPECIFICATIONS.............................................................................................. 5 4.1 CAPACITY .............................................................................................................................................................5 4.2 PERFORMANCE .....................................................................................................................................................5 4.3 ENVIRONMENTAL SPECIFICATION.........................................................................................................................6 4.4 ENDURANCE ........................................................................................................................................................6 5. FLASH MANAGEMENT ........................................................................................................ 7 5.1. ADVANCED WEAR-LEVELING ALGORITHMS .........................................................................................................7 5.2 S.M.A.R.T. TECHNOLOGY ....................................................................................................................................7 5.3 BUILT-IN HARDWARE ECC ...................................................................................................................................7 5.4 FLASH BLOCK MANAGEMENT ...............................................................................................................................7 5.5 POWER FAILURE MANAGEMENT...........................................................................................................................7 5.6 ATA SECURITY ERASE .........................................................................................................................................8 6. SOFTWARE INTERFACE .................................................................................................... 9 6.1 COMMAND SET .....................................................................................................................................................9 7. ELECTRICAL SPECIFICATION ...................................................................................... 11 8. PHYSICAL CHARACTERISTICS ..................................................................................... 12 8.1 DIMENSION .........................................................................................................................................................12 8.1.1 40 pin/ 90 degree Pin 20 blocked ..............................................................................................................12 8.1.2 40 pin/ 90 degree Pin 20 unblocked ..........................................................................................................13 9. PRODUCT ORDERING INFORMATION ........................................................................ 14 9.1 PRODUCT CODE DESIGNATIONS .........................................................................................................................14 9.2 VALID COMBINATIONS .......................................................................................................................................15 2 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 1. General Description Apacer's ATA-Disk Module (ADM) is a high-performance, embedded flash drive designed to replace the conventional PATA (ATA/IDE) hard disk drive. The ADMs can be plugged into a standard parallel ATA connector commonly found in desktops, IT-STB, industrial PCs and thin client systems. Apacer's ADM SSD has a built-in microcontroller with file management firmware that communicates with the ATA standard interfaces. No additional or proprietary host software is required. The ADM is well suited for embedded flash storage applications by offering new and expanded functionalities as well as more cost-effective designs, better performance and increased reliability. The ATA DOM is designed to work at either 5 or 3.3 Volts, supports the standard PATA (ATA/IDE) protocol for up to PIO Mode-4, Multiword DMA Mode-2 and Ultra DMA Mode-4 interfaces, and uses the standard ATA driver complying with most major operating systems. Featuring technologies as Advanced Wear-leveling algorithms, S.M.A.R.T, flash block management, power failure management, and ATA Secure Erase, Apacer's ADM assures users of a versatile device on data storage. 