W24257 32K x 8 CMOS STATIC RAM GENERAL DESCRIPTION The W24257 is a slow speed, low power CMOS static RAM organized as 32768 x 8 bits that operates on a single 5-volt power supply. This device is manufactured using Winbond's high performance CMOS technology. FEATURES Low power consumption: - Active: 325 mW (max.) - Standby: 75 W (max.) (LL-version) 150 W (max.) (L-version) * Access time: 70 nS (max.) * Single +5V power supply * Fully static operation * PIN CONFIGURATIONS BLOCK DIAGRAM * All inputs and outputs directly TTL compatible Three-state outputs * Battery back-up operation capability * Data retention voltage: 2V (min.) * Packaged in 28-pin 330 mil SOP, standard type one TSOP (8 mm x 13.4 mm ) * V DD V SS A14 1 28 V DD A12 2 27 #WE A7 3 26 A13 A0 A6 A5 4 5 25 24 A8 . A9 . A4 A3 6 7 28-pin 23 A11 A2 8 SOP A1 9 10 20 #CS 19 I/O8 A0 22 #OE 21 A10 I/O1 11 18 I/O7 I/O2 12 17 I/O6 I/O3 V SS 13 16 I/O5 14 15 I/O4 DECODER CORE ARRAY A14 #CS #OE CONTROL DATA I/O I/O8 #WE #OE A11 A9 A8 A13 #WE V DD A14 A12 A7 A6 A5 A4 A3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28-pin TSOP 28 27 26 25 24 23 22 21 20 19 18 17 16 15 A10 I/O1 . . PIN DESCRIPTION #CS I/O 8 SYMBOL I/O 7 I/O 6 A0-A14 I/O 5 I/O 4 I/O1-I/O8 #CS #WE #OE VDD VSS V SS I/O 3 I/O 2 I/O 1 A0 A1 A2 -1- DESCRIPTION Address Inputs Data Inputs/Outputs Chip Select Input Write Enable Input Output Enable Input Power Supply Ground Publication Release Date: February 2001 Revision A16 W24257 TRUTH TABLE #CS #OE #WE MODE H X X Not Selected High Z ISB, ISB1 L H H Output Disable High Z IDD L L H Read Data Out IDD L X L Write Data In IDD VDD CURRENT I/O1-I/O8 DC CHARACTERISTICS Absolute Maximum Ratings PARAMETER RATING UNIT -0.5 to +7.0 V -0.5 to VDD +0.5 V Supply Voltage to VSS Potential Input/Output to VSS Potential Allowable Power Dissipation Storage Temperature 1.0 W -65 to +150 C 0 to +70 C Operating Temperature Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. Operating Characteristics (VDD = 5V 10%, VSS = 0V, TA = 0 to 70 C for LL/L; -20 to 85 C for LE) PARAMETER SYM. TEST CONDITIONS MIN. TYP. MAX. UNIT Input Low Voltage VIL - -0.5 - +0.8 V Input High Voltage VIH - +2.2 - VDD +0.5 V Input Leakage Current ILI VIN = VSS to VDD -2 - +2 A Output Leakage Current ILO VI/O = VSS to VDD, #CS = VIH (min.) or #OE = VIH (min.) or #WE = VIL (max.) -2 - +2 A Output Low Voltage VOL IOL = +4.0 mA - - 0.4 V Output High Voltage VOH IOH = -1.0 mA 2.4 - - V Operating Power Supply Current IDD #CS = VIL (min.), I/O = 0 mA Cycle = min., Duty = 100% - - 70 mA Standby Power Supply Current ISB #CS = VIH (min.) Cycle = min., Duty = 100% - - 3 mA ISB1 #CS VDD -0.2V LL/LE - - 15 A L - - 30 A Note: Typical characteristics are at VDD = 5V, TA = 25 C. -2- W24257 CAPACITANCE (VDD = 5V, TA = 25 C, f = 1 MHz) PARAMETER SYM. CONDITIONS MAX. UNIT Input Capacitance CIN VIN = 0V 6 pF Input/Output Capacitance CI/O VOUT = 0V 8 pF Note: These parameters are sampled but not 100% tested. AC CHARACTERISTICS AC Test Conditions PARAMETER CONDITIONS Input Pulse Levels 0.6V to 2.4V Input Rise and Fall Times 5 nS Input and Output Timing Reference Level 1.5V Output Load CL = 100 pF, IOH/IOL = -1 mA/4 mA AC Test Loads and Waveform R1 1000 ohm 5V R1 1000 ohm 5V OUTPUT OUTPUT 5 pF 100 pF Including Jig and Scope R2 660 ohm Including Jig and Scope R2 660 ohm (For TCLZ, TOLZ, TCHZ, TOHZ , TWHZ , TOW) 3.0V 90% 10% 0V 90% 10% 5 nS 5 nS -3- Publication