2. Functional Block The ATA-Disk Module (ADM) includes the ATA controller and flash media, as well as the ATA standard interface. Figure 2-1 shows the functional block diagram. Flash Array Flash Media HOST ATA/IDE Bus Flash Media ATA Controller Flash Media Flash Media Figure 2-1: Functional block diagram 3 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 3. Pin Assignments Table 3-1 lists the pin assignments with respective signal names for the 40-pin configuration. A "#" suffix indicates the active low signal. The pin type can be input, output or input/output. Table 3-1: Pin assignments for the 40-pin configuration Pin No. Signal Name Pin Type 1 RESET# I 3 D7 5 Pin No. Signal Name Pin Type I2U 2 GND - Ground I/O I1Z, O2 4 D8 I/O I1Z, O2 D6 I/O I1Z, O2 6 D9 I/O I1Z, O2 7 D5 I/O I1Z, O2 8 D10 I/O I1Z, O2 9 D4 I/O I1Z, O2 10 D11 I/O I1Z, O2 11 D3 I/O I1Z, O2 12 D12 I/O I1Z, O2 13 D2 I/O I1Z, O2 14 D13 I/O I1Z, O2 15 D1 I/O I1Z, O2 16 D14 I/O I1Z, O2 17 D0 I/O I1Z, O2 18 D15 I/O I1Z, O2 19 GND - Ground 20 NC - Power 21 DMARQ O O1 22 GND I I2Z 24 GND - Ground I I2Z 26 GND - Ground O O1 28 CSEL I I1U 23 IOWR# STOP I/O Type I/O Type Ground IORD# 25 HDMARDY# HSTROBE# IORDY 27 DDMARDY# DSTROBE 29 DMACK# I I2U- 30 NC/WP#* -/I -/I1U 31 INTRQ O O1 32 IOCS16# O O2 33 A1 I I1Z 34 PDIAG# I/O I1U, O1 35 A0 I I1Z 36 A2 I I1Z 37 CS1FX# I I2Z 38 CS3FX# I I2Z 39 DASP# I/O I1U, O6 40 GND - Ground *Pin 30 is selectable as NC or WP# through a zero ohm resistor jumper. Default is NC. Note that pin 30 is a GND pin on standard ATA interface. This pin could be redesigned for host to control the write protect function on ADM 4 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 4. Product Specifications 4.1 Capacity Capacity specification of the ATA-Disk Module (ADM) product family is available as shown in Table 4-1. It lists the specific capacity and the default numbers of heads, sectors and cylinders for each product line. Table 4-1: Capacity specifications Capacity Total bytes* Cylinders Heads Sectors Max LBA 128 MB 128,057,344 977 8 32 250,112 256 MB 256,901,120 980 16 32 501,760 512 MB 512,483,328 993 16 63 1,000,944 1 GB 1,024,966,656 1986 16 63 2,001,888 2 GB 2,048,385,024 3969 16 63 4,000,752 4 GB 4,096,253,952 7937 16 63 8,000,496 8 GB 8,001,552,384 15504 16 63 15,628,032 16 GB 16,001,040,384 16383** 16 63 31,252,032 *Display of total bytes varies from file systems. LBA count addressed in the table above indicates total user storage capacity and will remain the same throughout the lifespan of the device. However, the total usable capacity of the SSD is most likely to be less than the total physical capacity because a small portion of the capacity is reserved for device maintenance usages. 4.2 Performance Performances of the ATA-Flash Disk are listed in Table 4-2. Table 4-2: Performance specifications Capacity 128 MB 256 MB 512 MB 1 GB 2 GB 4 GB 8 GB 16 GB Sustained read (MB/s) 17 17 19 18 20 21 20 20 Sustained write (MB/s) 4 4 7 7 11 13 11 15 Performance Note: Performances vary from flash configurations or host system settings. 