Release Date: February 2001 Revision A16 W24257 AC Characteristics, continued (VDD = 5V 10%, VSS = 0V, TA = 0 to 70 C for LL/L; -20 to 85 C for LE) Read Cycle PARAMETER SYMBOL W24257-70 UNIT MIN. MAX. Read Cycle Time TRC 70 - nS Address Access Time TAA - 70 nS Chip Select Access Time TACS - 70 nS Output Enable to Output Valid TAOE - 35 nS Chip Selection to Output in Low Z TCLZ* 10 - nS Output Enable to Output in Low Z TOLZ* 5 - nS Chip Deselection to Output in High Z TCHZ* - 30 nS Output Disable to Output in High Z TOHZ* - 30 nS Output Hold from Address Change TOH 10 - nS These parameters are sampled but not 100% tested Write Cycle PARAMETER W24257-70 SYMBOL UNIT MIN. MAX. Write Cycle Time TWC 70 - nS Chip Selection to End of Write TCW 60 - nS Address Valid to End of Write TAW 60 - nS Address Setup Time TAS 0 - nS Write Pulse Width TWP 45 - nS TWR 0 - nS Data Valid to End of Write TDW 30 - nS Data Hold from End of Write TDH 0 - nS Write to Output in High Z TWHZ* - 30 nS Output Disable to Output in High Z TOHZ* - 30 nS Output Active from End of Write TOW 0 - nS Write Recovery Time #CS, #WE These parameters are sampled but not 100% tested -4- W24257 TIMING WAVEFORMS Read Cycle 1 (Address Controlled) TRC Address TAA TOH TOH DOUT Read Cycle 2 (Chip Select Controlled) #CS TACS TCHZ TCLZ D OUT Read Cycle 3 (Output Enable Controlled) T RC Address T AA #OE TOH T AOE T OLZ #CS T OHZ T ACS D OUT T CHZ T CLZ -5- Publication Release Date: February 2001 Revision A16 W24257 Timing Waveforms, continued Write Cycle 1 TW C Address TW R #OE TC W #CS TA W #WE TWP TAS TO H Z (1, 4) D OUT TD W TD H D IN Write Cycle 2 (OE = VIL Fixed) T WC Address TW R TC W #CS TA W #WE TWP TA S TO H TW H Z (1, 4) D OUT TD W (2) (3) TO W TD H D IN Notes: 1. During this period, I/O pins are in the output state, so input signals of opposite phase to the outputs should not be applied. 2. The data output from DOUT are the same as the data written to DIN during the write cycle. 3. DOUT provides the read data for the next address. 4. Transition is measured 500 mV from steady state with CL = 5 pF. This parameter is guaranteed but not 100% tested. -6- W24257 DATA RETENTION CHARACTERISTICS (TA = 0 to 70 C for LL/L; -20 to 85 C for LE ) PARAMETER SYM. TEST CONDITIONS MIN. TYP. MAX. UNIT VDD for Data Retention VDR #CS VDD -0.2V 2.0 - - V Data Retention Current IDDDR #CS VDD -0.2V LL/LE - - 15 A - - 30 A 0 - - nS TRC* - - nS VDD = 3V L Chip Deselect to Data Retention Time TCDR See data retention Operation Recovery Time TR Waveform TRC* = Read Cycle Time DATA RETENTION WAVEFORM DATA RETENTION MODE V DD 4.5V VDR > = 2V 4.5V TR TC D R #CS1 > = V D D -0.2V V IH #CS V IH ORDERING INFORMATION PART NO. ACCESS OPERATING CURRENT TIME (nS) MAX. (mA) STANDBY CURRENT MAX. (A) OPERATING TEMP. (C) PACKAGE W24257S-70LL 70 70 15 0 to 70 330 mil SOP W24257S-70L 70 70 30 0 to 70 330 mil SOP W24257S-70LE 70 70 15 -20 to 85 330 mil SOP W24257Q-70LL 70 70 15 0 to 70 Standard type one TSOP W24257Q-70L 70 70 30 0 to 70 Standard type one TSOP W24257Q-70LE 70 70 15 -20 to 85 Standard type one TSOP Notes: 1. Winbond reserves the right to make changes to its products without prior notice. 2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications where personal injury might occur as a consequence of product failure. -7- Publication Release Date: February 2001 Revision A16 W24257 BONDING PAD DIAGRAM 6 5 4 3 A4 A5 A6 A7 A12 A14 VDD VDD WEB A13 2 1 30 29 28 27 26 25 24 A8 A9 A11 AC5394 23 7 A3 OEB Y X 8 22 A2 A10 9 A1 10 11 12 13 14 A0 I/O0 I/O1 I/O2 VSS 15 16 17 18 19 20 21 VSS I/O3 I/O4 I/O5 I/O6 I/O7 CSB PAD NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 X -232.25 -351.70 -471.15 -590.60 -710.05 -829.50 -992.79 -992.79 -857.86 -738.41 -594.84 -451.06 -310.67 -171.78 24.45 151.80 298.07 443.28 588.20 732.84 871.11 992.75 992.75 810.09 690.64 571.19 451.74 332.29 120.25 -93.23 Y 1445.22 1445.22 1445.22 1445.22 1445.22 1445.22 1362.24 -1306.11 -1452.79 -1452.79 -1414.13 -1414.13 -1414.13 -1405.28 -1405.28 -1414.13 -1414.13 -1414.13 -1414.13 -1414.13 -1452.79 -1312.15 1373.67 1445.22 1445.22 1445.22 1445.22 1445.22 1444.65 1444.65 Note: For bare chip form (C.O.B.) applications, the substrate must be connected to VDD or left floating in the PCB layout. -8- Publication Release Date: January 2001 Revision A16 W24257 PACKAGE DIMENSIONS 28-pin SO Wide Body Symbol 28 A A1 A2 b c D E e HE L LE S y 15 e1 E HE L Detail F 14 1 b Dimension in Inches Dimension in mm Min. Nom. Max. Min. Nom. Max. 2.85 0.112 0.004 0.10 0.093 0.098 0.103 2.36 2.49 0.014 0.016 0.020 0.36 0.41 0.51 0.008 0.010 0.014 0.20 0.25 0.36 18.11 18.62 2.62 0.713 0.733 0.326 0.331 0.336 8.28 8.41 8.53 0.044 0.050 0.056 1.12 1.27 1.42 0.453 0.465 0.477 11.51 11.81 12.12 0.028 0.036 0.044 0.71 0.91 1.12 0.059 0.067 0.075 1.50 1.70 1.91 0.047 1.19 0.10 0.004 10 0 10 0 Notes: 1. Dimension D Max. & S include mold flash or tie bar burrs. 2. Dimension b does not include dambar protrusion/intrusion. 3. Dimension D & E include mold mismatch . and determined at the mold parting line. 4. Controlling dimension: Inches. 5. General appearance spec should be based on final visual inspection spec. e1 D c A2 A S e y LE A1 See Detail F Seating Plane 28-pin Standard Type One TSOP HD Dimension In Inches Dimension In mm Symbol D Min. c A A1 A2 b c D E HD e L L1 Y 1 e E b A2 A A1 L Nom. Max. Min. Nom. 0.006 0.002 Max. 1.20 0.047 0.05 0.15 0.035 0.040 0.041 0.95 1.00 0.007 0.008 0.011 0.17 0.20 0.27 0.004 0.006 0.008 0.10 0.15 0.21 11.90 1.05 0.461 0.465 0.469 11.70 11.80 0.311 0.315 0.319 7.90 8.00 8.10 0.520 0.528 0.536 13.20 13.40 13.60 0.020 0.024 0.028 0.50 0.60 0.022 0.55 0.010 0.000 0 3 0.70 0.25 0.004 0.00 5 0 0.10 3 5 Controlling dimension: Millimeters Y L1 -9- Publication Release Date: January 2001 Revision A16 W24257 VERSION HISTORY VERSION DATE PAGE A12 Nov. 1999 1, 2, 7 4, 7 A13 Apr. 2000 7 A14 May 2000 1, 7, 8 A15 A16 Nov. 2000 Feb. 2001 Headquarters DESCRIPTION Change the IDD, ISB, ISB1 Remove the W24257-10 spc. Typo correction in Standby Current Max.: mA->A Delete 28-pin DIP Package 8 Add in Bonding Pad Diagram 2 Modify Operating Power Supply Current (IDD) as 70 mA 1 Add in TSOP Pin Configuration 2, 4, 7 Add in LE grade Winbond Electronics (H.K.) Ltd. Unit 9-15, 22F, Millennium City, No. 4, Creation Rd. III, No. 378 Kwun Tong Rd; Science-Based Industrial Park, Kowloon, Hong Kong Hsinchu, Taiwan TEL: 852-27513100 TEL: 886-3-5770066 FAX: 852-27552064 FAX: 886-3-5796096 http://www.winbond.com.tw/ Voice & Fax-on-demand: 886-2-27197006 Taipei Office 11F, No. 115, Sec. 3, Min-Sheng East Rd., Taipei, Taiwan TEL: 886-2-27190505 FAX: 886-2-27197502 Note: All data and specifications are subject to change withou t notice. - 10 - Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408-9436666 FAX: 408-5441798