5 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 4.3 Environmental Specification Environmental specification of the ATA-Disk Module (ADM) product family follows the MIL-STD-810F standard which is shown in Table 4-4. Table 4-3: Environmental specifications Environment Temperature Specification Operating 0C to 70C; -40C to 85C (Extended Temperature) Storage -40C to 100C Vibration (Non-Operating) Shock (Non-Operating) Sine wave: 10~2000Hz, 15G (X, Y, Z 3-axis) Half sine wave, 1500G, 0.5msec (X, Y, Z ; All 6-axis) 4.4 Endurance The endurance of a storage device is predicted by TeraBytes Written based on several factors related to usage, such as the amount of data written into the drive, block management conditions, and daily workload for the drive. Thus, key factors, such as Write Amplifications and the number of P/E cycles, can influence the lifespan of the drive. The TBW of the device are listed in the following table. Capacity TeraBytes Written 128 MB 3.5 256 MB 6.9 512 MB 14.0 1 GB 27.4 2 GB 45.5 4 GB 54.7 8 GB 80.6 16 GB 129.8 Notes: The measurement assumes the data written to the SSD for test is under a typical and constant rate. The measurement follows the standard metric: 1 TB (Terabyte) = 1000 GB. 6 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 5. Flash Management 5.1. Advanced wear-leveling algorithms Flash memory devices differ from Hard Disk Drives (HDDs) in terms of how blocks are utilized. For HDDs, when a change is made to stored data, like erase or update, the controller mechanism on HDDs will perform overwrites on blocks. Unlike HDDs, flash blocks cannot be overwritten and each P/E cycle wears down the lifespan of blocks gradually. Repeatedly program/erase cycles performed on the same memory cells will eventually cause some blocks to age faster than others. This would bring flash storages to their end of service term sooner. Wear leveling is an important mechanism that level out the wearing of blocks so that the wearing-down of blocks can be almost evenly distributed. This will increase the lifespan of SSDs. Commonly used wear leveling types are Static and Dynamic. 5.2 S.M.A.R.T. technology S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard allowing disk drives to automatically monitor their own health and report potential problems. It protects the user from unscheduled downtime by monitoring and storing critical drive performance and calibration parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer SMART feature adopts the standard SMART command B0h to read data from the drive. When the Apacer SMART Utility running on the host, it analyzes and reports the disk status to the host before the device is in critical condition. 5.3 Built-in hardware ECC The ATA-Disk Module uses BCH Error Detection Code (EDC) and Error Correction Code (ECC) algorithms which correct up to eight random single-bit errors for each 512-byte block of data. High performance is fulfilled through hardware-based error detection and correction. 5.4 Flash block management Current production technology is unable to guarantee total reliability of NAND flash memory array. When a flash memory device leaves factory, it comes with a minimal number of initial bad blocks during production or out-of-factory as there is no currently known technology that produce flash chips free of bad blocks. In addition, bad blocks may develop during program/erase cycles. When host performs program/erase command on a block, bad block may appear in Status Register. Since bad blocks are inevitable, the solution is to keep them in control. Apacer flash devices are programmed with ECC, block mapping technique and S.M.A.R.T to reduce invalidity or error. Once bad blocks are detected, data in those blocks will be transferred to free blocks and error will be corrected by designated algorithms. 5.5 Power Failure Management Power Failure Management plays a crucial role when experiencing unstable power supply. Power disruption may occur when users are storing data into the SSD. In this urgent situation, the controller would run multiple write-to-flash cycles to store the metadata for later block rebuilding. This urgent operation requires about several milliseconds to get it done. At the next power up, the firmware will perform a status tracking to retrieve the mapping table and resume previously programmed NAND blocks to check if there is any incompleteness of transmission. 7 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 5.6 ATA Security Erase ATA Secure Erase is an ATA disk purging command currently embedded in most of the storage drives. Defined in ATA specifications, (ATA) Secure Erase is part of Security Feature Set that allows storage drives to erase all user data areas. The erase process usually runs on the firmware level as most of the ATA-based storage media currently in the market are built-in with this command. ATA Secure Erase can securely wipe out the user data in the drive and protects it from malicious attack. 8 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 6. Software Interface 6.1 Command Set This section defines the software requirements and the format of the commands the host sends to the ATA-Disk Module (ADM). Commands are issued to the ADM by loading the required registers in the command block with the supplied parameters, and then writing the command code to the Command register. The manner in which a command is accepted varies. Table 6-1: Command set (1 of 2) Command Code Check-Power-Mode E5H or 98H Execute-Drive-Diagnostic 90H Erase Sector(s) C0H Flush-Cache E7H Format Track 50H Identify-Drive ECH Idle E3H or 97H Idle-Immediate E1H or 95H Initialize-Drive-Parameters 91H NOP 00H Read-Buffer E4H Read-DMA C8H or C9H Read-Multiple C4H Read-Sector(s) 20H or 21H Read-Verify-Sector(s) 40H or 41H Recalibrate 1XH Request-Sense 03H Security-Disable-Password F6H Security-Erase-Prepare F3H Security-Erase-Unit F4H Security-Freeze-Lock F5H Security-Set-Password F1H Security-Unlock F2H Seek 7XH Set-Features EFH 9 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX Table 6-1: Command set (2 of 2) Command Code SMART B0H Set-Multiple-Mode C6H Set-Sleep-Mode E6H or 99H Standby E2H or 96H Standby-lmmediate E0H or 94H Translate-Sector 87H Write-Buffer E8H Write-DMA CAH or CBH Write-Multiple C5H Write-Multiple-Without-Erase CDH Write-Sector(s) 30H or 31H Write-Sector-Without-Erase 38H Write-Verify 3CH 10 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 7. Electrical Specification Caution: Absolute Maximum Stress Ratings - Applied conditions greater than those listed under "Absolute Maximum Stress Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability. Table 7-1: Operating range Standard Operating Temperature 0C to +70C Extended Operating Temperature -40C to +85C Supply voltage 5V 5% (4.75-5.25V) 3.3V 5% (3.135-3.465V) Table 7-2: Absolute maximum power pin stress ratings Parameter Symbol Input Power Voltage on any pin except VDD with respect to GND VDD V Conditions -0.3V min. to 6.5V max. -0.5V min. to VDD + 0.5V max. Table 7-3: Recommended system power-up timing Symbol Parameter 1 TPU-READY 1 TPU-WRITE Power-up to Ready Operation Power-up to Write Operation Typical Maximum Units 200 200 1000 1000 ms ms 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. 11 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 8. Physical Characteristics 8.1 Dimension 8.1.1 40 pin/ 90 degree Pin 20 blocked 12 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 8.1.2 40 pin/ 90 degree Pin 20 unblocked 13 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 9. Product Ordering Information 9.1 Product Code Designations AP - FM xxxx E X 0 S X R - Q T X Temperature: Blank: Standard W: Extended temperature Flash Type FW Version Environmental Spec Voltage: 3: 3.3V 5: 5.0V Performance: S: Standard PCB Version Package Modifier: 3: 40 pin/ 90D Pin 20 blocked F: 40 pin/ 90D Pin 20 unblocked Controller Version Capacity: 0128: 0256: 0512: 001G: 002G: 004G: 008G: 016G: 128MB 256MB 512MB 1GB 2GB 4GB 8GB 16GB Model Name Apacer Product Code 14 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 9.2 Valid Combinations 9.2.1 Standard (Pin 20 blocked) Capacity Model Number (3.3V) Model Number (5V) 128MB AP-FM0128E30S3R-QT AP-FM0128E30S5R-QT 256MB AP-FM0256E30S3R-QT AP-FM0256E30S5R-QT 512MB AP-FM0512E30S3R-QT AP-FM0512E30S5R-QT 1GB AP-FM001GE30S3R-QT AP-FM001GE30S5R-QT 2GB AP-FM002GE30S3R-QT AP-FM002GE30S5R-QT 4GB AP-FM004GE30S3R-QT AP-FM004GE30S5R-QT 8GB AP-FM008GE30S3R-QT AP-FM008GE30S5R-QT 16GB AP-FM016GE30S3R-QT AP-FM016GE30S5R-QT 9.2.2 Ext. Temp (Pin 20 blocked) Capacity Model Number (3.3V) Model Number (5V) 128MB AP-FM0128E30S3R-QTW AP-FM0128E30S5R-QTW 256MB AP-FM0256E30S3R-QTW AP-FM0256E30S5R-QTW 512MB AP-FM0512E30S3R-QTW AP-FM0512E30S5R-QTW 1GB AP-FM001GE30S3R-QTW AP-FM001GE30S5R-QTW 2GB AP-FM002GE30S3R-QTW AP-FM002GE30S5R-QTW 4GB AP-FM004GE30S3R-QTW AP-FM004GE30S5R-QTW 8GB AP-FM008GE30S3R-QTW AP-FM008GE30S5R-QTW 16GB AP-FM016GE30S3R-QTW AP-FM016GE30S5R-QTW 9.2.3 Standard (Pin 20 unblocked) Capacity Model Number (3.3V) Model Number (5V) 128MB AP-FM0128EF0S3R-QT AP-FM0128EF0S5R-QT 256MB AP-FM0256EF0S3R-QT AP-FM0256EF0S5R-QT 512MB AP-FM0512EF0S3R-QT AP-FM0512EF0S5R-QT 1GB AP-FM001GEF0S3R-QT AP-FM001GEF0S5R-QT 2GB AP-FM002GEF0S3R-QT AP-FM002GEF0S5R-QT 4GB AP-FM004GEF0S3R-QT AP-FM004GEF0S5R-QT 8GB AP-FM008GEF0S3R-QT AP-FM008GEF0S5R-QT 16GB AP-FM016GEF0S3R-QT AP-FM016GEF0S5R-QT 15 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX 9.2.4 Ext. Temp (Pin 20 unblocked) Capacity Model Number (3.3V) Model Number (5V) 128MB AP-FM0128EF0S3R-QTW AP-FM0128EF0S5R-QTW 256MB AP-FM0256EF0S3R-QTW AP-FM0256EF0S5R-QTW 512MB AP-FM0512EF0S3R-QTW AP-FM0512EF0S5R-QTW 1GB AP-FM001GEF0S3R-QTW AP-FM001GEF0S5R-QTW 2GB AP-FM002GEF0S3R-QTW AP-FM002GEF0S5R-QTW 4GB AP-FM004GEF0S3R-QTW AP-FM004GEF0S5R-QTW 8GB AP-FM008GEF0S3R-QTW AP-FM008GEF0S5R-QTW 16GB AP-FM016GEF0S3R-QTW AP-FM016GEF0S5R-QTW 16 (c) 2013 Apacer Technology Inc. Rev. 1.6 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX Revision History Revision Date Description 1.0 01/19/2009 Official release 1.1 02/11/2009 Modified document layout 1.2 03/26/2009 Updated valid combination wording 1.3 03/03/2011 Updated Product Ordering Information 1.4 04/20/2011 1.5 01/09/2012 Remark Updated Product Ordering Information & Physical Characteristics Revised the title name Original 9.2.5 Standard (Pin 20 blocked) 9.2.6 Hi-Speed (Pin 20 blocked) 9.2.7 Ext. Temp Standard (Pin 20 blocked) 9.2.8 Ext. Temp Hi-Speed (Pin 20 blocked) New 9.2.5 Standard (Pin 20 unblocked) 9.2.6 Hi-Speed (Pin 20 unblocked) 9.2.7 Ext. Temp Standard (Pin 20 unblocked) 9.2.8 Ext. Temp Hi-Speed (Pin 20 unblocked) Updated performance and product ordering information due to change in NAND flash use 1.6 08/11/2013 Updated the address of Taiwan headquarter Added endurance TBW section 1.7 09/05/2013 Corrected the product ordering information 17 (c) 2013 Apacer Technology Inc. Rev. 1.7 Value Added ATA-Disk Module AP-FMxxxxEX0SXR-QTX Global Presence Taiwan (Headquarters) Apacer Technology Inc. Apacer Technology Inc. 1F., No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City 236, Taiwan R.O.C. Tel: 886-2-2267-8000 Fax: 886-2-2267-2261 amtsales@apacer.com U.S.A. Apacer Memory America, Inc. 386 Fairview Way, Suite102, Milpitas, CA 95035 Tel: 1-408-518-8699 Fax: 1-408-935-9611 sa@apacerus.com Japan Apacer Technology Corp. 5F, Matsura Bldg., Shiba, Minato-Ku Tokyo, 105-0014, Japan Tel: 81-3-5419-2668 Fax: 81-3-5419-0018 jpservices@apacer.com Europe Apacer Technology B.V. Science Park Eindhoven 5051 5692 EB Son, The Netherlands Tel: 31-40-267-0000 Fax: 31-40-267-0000#6199 sales@apacer.nl China Apacer Electronic (Shanghai) Co., Ltd 1301, No.251,Xiaomuqiao Road, Shanghai, 200032, China Tel: 86-21-5529-0222 Fax: 86-21-5206-6939 sales@apacer.com.cn India Apacer Technologies Pvt. Ltd. # 535, 1st Floor, 8th cross, JP Nagar 3rd Phase, Bangalore - 560078, India Tel: 91-80-4152-9061 sales_india@apacer.com 18 (c) 2013 Apacer Technology Inc. Rev. 1.7 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apacer: AP-FM0128E30S5R-QT AP-FM0256E30S5R-QT AP-FM0512E30S5R-QT AP-FM001GE30S5R-QT APFM002GE30S5R-QT AP-FM004GE30S5R-QT AP-FM008GE30S5R-QT AP-FM016GE30S5R-QT APFM0256E30S5R-QTW AP-FM0512E30S5R-QTW AP-FM001GE30S5R-QTW AP-FM002GE30S5R-QTW APFM004GE30S5R-QTW AP-FM008GE30S5R-QTW AP-FM0128E30S5R-QTW AP-FM016GE30S5R-QTW